Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parallel systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

An electrochemical study of corrosion protection by primer-topcoat systems on 4130 steel with ac impedance and dc methods

To investigate metal surface corrosion and the breakdown of metal protective coatings, the ac impedance method is applied to six systems of primer coated and primer topcoated 4130 steel. Two primers were used: a zinc-rich epoxy primer and a red lead oxide epoxy primer. The epoxy-polyamine topcoat was used in four of the systems. The EG and G-PARC Model 368 ac impedance measurement system, along with dc measurements with the same system using the polarization resistance method, were used to monitor changing properties of coated 4230 steel disks immersed in 3.5 percent NaCl solutions buffered at pH 5.4 over periods of 40 to 60 days. The corrosion system can be represented by an electronic analog called an equivalent circuit consisting of resistors and capacitors in specific arrangements. This equivalent circuit parallels the impedance behavior of the corrosion system during a frequency scan. Values for the resistors and capacitors, that can be assigned in the equivalent circuit following a least-squares analysis of the data, describe changes that occur on the corroding metal surface and in the protective coatings. Two equivalent circuits have been determined that predict the correct Bode phase and magnitude of the experimental sample at different immersion times. The dc corrosion current density data are related to equivalent circuit element parameters. Methods for determining corrosion rate with ac impedance parameters are verified by the dc method.

Mendrek, M. J.↗
NASA NTRS1979

The crew activity planning system bus interface unit

The hardware and software designs used to implement a high speed parallel communications interface to the MITRE 307.2 kilobit/second serial bus communications system are described. The primary topic is the development of the bus interface unit.

Allen, M. A.↗
DOE OSTI2023

Multigrid Reduction in Time for Chaotic Dynamical Systems

As CPU clock speeds have stagnated and high performance computers continue to have ever higher core counts, increased parallelism is needed to take advantage of these new architectures. Traditional serial time-marching schemes can be a significant bottleneck, as many types of simulations require large numbers of time-steps which must be computed sequentially. Parallel-in-time schemes, such as the Multigrid Reduction in Time (MGRIT) method, remedy this by parallelizing across time-steps and have shown promising results for parabolic problems. However, chaotic problems have proved more difficult, since chaotic initial value problems (IVPs) are inherently ill-conditioned. MGRIT relies on a hierarchy of successively coarser time-grids to iteratively correct the solution on the finest time-grid, but due to the nature of chaotic systems, small inaccuracies on the coarser levels can be greatly magnified and lead to poor coarse-grid corrections. Here we introduce a modified MGRIT algorithm based on an existing quadratically converging nonlinear extension to the multigrid Full Approximation Scheme (FAS), as well as a novel time-coarsening scheme. Together, these approaches better capture long-term chaotic behavior on coarse-grids and greatly improve convergence of MGRIT for chaotic IVPs. Further, we introduce a novel low-memory variant of the algorithm for solving chaotic PDEs with MGRIT which not only solves the IVP, but also provides estimates for the unstable Lyapunov vectors of the system. Finally, we provide supporting numerical results for the Lorenz system and demonstrate parallel speedup for the chaotic Kuramoto–Sivashinsky PDE over a significantly longer time-domain than in previous works.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1984

Automation effects in a stereotypical multiloop manual control system

The increasing reliance of state-of-the art, high performance aircraft on high authority stability and command augmentation systems, in order to obtain satisfactory performance and handling qualities, has made critical the achievement of a better understanding of human capabilities, limitations, and preferences during interactions with complex dynamic systems that involve task allocation between man and machine. An analytical and experimental study has been undertaken to investigate human interaction with a simple, multiloop dynamic system in which human activity was systematically varied by changing the levels of automation. Task definition has led to a control loop structure which parallels that for any multiloop manual control system, and may therefore be considered a stereotype.

Hess, R. A.↗
NASA NTRS1986

Development of AC impedance methods for evaluating corroding metal surfaces and coatings

In an effort to investigate metal surface corrosion and the breakdown of metal protective coatings the AC Impedance Method was applied to zinc chromate primer coated 2219-T87 aluminum. The model 368-1 AC Impedance Measurement System recently acquired by the MSFC Corrosion Research Branch was used to monitor changing properties of coated aluminum disks immersed in 3.5% NaCl buffered at ph 5.5 over three to four weeks. The DC polarization resistance runs were performed on the same samples. The corrosion system can be represented by an electronic analog called an equivalent circuit that consists of transistors and capacitors in specific arrangements. This equivalent circuit parallels the impedance behavior of the corrosion system during a frequency scan. Values for resistances and capacities that can be assigned in the equivalent circuit following a least squares analysis of the data describe changes that occur on the corroding metal surface and in the protective coating. A suitable equivalent circuit was determined that predicts the correct Bode phase and magnitude for the experimental sample. The DC corrosion current density data are related to equivalent circuit element parameters.

