Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data versions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Validation of ERS-1 environmental data products

Evaluation of the launch-version algorithms used by the European Space Agency (ESA) to derive wind field and ocean wave estimates from measurements of sensors aboard the European Remote Sensing satellite, ERS-1, has been accomplished through comparison of the derived parameters with coincident measurements made by 24 open ocean buoys maintained by the National Oceanic and Atmospheric Administration). During the period from November 1, 1991 through February 28, 1992, data bases with 577 and 485 pairs of coincident sensor/buoy wind and wave measurements were collected for the Active Microwave Instrument (AMI) and Radar Altimeter (RA) respectively. Based on these data, algorithm retrieval accuracy is estimated to be plus or minus 4 m/s for AMI wind speed, plus or minus 3 m/s for RA wind speed and plus or minus 0.6 m for RA wave height. After removing 180 degree ambiguity errors, the AMI wind direction retrieval accuracy was estimated at plus or minus 28 degrees. All of the ERS-1 wind and wave retrievals are relatively unbiased. These results should be viewed as interim since improved algorithms are under development. As final versions are implemented, additional assessments should be conducted to complete the validation.

Goodberlet, Mark A.↗
NASA NTRS1986

Performance measurements of a data link protocol

The end-to-end performance of a program implementing IEEE Std 802.2 logical link control protocol, which provides virtual circuit and datagram service and which constitutes the top sublayer of the data link layer of the reference model for Local Area Networks is studied. The measurements of relative execution times of various functions required in transferring data, over virtual circuits or as datagrams, showed that most of the program execution time is spent in a few relatively low-level functions. One of these functions performs block movement of data in memory, and two other functions provide access to various queues. Based on this result, two alternative versions of the program which move data efficiently were written and measured. In this paper the results of the study are reported and their impact on designing hardware and software systems for a network interface are discussed.

Kanakia, Hemant↗
DOE OSTI2023

EyeON

EyeON: Eye on Operational technology Software Supply Chain attacks have risen drastically over the past few years, none more well-known and impactful than the SolarWinds compromise. Criminal organizations inserted an attack vector into a specific version of the source code, giving themselves an air of credibility. Once news broke on SolarWinds, identifying compromised sites was very difficult, even knowing the culprit update. Software Bills of Materials (SBOM) have been touted as the solution to reclaiming control of your software supply chain. Deployment of SBOMs has been slow, however, due to conflicting standards, opaque storage requirements, and vendor adoption. Additionally, the path from obtaining an SBOM and securing your supply chain is unclear; how can an SBOM library be leveraged to provide insight to your attack surface? The EyeON tool, sponsored by Department of Energy Cybersecurity, Energy Security, and Emergency Response (DoE CESER), aims to address these gaps by providing an encapsulated solution to tracking which updates have been installed in an enterprise, and alerting system administrators to vulnerabilities as they become known. Similar to a virus scanner, EyeON is a command line tool to parse either a single file, nested directory structure, or filesystem. It collects data such as signature (hashes), version information, VirusTotal tags, compiler, compilation date, and code signing information. Users will anonymously submit scan data periodically to DoE CESER, who will then compile a database of known software products employed by Critical Infrastructure and broadcast alerts based on discovered flaws as they arise.

Tenzing, Wangmo↗
DOE OSTI2021

Tidal Energy Resource Characterization, Bottom Lander Measurements, