Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dissolving”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Electrophoretic and potentiometric signatures of multistage CaCO3 nucleation

HYPOTHESIS: Calcium carbonate nucleation is often a complex and multistep process that is difficult to follow in situ. The time-resolved electrochemical and electrophoretic methods can provide a new insight into the nucleation pathway. EXPERIMENTS: Here, we used a combination of speciation calculations with time-resolved electrophoretic and potentiometric methods to monitor calcium carbonate precipitation from a slightly supersaturated solution. FINDINGS: After an initial mixing period of three minutes in which metastable CaCO 3 phases may have nucleated and subsequently dissolved due to locally-high supersaturations, bulk solution pH and Ca 2+ concentrations stabilize before decreasing in tandem with the precipitation of a CaCO 3 phase. After an hour, the precipitate is dominated by calcite that grows at the expense of dissolving vaterite. The time-dependent electrokinetic potential shows analogous signatures of multistage nucleation process: initial rapid changes in ζ-potential are followed by much slower equilibration starting about one hour after reagents are mixed. The changes in ζ-potential, solution pH, saturation indexes, and particle morphology are consistent with vaterite to calcite transformation via dissolution of the former and recrystallization of the latter. These findings highlight the potential use of ζ-potential measurements for monitoring polymorphic transformations of carbonate phases in-situ.

36 MATERIALS SCIENCE↗

Diffusive release of uranium from contaminated sediments into capillary fringe pore water

Despite remediation efforts at the former nuclear weapons facility at the Hanford site (Washington State), leaching of uranium (U) from contaminated sediments to the ground water persists at the Hanford 300 Area. Flooding of contaminated capillary fringe sediments due to seasonal changes in the Columbia River stage has been identified as a reason of continued U supply to ground water. We investigated the release of U from Hanford capillary fringe sediments to pore water. Contaminated Hanford sediments were packed into reservoirs of centrifugal filter devices and saturated with Columbia River water for 3 to 84 days at varying solution-to-solid ratios (1:3, 1:1, 5:1, 10:1, 25:1 mL:g). After specified times, samples were centrifuged to a gravimetric water content of 0.11 ± 0.06 g g-1. Within the first three days, there was an initial rapid release of 6-9% of total U from the sediments into the pore water, independent of the solution-to-solid ratio. After 14 days of reaction, however, the experiments with the narrowest solution-to-solid ratios (1:3 and 1:1 mL:g) showed a decline in dissolved U concentrations. The removal of U from the solution phase was accompanied by removal of Ca and HCO3-. Geochemist workbench simulations, conducted using measured solution concentrations from experiments, indicated that calcite could precipitate in the 1:3 solution-to-solid ratio experiment. After the rapid initial release in the first three days for the 5:1, 10:1, and 25:1 solution-to-solid ratio experiments, there was sustained release of U into the pore water. Up to 22% of total U was released on day 84 for the 25:1 solution-to-solid ratio reaction. This sustained release of U from the sediments had diffusion-limited kinetics.

contaminated sediments↗

A consistent and conservative model and its scheme for N -phase- M -component incompressible flows

Here, we propose a consistent and conservative model for multiphase and multicomponent incompressible flows, where there can be arbitrary numbers of phases and components. Each phase has a background fluid called the pure phase, each pair of phases is immiscible, and components are dissolvable in some specific phases. The model is developed based on the multiphase Phase-Field model including the contact angle boundary condition, the diffuse domain approach, and the analyses on the proposed consistency conditions for multiphase and multicomponent flows. The model conserves the mass of individual pure phases, the amount of each component in its dissolvable region, and thus the mass of the fluid mixture, and the momentum of the flow. It ensures that no fictitious phases or components can be generated and that the summation of the volume fractions from the Phase-Field model is unity everywhere so that there is no local void or overfilling. It satisfies a physical energy law and it is Galilean invariant. A corresponding numerical scheme is developed for the proposed model, whose formal accuracy is 2nd-order in both time and space. It is shown to be consistent and conservative and its solution is demonstrated to preserve the Galilean invariance and energy law. Numerical tests indicate that the proposed model and scheme are effective and robust to study various challenging multiphase and multicomponent flows.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Reclamation of niobium compounds from ionic liquid electrochemical polishing of superconducting radio frequency cavities

Recent research has shown that choline chloride (vitamin B4)-based solutions can be used as a greener alternative to acid-based electrochemical polishing solutions. This study demonstrated a successful method for electrochemical deposition of niobium compounds onto the surface of copper substrates using a novel choline chloride-based ionic liquid. Niobium ions present in the ionic liquid solution were dissolved into the solution prior to deposition via electrochemical polishing of solid niobium. A black coating was clearly visible on the surface of the Cu following deposition. This coating was analyzed using scanning electron microscopy (SEM), electron dispersive X-ray spectroscopy (EDX), atomic force microscopy (AFM), and X-ray fluorescence spectroscopy (XRF). This ionic liquid-based electrochemical deposition method effectively recycles previously dissolved niobium from electrochemical polishing of superconducting radio frequency (SRF) cavities.

