Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “quality control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Confirmatory LBL Analysis of AGR-5/6/7 Compacts and Over-Coated Particles BWXT Batches 11034, 14154C, 14156C, AND 14156D

Fuel for the Advanced Gas Reactor Fuel Development and Qualification (AGR) Program’s AGR-5/6/7 irradiation test in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR) was produced by BWX Technologies (BWXT) Nuclear Operations Group in Lynchburg, Virginia. Tristructural isotropic (TRISO) coatings were deposited using a 150-mm-diameter production-scale fluidized-bed chemical vapor deposition (CVD) furnace on 425-μm-nominal-diameter spherical kernels from Lot J52R-16-69317 containing a mixture of 15.5% 235U low-enriched uranium carbide and uranium oxide (UCO). The TRISO coatings consisted of four consecutive CVD layers: a ~50% dense carbon buffer layer with 100-μmnominal thickness, a dense inner pyrolytic carbon (IPyC) layer with 40-μm-nominal thickness, a silicon carbide (SiC) layer with 35-μm-nominal thickness, and a dense outer pyrolytic carbon (OPyC) layer with 40-μm-nominal thickness. TRISO-coated particle Lot J52R-16-98005 was over-coated with a graphite/resin blend and these over-coated particles were pressed in half-inch-diameter, one-inch-long cylindrical compacts. Two packing fractions (PF) were produced, 40%PF and 25%PF, where the TRISO particle volume made up approximately 40% and 25% of the total compact volume, respectively. The AGR-5/6/7 Fuel Specification, SPC-1352 [Marshall 2016], provides the requirements necessary for acceptance of the fuel manufactured for the AGR-5/6/7 irradiation test. Quality control (QC) acceptance testing for all AGR-5/6/7 composited lots and single batches was performed by BWXT, with the exception of pyrolytic carbon (PyC) anisotropy and defective IPyC fraction in the TRISO candidate batches and final composite, which were measured at the Oak Ridge National Laboratory (ORNL) and reported in ORNL/TM-2017/036 [Hunn et al. 2017] and ORNL/TM-2017/037 [Helmreich et al. 2017a].

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assessing the Wind Energy Potential in Bangladesh: Enabling Wind Energy Development with Data Products

USAID Bangladesh and the U.S. Department of Energy’s National Renewable Energy Laboratory partnered with the Government of Bangladesh to develop a national wind resource assessment. The assessment used sophisticated resource modeling that was validated by a ground measurement campaign. Results from the project included a long-term, correlated wind data set; validated high-resolution wind resource maps; and publicly available data accessible through the RE Data Explorer (https://www.re-explorer.org/). The Renewable Energy (RE) Data Explorer allows users to access and download the Bangladesh wind resource assessment data and related geographic information system (GIS) data sets and perform customized technical potential analyses. Figure ES-1 is an example wind resource map for Bangladesh that can be created with the RE Data Explorer. This project improved upon existing global data sets by using best-in-class modeling techniques and analysis. Global models are good first steps in predicting wind resources in various parts of the world, but they do not generate the accuracy needed to reduce project risk and stimulate renewable investment. This project improved the quality of modeled wind resource data for Bangladesh. In addition to the modeling effort, the project team used a multi-year, local data-collection campaign to validate the model and further improve the accuracy of the data sets. The measurement campaign consisted of nine meteorological sites representing all geographical regions of the country. Seven meteorological towers and one remote-sensing, sonic detection and ranging unit (deployed at two sites) collected the data. Site-selection criteria focused on geographic diversity and proximity to existing transmission lines. Figure ES-1 shows measurement locations. The measurement campaign spanned June 2014 through December 2017. The results of the Bangladesh wind resource assessment will help Bangladesh overcome significant energy challenges. Its energy sector suffers from power shortages, increasing demand, decreasing domestic natural gas reserves, and inadequate transmission infrastructure. As part of a comprehensive plan to overcome these challenges, Bangladesh has committed that 10% of the total generation capacity will be renewable energy by 2021 (Power Division 2016). High-quality renewable energy resource data and other GIS data, such as those developed in this assessment, are important if Bangladesh wishes to reach its 10% renewable energy capacity target. These data support informed decision making, ranging from policy and investment decisions to reliable power sector planning. Specifically, the Bangladesh wind resource assessment will help reduce technical risk and encourage private-sector interest in the nascent wind market in Bangladesh. In addition, the Government of Bangladesh may use the results of the wind resource assessment to develop well-designed policies that could encourage investment in wind energy. This report provides a comprehensive description of the Bangladesh wind resource assessment, including details on the modeling approach and methods, instrumentation, data quality-control techniques, and resulting data sets.