Knockemus, Ward↗
NASA NTRS1989

Experimenting With Multiprocessor Simulator Concepts

Multiple microcomputer system used to investigate application of parallel processing to real-time simulation. With dual-base architecture, each microcomputer communicates with corresponding microcomputer on opposite bus through dual-port interface memory. Transfers of data to and from front-end processor occur on interactive information bus. Transfers of data related to simulation calculations occur on real-time-information bus. System, called the real-time multiprocessor simulator (RTMPS), is tool for developing low-cost, portable, user-friendly simulators.

Blech, Richard A.↗
NASA NTRS1989

Parallel processing techniques for finite element analysis of nonlinear large truss structures

Methods were developed for parallel processing of finite element solutions of large truss structures. The parallel processing techniques were implemented in two stages, i.e., the repeated forming of the nonlinear global stiffness matrix and the solving of the global system of equations. The Sequent Balance 21000 parallel computer was employed to demonstrate the procedures and the speed-up.

Chien, L. S.↗
NASA NTRS1994

Does human cognition allow Human Factors (HF) certification of advanced aircrew systems?

This paper has examined the requirements of HF specification and certification within advanced or complex aircrew systems. It suggests reasons for current inadequacies in the use of HF in the design process, giving some examples in support, and suggesting an avenue towards the improvement of the HF certification process. The importance of human cognition to the operation and performance of advanced aircrew systems has been stressed. Many of the shortfalls of advanced aircrew systems must be attributed to over automated designs that show little consideration on either the mental limits or the cognitive capabilities of the human system component. Traditional approaches to system design and HF certification are set within an over physicalistic foundation. Also, traditionally it was assumed that physicalistic system functions could be attributed to either the human or the machine on a one to one basis. Moreover, any problems associated with the parallel needs, or promoting human understanding alongside system operation and direction, were generally equated in reality by the natural flexibility and adaptability of human skills. The consideration of the human component of a complex system is seen as being primarily based on manifestations of human behavior to the almost total exclusion of any appreciation of unobservable human mental and cognitive processes. The argument of this paper is that the considered functionality of any complex human-machine system must contain functions that are purely human and purely cognitive. Human-machine system reliability ultimately depends on human reliability and dependability and, therefore, on the form and frequency of cognitive processes that have to be conducted to support system performance. The greater the demand placed by an advanced aircraft system on the human component's basic knowledge processes or cognition, rather than on skill, the more insiduous the effects the human may have on that system. This paper discusses one example of an attempt to devise an improved method of specificaiton and certification with relation to the advanced aircrew system, that of the RN Merlin helicopter. The method is realized to have limitations in practice, these mainly associated with the late production of the system specification in relation to the system development process. The need for a careful appreciation of the capabilities and support needs of human cognition within the design process of a complex man machine system has been argued, especially with relation to the concept of system functionality. Unlike the physicalistic Fitts list, a new classification of system functionality is proposed, namely: (1) equipment - system equipment related; (2) cognitive - human cognition related; and (3) associated - necessary combinatin of equipment and cognitive. This paper has not proposed a method for a fuller consideration of cognition within systems design, but has suggested the need for such a method and indicated an avenue towards its development. Finally, the HF certification of advanced aircrew systems is seen as only being possible in a qualified sense until the important functions of human cognition are considered within the system design process. (This paper contains the opinions of its authors and does not necessarily refledt the standpoint of their respective organizations).

Macleod, Iain S.↗
NASA NTRS1988

Two-Dimensional Sequential and Concurrent Finite Element Analysis of Unstiffened and Stiffened Aluminum and Composite Panels with Hole

