Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “furnace”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Development of advanced methods for continuous Czochralski growth. Silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

The three components required to modify the furnace for batch and continuous recharging with granular silicon were designed. The feasibility of extended growth cycles up to 40 hours long was demonstrated by a recharge simulation experiment; a 6 inch diameter crystal was pulled from a 20 kg charge, remelted, and pulled again for a total of four growth cycles, 59-1/8 inch of body length, and approximately 65 kg of calculated mass.

Wolfson, R. G.↗
NASA NTRS1977

Energy Conversion Alternatives Study (ECAS)

ECAS compared various advanced energy conversion systems that can use coal or coal-derived fuels for baseload electric power generation. It was conducted in two phases. Phase 1 consisted of parametric studies. From these results, 11 concepts were selected for further study in Phase 2. For each of the Phase 2 systems and a common set of ground rules, performance, cost, environmental intrusion, and natural resource requirements were estimated. In addition, the contractors defined the state of the associated technology, identified the advances required, prepared preliminary research and development plans, and assessed other factors that would affect the implementation of each type of powerplant. The systems studied in Phase 2 include steam systems with atmospheric- and pressurized-fluidized-bed boilers; combined cycle gas turbine/steam systems with integrated gasifiers or fired by a semiclean, coal derived fuel; a potassium/steam system with a pressurized-fluidized-bed boiler; a closed-cycle gas turbine/organic system with a high-temperature, atmospheric-fluidized-bed furnace; a direct-coal-fired, open- cycle magnetohydrodynamic/steam system; and a molten-carbonate fuel cell/steam system with an integrated gasifier. The sensitivity of the results to changes in the ground rules and the impact of uncertainties in capital cost estimates were also examined.

Source record↗
NASA NTRS1978

Catalytic decomposition of methanol for onboard hydrogen generation

The steam reformation of an equimolar mixture of methanol and water on a copper chromite catalyst was studied at three furnace temperatures and at feed space velocities from 800 to 2600 per hour. The hydrogen space velocity could be related to the reactor temperature by the equation Sv = A exp (-omega T), where A and omega are constants determined for each value of alpha and T is temperature. At a methanol conversion of 0.87 and a reactor temperature of 589 K, the extrapolated value of the hydrogen space velocity was 9400 per hour. This velocity was used to estimate the size of an onboard hydrogen reactor for automotive applications. Such a reactor would need only about 0.8 liter of catalyst to produce 7630 STP liters (1.5 lb) of hydrogen per hour. This quantity of catalyst would fit into nine tubes 17.8 centimeters along and 2.54 centimeters in inside diameter, which is smaller than most mufflers. The reactor products would contain 12 to 13 percent more chemical energy than the incoming methanol and water.

Brabbs, T.↗
NASA NTRS1977

Apollo-Soyuz pamphlet no. 8: Zero-g technology

The behavior of liquids in zero gravity environments is discussed with emphasis on foams, wetting, and wicks. A multipurpose electric furnace (MA-010) for the high temperature processing of metals and salts in zero-g is described. Experiments discussed include: monolectic and synthetic alloys (MA-041); multiple material melting point (MA-150); zero-g processing of metals (MA-070); surface tension induced convection (MA-041); halide eutectic growth; interface markings in crystals (MA-060); crystal growth from the vapor phase (MA-085); and photography of crystal growth (MA-028).

Page, L. W.↗
NASA NTRS1978

Performance of a thermionic converter module utilizing emitter and collector heat pipes

A thermionic converter module simulating a configuration for an out-of-core thermionic nuclear reactor was designed, fabricated, and tested. The module consists of three cylindrical thermionic converters. The tungsten emitter of the converter is heated by a tungsten, lithium heat pipe. The emitter heat pipes are immersed in a furnace, insulated by MULTI-FOIL thermal insulation, and heated by tungsten radiation filaments. The performance of each thermionic converter was characterized before assembly into the module. Dynamic voltage, current curves were taken using a 60 Hz sweep and computerized data acquisition over a range of emitter, collector, and cesium-reservoir temperatures. An output power of 215 W was observed at an emitter temperature of 1750 K and a collector temperature of 855 K for a two diode module. With a three diode module, an output power of 270 W was observed at an average emitter temperature of 1800 K and a Collector temperature of 875 K.