17 WIND ENERGY↗

Scalable processing of ZnS nanoparticles for high photoluminescence efficiency quantum dots

Nano Elements Source, LLC, a biotech startup has licensed the NanoFermentation technology from Oak Ridge National Laboratory to further commercialize low cost, cadmium free photoluminescent nanoparticles produced using affordable, environmentally-friendly. This project aimed to develop post chemical processing of biosynthesized ZnS quantum dots (QD) to improve their efficiency of luminescence to make them suitable for solid state lighting applications. Several post processing approached were proposed and tested using to biosynthesized of ZnS QD. Optical properties of ZnS nanoparticles including soft chemical etching, and photonic etching have been tested and quantified against standard materials. We applied the developed chemical modification approach to control quality of chemically synthetized ZnS QD’s, and to calculate the maximum achievable efficiency of photoluminescence. We estimated the cost of the proposed post-processing treatment of nanoFermented nanoparticles and proposed several approaches to further the development of low cost nanoparticles for electro-optical and other applications relevant to DOE mission.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Connecting AmeriFlux to the Globe, Extending the Partnership with Global Flux Network FLUXNET

We propose a project that will extend and expand the activities and contributions of AmeriFlux, to the global stage by working with our international partners to continue operating and expand the functioning of global FLUXNET database. One goal is to produce the next-generation FLUXNET dataset. This will be an integrated dataset on carbon, water and energy fluxes, on meteorological conditions and on the structure and function of the ecosystems; we have to potential to construct a new database, double the size of the La Thuile dataset, with over 2000 site-years of trace gas flux measurements, and supporting meteorological and site meta-data from over 400 sites world-wide. The production of the next FLUXNET database is critical to the activities of this ROSE’s solicitation because these data will drive many of the carbon cycle synthesis activities and the model parameterization and validation activities. A second goal is to build the next-generation, data-system that will house, distribute and query data and discover new information by the broader biogeoscience user community. The third goal is to use these data in synthesis activities that improve our understanding on how climate, weather, ecological, physiological and soil factors govern the exchange of carbon, water and energy between vegetation and the atmosphere at multiple time and space scales. The fourth goal is to act as a coordinator of the project to recruit data, to organize a workshop/conference and to build a community of data sharing and interaction across vast cultural spectrum of participating scientists. The rationale for proposing this work is based on the fact that the vast databases that are produced by flux networks cannot perpetuate and evolve without continued support of the intellectual activities of scientists who produce data, expert in databases, and scientists who use data for modeling. The actuality of a flux network takes human intervention to recruit data from different countries and cultures, to build trust to share data in open-access format, to support data users, and to collaborate. Specifically, we will develop an updated data portal that is easy to navigate and conducive for distributing, visualization, evaluation and discovery of the multiple types of flux and environmental data and information. We will foster collaboration and interactions with our national and international partners and the recruitment of data by: 1) continuing the periodic publication of the newsletter, FLUXLETTER; 2) by hosting an international conference; 3) by coordinating and launching multi-investigator data synthesis activities; and 4) by developing tools that coordinate the development of research papers resulting from the dataset. Data products include raw and gap-filled data at their native time steps (30 minute averages), data products that are integrated on daily and annual time scales and value added products like ecosystem respiration and canopy photosynthesis. Uncertainty analysis and quality control metrics will be produced in coordination with AmeriFlux and ICOS. We will also work with colleagues to expand the scope of FLUXNET beyond carbon dioxide and water vapor, and start archiving the growing methane flux databases that are being collected, world-wide. The interpretation of the flux data relies on good meta-data. We will work with data providers to populate and expand the meta-data archives. We will also work with collaborators to incorporate data from remote sensing products such as MODIS and Landsat, from corresponding climate and weather stations. Another goal is to incorporate new data on canopy structure, with recent LIDAR acquisitions, to populate the data archive with automated soil respiration and understory flux measurements, where available and local climate records for corresponding sites. And, we will collaborate with the TRY database, by merging flux data with plant trait information.