The results of a detailed investigation of the distribution of stresses in aluminum and composite panels subjected to uniform end shortening are presented. The focus problem is a rectangular panel with two longitudinal stiffeners, and an inner stiffener discontinuous at a central hole in the panel. The influence of the stiffeners on the stresses is evaluated through a two-dimensional global finite element analysis in the absence or presence of the hole. Contrary to the physical feel, it is found that the maximum stresses from the glocal analysis for both stiffened aluminum and composite panels are greater than the corresponding stresses for the unstiffened panels. The inner discontinuous stiffener causes a greater increase in stresses than the reduction provided by the two outer stiffeners. A detailed layer-by-layer study of stresses around the hole is also presented for both unstiffened and stiffened composite panels. A parallel equation solver is used for the global system of equations since the computational time is far less than that using a sequential scheme. A parallel Choleski method with up to 16 processors is used on Flex/32 Multicomputer at NASA Langley Research Center. The parallel computing results are summarized and include the computational times, speedups, bandwidths, and their inter-relationships for the panel problems. It is found that the computational time for the Choleski method decreases with a decrease in bandwidth, and better speedups result as the bandwidth increases.

Razzaq, Zia↗
NASA NTRS1989

SHARP: A multi-mission artificial intelligence system for spacecraft telemetry monitoring and diagnosis

The Spacecraft Health Automated Reasoning Prototype (SHARP) is a system designed to demonstrate automated health and status analysis for multi-mission spacecraft and ground data systems operations. Telecommunications link analysis of the Voyager 2 spacecraft is the initial focus for the SHARP system demonstration which will occur during Voyager's encounter with the planet Neptune in August, 1989, in parallel with real time Voyager operations. The SHARP system combines conventional computer science methodologies with artificial intelligence techniques to produce an effective method for detecting and analyzing potential spacecraft and ground systems problems. The system performs real time analysis of spacecraft and other related telemetry, and is also capable of examining data in historical context. A brief introduction is given to the spacecraft and ground systems monitoring process at the Jet Propulsion Laboratory. The current method of operation for monitoring the Voyager Telecommunications subsystem is described, and the difficulties associated with the existing technology are highlighted. The approach taken in the SHARP system to overcome the current limitations is also described, as well as both the conventional and artificial intelligence solutions developed in SHARP.

Lawson, Denise L.↗
NASA NTRS2000

A Structured Light Sensor System for Tree Inventory

Tree Inventory is referred to measurement and estimation of marketable wood volume in a piece of land or forest for purposes such as investment or for loan applications. Exist techniques rely on trained surveyor conducting measurements manually using simple optical or mechanical devices, and hence are time consuming subjective and error prone. The advance of computer vision techniques makes it possible to conduct automatic measurements that are more efficient, objective and reliable. This paper describes 3D measurements of tree diameters using a uniquely designed ensemble of two line laser emitters rigidly mounted on a video camera. The proposed laser camera system relies on a fixed distance between two parallel laser planes and projections of laser lines to calculate tree diameters. Performance of the laser camera system is further enhanced by fusion of information induced from structured lighting and that contained in video images. Comparison will be made between the laser camera sensor system and a stereo vision system previously developed for measurements of tree diameters.

Chien, Chiun-Hong↗
DOE OSTI2022

OpenMP Target Task: Tasking and Target Offloading on Heterogeneous Systems

This work evaluated the use of OpenMP tasking with target GPU offloading as a potential solution for programming productivity and performance on heterogeneous systems. Also, it is proposed a new OpenMP specification to make the implementation of heterogeneous codes simpler by using OpenMP target task, which integrates both OpenMP tasking and target GPU offloading in a single OpenMP pragma. As a test case, the authors used one of the most popular and widely used Basic Linear Algebra Subprogram Level-3 routines: triangular solver (TRSM). To benefit from the heterogeneity of the current high-performance computing systems, the authors propose a different parallelization of the algorithm by using a nonuniform decomposition of the problem. This work used target GPU offloading inside OpenMP tasks to address the heterogeneity found in the hardware. This new approach can outperform the state-of-the-art algorithms, which use a uniform decomposition of the data, on both the CPU-only and hybrid CPU-GPU systems, reaching speedups of up to one order of magnitude. The performance that this approach achieves is faster than the IBM ESSL math library on CPU and competitive relative to a highly optimized heterogeneous CUDA version. One node of Oak Ridge National Laboratory’s supercomputer, Summit, was used for performance analysis.

Valero Lara, Pedro↗
NASA NTRS1999

Parallel Visualization Co-Processing of Overnight CFD Propulsion Applications

An interactive visualization system pV3 is being developed for the investigation of advanced computational methodologies employing visualization and parallel processing for the extraction of information contained in large-scale transient engineering simulations. Visual techniques for extracting information from the data in terms of cutting planes, iso-surfaces, particle tracing and vector fields are included in this system. This paper discusses improvements to the pV3 system developed under NASA's Affordable High Performance Computing project.

