Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “single experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

An experimental study of fuel injection strategies in CAI gasoline engine

Combustion of gasoline in a direct injection controlled auto-ignition (CAI) single-cylinder research engine was studied. CAI operation was achieved with the use of the negative valve overlap (NVO) technique and internal exhaust gas re-circulation (EGR). Experiments were performed at single injection and split injection, where some amount of fuel was injected close to top dead centre (TDC) during NVO interval, and the second injection was applied with variable timing. Additionally, combustion at variable fuel-rail pressure was examined. Investigation showed that at fuel injection into recompressed exhaust fuel reforming took place. This process was identified via an analysis of the exhaust-fuel mixture composition after NVO interval. It was found that at single fuel injection in NVO phase, its advance determined the heat release rate and auto-ignition timing, and had a strong influence on NO{sub X} emission. However, a delay of single injection to intake stroke resulted in deterioration of cycle-to-cycle variability. Application of split injection showed benefits of this strategy versus single injection. Examinations of different fuel mass split ratios and variable second injection timing resulted in further optimisation of mixture formation. At equal share of the fuel mass injected in the first injection during NVO and in the second injection at the beginning of compression, the lowest emission level and cyclic variability improvement were observed. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Observation of 𝑡⁢𝑊⁢𝑍 Production at the CMS Experiment

The first observation of single top quark production in association with a 𝑊 and a 𝑍 boson in proton-proton collisions is reported. The analysis uses data at center-of-mass energies of 13 and 13.6 TeV recorded with the CMS detector at the CERN LHC, corresponding to a total integrated luminosity of 200 fb −1 . Events with three or four charged leptons, which can be electrons or muons, are selected. Advanced machine-learning algorithms and improved reconstruction methods, compared to an earlier analysis, result in an unprecedented sensitivity to 𝑡⁢𝑊⁢𝑍 production. The measured cross sections for 𝑡⁢𝑊⁢𝑍 production are 248 ± 52 fb and 242 ± 77 fb for $\sqrt{s}$ =13 and 13.6 TeV, respectively. The signal is established with a statistical significance of 5.8 standard deviations, with 3.5 expected, compared to the background-only hypothesis.

Hayrapetyan, Aram [Yerevan Physics Institute]↗

Pattern Recognition: The Importance of Dispersion in Crystal Collimation

One aspect of the upcoming CRYSTAL experiment is to study the dynamics of single protons circulating the SPS in the presence of a crystal. Under some circumstances (for example under crystal channeling) a proton may hit the crystal and the neighboring silicon strip position detectors only once, before extraction from the SPS. In general (at most crystal rotation angles) it is expected that single protons will hit the crystal many times, with many accelerator turns between each hit, before escaping. Intermediate regimes are also possible (for example under volume reflection) in which a proton hits the crystal only a few times over many turns before being lost. It is crucial that the data analysis of each single proton data set be able to distinguish between these different dynamical phases, and to be able to convincingly demonstrate that the fundamental processes at play in each phase are well understood. Distinguishing between dynamical phases depends crucially on the ability to perform pattern recognition--at least visually, but preferably quantitatively--on the single proton data sets. This note shows that synchrotron oscillations significantly affect the hit pattern of a proton on the crystal. (By hit pattern we mean either the measurement vector of turn number and penetration depth, for each proton, or a vector that can be directly derived from the measurement vector, such as the vector of inferred synchrotron phase and penetration depth.) The analysis is (deliberately) as rudimentary as possible, using an elementary linear calculation which neither includes any higher order effects in the accelerator, nor any dynamical interactions between the test proton and the crystal or the silicon detectors. Single particle simulation studies need to be carried out for CRYSTAL, exploring realistic effects besides dispersion, such as multiple scattering, dead zones, energy loss, dispersion slope, and linear coupling. Only after analysis software becomes available to interpret the output of such studies will it be possible to predict with any confidence that it will be possible to distinguish all single proton dynamical phases in the CRYSTAL experiment. Then reality will prevail.

43 PARTICLE ACCELERATORS↗

Interface markings in crystals experiment MA-060

Doped germanium single crystals with interface demarcation were successfully grown during the Apollo Soyuz Test Project mission. Interface demarcation permitted the determination of the microscopic growth behavior from the onset to the termination of solidification. Preliminary segregation analysis shows striking differences in segregation in the presence of gravity. The correlation between microscopic growth rate behavior and the composition of the solid on the microscale is being evaluated.

