Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oriented”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

An investigation of the phototropic effect on seedling orientation in a microgravity environment: A student involvement project

A microgravity growth chamber was designed to investigate the phototropic response of radish seedlings. Enclosed in a one fourth inch thick, hexagonal, fiberglass-foam spacepak nineteen inches across corners, the experiment consists of a growth chamber and germination tray, a water reservoir and solenoid valve, a fluorescent light for photo simulation, a Minolta X700 camera with programmable back, a 50 mm macro lens and flash, a battery pack, and a computer controller. Two temperature sensors and one light sensor located in the walls of the growth chamber provide temperature and illumination data. A computer provides 8 K command and 34 K data storage capability. The experiment was not activated during the STS flight because a malfunctioning latching relay stuck and reduced the battery power level.

Barainca, J. W.↗

Orientation and Morphology Effects in Rapid Silicon Sheet Solidification

Radial growth anisotropies and equilibrium forms of point nucleated, dislocation free silicon sheets spreading horizontally on the free surface of a silicon melt were measured for (100), (110), (111), and (112) sheet planes. The growth process was recorded. Qualitative Wulff surface free energy polar plots were deduced from the equilibrium shapes for each sheet plane. Predicted geometries for the tip shape of unidirectional, dislocation free, horizontally grown sheets growing in various directions within the planes were analyzed. Polycrystalline sheets and dendrite propagation were analyzed. For dendrites, growth rates on the order of 2.5 m/min and growth rate anisotropies of 25 are measured.

Ciszek, T. F.↗

Space Station Needs, Attributes and Architectural Options. Contractor orientation briefings

Requirements are considered for user missions involving life sciences; astrophysics, environmental observation; Earth and planetary exploration; materials processing; Spacelab payloads; technology development; and communications are analyzed. Plans to exchange data with potential cooperating nations and ESA are reviewed. The capability of the space shuttle to support space station activities are discussed. The status of the OAST space station technology study, conceptual architectures for a space station, elements of the space-based infrastructure, and the use of the shuttle external tank are also considered.

Source record↗

Implicit, nonswitching, vector-oriented algorithm for steady transonic flow

A rapid computation of a sequence of transonic flow solutions has to be performed in many areas of aerodynamic technology. The employment of low-cost vector array processors makes the conduction of such calculations economically feasible. However, for a full utilization of the new hardware, the developed algorithms must take advantage of the special characteristics of the vector array processor. The present investigation has the objective to develop an efficient algorithm for solving transonic flow problems governed by mixed partial differential equations on an array processor.

Lottati, I.↗

Design oriented identification of critical times in transient response

Two techniques are presented for reducing the computational effort in identifying the critical time points. One approach is an adaptive search technique, well suited for the case where the response is exactly known. The other technique, useful for noisy response, is based on a least-squares spline approximation of the response. The possibility of grouping several closely spaced local peaks to identify a single super peak from each group is also investigated. The computational efficiency of the techniques proposed here is illustrated by two examples.

Haftka, R. T.↗

Dynamics of flexible bodies in tree topology - A computer oriented approach

An approach suited for automatic generation of the equations of motion for large mechanical systems (i.e., large space structures, mechanisms, robots, etc.) is presented. The system topology is restricted to a tree configuration. The tree is defined as an arbitrary set of rigid and flexible bodies connected by hinges characterizing relative translations and rotations of two adjoining bodies. The equations of motion are derived via Kane's method. The resulting equation set is of minimum dimension. Dynamical equations are imbedded in a computer program called TREETOPS. Extensive control simulation capability is built in the TREETOPS program. The simulation is driven by an interactive set-up program resulting in an easy to use analysis tool.

Singh, R. P.↗

Radio interferometric determination of intercontinental baselines and earth orientation utilizing deep space network antennas - 1971 to 1980

Progress has been made toward the realization of the potential of radio interferometry for measuring crustal motions and global rotations of the earth with accuracies at the centimeter level. In this connection, a series of experiments, primarily with NASA's Deep Space Network (DSN) antennas, has been conducted to develop two generations of very long baseline interferometric (VLBI) systems. A description is presented of the employed techniques, an analysis of the experiments, and the results of geophysical significance. Attention is given to the interferometry technique, the geometric delay model, propagation media calibrations, and the observing strategy.

Sovers, O. J.↗

Forecasts of the 500 mb height using a dynamically oriented statistical model

The forecast skill of a simple dynamically inspired statistical model of the Northern Hemisphere 500 mb height field is evaluated in spectral and physical space for a variety of forecast lead times (1-32 days) and predictand averaging times (1-32 days). The model includes viscous damping, wave propagation, climatology and implicit stochastic forcing. The largest model skill was found for forecasts of the zonal flow and the largest waves. In general, the largest forecast skills were also associated with the largest forecast error, there being a slight geographic phase shift of the skill with respect to the error. Model skills for climate (time-averaged) forecasts are greater when using instantaneous rather than time averages to forecast time averages. Analysis of model errors suggests areas for improvement in representing forcing terms and model physics. However, the model error fields are largely 'white noise' which suggests that global forecast skills substantially larger than those obtained here are unlikely to be achieved by more sophisticated models.

Roads, J. O.↗

Orienting Arc Lamps for Longest Life

Temperature distribution strongly affects performance. Tests on floodlights for Space Shuttle payload bay show useful life of metal halide dc arc lamp prolonged by mounting "anode down" and wiring for maximum heat conduction away from electrodes. Anode-down configuration, anode and cathode temperatures stabilize at 333 degrees and 313 degrees C, respectively, after 1 hour of operation. Temperatures both below limit for quartz-to-metal seals, and lamps able to withstand a 2,000-hour life test with satisfactory light output at end.