Kroeger, E. W.↗
NASA NTRS1978

Effects of compositional changes on the performance of a thermal barrier coating system

Currently proposed thermal barrier systems for aircraft gas turbine engines consist of NiCrAlY bond coating covered with an insulating oxide layer of yttria-stabilized zirconia. The effect of yttrium concentration (from 0.15 to 1.08 w/o) in the bond coating and the yttria concentration (4 to 24.4 w/o) in the oxide layer were evaluated. Furnace, natural gas-oxygen torch, and Mach 1.0 burner rig cyclic tests on solid specimens and air-cooled blades were used to identify trends in coating behavior. Results indicate that the combinations of yttrium levels between 0.15 - 0.35 w/o in the bond coating and the yttria concentration between 6 - 8 w/o in the zirconium oxide layer were the most adherent and resistant to high temperature cyclic exposure.

Stecura, S.↗
NASA NTRS1978

Vapor transport mechanisms

The Raman scattering furnace for investigating vapor transport mechanisms was completed and checked out. Preliminary experiments demonstate that a temperature resolution of plus and minus 5 C is possible with this system operating in a backscatter mode. In the experiments presented with the GeI 4 plus excess Ge system at temperatures up to 600 C, only the GeI4 band at 150 cm superscript minus 1 was observed. Further experiments are in progress to determine if GeI2 does become the major vapor species above 440 C.

Workman, G. L.↗
NASA NTRS1976

Silicon solar cells by ion implantation and pulsed energy processing

A new method for fabrication of silicon solar cells is being developed around ion implantation in conjunction with pulsed electron beam techniques to replace conventional furnace processing. Solar cells can be fabricated totally in a vacuum environment at room temperature. Cells with 10% AM0 efficiency have been demonstrated. High efficiency cells and effective automated processing capabilities are anticipated.

Kirkpatrick, A. R.↗
NASA NTRS1976

Economic analysis of low cost silicon sheet produced from Czochralski grown material

This study shows that the lower limits for manufacturing add-on costs to convert polysilicon to wafers is in the range of $22 to $26/sq m with the cost about equally divided between the crystal growth and wafering processes. However, the $22 to $26/sq m cost limit should be viewed as an asymptote since it is based on multicharge or continuous growth configurations, solidification rates in excess of 2 Kg/hr, multiblade wafering and a slice plus kerf of .045 cm. It should also be emphasized that the results of this study are based on as-sawn wafers, 100% yields (growth and slicing) and no profit. To the first approximation, the limiting cost factors are crucible material and furnace parts for growth and blade material and slurry for slicing.

Koliwad, K. M.↗
NASA NTRS1977

Evaluation of low cost/high temperature fiber and blanket insulation

Twelve fiber materials comprising water-felted fiber cakes and blanket insulation were subjected to furnace exposures at 1000, 1200, 1400, and 1600 C for up to 500 hours to establish the time-temperature limits below which these insulation materials can withstand repeated thermal cycles without detrimental shrinkage, thermal conductivity increase, or physical changes. Test samples were inspected periodically during the exposure cycles and weight loss and dimensional shrinkage were measured. Density, fiber crystallography, and thermal conductivity were measured after exposure and properties were compared with those of unexposed controls.

Strauss, E. L.↗
NASA NTRS1977

Open-Cycle Gas Turbine/Steam Turbine Combined Cycles with synthetic fuels from coal

The Open-Cycle Gas Turbine/Steam Turbine Combined Cycle can be an effective energy conversion system for converting coal to electricity. The intermediate step in this energy conversion process is to convert the coal into a fuel acceptable to a gas turbine. This can be accomplished by producing a synthetic gas or liquid, and by removing, in the fuel conversion step, the elements in the fuel that would be harmful to the environment if combusted. In this paper, two open-cycle gas turbine combined systems are evaluated: one employing an integrated low-Btu gasifier, and one utilizing a semi-clean liquid fuel. A consistent technical/economic information base is developed for these two systems, and is compared with a reference steam plant burning coal directly in a conventional furnace.