Gatos, H. C.↗

Friction, deformation and fracture of single-crystal silicon carbide

Friction experiments were conducted with hemispherical and conical diamond riders sliding on the basal plane of silicon carbide. The results indicate that, when deformation is primarily elastic, the friction does not depend on crystallographic orientation and there is no detectable fracture or cracking. When, however, plastic deformation occurs, silicon carbide exhibits anisotropic friction and deformation behavior. Surface fracture crack patterns surrounding wear tracks are observed to be of three types. The crack-geometries of two types are generally independent of orientation, the third crack, however, depends on the orientation. All surface cracks extend into subsurface. Anisotropic friction, deformation and fracture on the basal plane are primarily controlled by the slip system and cleavage.

Miyoshi, K.↗

Adhesion, friction, and wear of binary alloys in contact with single-crystal silicon carbide

Sliding friction experiments, conducted with various iron base alloys (alloying elements are Ti, Cr, Mn, Ni, Rh and W) in contact with a single crystal silicon carbide /0001/ surface in vacuum are discussed. Results indicate atomic size misfit and concentration of alloying elements play a dominant role in controlling adhesion, friction, and wear properties of iron-base binary alloys. The controlling mechanism of the alloy properties is as an intrinsic effect involving the resistance to shear fracture of cohesive bonding in the alloy. The coefficient of friction generally increases with an increase in solute concentration. The coefficient of friction increases as the solute-to-iron atomic radius ratio increases or decreases from unity. Alloys having higher solute concentration produce more transfer to silicon carbide than do alloys having low solute concentrations. The chemical activity of the alloying element is also an important parameter in controlling adhesion and friction of alloys.

Miyoshi, K.↗

Annoyance caused by advanced turboprop aircraft flyover noise: Single-rotating propeller configuration

Two experiments were conducted to quantify the annoyance of people to advanced turboprop (propfan) aircraft flyover noise. The objectives were to: (1) determine the effects on annoyance of various tonal characteristics; and (2) compare annoyance to advanced turboprops with annoyance to conventional turboprops and jets. A computer was used to produce realistic, time-varying simulations of advanced turboprop aircraft takeoff noise. In the first experiment, subjects judged the annoyance of 45 advanced turboprop noises in which the tonal content was systematically varied to represent the factorial combinations of five fundamental frequencies, three frequency envelope shapes, and three tone-to-broadband noise ratios. Each noise was presented at three sound levels. In the second experiment, 18 advanced turboprop takeoffs, 5 conventional turboprop takeoffs, and 5 conventional jet takeoffs were presented at three sound pressure levels to subjects. Analysis indicated that frequency envelope shape did not significantly affect annoyance. The interaction of fundamental frequency with tone-to-broadband noise ratio did have a large and complex effect on annoyance. The advanced turboprop stimuli were slightly less annoying than the conventional stimuli.

Mccurdy, David A.↗

Simulation motion effect on single axis compensatory tracking

An experiment that examined how changes in a motion platform drive filter affect pilot-vehicle performance and opinion was conducted on the NASA Ames Vertical Motion Simulator. Pilots controlled a simplified helicopter model in the vertical or the directional axis and tracked a randomly moving target aircraft in the presence of a random disturbance. With both tasks, variations from full motion to fixed-base conditions were made in the high-pass drive filter gain and natural frequency. The results indicate that vertical motion did not affect the open-loop pilot-vehicle target-tracking crossover frequency, but target-tracking phase margins improved with increased filter gain or decreased natural frequency. Vertical disturbance-rejection crossover frequency increased with decreasing filter natural frequency, while disturbance rejection phase margins improved with increasing filter gain. Vertical tracking errors increased significantly when all vertical motion was removed. No significant differences were measured among the directional configurations, which indicates that pure yaw motion cues may not be as important as previously thought in flight simulation.

Schroeder, Jeffery A.↗

Influence of the Gas Pressure on Single-wall Carbon Nanotubes Formation

Experiments and modeling have been performed to predict the effect of gas pressure on species distribution and nanotube growth rate under specific conditions of synthesis of singlewall carbon nanotubes (SWCNTs) by arc discharge. Numerical results were compared with experiments in order to find a consistent correlation between the nanotube growth and the pressure. We used argon and helium as buffer gases with a total pressure varied between 0.1 and 1 bar. We experimentally observed that both the anode erosion rate and the Brunauer-Emmett-Teller (BET) surface area of the as produced nanotube soot material are very sensitive to the total gas pressure in the reactor