54 ENVIRONMENTAL SCIENCES↗

Weatherization Crew Leader Job Task Analysis

The US Department of Energy's Guidelines for Home Energy Professionals project maintains job task analyses for jobs in the Weatherization Assistance Program and home performance industry. One of those jobs is Crew Leader, defined as: 'A Crew Leader is responsible for supervising and assisting in the retrofitting activities specified in the scope of work. He or she is responsible for interacting with the client plus managing personnel and materials on the job site in a safe and effective manner. The Crew Leader is responsible for quality control, testing procedures, documentation, and conducting a walk through in preparation that all work is completed in a satisfactory manner.' This document is an updated version of the Crew Leader job task analysis.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

National Wind Technology Center-Characterization of Atmospheric Conditions

Data provided by the instrumentation located at the National Wind Technology Center (NWTC) is compiled below for the purposes of characterizing the atmospheric operating conditions at the National Renewable Energy Laboratories (NREL) wind site. Conditions are presented conditioned on month of the year to show seasonal variation, and based on characteristic quantities seen in the atmospheric flow including, bulk wind speed, direction, and atmospheric stability. All data reported and analyzed in the following document were collected from instrumentation mounted on the 135 m-tall masts erected at the NWTC near Boulder, Colorado. Each of the two met-masts (named M4 and M5) were sited specifically to measure the inflow wind to several of the utility-scale turbines at the NWTC. The construction, operation, and maintenance of the masts has been supported since their commissioning in 2011 by the Department of Energy, Office of Energy Efficiency and Renewable Energy, Wind and Water Power Program. Data from the masts are publicly available for download or basic visualization, hosted on NREL's website (https://nwtc.nrel.gov/135mData). Data from the masts have been used in the past for a wide range of projects including wind turbine power performance measurements, high fidelity model development and validation, and atmospheric science research. An interactive visualization platform has been developed on NREL's Open Energy Information platform and can be used to reproduce many of the graphics included in the current work. This report describes in detail the atmospheric conditions recorded by M5, the inflow mast for the DOE-owned GE 1.5 MW wind turbine. The report focuses on data recorded from August 2012 to May 2018 and includes: an introduction to the wind climate at the NWTC; a physical description of the met masts; a review of installed instrumentation; and data collection, processing, and quality control methods. In addition to a concise description of the instrumentation from the met masts and the data channels they provide, this report characterizes the behavior of the atmospheric resource first in a cumulative sense, discussing mainly the distributions wind speeds, flow directions and thermodynamic properties at several heights along the towers. Periodicity in atmospheric conditions is then detailed through analysis of diurnal and annual cycles of the data streams. Periods of both low turbulence and extreme atmospheric events that are of interest in terms of wind turbine operation and wind energy research are detailed in the final chapter of this report. Low turbulence events are somewhat rare at the NWTC and are of interest from the perspective of validating the operation of new wind turbine and blade designs. Similarly, the NTWC is known for a relatively higher rate of occurrence of extreme weather events.

17 WIND ENERGY↗

Considerations for Application of Additive Manufacturing to Nuclear Reactor Core Components

The following chapter represents the current state of literature on the selected additive manufacturing technologies and was written with an emphasis on quality control and material performance repeatability. Research and standards published by government entities such as the National Institute of Standards and Technology (NIST) and Department of Energy (DOE) have been included where applicable. It is recommended that literature be reviewed, and new knowledge integrated no less frequently than every four years due to the rapid pace of advancements in additive manufacturing and associated industries. AM presents unique challenges in certification for NPP applications such as anisotropic material properties, porosity, underdeveloped process control feedback systems, and reproducibility. This chapter begins with an overview of the selected AM technologies, followed by a systematic review of literature to detail the fabrication process and difficulties with repeatably fabricating fully dense, geometrically accurate components with known material properties.

36 MATERIALS SCIENCE↗

Radiative Flux Analysis (RADFLUXANAL) Value-Added Product: Retrieval of Clear-Sky Broadband Radiative Fluxes and Other Derived Values

This technical report describes the algorithms used in the Radiative Flux Analysis (RADFLUXANAL) Value-Added Product (VAP). This VAP estimates clear sky broadband irradiance values and derives several additional cloud properties from broadband measurements including fractional sky cover and cloud optical depth. The VAP is based on a collection of algorithms and codes developed by Charles N. Long. It is an updated version of the Shortwave Flux Analysis VAP that has been used in ARM for a number of years. The RADFLUXANAL VAP includes two major updates over the previous Shortwave Flux Analysis VAP: 1) longwave (LW) clear sky irradiance estimates and derived parameters, and 2) takes in better quality-controlled input data from the QCRAD VAP.