Shah, R. P.↗
NASA NTRS1978

Measurement of the time-temperature dependent dynamic mechanical properties of boron/aluminum composites

A relatively simple flexural vibration test is developed for accurate measurement of the low-strain dynamic modulus and damping capacity of B/Al composite bar specimens from -200 C to over 500 C. The specimens are prepared from 8-ply unidirectional panels containing 50 volume percent fibers composed of 203-micron commercial boron-on-tungsten fibers. The basic test technique consists of the forced flexural vibration of the composite bar specimens at their two lowest free-free symmetrical resonant modes in a high-vacuum cryostat furnace. Specimen damping is determined from oscilloscope photographs of the free decay obtained after simultaneously removing the resonant drive signal and grounding the vibration-drive electrode. The availability of time-temperature dynamic data coupled with the predictive accuracy of composite theory suggests a future potential for using such data in examining environmental effects on composite macrostructure and microstructure.

Dicarlo, J. A.↗
NASA NTRS1977

Dynamic crystallization experiments bearing on the origin of textures in impact-generated liquids

Dynamic crystallization experiments on a synthetic glass of 14310 composition show that the density and distribution of crystals present at the initiation of cooling can drastically affect the texture of the crystallized product. Experiments were performed in one-atmosphere gas-mixing furnaces at an oxygen fugacity slightly below iron-wustite, and precooling crystallization, cooling history, and melt history were systematically varied. When cooled from a complete liquid, the experimental charges were porphyritic with 1-2 mm phenocrysts set in a very fine-grained matrix (less than 0.1 mm). This result suggests that 14310 did not cool from a complete melt. When cooled from a crystal-liquid mixture, the experimental charges had widely varying textures depending on the density and distribution of crystals that act as nucleation sites. It is suggested that the close spatial association of widely divergent textures in the matrices of some breccias and rocks might arise in this manner; local variations in cooling rates are not required.

Lofgren, G. E.↗
NASA NTRS1975

Experimental modeling of the cooling history of Apollo 12 olivine basalts

An analog of the Apollo 12 olivine vitrophyres has been crystallized in a 1-atm gas-mixing furnace at cooling rates ranging between 1250 and 0.7 C/hr and isothermally at degrees of supercooling ranging from 10 C to 325 C. Mineral chemistry, crystal shapes, grain sizes and textures are systematically related to cooling rate and degree of supercooling. At linear cooling rates not exceeding 40 C/hr the texture is porphyritic - large olivine crystals are set in a groundmass of finer-grained pyroxene, plagioclase, and ilmenite; a later generation of olivine never crystallizes. There are three shapes of olivine crystals in the Apollo 12 olivine vitrophyres: glomerocrysts of subhedral crystals, large subequant skeletons, and highly elongate skeletons. These result from three generations of nucleation and a two-stage cooling history - a slow preeruption stage and a rapid continuously increasing posteruption stage. It seems likely that the Apollo 12 olivine basalt magmas were erupted with olivine crystals in suspension. The nucleation temperature of olivine in cooling-rate experiments is dependent on the experimental technique, and hence results of cooling experiments should be applied with caution.

Donaldson, C. H.↗
NASA NTRS1979

Differential oil flowmeter

Difference in oil flow volume through two mechanical flowmeters is converted to analog signal by simple inexpensive circuit. Circuit can be implemented with only minor changes to conventional oil flowmeters and used to measure fuel consumed by oil fired furnace or water heater.

Powers, W. T.↗
NASA NTRS1980

Repairing ceramic insulating tiles

Fused-silica tiles containing large voids or gauges are repaired without adhesives by plug insertion method. Tiles are useful in conduits for high-temperature gases, in furnaces, and in other applications involving heat insulation.

Dunn, B. R.↗
NASA NTRS1980

Thermal jack

Auxiliary furnace tool forces part to match length of mating part during brazing. As brazed assembly cools, jack contracts faster and disengages from fitting studs.

Armenoff, C. T.↗