Hinkov, I.↗

Isentropic compression studies using the NHMFL single turn

Magnetic isentropic compression experiments (ICE) provide the most accurate shock free compression data for materials at megabar stresses. Recent ICE experiments performed on the Sandia Z-machine (Asay, 1999) and at the Los Alamos High Explosive Pulsed Power facility (Tasker, 2006) are providing our nation with data on material properties in extreme dynamic high stress environments. The LANL National High Magnetic Field Laboratory (NHMFL) can offer a less complex ICE experiment at high stresses (up to {approx}1Mbar) with a high sample throughput and relatively low cost. This is not to say that the NHMFL technique will replace the other methods but rather complement them. For example, NHMFL-ICE is ideal for the development of advanced diagnostics, e.g., to detect phase changes. We will discuss the physics of the NHMFL-ICE experiments and present data from the first proof-of-principle experiments that were performed in September 2010.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The viscosity to entropy density ratio from PHENIX data on single electron production

The PHENIX experiment has measured electrons from the decay of hadrons carrying heavy flavor (charm or bottom quarks) in p + p and Au + Au collisions at {radical}s{sub NN} = 200 GeV at the Relativistic Heavy Ion Collider (RHIC). The strong damping of heavy-flavor motion through the medium is reflected in a substantial suppression at high p{sub T} and a large azimuthal anisotropy {upsilon}{sub 2} of such electrons in Au + Au collisions at RHIC. By requiring a simultaneous description of the nuclear modification factor R{sub AA}(p{sub T}) and the azimuthal anisotropy {upsilon}{sub 2}(p{sub T}) in transport models, the viscosity to entropy density ratio of the medium can be estimated as {eta}/s {approx} (1.3-2)(1/4{pi}), which is close to the conjectured lower quantum bound and, therefore, near a perfect fluid.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Non Radiation Hardened Microprocessors in Spaced Based Remote Sensing Systems

The CALIPSO (Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations) mission is a comprehensive suite of active and passive sensors including a 20Hz 230mj Nd:YAG lidar, a visible wavelength Earth-looking camera and an imaging infrared radiometer. CALIPSO flies in formation with the Earth Observing System Post-Meridian (EOS PM) train, provides continuous, near-simultaneous measurements and is a planned 3 year mission. CALIPSO was launched into a 98 degree sun synchronous Earth orbit in April of 2006 to study clouds and aerosols and acquires over 5 gigabytes of data every 24 hours. The ground track of one CALIPSO orbit as well as high and low intensity South Atlantic Anomaly outlines is shown. CALIPSO passes through the SAA several times each day. Spaced based remote sensing systems that include multiple instruments and/or instruments such as lidar generate large volumes of data and require robust real-time hardware and software mechanisms and high throughput processors. Due to onboard storage restrictions and telemetry downlink limitations these systems must pre-process and reduce the data before sending it to the ground. This onboard processing and realtime requirement load may mean that newer more powerful processors are needed even though acceptable radiation-hardened versions have not yet been released. CALIPSO's single board computer payload controller processor is actually a set of four (4) voting non-radiation hardened COTS Power PC 603r's built on a single width VME card by General Dynamics Advanced Information Systems (GDAIS). Significant radiation concerns for CALIPSO and other Low Earth Orbit (LEO) satellites include the South Atlantic Anomaly (SAA), the north and south poles and strong solar events. Over much of South America and extending into the South Atlantic Ocean the Van Allen radiation belts dip to just 200-800km and spacecraft entering this area are subjected to high energy protons and experience higher than normal Single Event Upset (SEU) and Single Event Latch-up (SEL) rates. Although less significant, spacecraft flying in the area around the poles experience similar upsets. Finally, powerful solar proton events in the range of 10MeV/10pfu to 100MeV/1pfu as are forecasted and tracked by NOAA's Space Environment Center in Colorado can result in Single Event Upset (SEU), Single Event Latch-up (SEL) and permanent failures such as Single Event Gate Rupture (SEGR) in some technologies. (Galactic Cosmic Rays (GCRs) are another source, especially for gate rupture) CALIPSO mitigates common radiation concerns in its data handling through the use of redundant processors, radiation-hardened Application Specific Integrated Circuits (ASIC), hardware-based Error Detection and Correction (EDAC), processor and memory scrubbing, redundant boot code and mirrored files. After presenting a system overview this paper will expand on each of these strategies. Where applicable, related on-orbit data collected since the CALIPSO initial boot on May 4, 2006 will be noted.