54 ENVIRONMENTAL SCIENCES↗

$\beta-\gamma$ Absolute Calibration (Rev. 1)

Identification of nuclear events rely on accurate measurement of radioxenon releases. Measurement of radioxenon relies on accurately knowing the detection efficiency for each isotope. Four xenon isotopes are of interest: 135 Xe, 133 Xe, 133 mXe, and 131 mXe. Each isotope has a unique signature; however, there is overlap between each signature. A series of ratio terms, called interference ratios, helps account for the challenges created by the overlap. The ratio and detection efficiency terms are all determined during the initial detector calibration. Additional spectra are needed for a complete calibration: the radon daughter 214 Pb/ 214 Bi, the detector background, and the 137 Cs quality control (QC).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Protein Factory on a Chip for Rapid Therapeutics

The potential for new, re-emerging, or engineered pandemic threats could challenge our nation's biosecurity, requiring rapid and flexible countermeasure development platforms. In healthcare, one of the main hindrances to the timely development of protein-based therapeutics for cancer, infectious disease, and other diseases has been a slow and expensive quality-controlled production stage. We present a protein-based technology that has the potential to address these crucial problems in biosecurity and healthcare by maximizing protein production and system portability, while minimizing production latency and cost. Specifically, we have developed a reusable, portable first-generation platform that leverages the advantages of cell-free protein synthesis (CFPS) and flow cells to create practical amounts of clinically relevant therapeutics. We have demonstrated that this technology is reusable and programmable, enabling a single platform that can synthesize multiple dosages of various therapeutics and vaccine in the field. Implementing this technology could mitigate pandemic threats by providing a rapidly-deployable (just-in-time), versatile (precision medicine) production of biologic therapeutics to the infected patient’s locale (point-of-care). In drug development, once promising drug variations are identified, the platform can be scaled to quickly produce practical amounts of protein for patient testing in the matter of days (vs. months) at a fraction of the cost of existing technology.

59 BASIC BIOLOGICAL SCIENCES↗

Investigating Scientific Data Change with User Research Methods

Scientific datasets are continually expanding and changing due to fluctuations with instruments, quality assessment and quality control processes, and modifications to software pipelines. Datasets include minimal information about these changes or their effects requiring scientists manually assess modifications through a number of labor intensive and ad-hoc steps. The Deduce project is investigating data change to develop metrics, methods, and tools that will help scientists systematically identify and make decisions around data changes. Currently, there is a lack of understanding, and common practices, for identifying and evaluating changes in datasets since systematically measuring and managing data change is under explored in scientific work. We are conducting user research to address this need by exploring scientist's conceptualizations, behaviors, needs, and motivations when dealing with changing datasets. Our user research utilizes multiple methods to produce foundational, generative insights and evaluate research products produced by our team. In this paper, we detail our user research process and outline our findings about data change that emerge from our studies. Our work illustrates how scientific software teams can push beyond just usability testing user interfaces or tools to better probe the underlying ideas they are developing solutions to address.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

Identifying Suspect Instrument Intervals Using Midnight Noise Time Histories

With an intense work ethic, and high levels of devotion to their craft, seismologists continue to battle the elements and wrestle with complex logistics in their efforts to field instrumentation over the entire globe. We are fortunate to see data volumes accelerating in size, and quality continuing to improve; for example, universal timing issues can now be considered rare. However, instrument response issues are still common, and can hinder research that seeks to understand amplitudes of seismic wavefields. We are interested in using the accumulations of seismic data to develop models that will predict high frequency (0.2-20 Hz, and higher) signal amplitudes for explosion monitoring purposes over broad areas, which requires large data sets and extensive quality control. To identify response and station health issues, we have collected noise time histories for global seismic data, focusing on measurements near (but not restricted to) midnight to eliminate diurnal variations, and have manually determined time intervals that appear inconsistent with background behavior. We assign descriptive labels, but do not attempt to diagnose causes. We use these intervals to discard data. To date, we have examined 39,260 channels from 11,105 stations, heavily weighted toward IRIS holdings, dates through 2017 (depending on station, roughly the date we started our manual review), bands between 1 and 8 Hz, finding 24,733 anomalous time intervals. The great majority (90%) of these intervals appear to be shifts of constant offset, often bounded by times of known instrument changes, likely the result of poor documentation of response parameters at one of many stages between the field and the plotter. We hope these results can be of use to our colleagues, and would encourage community efforts to diagnose anomalous behavior, and fix poor responses. We also hope these results will support automation efforts, including application of supervised learning techniques.

