SEARCH · Engineering Papers

Results for “reference models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Demand-Side Grid (dsgrid) TEMPO Light-Duty Vehicle Charging Profiles v2022

Simulated hourly electric vehicle charging profiles for light-duty household passenger vehicles in the contiguous United States, 2018-2050. Profiles are differentiated by scenario, county, household and vehicle types, and charging type. Data was produced in 2022 using the Transportation Energy & Mobility Pathway Options (TEMPO) model and published in demand-side grid (dsgrid) toolkit format. Data are available for three adoption scenarios: "AEO Reference Case", which is aligned with the U.S. EIA Annual Energy Outlook 2018 (linked below), "EFS High Electrification", which is aligned with the High Electrification scenario of the Electrification Futures Study (linked below), and "All EV Sales by 2035", which assumes that average passenger light-duty EV sales reach 50% in 2030 and 100% in 2035. The charging shapes are derived from two key assumptions of which data users should be aware: "ubiquitous charger access", meaning that drivers of vehicles are assumed to have access to a charger whenever a trip is not in progress, and "immediate charging", meaning that immediately after trip completion, vehicles are plugged in and charge until they are either fully recharged or taken on another trip. These assumptions result in a bounding case in which vehicles' state of charge is maximized at all times. This bounding case would minimize range anxiety, but is unrealistic from the point of view of both electric vehicle service equipment (EVSE) (i.e., charger) access, and plug-in behavior as it can result in dozens of charging sessions per week for battery electric vehicles (BEVs) that in reality are often only plugged in a few times per week.

Array↗

DOE OSTI2025

Operation of helium sub-atmospheric multistage cryogenic centrifugal compressor trains: Part 2 – Transient modeling and pump-down path selection

Low-pressure conditions required for operation of helium cryogenic systems below the normal boiling point (i.e. 4.2 K) are established through a transient process, commonly referred to as ‘pump-down’. This process is defined as the transition from pressures above atmospheric conditions to the saturation pressure which corresponds to a specified operational temperature. The FRIB 2 K system consists of five cryogenic centrifugal compressors which are operated in series. Historically, the pump-down process path has been established through empirical methods and system operator experience. Investigation into the pump-down process at FRIB aimed to develop a pump-down methodology which relies on theoretical model predictions rather than empirically developed process paths. Ensuring stable operation during the pump-down process involved application of a centrifugal compressor performance prediction model, which is described in Part 1 of this paper. Compressor performance maps can be directly used to evaluate the stability of a selected pump-down path and anticipate the overall reliability of the selected path. In conjunction with the compressor performance maps, a system pressure model was developed to estimate the transient pressure response during the pump-down process. Lastly, an explicit equation was developed to establish a mass flow rate profile for the pump-down process. Implementation of the presented methodology (including the developed models) allows for the system operator to determine a continuous pump-down path which maintains compressor stability while conforming to overall system capabilities. Altogether, the methodology presented has resulted in simplification of transient pump-down operations and increased the reliability, stability and efficiency of the pump-down process.

Compressor train control↗

DOE OSTI2026

Evaluation of RMI Ejecta Sourcing from Reconstructed Interfaces in 2D FLAG Flyer-Plate Simulations

This study investigates the performance of RMI ejecta sourcing from a reconstructed interface in two-dimensional FLAG ejecta flyer-plate simulations. Enabling the RMI ejecta model to operate on reconstructed interfaces has been a longstanding challenge in FLAG, limiting its applicability to experiments in which interface reconstruction is not required. Addressing this limitation is therefore an important step toward expanding the model’s predictive capability. The first phase of this effort focused on identifying a flyer-plate/target configuration that produces large ejecta clouds from two distinct shocks using the standard RMI ejecta model. A series of simulations examined the effects of flyer composition, layer thickness, and mesh resolution on shock structure and ejecta formation. VISAR traces were used to evaluate shock timing and identify configurations that produced a clear double-shock response. A copper middle-layer flyer with a doubled tin layer yielded the most favorable shock characteristics and was selected as the baseline configuration. After confirming this configuration performed as expected when running a reference FLAG version, it became the basis for three simulations: (1) a standard two-dimensional ejecta flyer-plate calculation using a reference FLAG version, (2) the same calculation with the reconstructed interface option enabled, and (3) a calculation employing ALE strategies to force the ejecta model to operate on the reconstructed interface. While the baseline simulation produced the expected ejecta response, the reconstructed interface approach did not result in measurable ejecta, indicating that this capability remains under development. These results highlight both the progress made and the remaining challenges in extending the RMI ejecta model to reconstructed interfaces.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Selective consolidation of learning and memory via recall-gated plasticity