Decoursey, Robert J.↗

Splitting Mono- and Di-Branched Alkane Isomers by a Robust Aluminum-Based Metal-Organic Framework Material with Optimal Pore Dimensions

The separation of alkanes with different degrees of branching, particularly mono- and dibranched isomers, represents a challenging yet important industrial process for the production of premium gasoline blending components with high octane number. We report here the separation of linear/monobranched and dibranched alkanes through complete molecular sieving by a robust aluminum-based MOF material, Al-bttotb (H 3 bttotb = 4,4',4"-(benzene-1,3,5-triyltris(oxy))tribenzoicacid). Single- and multicomponent adsorption experiments reveal that the material adsorbs linear and monobranched alkanes, but fully excludes their dibranched isomers. Adsorption sites of alkanes within the MOF channels have been identified by single-crystal X-ray diffraction studies, and the adsorption mechanism was explored through computational calculations and modeling. The highly selective adsorption of the MOF should be attributed to its optimal pore dimensions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design of SSR1 Single Spoke Resonators for PXIE

The Project X Injector Experiment (PXIE) at Fermilab contains one cryomodule of Single Spoke Resonators operating at 325 MHz with a geometrical beta of 0.2. Two prototypes have been tested successfully at high gradients in the Fermilab Vertica l Test Stand (VTS). We have welded a Stainless Steel helium vessel on the first prototype and tested it in the spoke-dedicated Test Cryostat. With excellent results in hand, an order for ten bare resonators was placed with US industry. A new design for th e helium vessel was developed for these resonators with the main goal of reducing the sensitivity of the resonator to variations of the helium pressure to meet the requirements of PXIE. A new tuner was developed despite the good results of the first proto type. The new design was inevitable due to the different behavior of the resonator in the new helium vessel. Other aspects were improved such as the maintainability of the tuner motor and piezoelectric actuators allowing their replacement from access port s on the cryomodule's vacuum vessel.

43 PARTICLE ACCELERATORS↗

Triplet Excitons in Pentacene Are Intrinsically Difficult to Dissociate via Charge Transfer

Singlet fission (SF) has the potential to bypass the Shockley–Queisser limit for solar cell efficiency through the production of two electron–hole pairs per photon. However, in polycrystalline pentacene this goal is hindered by slow charge transfer from triplets (=10 7 s –1 ) after SF. In this paper we demonstrate that slow charge transfer is an intrinsic property of triplet states in this material and most likely not connected with the triplet pair states that may result from singlet fission. We compare two perylene diimide/pentacene charge transfer systems that differ only by triplet generation mechanism: SF versus intersystem crossing (ISC), sensitized by using a soluble lead phthalocyanine derivative. We use time-resolved microwave conductivity (TRMC) to measure the charge yield in each system and transient absorption (TA) to follow the triplet population dynamics. These experiments are described by a single global kinetic model, with most of its parameters fixed via control experiments. While we observe modest differences in the charge-transfer rate constants between each sample, 4–10× as a function of triplet generation mechanism, all samples remain far below the predicted diffusion-limited rate constant of 10 7 –10 8 s –1 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Diagnosing heterogeneous dynamics in single-molecule/particle trajectories with multiscale wavelets

In this study, we describe a simple automated method to extract and quantify transient heterogeneous dynamical changes from large data sets generated in single-molecule/particle tracking experiments. Based on wavelet transform, the method transforms raw data to locally match dynamics of interest. This is accomplished using statistically adaptive universal thresholding, whose advantage is to avoid a single arbitrary threshold that might conceal individual variability across populations. How to implement this multiscale method is described, focusing on local confined diffusion separated by transient transport periods or hopping events, with three specific examples: in cell biology, biotechnology, and glassy colloid dynamics. The discussion is generalized within the framework of continuous time random walk. This computationally efficient method can run routinely on hundreds of millions of data points analyzed within an hour on a desktop personal computer.

36 MATERIALS SCIENCE↗

Arbitrarily high super-resolving phase measurements at telecommunication wavelengths

We present two experiments that achieve phase super-resolution at telecommunication wavelengths. One of the experiments is realized in the space domain and the other is realized in the time domain. Both experiments show high visibility and are performed with standard lasers and single-photon detectors. The first experiment uses six-photon coincidences, whereas the latter experiment needs no coincidence measurements, is easy to perform, and achieves, in principle, arbitrarily high phase super-resolution. Here, we demonstrate a 30-fold increase of the resolution. We stress that neither entanglement nor joint detection is needed in these experiments, which demonstrates that neither is necessary to achieve phase super-resolution.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