47 OTHER INSTRUMENTATION↗

bifiPV2020 Bifacial Workshop: A Technology Overview

The virtual bifiPV Workshop was held in July 2020 to provide the solar industry with a forum for sharing and discussing research into bifacial photovoltaic (PV) technology. This report outlines major insights from the workshop to give the reader an overview of the latest developments in bifacial PV technology worldwide, from the lab to the field. Citations are drawn from this workshop unless otherwise noted, with all proceedings available online at bifipvworkshop. com. Presentations for the bifiPV2020 Workshop focused on the following areas: bifacial power plant modeling and simulation, albedo improvements, the development of encapsulants, the durability and reliability of current bifacial technologies, performance comparisons between glass-glass and glass-transparent backsheet configurations, the future of passivated emitter and rear contact (PERC) solar cells, and the growing adoption of n-type solar cells. With 650 GW total PV installed worldwide and 1 TW to come very soon, PERC is now the standard PV cell type produced en masse. However, it is already reaching 23% efficiency, the upper limit for this type of technology. PV modules breaking the 0.5-kW barrier are starting to appear, and the costs of standard PERC technology are already below 0.2 USD/Wp. In 2019, five GW of bifacial PV were installed worldwide. In 2020, the majority of bifacial installations are expected to be located in the United States, China, and Middle East and North Africa (MENA) states. N-type bifacial technologies are becoming increasingly viable and have huge potential to dominate the market in the coming years. With bifacial technology mounted on horizontal single-axis trackers (HSAT), bids below 10 USD/MWh will soon be observed in the MENA region, and later in Chile and the United States. Factory audits and reliability testing can reduce field failures by helping buyers to select producers that follow rigorous quality assurance and quality control processes.

14 SOLAR ENERGY↗

Detection of Defects in Additively Manufactured Metallic Materials with Machine Learning of Pulsed Thermography Images

Additive manufacturing (AM) is an emerging method for cost-efficient fabrication of nuclear reactor parts. AM of metallic structures for nuclear energy applications is currently based on laser powder bed fusion (LPBF) process, which can introduce internal material flaws, such as pores and anisotropy. Integrity of AM structures needs to be evaluated nondestructively because material flaws could lead to premature failures due to exposure to high temperature, radiation and corrosive environment in a nuclear reactor. Quality control (QC) requires nondestructive evaluation (NDE) of actual AM structures. Pulsed thermography is a potentially promising QC technique because it is scalable to arbitrary structure size. However, detection sensitivity of this method is limited by noises. We investigate separation of signal from noise in thermography images using several machine learning (ML) methods, including new spatio-temporal blind source separation (STBSS) and spatio-temporal sparse dictionary learning (STSDL) methods. Performance of the ML methods is benchmarked using thermography data obtained from imaging stainless steel 316L and Inconel 718 specimens produced LPBF method with imprinted calibrated porosity defects. The ML methods are ranked by F-score and execution runtime. The ML methods with higher accuracy require longer run time. However, this runtime is sufficiently short to perform QC within a realistic time frame.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

RELAP5-3D Modeling of High Temperature Test Facility (HTTF) Test PG-26

The High Temperature Test Facility (HTTF) at Oregon State University (OSU) is a scaled integral effects experiment designed to investigate transient behavior in high-temperature gas-cooled nuclear reactors with prismatic fuel and reflector blocks. Several tests have been completed, and more are still planned to at the HTTF, including depressurized conduction cooldown (DCC) and pressurized conduction cooldown (PCC) transients. This report analyses test PG-26, a progression of the Double Ended Inlet-Outlet Crossover Duct Break transient that is referred to as a DCC. PG-26 has been performed at the HTTF between May 30 and June 30, 2019. Core initial conditions (i.e., before the DCC started) have been met using low power (<100 kW) and two of ten available electric heaters. The DCC transient was initiated during the 50 th hour of the test. The break valves were opened, and hot helium from the core and cold helium from the reactor cavity simulation tank (RCST) started mixing. The gases flowed in a countercurrent fashion, where the top half of the hot duct contained hot helium that flowed in one direction and cold helium that flowed in the other direction in the bottom half of the duct. After the pressure and density reached equilibrium, the event entered a diffusion mode. The onset of a reverse natural circulation was not observed during the DCC period of the test. Version 4.4.2ie of the RELAP5-3D computer code has been used to model the HTTF PG-26 test, and results have been compared to available high-quality measured data. The model used in this study is the quality-controlled HTTF RELAP5-3D model (HTTF base 2018-04-19 QA), originally developed by P. Bayless. The report includes RELAP5-3D results of the “base calculations” as well as some sensitivities to important uncertain model inputs, such as primary helium mass flow rate, core ceramic thermal properties, as well as heat evacuation and loop friction models. Using the base RELAP5-3D model predicts a countercurrent helium flow in the hot duct observed at the beginning of the DCC, but instead of going into a molecular diffusion mode, the model predicts the onset of natural convection. Increasing friction in the core and hot duct prevents the natural convection from happening in some of the simulations. Although some temperatures are well predicted (and even overpredicted), the general tendency is to underpredict the ceramic and helium temperatures and heat removal rates during the DCC, resulting in many of the assessment findings being in minimal or insufficient agreement with the data. It is worth noting that the described discrepancies between measured data and RELAP5-3D predictions are not RELAP5-3D code limitations. More so, they reflect limitations in boundary condition and thermal property knowledge. While the RELAP5-3D calculations of the test provide some insights into what happens during the transient, and point to missing or potentially uncertain data to which the experimenters can direct their attention, the principal conclusion is that the PG-26 test data are insufficient for a system code assessment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Scale-Up of Electrode Coating and Flow-Field for Commercial Hydrogen Peroxide Electrolyzer: Cooperative Research and Development Final Report, CRADA Number CRD-17-00687