In a variety of species and behavioral contexts, learning and memory formation recruits two neural systems, with initial plasticity in one system being consolidated into the other over time. Moreover, consolidation is known to be selective; that is, some experiences are more likely to be consolidated into long-term memory than others. Here, we propose and analyze a model that captures common computational principles underlying such phenomena. The key component of this model is a mechanism by which a long-term learning and memory system prioritizes the storage of synaptic changes that are consistent with prior updates to the short-term system. This mechanism, which we refer to as recall-gated consolidation, has the effect of shielding long-term memory from spurious synaptic changes, enabling it to focus on reliable signals in the environment. We describe neural circuit implementations of this model for different types of learning problems, including supervised learning, reinforcement learning, and autoassociative memory storage. These implementations involve synaptic plasticity rules modulated by factors such as prediction accuracy, decision confidence, or familiarity. We then develop an analytical theory of the learning and memory performance of the model, in comparison to alternatives relying only on synapse-local consolidation mechanisms. We find that recall-gated consolidation provides significant advantages, substantially amplifying the signal-to-noise ratio with which memories can be stored in noisy environments. We show that recall-gated consolidation gives rise to a number of phenomena that are present in behavioral learning paradigms, including spaced learning effects, task-dependent rates of consolidation, and differing neural representations in short- and long-term pathways.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2024

Selective consolidation of learning and memory via recall-gated plasticity

Lindsey, Jack W. (ORCID:0000000309307327)↗

DOE OSTI2024

Consequences of plane-strain and plane-stress assumptions in fully coupled chemo-mechanical Li-ion battery models

In Li-ion battery research, it is common to simulate chemo-mechanical phenomena in reduced dimensions (e.g., 2-D) as opposed to fully resolve these complex physics in 3-D. It is common to assume either (1) the out-of-plane strain is negligible (commonly referred to as plane-strain), or (2) the out-of-plane stress is negligible (commonly referred to as plane-stress). However, there is typically little consideration as to the quantitative consequences of these approximations. Furthermore, the influence of these out-of-plane assumptions can be compounded and convoluted when chemo-mechanics models implement so-called “fully coupled” formulations, where the local species concentrations influence the stress-state and the stress-state influences the local species fluxes. Here, the present manuscript explores the implications of using plane-stress and plane-strain assumptions in 2-D as compared to simulating a full 3-D electrode particle. This comparative study includes simulating both isotropic and anisotropic particle intercalation where the particles can be surrounded by either a liquid or solid electrolyte. Additionally, common Li-ion battery-model metrics such as the state-of-stress, intercalation fraction distribution, and specific capacity are compared, while also considering the effects of particle size and C-rate. As alternatives to the pure plane-strain and plane stress approximations, two modified plane-strain assumptions are found to better approximate the fully coupled chemo-mechanical 3-D behavior.

25 ENERGY STORAGE↗

DOE OSTI2020

Validation of finite-element models using full-field experimental data: Levelling finite-element analysis data through a digital image correlation engine

Full-field data from digital image correlation (DIC) provide rich information for finite-element analysis (FEA) validation. However, there are several inherent inconsistencies between FEA and DIC data that must be rectified before meaningful, quantitative comparisons can be made, including strain formulations, coordinate systems, data locations, strain calculation algorithms, spatial resolutions and data filtering. As such, in this paper, we investigate two full-field validation approaches: (1) the direct interpolation approach, which addresses the first three inconsistencies by interpolating the quantity of interest from one mesh to the other, and (2) the proposed DIC-levelling approach, which addresses all six inconsistencies simultaneously by processing the FEA data through a stereo-DIC simulator to ‘level’ the FEA data to the DIC data in a regularisation sense. Synthetic ‘experimental’ DIC data were generated based on a reference FEA of an exemplar test specimen. The direct interpolation approach was applied, and significant strain errorswere computed, even though therewas no model form error, because the filtering effect of theDIC enginewas neglected. In contrast, the levelling approach provided accurate validation results, with no strain error when no model form error was present. Next, model form error was purposefully introduced via a mismatch of boundary conditions. With the direct interpolation approach, the mismatch in boundary conditions was completely obfuscated, while with the levelling approach, it was clearly observed. Finally, the ‘experimental’ DIC datawere purposefully misaligned slightly fromthe FEA data. Both validation techniques suffered from the misalignment, thus motivating continued efforts to develop a robust alignment process. In conclusion, direct interpolation is insufficient, and the proposed levelling approach is required to ensure that the FEA and the DIC data have the same spatial resolution and data filtering. Only after the FEA data have been ‘levelled’ to the DIC data can meaningful, quantitative error maps be computed.

42 ENGINEERING↗

DOE OSTI2020

Modeling thin layers of analytes on substrates for spectral analysis: use of solid/liquid n and k values to model reflectance spectra

Since solids are only sometimes seen en masse in a pure bulk form, and for liquids other than water almost never, a capability to model reflectance spectra from analytes deposited on various substrates would be highly advantageous. If available, the real, n ( ν ) , and imaginary, k ( ν ) , components of the complex refractive index, n n + i k , can be used to simulate infrared spectra, accounting for reflection, refraction, and absorption phenomena as a function of wavelength. We focus on using the Pacific Northwest National Laboratory (PNNL) derived n / k vectors for solid and liquid analytes deposited as thin layers on different types of substrates including conductors, such as aluminum, and inorganic dielectrics, such as glass. The model is an adaptation of the Monte Carlo ray trace modeling program, TracePro, extended through the use of its macrolanguage. The model is tested using thin films of organic liquids including silicone oil and no. 2 diesel fuel, as well as organic solids such as caffeine and acetaminophen on aluminum and glass. The predicted spectra for the solid films were compared to experimental hemispherical reflectance data measured using a Fourier transform spectrometer with an integrating sphere. The thickness of the calculated layer is a parameter for predicting the (transflectance) spectra and is obtained using the areal density measured from gravimetric methods to generate the thin-layer samples. Comparison of the calculated spectra with experimental hemispherical reflectance data shows excellent agreement, indicating promise for the use of measured n / k data to synthesize reference spectral data. In particular, accounting for the inhomogeneity of the deposits greatly improved the match with experimental data. Finally, the theoretical modeling shows that for thicker layers (ca. 20 to 100 μm) of typical organics possessing moderately strong k values, the longwave infrared features are often saturated and better spectral contrast is obtained from the overtone/combination bands in the shortwave infrared.

42 ENGINEERING↗

DOE OSTI2025

Serpent - Bison - THM Preliminary Multiphysics Modeling of a Nuclear Thermal Propulsion System Fuel Assembly

This work demonstrates the Monte Carlo neutronic and Thermo-Hydraulic coupling scheme using the Serpent code and MOOSE application Bison and Thermo Hydraulic Module. The coupling scheme is then applied to the reference BWX Technologies Nuclear Ther- mal Propulsion system at he fuel assembly level where it’s used to perform an analysis of the isothermal material coefficients and potential material reactivity worth. A method is developed to isolate which feedback effects should be considered for proceeding with reduced order deterministic neutronic modeling where branch off analysis must be con- ducted. The convergence behavior of the coupling scheme is demonstrated where it fol- lows the standard Picard iteration approach. Verification studies for the method of deduc- ing relevant feedback effects is also demonstrated.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

Modelling Nuclear Thermal Propulsion Reactor Expander Cycle Startup Transients

As the interest in nuclear thermal propulsion grows, the need for high fidelity and comprehensive models of the system increases. An expander cycle model was developed using RELAP-7 for the thermal-hydraulic performance and Griffin to provide the power level using a point kinetics approximation, for a reference NTP system. The tank and pump are approximated using boundary conditions. Flow is split between the moderator cooling channels flow path and the regenerative cooling/reflector cooling channels flow path. The flow recombines before entering the turbine and the fuel cooling channels. The turbine pressure ratio is maintained at 1.44 using a PID controller. A startup transient was simulated and shows the capability of the model to run from low temperature and pressures to nominal conditions.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2023

Modelling Nuclear Thermal Propulsion Reactor Expander Cycle Startup Transients

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2020

Electricity Subsector Transmission Resilience Maturity Model (TRMM) User Guide

The electric transmission sector is facing a range of threats to its functionality that are either new, more severe than experienced in earlier years, or more well understood. Such threats include more frequent and more severe extreme weather events, wildfires, droughts, and human-caused physical and cyberattacks. They also include geological, electromagnetic, and biological events. The novelty or increasing severity of these threats creates a significant need for transmission owners to implement programs to prevent, prepare for, respond to, and recover from such incidents. The national and economic security of the United States depends on the reliable functioning of the Nation’s critical infrastructure in the face of such threats, and the transmission networks are essential components of that infrastructure. The Electricity Subsector Transmission Resilience Maturity Model (TRMM) is a tool that a transmission organization can use to objectively evaluate and benchmark its currently established transmission resilience strategies, programs, policies, and investments, in order to target and prioritize enhancements where needed. The TRMM was developed to address the unique characteristics of the transmission system. The model can enable users to: • evaluate and benchmark their organization’s resilience capabilities, effectively and consistently • prioritize actions and investments to improve the resilience of their systems • share transmission-related knowledge, best practices, and relevant references within their organization and with business partners as a means to improve resilience capabilities • contribute to increasing the overall resilience of the Nation’s transmission systems. The TRMM provides descriptive rather than prescriptive industry-focused guidance. The model content is presented at a high level of abstraction so that it can be interpreted by transmission organizations of various types, structures, and sizes. The model is designed to an be easy-to-use, self-assessment tool.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2025