Kiss, J.↗

Effect of combined pressure and temperature distortion orientation on high-bypass-ratio turbofan engine stability

Total-temperature, static-pressure and total-pressure distributions were measured in the inlet duct upstream of the engine inlet and within the fan and compressor of a YTF34 turbofan engine. Free-stream and boundary layer yaw angle variations were measured between a rotable screen assembly and the engine inlet. Total pressure distortions were generated using three 180 deg extent screens and total temperature distortions were generated using a rotatable hydrogen burner. Reynolds number index upstream of the rotatable screen assembly was maintained at 0.5 (based on the undistorted sectors at station 1, the inlet flow measuring station). The engine mechanical fan speed at sea level condition was rated at 7005 rpm. The engine was tested at a corrected fan speed of 90 percent of rated condition. Yaw angle increased between the rotatable screen assembly and the engine inlet. The largest variation in free-stream and boundary layer yaw angle occurs when the combined distortions are 180 deg out-of-phase. Static-pressure distortion increased exponentially as flow approached the engine. Total-pressure distortions were attenuated between the engine inlet and the compressor exit. Total-temperature distortion persisted through the compressor for all four combined distortions investigated.

Soeder, R. H.↗

Assessing the Subjective Workload of Directional Orientation Tasks

The impact of various flight-related tasks on the workload imposed by the requirement to compute new headings, course changes, and reciprocal headings was investigated. Eight pilots were presented with a series of heading-change tasks in a laboratory setting. Two levels of difficulty of each of three tasks were presented verbally and spatially. Performance was measured by evaluating the speed and accuracy of the responses. The subjective responses and objective measures of performance reflected a strong association between subjective experience and objective behavior. The reciprocal calculations were performed quickly and accurately throughout and were considered to be minimally loading. Subjective workload, percent correct and response times for the two course-change tasks varied significantly as a function of level of difficulty and display format, with no discernable speed/accuracy trade off.

Miller, R. C.↗

Mission-oriented requirements for updating MIL-H-8501. Volume 1: STI proposed structure

The structure of a new flying and ground handling qualities specification for military rotorcraft is presented. This preliminary specification structure is intended to evolve into a replacement for specification MIL-H-8501A. The new structure is designed to accommodate a variety of rotorcraft types, mission flight phases, flight envelopes, and flight environmental characteristics and to provide criteria for three levels of flying qualities, a systematic treatment of failures and reliability, both conventional and multiaxis controllers, and external vision aids which may also incorporate synthetic display content. Existing and new criteria were incorporated into the new structure wherever they could be substantiated.

Clement, W. F.↗

Mission-oriented requirements for updating MIL-H-8501. Volume 2: STI background and rationale

A supplement to the structure of a new flying and ground handling qualities specification for military rotorcraft structure is presented in order to explain the background and rationale for the specification structure, the proposed forms of criteria, and the status of the existing data base. Critical gaps in the data base for the new structure are defined, and recommendations are provided for the research required to address the most important of these gaps.

Clement, W. F.↗

Influence of interface ply orientation on fatigue damage of adhesively bonded composite joints

An experimental study of cracked-lap-shear specimens was conducted to determine the influence of adherend stacking sequence on debond initiation and damage growth in a composite-to-composite bonded joint. Specimens consisted of quasi-isotropic graphite/epoxy adherends bonded together with either FM-300 or EC 3445 adhesives. The stacking sequence of the adherends was varied such that 0 deg, 45 deg, or 90 deg plies were present at the adherend-adhesive interfaces. Fatigue damage initiated in the adhesive layer in those specimens with 0 deg nd 45 deg interface plies. Damage initiated in the form of ply cracking in the strap adherend for the specimens with 90 deg interface plies. The fatigue-damage growth was in the form of delamination within the composite adherends for specimens with the 90 deg and 45 deg plies next to the adhesive, while debonding in the adhesive resulted for the specimens with 0 deg plies next to the adhesive. Those joints with the 0 deg and 45 deg plies next to either adhesive has essentially the same fatigue-damage-initiation stress levels. These stress levels were 13 and 71 percent higher, respectively, than those for specimens with 90 deg plies next to the EC 3445 and FM-300 adhesives.

Johnson, W. S.↗

The Mission Oriented Terminal Area Simulation (MOTAS)

A new simulation facility is described in which flight management and flight operations research studies can be conducted in a highly realistic terminal area environment. The historical evolution and justification of the facility is discussed, along with the design configuration of the system hardware and software. Details are provided on the traffic management features of the terminal area model as well as the human controller and multicockpit interface capabilities. The facility is currently operational with two cockpit simulators, two air traffic control (ATC) stations, four pseudo pilot stations (PPS), a metering and spacing system of traffic flow control management, and terminal area models providing two route structure environments: area navigation (RNAV) for advanced-equipped aircraft and vectoring for conventionally-equipped aircraft. Plans for future experiments utilizing the facility are discussed.

Naftel, P. B.↗

The rotation period and pole orientation of asteroid 4 Vesta

In 1971 asteroid Vesta was observed in a region of the sky in which it had never been observed before. Its photometric lightcurve had two distinct maxima. Those observations have been the only strong evidence to support a rotation period of about 10 hr 41 min. Lightcurves made in 1982, when Vesta was at the same aspect as 1971, do not show two different maxima. It is concluded that there was a systematic error in the 1971 observations. At this time a definitive statement cannot be made about the true period of Vesta, although the 5 hr 20 min period does appear more plausible. Radar echoes in 1988 and 1992 should resolve the problem. The shorter rotation period was assumed and the photometric astrometry method applied. The sidereal period is 5 hr 20 min 31.68 sec (0.2225889 + or 0.0000002 days), the rotation is prograde, and the coordinates of the north pole are 103 deg longitude and + 43 deg latitude with an uncertainty of about 6 deg.

Taylor, R. C.↗