Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “feedback control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Reduced-Order Aerodynamic Modeling Based on CFD Frequency Responses from Multisine Inputs

A system identification analysis was performed to determine a reduced-order model (ROM) of a computational fluid dynamics (CFD) solver in support of linear aeroservoelastic model development and feedback control design. The approach was applied to the FUN3D code for the half-span wind tunnel test article used in the NASA-Boeing collaboration called the Integrated Adaptive Wing Technology Maturation (IAWTM) project. In a transonic flow condition, multiple inputs (11 structural mode displacements and 3 control surface deflections) were simultaneously excited with orthogonal phase-optimized multisines while multiple outputs (the corresponding 14 generalized aerodynamic forces) were recorded. From these recorded times series, the matrix of frequency responses was computed and subsequently fit using rational function approximations (RFAs). It was found that the entire (14 x 14) matrix of frequency responses could be determined from a single CFD run and that results generally followed trends predicted using other methods. Differences were attributed to the modeling fidelity and nonlinearities from structural mode and control surface interactions at higher reduced frequencies. More accurate fits of the RFAs to the frequency response data were obtained by making two CFD runs, one with only structural mode excitations and one with only control surface excitations, which reduced the degree of nonlinearity in the modeling data.

Aeroservoelasticity↗
NASA NTRSDate not supplied

Large-scale Additive Manufacturing for Exploration

Additive Manufacturing (AM) is emerging as a mainstream manufacturing technology, and demand for large part manufacturing is getting stronger. Direct Metal Deposition (DMD) is a DED technology based on laser and powder metal application using a closed-loop-feedback control system. This webinar focuses on additive manufacturing of NASA’s RS-25 engine nozzle liner using DMD technology. This liner (10ft in height and 8ft in diameter) is beyond the print capability of existing 3D printing processes. To print this part, significant advancements were made to the DMD technology by deploying two process heads in the machine and expanding the machine work envelop to allow manufacturing of such large parts in a safe and efficient environment. A successful demonstration of the AM of the RS25 engine nozzle liner marks a new era in 3D printing and elevates the current 3D printing technology to a new level for affordable manufacturing of large metal parts.

Additive Manufacturing↗
NASA NTRS2020

Detection and Mitigation of Transient Instabilities in Multi-Agent Systems and Swarms

We first introduce the novel concept of transient instabilities in multi-agent systems and swarms, i.e., a small disturbance leads to increasing-amplitude oscillations throughout the swarm, which results in a large number of inter-agent collisions. This instability is dominant in the transient phase of the system and it does not appear in the steady-state behavior of the system, as each agent uses Lyapunov-stable feedback control laws. We present a rigorous definition of transient instability in swarms, and discuss its key properties. We also present a sufficient condition to check if a swarm will be transient stable. We study the behaviour of different control laws under this condition. We also show how transient instability phenomenon could impact the dynamics of deployable structures. Next, we present a novel control architecture that augments the baseline formation maintenance controller to mitigate transient instabilities. At its heart, the proposed architecture consists of a projection operator based estimator disguised as a reference model that generates collision-free trajectories for the agents to follow. We present numerical simulation results to demonstrate the effectiveness of our proposed approaches.

Quadrelli, Marco B.↗
NASA NTRSDate not supplied

Recent System Identification Research at NASA Langley Research Center

This talk summarizes some of the recent advances in system identification at NASA Langley Research Center. Efforts discussed were applied to aeroelastic models, aircraft with redundant inputs and feedback control active, and aircraft flying in turbulence. Topics mentioned include experiment design with orthogonal multisine inputs, frequency response estimation, maximum likelihood parameter estimation, and parameter estimation considering process noise.