Comparison of removal and spatial mark‐resight models for estimating wild pig density

Density estimation is critical to effectively manage invasive species and elucidate areas of highest concern. For wild pigs (Sus scrofa), the ability to estimate density is complicated because of their variable home range sizes and social structure. Common methods for estimating density (e.g., mark-recapture) may be unsuitable in management applications because additional data needs to be collected before and after management. Removal models offer a suitable alternative to estimate density changes following management and can be applied broadly across areas where management of wild pigs is ongoing. We collected wild pig removal and camera trap data from 25 private properties ranging in size from approximately 0.5 km 2 to 95 km 2 across 3 ecoregions in South Carolina, USA, from 2020–2023. We compared factors affecting consistency and precision of property-level density estimates between removal and spatial mark-resight (SMR) models. In general, excluding 1 large outlier, density estimates from removal models were between 0.60 and 15.85 wild pigs/km 2 (median = 5.34) with a median coefficient of variation (CV) of 0.76 and 95% confidence intervals for the CV between 0.70 and 0.94. Similarly, excluding 1 large outlier, density estimates from SMR were between 0.22 and 30.97 wild pigs/km 2 (median = 5.48) with a median CV of 0.39 and 95% confidence intervals for the CV between 0.38 and 1.20. We found the precision of removal models was affected primarily by the number of wild pigs dispatched in the removal period (3 months) and the ecoregion in which they were removed. None of the covariates, including the number of recaptures (a corresponding measure of sample size), influenced precision of the SMR models, although recaptures did influence the density estimates. At the individual property level, density estimates from our 2 estimators were dissimilar from each other in approximately 80% of instances, although none of the covariates we examined influenced dissimilarity. Our results provide unique insight into how sample size affects density estimates using 2 common methods and into novel SMR models that incorporate both marked and unmarked detections. In addition, the density estimates in this study can be used as a reference for wild pig densities in common land cover types throughout the southeastern United States.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

Accelerated basis adaptation in homogeneous chaos spaces

Polynomial chaos expansions (PCE) provide an efficient approach to uncertainty quantification (UQ) and have been adapted to diverse applications across the spectrum of science and engineering. For situations involving large stochastic parameterizations, the curse of dimensionality renders PCE-based methods computationally prohibitive. A basis adaptation approach for PCE was proposed by Tipireddy and Ghanem (2014) which transforms the input random variables through an isometry such that sufficient probabilistic characterization of specific quantities of interest (QoI) is concentrated in an algebraic manifold embedded in the linear span of the dominant transformed variables. While quite versatile, that original version of the PCE basis adaptation exhibited slow convergence for a number of problems of practical significance. In the present paper, we propose two novel methods to accelerate the convergence of the original basis adaptation approach, thus expanding its reach while also providing insight into its performance. In the first method, information gained from a pilot PCE representation is used to correct the mean and Gaussian coefficients in the adapted space. By taking advantages of probabilistic information in higher dimensional adaptation gleaned from an initial adaptation, the second method updates the rotation matrix used to identify the dominant transformed variables. In this manner, the new rotation matrix concentrates even more probabilistic information in its first few dimensions. These two method can be combined to achieve even better performance, the combined method is referred to as sequentially optimized adaptation method. Here, the methods are demonstrated on an analytical test function and a model of a space structure with several sub-components and a non-smooth quantity of interest representing the maximum acceleration over time. Both methods achieve accelerated convergence of the basis adaptation approach with negligible additional costs.