36 MATERIALS SCIENCE↗

Removal of As(V) from wastewaters using magnetic iron oxides formed by zero-valent iron electrocoagulation

Electrocoagulation of zero-valent iron has been widely applied to the removal of dissolved arsenic, but the solid-liquid separation of arsenic-containing precipitates remains technically challenging. In this work, zero-valent iron was electrochemically oxidized to magnetic iron oxides for the removal of As(V) from simulated and actual mining wastewaters. The results indicated that lepidocrocite was formed when zero-valent iron was oxidized by dissolved oxygen, but ferrihydrite and green rust were first formed and then transformed to magnetic iron oxides (mainly magnetite and maghemite) in the electrochemical oxidation from 0 to 0.9 V (vs. SCE), which facilitates the adsorption of As(V) and subsequent solid-liquid separation under a magnetic field. In simulated As(V)-containing solution with initial pH 7.0, zero-valent iron was electrochemically oxidized to magnetite and maghemite at 0.6 V (vs. SCE) for 2 h. The As(V) concentration first decreased from 5127.5 to 26.8 μg L -1 with a removal ratio of 99.5%. In actual mining wastewaters, zero-valent iron was electrochemically oxidized to maghemite at 0.6 V (vs. SCE) for 24 h, and the As(V) concentration decreased from 5486.4 to 3.6 μg L -1 with a removal ratio of 99.9%. The removal ratio of As(V) increased slightly with increasing potential, and increased first and then decreased with increasing initial pH. Compared with that of SO 4 2- and NO 3 - , the presence of Cl - significantly enhanced the removal of As(V). This work provides a highly efficient, facile and low-cost technique for the treatment of arsenic-containing wastewaters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Degradation and fate of 2,4-dinitroanisole (DNAN) and its intermediates treated with Mg/Cu bimetal: Surface examination with XAS, DFT, and LDI-MS

In this article, a novel Mg-based bimetal reagent (Mg/Cu) was used as an enhanced reductive system to degrade insensitive munition 2,4-dinitroanisole (DNAN), a contaminant found in energetic-laden waste. Degradation of DNAN was significantly impacted by dissolved oxygen and studied in anoxic and oxic bimetal systems (i.e., purging with N 2 , air, or O 2 gas). Degradation occurred through sequential nitroreduction: first one nitro group was reduced (ortho or para) to form short-lived intermediates 2-amino-4-nitroanisole or 4-amino-2-nitroanisole (2-ANAN or 4-ANAN), and then subsequent reduction of the other nitro group formed 2,4-diaminoanisole (DAAN). The nitro-amino intermediates demonstrated regioselective reduction in the ortho position to 2-ANAN; Regioselectivity was also impacted by the anoxic/oxic environment. Under O 2 -purging DNAN degradation rate was slightly enhanced, but most notably O 2 significantly accelerated DAAN generation. DAAN also further degraded only in the oxygenated Mg/Cu system. Adsorption of DNAN byproducts to the reagent occurred regardless of anoxic/oxic condition, resulting in a partition of carbon mass between the adsorbed phase (27%-35%) and dissolved phase (59%-72%). Additional surface techniques were applied to investigate contaminant interaction with Cu. Density functional theory (DFT) calculations identified preferential adsorption structures for DNAN on Cu with binding through two O atoms of one or both nitro groups. X-ray absorption spectroscopy (XAS) measurements determined the oxidation state of catalytic metal Cu and formation of a Cu-O-N bond during treatment. Laser desorption ionization mass spectrometry (LDI-MS) measurements also identified intermediate 2-ANAN adsorbed to the bimetal surface.