NASA LaRC↗
NASA NTRSDate not supplied

Parametric Mechanism Design Through Numerical Optimization and Physics Simulation

Design-Build-Test approaches for developing spaceflight hardware are prohibitively time and cost intensive and often lead to suboptimal mechanism designs. Approaches that couple machine learning and high-fidelity physics simulation could eliminate the need for hardware prototyping and dramatically accelerate the engineering design cycle, ultimately reducing cost. This work presents a modular NASA-developed toolchain to optimize hardware mechanisms in a virtual environment using numerical optimization and multi-body physics simulation. The toolchain enables multi-objective optimization, generates parametric CAD files that can be further post-processed by an end user, and can be expanded to optimize full systems and non-mechanical parameters such as feedback control variables. We demonstrate the toolchain through an independently verifiable design problem that optimizes wheel radius to achieve a desired linear velocity in a rigid-body physics environment when the wheel rotates at a constant angular speed, and then post-process the parametric CAD file of the optimal design generated by the tool before ultimately manufacturing it via 3D printing. We end with a discussion of how the toolchain can incorporate other analysis tools, including finite element analysis, computational fluid dynamics, and granular media simulations.

Optimization↗
NASA NTRSDate not supplied

An Optimization-Based Toolchain for Parametric Mechanism Design

Design-Build-Test approaches for developing spaceflight hardware are prohibitively time and cost intensive and often lead to suboptimal mechanism designs. Approaches that couple machine learning and high-fidelity physics simulation could eliminate the need for hardware prototyping and dramatically accelerate the engineering design cycle, ultimately reducing cost. This work presents a modular NASA-developed toolchain to optimize hardware mechanisms in a virtual environment using numerical optimization and multi-body physics simulation. The toolchain enables multi-objective optimization, generates parametric CAD files that can be further post-processed by an end user, and can be expanded to optimize full systems and non-mechanical parameters such as feedback control variables. We demonstrate the toolchain through an independently verifiable design problem that optimizes wheel radius to achieve a desired linear velocity in a rigid-body physics environment when the wheel rotates at a constant angular speed, and then post-process the parametric CAD file of the optimal design generated by the tool before ultimately manufacturing it via 3D printing. We end with a discussion of how the toolchain can incorporate other analysis tools, including finite element analysis, computational fluid dynamics, and granular media simulations.

Optimization↗
NASA NTRSDate not supplied

Experimental and Computational Investigation of Valve Motion in a Resonant Pulse Combustor

The motion of a passive reed-type valve and a poppet-style valve operating in a small scale, liquid-fueled pulse combustor is investigated experimentally. Valve position and combustion chamber pressure are simultaneously measured using an in-house fabricated optical position probe. The reed valve configuration is found to operate in a self-aspirated mode, generating significant pressure gain. The poppet valve configuration cannot operate without forced air, and does not generate pressure gain. Both type valves are tested in combustors of multiple lengths. Close examination of the respective valve motions indicate that the reed valve is highly non-linear, with unique attributes that appear essential for self-aspiration. Dynamic models for the motion of each valve are implemented in a computational fluid dynamic (CFD) simulation of the pulse combustor in order to assess if this unique valve motion is critical to successful operation. The results show that it is. The implications of these results are discussed. The need for active actuation with feedback control, rather than passive valve actuation is highlighted as a critical technology for practical resonant pulse combustors.

Combustion↗
NASA NTRSDate not supplied

Parametric Optimization of Rigid Wheels for Planetary Surface Mobility Applications

Design-Build-Test approaches for spaceflight hardware are time and cost intensive, which can result in suboptimal mechanism designs. Optimization-based approaches that utilize high-fidelity models and physics simulation could overcome these limitations while simultaneously speeding up the mechanical design process and reducing cost. In this work, we present a toolchain that enables the multi-objective optimization of rigid rover wheels for planetary surface mobility applications. The toolchain uses Chrono’s Continuous Representation Model (CRM) functionality to simulate granular soil and performs multi-objective parametric optimization on candidate rover wheels to meet a desired performance criterion. The resulting wheel design is then evaluated experimentally using a single-wheel testbed. We end with a discussion of how the toolchain can be extended to simultaneously co-optimize other system parameters, such as system power consumption and feedback control gains.