Hydrogen peroxide is currently produced at central chemical plants via the anthraquinone oxidation process. This process produces environmental pollutants that are costly to remediate, requires hazardous long distance shipping of highly concentrated peroxide (50% or 70%), and necessitates extra handling costs related to storage and dilution. Peroxygen Systems, Inc. (PSi) is developing breakthrough technology for on-site hydrogen peroxide production. PSi’s on-site on-demand electrolyzer can reduce the cost of producing hydrogen peroxide by 50%, while also completely eliminating the cost and safety issues associated with shipping and handling of high concentration hydrogen peroxide. The challenge for PSi is scaling. To support the next step toward commercialization (customer pilot tests), scaling the prototype into larger single cells and 20-40 cell stacks is required. In addition to internal hardware and flow-field design efforts at PSi, NREL will address three critical problems for this scale-up effort: (1) demonstrating a large scale roll-to-roll (R2R) process to coat uniform electrode materials for 100 cm2 and 500 cm2 stack testing, (2) demonstrating an in-line diagnostic to achieve better electrode quality control, and (3) performing in situ cell/stack testing to better understand and optimize the performance of the flow field design.

28 EE - Advanced Manufacturing Office (EE-5A)↗

Inkjet Printing to Scale Perovskite and Silicon Tandem Solar Cell: Cooperative Research and Development Final Report, CRADA Number CRD-17-00690

The proposed project seeks to develop a method for inkjet printing of the active layer in perovskite solar cells for application in stand-alone products or added to conventional silicon solar cells in a mechanically-stacked tandem configuration. This technology presents significant advanced manufacturing challenges and opportunities in getting to scale, including development of novel uses for printing technologies and development of predictive quality control techniques.

14 SOLAR ENERGY↗

bifiPV2020 Bifacial Workshop: A Technology Overview

The virtual bifiPV Workshop was held in July 2020 to provide the solar industry with a forum for sharing and discussing research into bifacial photovoltaic (PV) technology. This report outlines major insights from the workshop to give the reader an overview of the latest developments in bifacial PV technology worldwide, from the lab to the field. Citations are drawn from this workshop unless otherwise noted. Presentations for the bifiPV2020 Workshop focused on the following areas: bifacial power plant modeling and simulation, albedo improvements, the development of encapsulants, the durability and reliability of current bifacial technologies, performance comparisons between glass-glass and glass-transparent backsheet configurations, the future of passivated emitter and rear contact (PERC) solar cells, and the growing adoption of n-type solar cells. With 650 GW total PV installed worldwide and 1 TW to come very soon, PERC is now the standard PV cell type produced en masse. However, it is already reaching 23% efficiency, the upper limit for this type of technology. PV modules breaking the 0.5-kW barrier are starting to appear, and the costs of standard PERC technology are already below 0.2 USD/Wp. In 2019, five GW of bifacial PV were installed worldwide. In 2020, the majority of bifacial installations are expected to be located in the United States, China, and Middle East and North Africa (MENA) states. N-type bifacial technologies are becoming increasingly viable and have huge potential to dominate the market in the coming years. With bifacial technology mounted on horizontal single-axis trackers (HSAT), bids below 10 USD/MWh will soon be observed in the MENA region, and later in Chile and the United States. Factory audits and reliability testing can reduce field failures by helping buyers to select producers that follow rigorous quality assurance and quality control processes.

14 SOLAR ENERGY↗