Edwards, David E.↗
NASA NTRS1980

Online assessment of a distributed processor

ORT (Operational Readiness Test) software allows one engineer to test readiness of 64 minicomputers and their peripherals from single console. Software makes roll call of computers and peripherals via common data buffer to check readiness of system in morning "wake up" or at other important times. Subsystems are tested in parallel to save time. "Watchdog" terminates test of any system that does not respond in time, so one failed system does not halt test sequence. Entire rollcall is complete in about 15 minutes. Software is designed for Space Shuttle prelaunch checkout, but approach should interest users of similar equipment.

Ehrlich, L. F.↗
NASA NTRS1992

Change in the coil distribution of electrodynamic suspension system

At the Miyazaki Maglev Test Center, the initial test runs were completed using a system design that required the superconducting coils to be parallel with the ground levitation coils. Recently, the coil distribution was changed to a system such that the two types of coils were perpendicular to each other. Further system changes will lead to the construction of a side wall levitation system. It is hoped that the development will culminate in a system whereby a superconducting coil will maintain all the functions: levitation, propulsion, and guidance.

Tanaka, Hisashi↗
NASA NTRS1992

Operator assistant to support deep space network link monitor and control

Preparing the Deep Space Network (DSN) stations to support spacecraft missions (referred to as pre-cal, for pre-calibration) is currently an operator and time intensive activity. Operators are responsible for sending and monitoring several hundred operator directivities, messages, and warnings. Operator directives are used to configure and calibrate the various subsystems (antenna, receiver, etc.) necessary to establish a spacecraft link. Messages and warnings are issued by the subsystems upon completion of an operation, changes of status, or an anomalous condition. Some points of pre-cal are logically parallel. Significant time savings could be realized if the existing Link Monitor and Control system (LMC) could support the operator in exploiting the parallelism inherent in pre-cal activities. Currently, operators may work on the individual subsystems in parallel, however, the burden of monitoring these parallel operations resides solely with the operator. Messages, warnings, and directives are all presented as they are received; without being correlated to the event that triggered them. Pre-cal is essentially an overhead activity. During pre-cal, no mission is supported, and no other activity can be performed using the equipment in the link. Therefore, it is highly desirable to reduce pre-cal time as much as possible. One approach to do this, as well as to increase efficiency and reduce errors, is the LMC Operator Assistant (OA). The LMC OA prototype demonstrates an architecture which can be used in concert with the existing LMC to exploit parallelism in pre-cal operations while providing the operators with a true monitoring capability, situational awareness and positive control. This paper presents an overview of the LMC OA architecture and the results from initial prototyping and test activities.

Cooper, Lynne P.↗
NASA NTRS1990

Pressure Measurement Systems

System 8400 is an advanced system for measurement of gas and liquid pressure, along with a variety of other parameters, including voltage, frequency and digital inputs. System 8400 offers exceptionally high speed data acquisition through parallel processing, and its modular design allows expansion from a relatively inexpensive entry level system by the addition of modular Input Units that can be installed or removed in minutes. Douglas Juanarena was on the team of engineers that developed a new technology known as ESP (electronically scanned pressure). The Langley ESP measurement system was based on miniature integrated circuit pressure-sensing transducers that communicated pressure information to a minicomputer. In 1977, Juanarena formed PSI to exploit the NASA technology. In 1978 he left Langley, obtained a NASA license for the technology, introduced the first commercial product, the 780B pressure measurement system. PSI developed a pressure scanner for automation of industrial processes. Now in its second design generation, the DPT-6400 is capable of making 2,000 measurements a second and has 64 channels by addition of slave units. New system 8400 represents PSI's bid to further exploit the $600 million U.S. industrial pressure measurement market. It is geared to provide a turnkey solution to physical measurement.

Source record↗
NASA NTRS1989

Preliminary study of a serial-parallel redundant manipulator

The manipulator design discussed here results from the examination of some of the reasons why redundancy is necessary in general purpose manipulation systems. A spherical joint design actuated in-parallel, having the many advantages of parallel actuation, is described. In addition, the benefits of using redundant actuators are discussed and illustrated in the design by the elimination of loci of singularities from the usable workspace with the addition of only one actuator. Finally, what is known by the authors about space robotics requirements is summarized and the relevance of the proposed design matched against these requirements. The design problems outlined here are viewed as much from the mechanical engineering aspect as from concerns arising from the control and the programming of manipulators.

Hayward, Vincent↗