Optimization↗
NASA NTRSDate not supplied

Experimental and Computational Investigation of Valve Motion in a Resonant Pulse Combustor

The motion of a passive reed-type valve and a poppet-style valve operating in a small scale, liquid-fueled pulse combustor is investigated experimentally. Valve position and combustion chamber pressure are simultaneously measured using an in-house fabricated optical position probe. The reed valve configuration is found to operate in a self-aspirated mode, generating significant pressure gain. The poppet valve configuration cannot operate without forced air, and does not generate pressure gain. Both type valves are tested in combustors of multiple lengths. Close examination of the respective valve motions indicate that the reed valve is highly non-linear, with unique attributes that appear essential for self-aspiration. Dynamic models for the motion of each valve are implemented in a computational fluid dynamic (CFD) simulation of the pulse combustor in order to assess if this unique valve motion is critical to successful operation. The results show that it is. The implications of these results are discussed. The need for active actuation with feedback control, rather than passive valve actuation is highlighted as a critical technology for practical resonant pulse combustors.

Combustion↗
NASA NTRS2011

Integrated Control with Structural Feedback to Enable Lightweight Aircraft

This presentation for the Fundamental Aeronautics Program Technical Conference covers the benefits of active structural control, related research areas, and focuses on the use of optimal control allocation for the prevention of critical loads. Active control of lightweight structures has the potential to reduce aircraft weight and fuel burn. Sensor, control law, materials, control effector, and system level research will be necessary to enable active control of lightweight structures. Optimal control allocation with structural feedback has been shown in simulation to be feasible in preventing critical loads and is one example of a control law to enable future lightweight aircraft.

Taylor, Brian R.↗
NASA NTRS1987

RKH space approximations for the feedback operator in a linear hereditary control system

Computational implementation of feedback control laws for linear hereditary systems requires the approximation of infinite dimensional feedback operators with finite dimensional operators. The dense subspaces of K-polygonal functions in reproducing kernel Hilbert spaces, RKH spaces, suggest finite dimensional approximations of the matrix representations of the control operators. A convergence theorem is developed for the approximations and the numerical implementation of the approximations is discussed.

Reneke, J. A.↗
NASA NTRS1981

The Total Synthesis Problem of linear multivariable control. II - Unity feedback and the design morphism

Zames (1981) has observed that there is, in general, no 'separation principle' to guarantee optimality of a division between control law design and filtering of plant uncertainty. Peczkowski and Sain (1978) have solved a model matching problem using transfer functions. Taking into consideration this investigation, Peczkowski et al. (1979) proposed the Total Synthesis Problem (TSP), wherein both the command/output-response and command/control-response are to be synthesized, subject to the plant constraint. The TSP concept can be subdivided into a Nominal Design Problem (NDP), which is not dependent upon specific controller structures, and a Feedback Synthesis Problem (FSP), which is. Gejji (1980) found that NDP was characterized in terms of the plant structural matrices and a single, 'good' transfer function matrix. Sain et al. (1981) have extended this NDP work. The present investigation is concerned with a study of FSP for the unity feedback case. NDP, together with feedback synthesis, is understood as a Total Synthesis Problem.

Sain, M. K.↗
NASA NTRS1992

Robust control of flexible space vehicles with minimum structural excitation: On-off pulse control of flexible space vehicles

Both feedback and feedforward control approaches for uncertain dynamical systems (in particular, with uncertainty in structural mode frequency) are investigated. The control objective is to achieve a fast settling time (high performance) and robustness (insensitivity) to plant uncertainty. Preshaping of an ideal, time optimal control input using a tapped-delay filter is shown to provide a fast settling time with robust performance. A robust, non-minimum-phase feedback controller is synthesized with particular emphasis on its proper implementation for a non-zero set-point control problem. It is shown that a properly designed, feedback controller performs well, as compared with a time optimal open loop controller with special preshaping for performance robustness. Also included are two separate papers by the same authors on this subject.