54 ENVIRONMENTAL SCIENCES↗

Mineral Dissolution and Secondary Precipitation on Quartz Sand in Simulated Hanford Tank Solutions Affecting Subsurface Porosity

Highly alkaline nuclear waste solutions have been released from underground nuclear waste storage tanks and pipelines into the vadose zone at the U.S. Department of Energy’s Hanford Site in Washington, causing mineral dissolution and re-precipitation upon contact with subsurface sediments. High pH caustic NaNO3 solutions with and without dissolved Al were reacted with quartz sand through flow-through columns stepwise at 45, 51, and 89°C to simulate possible reactions between leaked nuclear waste solution and primary subsurface mineral. Upon reaction, Si was released from the dissolution of quartz sand, and nitrate-cancrinite [Na8Si6Al6O24(NO3)2] precipitated on the quartz surface as a secondary mineral phase. Both steady-state dissolution and precipitation kinetics were quantified, and quartz dissolution apparent activation energy was determined. Mineral alteration through dissolution and precipitation processes results in pore volume and structure changes in the subsurface porous media. In this study, the column porosity increased up to 40.3% in the pure dissolution column when no dissolved Al was present in the leachate, whereas up to a 26.5% porosity decrease was found in columns where both dissolution and precipitation were observed because of the presence of Al in the input solution. The porosity change was also confirmed by calculation using the dissolution and precipitation rates and mineral volume changes.

alkaline nuclear waste solution↗

Empirically assessing the potential release of rare earth elements from black shale under simulated hydraulic fracturing conditions

Rare earth elements (REEs) are economically important to modern society and the rapid growth of technologies dependent on REEs has placed considerable economic pressure on their sourcing. This study addresses whether REEs could be released as a byproduct of natural gas extraction from a series of experiments that were designed to simulate hydraulic fracturing of black shale under various pressure (25 and 27.5 MPa) and temperature (50, 90, 130 °C) conditions. The dissolved REEs in the reacted fluids displayed no propensity for the REEs to be released from black shale under high pressure and temperature conditions, a result that is consistent across the different types of fluids investigated. Overall, there was a net loss of REEs from the fluid. These changes in dissolved REEs were greatest at the moment the fluids first contacted the shale and before the high temperature and high pressure conditions were imposed, although the magnitude of these changes (10 -4 μg/g) were small compared to the magnitude of the total REE content present in the solid shale samples (10 2 μg/g). These results highlight the variability and complexity of hydraulic fracturing systems and indicate that REE may not serve as robust tracers for fracturing fluid-shale reactions. Additionally, the results suggest that significant quantities of REEs may not be byproducts of hydraulically fractured shales.

03 NATURAL GAS↗

Crystallization during processing of nuclear waste glass

In glass processing situations involving glass crystallization, various crystalline forms nucleate, grow, and dissolve, typically in a nonuniform temperature field of molten glass subjected to convection. Nuclear waste glasses are remarkable examples of multicomponent vitrified mixtures involving partial crystallization. In the glass melter, crystals form and dissolve during batch-to-glass conversion, melter processing, and product cooling. Crystals often agglomerate and sink, and they may settle at the melter bottom. Within the body of cooling glass, multiple phases crystallize in a non-uniform time-dependent temperature field. Self-organizing periodic distribution (the Liesegnang effect) is common. Various crystallization phenomena that occur in glassmaking are reviewed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Conversion of batch to molten glass, II: Dissolution of quartz particles

Quartz dissolution during the batch-to-glass conversion influences the melt viscosity and ultimately the temperature at which the glass forms. Batches to make a high-alumina borosilicate glass (formulated for the vitrification of nuclear waste) were heated as 5°C min-1 and quenched from the temperatures of 400-1200°C at 100°C intervals. As a silica source, the batches contained quartz with particles ranging from 5 to 195 µm. The content of unreacted quartz in the samples was determined with x-ray diffraction. Most of fine quartz has dissolved during the early batch reactions (at temperatures <800°C), whereas coarser quartz dissolved mostly in a continuous glass phase via diffusion. The mass-transfer coefficients were assessed from the data as functions of the initial particle sizes and the temperature. A series of batch was also tested that contained nitrated components and additions of sucrose known to accelerate melting. While sucrose addition had no discernible impact on quartz dissolution, nitrate batches melted somewhat more slowly than batches containing carbonates and hydroxides in addition to nitrates.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Monte Carlo Simulations of Coupled Diffusion and Surface Reactions during the Aqueous Corrosion of Borosilicate Glasses