Accelerated convergence↗

DOE OSTI2026

Finite-element boundary-integral simulation of thin wires and inhomogeneous penetrable bodies in subsurface multilayered anisotropic media

With the prevailing presence of drilling wells near the subsurface in mature oil and gas fields, the application of electromagnetic methods can be particularly challenging where the electromagnetic field is affected by the steel casing. In the past decades, borehole-to-surface and crosswell electromagnetic methods have been utilized for monitoring of reservoir and underground CO 2 storage. This paper presents a unified finite-element boundary-integral (FEBI) method capable of simultaneously modeling the complex electromagnetic interactions between thin metallic wires (representing steel casings) with 3D trajectory and arbitrary 3D inhomogeneous penetrable bodies (such as CO 2 plumes or hydrocarbon reservoirs) within anisotropic multilayered subsurface environments. Unlike existing approaches that treat these components separately or require dense discretization, or are limited to vertical wells, our unified formulation preserves flexible electromagnetic coupling while delivering improved computational efficiency. Assuming the background formation is multilayered anisotropic media, the surface integral equation method is applied to model the thin wires and boundaries of the inhomogeneous bodies. Meanwhile, the finite element method is applied to model the volume of inhomogeneous bodies. Here, the performance of the proposed FEBI method is assessed through comparison with reference numerical results and its practical significance is demonstrated through CO 2 plume monitoring scenarios.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

Habitat quality influences trade-offs in animal movement along the exploration–exploitation continuum

Abstract To successfully establish itself in a novel environment, an animal must make an inherent trade-off between knowledge accumulation and exploitation of knowledge gained (i.e., the exploration–exploitation dilemma). To evaluate how habitat quality affects the spatio-temporal scale of switching between exploration and exploitation during home range establishment, we conducted experimental trials comparing resource selection and space-use of translocated animals to those of reference individuals using reciprocal translocations between habitat types of differing quality. We selected wild pigs ( Sus scrofa ) as a model species to investigate hypotheses related to the movement behavior of translocated individuals because they are globally distributed large mammals that are often translocated within their introduced range to facilitate recreational hunting. Individuals translocated to higher quality habitat (i.e. higher proportions of bottomland hardwood habitats) exhibited smaller exploratory movements and began exploiting resources more quickly than those introduced to lower quality areas, although those in lower-quality areas demonstrated an increased rate of selection for preferred habitat as they gained knowledge of the landscape. Our data demonstrate that habitat quality mediates the spatial and temporal scale at which animals respond behaviorally to novel environments, and how these processes may determine the success of population establishment.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Understanding plasma turbulence through exact coherent structures

Plasma turbulence is a key challenge in understanding transport phenomena in magnetically confined plasmas. This work presents a generalized framework to analyze plasma turbulence that utilizes periodic orbit theory. In periodic orbit theory, doubly periodic solutions (coherent structures) of the governing equation(s) serve as building blocks of the considered turbulent dynamics. To illustrate the concept and method, the particularly simple Kuramoto–Sivashinsky (referred to here as LMRT for the original authors: LaQuey, Mahajan, Rutherford, and Tang) trapped-ion mode toy model is used. By applying numerical optimization techniques to the LMRT equation, we extract coherent spacetime patterns that represent the library of allowable fundamental structures of the equation. These structures provide a framework to systematically describe turbulence as a composition of recurrent solutions, revealing an underlying order within chaotic plasma motion. Although illustrated here using the simplified LMRT model for clarity, this framework provides a general strategy that can be extended to more complex and realistic models of plasma turbulence, including gyrokinetic systems. This offers a new method for predicting and potentially controlling transport processes in fusion plasmas by providing a bridge between nonlinear dynamical systems theory and plasma physics in the form of a generalized framework with which to analyze and understand spatially extended nonlinear partial differential equations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Detection of Synchrophasor False Data Injection Attack using Feature Interactive Network

The synchrophasor data recorded by Phasor Measurement Units (PMUs) plays an increasingly critical role in the regulation and situational awareness of power systems. However, the widely installed PMUs are vulnerable to multiple malicious attacks from cyber hackers during data transmission and storage. To address this problem, a Modified Ensemble Empirical Mode Decomposition (MEEMD) is proposed first to extract the intrinsic mode functions of each Synchrophasor Data Attacks (SDA). The frequency-based adaptive screening criterion embedded in MEEMD is used to eliminate the false intrinsic mode functions. Next, a Multivariate Convolutional Neural Network (MCNN) is proposed to identify multiple SDA by utilizing the extracted intrinsic mode functions and original SDA as input vectors. A fusion block as the main structure of MCNN is also leveraged to increase the diversity of features and compress the model parameters. Integrating MEEMD and MCNN, a framework with automatic feature extraction and multi-source information fusion capability, referred to as Feature Interactive Network (FIN), is proposed to detect multiple SDA. Based on the proposed FIN framework, six types of SDA are explored for the first time using actual synchrophasor data in FNET/Grideye that was collected from different locations in the U.S. Eastern Interconnection. Finally, a large quantity of experiments with different attack strengths are used to evaluate the adaptability and classification performance of the proposed FIN.

24 POWER TRANSMISSION AND DISTRIBUTION↗