Wie, Bong↗
NASA NTRS1989

Independent modal space control with positive position feedback

An independent modal space control (IMSC) algorithm is presented, whose modal control forces are generated from a positive position feedback (PPF) strategy. The proposed algorithm combines the attributes of both the IMSC and the PPF, and maintains the simplicity of the IMSC as it designs the controller of a complex structure at the uncoupled modal level. The effectiveness of the algorithm in damping out the vibration of flexible structures is validated experimentally. A simple cantilevered beam is employed as an example of a flexible structure whose multimodes of vibration are controlled by a single actuator. Performance of the active control system is determined in the frequency and the time domains. The experimental results indicate the potential of the proposed methodology as a viable method for controlling the vibration of large flexible structures.

Baz, A.↗
NASA NTRS2004

Sensory-Feedback Exoskeletal Arm Controller

An electromechanical exoskeletal arm apparatus has been designed for use in controlling a remote robotic manipulator arm. The apparatus, called a force-feedback exoskeleton arm master (F-EAM) is comfortable to wear and easy to don and doff. It provides control signals from the wearer s arm to a robot arm or a computer simulator (e.g., a virtual-reality system); it also provides force and torque feedback from sensors on the robot arm or from the computer simulator to the wearer s arm. The F-EAM enables the wearer to make the robot arm gently touch objects and finely manipulate them without exerting excessive forces. The F-EAM features a lightweight design in which the motors and gear heads that generate force and torque feedback are made smaller than they ordinarily would be: this is achieved by driving the motors to power levels greater than would ordinarily be used in order to obtain higher torques, and by providing active liquid cooling of the motors to prevent overheating at the high drive levels. The F-EAM (see figure) includes an assembly that resembles a backpack and is worn like a backpack, plus an exoskeletal arm mechanism. The FEAM has five degrees of freedom (DOFs) that correspond to those of the human arm: 1. The first DOF is that of the side-to-side rotation of the upper arm about the shoulder (rotation about axis 1). The reflected torque for this DOF is provided by motor 1 via drum 1 and a planar four-bar linkage. 2. The second DOF is that of the up-and-down rotation of the arm about the shoulder. The reflected torque for this DOF is provided by motor 2 via drum 2. 3. The third DOF is that of twisting of the upper arm about its longitudinal axis. This DOF is implemented in a cable remote-center mechanism (CRCM). The reflected torque for this DOF is provided by motor 3, which drives the upper-arm cuff and the mechanism below it. A bladder inflatable by gas or liquid is placed between the cuff and the wearer s upper arm to compensate for misalignment between the exoskeletal mechanism and the shoulder. 4. The fourth DOF is that of flexion and extension of the elbow. The reflected torque for this DOF is provided by motor 4 and drum 4, which are mounted on a bracket that can slide longitudinally by a pin-and-slot engagement with the upper-arm cuff to compensate for slight variations in the position of the kinematic center of the elbow. Attached to drum 4 is an adapter plate to which is attached a CRCM for the lower arm. 5. The lower-arm CRCM implements the fifth DOF, which is the twist of the forearm about its longitudinal axis. Motor 5 provides the reflected torque for this DOF by driving the lower-arm cuff. A rod transmits twist and torsion between the lower-arm cuff and the hand cuff. With this system, the motion of the wearer s joints and the reflected torques applied to these joints can be measured and controlled in a relatively simple manner. This is because the anthropomorphic design of the mechanism imitates the kinematics of the human arm, eliminating the need for kinematic conversion of joint-torque and joint-angle data.

An, Bin↗
NASA NTRS1973

The muscle spindle as a feedback element in muscle control

The muscle spindle, the feedback element in the myotatic (stretch) reflex, is a major contributor to muscular control. Therefore, an accurate description of behavior of the muscle spindle during active contraction of the muscle, as well as during passive stretch, is essential to the understanding of muscle control. Animal experiments were performed in order to obtain the data necessary to model the muscle spindle. Spectral density functions were used to identify a linear approximation of the two types of nerve endings from the spindle. A model reference adaptive control system was used on a hybrid computer to optimize the anatomically defined lumped parameter estimate of the spindle. The derived nonlinear model accurately predicts the behavior of the muscle spindle both during active discharge and during its silent period. This model is used to determine the mechanism employed to control muscle movement.

Andrews, L. T.↗