Borosilicate nuclear waste glasses develop complex altered layers as a result of coupled processes such as hydrolysis of network species, condensation of Si species, and diffusion. However, diffusion has often been overlooked in Monte Carlo models of the aqueous corrosion of borosilicate glasses. Therefore, three different models for dissolved Si diffusion in the altered layer were implemented in a Monte Carlo model and evaluated for glasses in the compositional range (75-x) mol% SiO2 (12.5+x/2) mol% B2O3 and (12.5+x/2) mol% Na2O, where 0 ≤ x ≤ 20%, and corroded in static conditions at a surface-to-volume ratio of 1000 m-1. The three models considered instantaneous homogenization (M1), linear concentration gradients (M2), and concentration profiles determined by solving Fick’s 2nd law using a finite difference method (M3). Model M3 revealed that concentration profiles in the altered layer are not linear and show changes in shape and magnitude as corrosion progresses, unlike those assumed in model M2. Furthermore, model M3 showed that, for borosilicate glasses with a high forward dissolution rate compared to the diffusion rate, the gradual polymerization and densification of the altered layer is significantly delayed compared to models M1 and M2. Models M1 and M2 were found to be appropriate models only for glasses with high release rates such as simple borosilicate glasses with low ZrO2 content.

borosilicates↗

Conversion kinetics during melting of simulated nuclear waste glass feeds measured by dissolution of silica

In this work, we experimentally investigated the batch-to-glass conversion kinetics of two low-activity and two high-level nuclear waste melter feeds that represent widely different behavior during melting; tests comprised thermogravimetric analysis, the feed expansion test, evolved gas analysis, and x-ray diffraction. Our study indicates that the conversion processes, which include gas-evolving reactions, dissolution of crystalline phases, and primary foam expansion and collapse, are interconnected and influenced by the feed’s thermal history. The fraction of dissolved silica was adopted as a measure of the extent of conversion inside the cold cap—the floating layer of feed material on the top surface of the melt in an electric melter. The interface between the cold cap and the free-flowing melt below was associated with a constant fraction of dissolved silica. The estimated viscosity of glass-forming melt at this interface lies within a narrow range for the feeds studied.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Uncertainty Studies of Real Anode Surface Area in Computational Analysis for Molten Salt Electrorefining

This study examines how much cell potential changes with five differently assumed real anode surface area cases. Determining real anode surface area is a significant issue to be resolved for precisely modeling molten salt electrorefining. Based on a three-dimensional electrorefining model, calculated cell potentials compare with an experimental cell potential variation over 80 hours of operation of the Mark-IV electrorefiner with driver fuel from the Experimental Breeder Reactor II. We succeeded to achieve a good agreement with an overall trend of the experimental data with appropriate selection of a mode for real anode surface area, but there are still local inconsistencies between theoretical calculation and experimental observation. In addition, the results were validated and compared with two-dimensional results to identify possible uncertainty factors that had to be further considered in a computational electrorefining analysis. These uncertainty factors include material properties, heterogeneous material distribution, surface roughness, and current efficiency. Zirconium's abundance and complex behavior have more impact on uncertainty towards the latter period of electrorefining at given batch of fuel. The benchmark results found that anode materials would be dissolved from both axial and radial directions at least for low burn-up metallic fuels after active liquid sodium bonding was dissolved.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydrothermal Corrosion of First-Generation Dual-Purpose Coatings on Silicon Carbide for Accident-Tolerant Fuel Cladding

In this study, four different commercial coatings, TiN, Cr, CrN, and Cr/CrN (multilayer) were deposited by physical vapor deposition (PVD) on high resistivity chemical vapor deposited (CVD) SiC for the dual purpose of corrosion mitigation and fission gas hermeticity. The coatings were exposed for up to 2600 hours in flowing high temperature (288-350°C), high purity, liquid water with dissolved hydrogen (0.15-3ppm) or dissolved oxygen (1-2ppm). The Cr/CrN coatings did not adhere well and spalled quickly during exposure. In oxygenated conditions, none of the coatings were protective . CrN coatings spalled preferentially at defect sites, but reacted slowly enough in the absence of defects to potentially be chemically protective. TiN coatings fully oxidized within a few hundred hours and spalled. In hydrogen, all the coatings were chemically stable. Coating failures were identified and attributed to localized spallation, potentially related to coating defects. Coating improvements are recommended to reduce spallation and improve coating protection for future generations of dual-purpose coatings.

36 MATERIALS SCIENCE↗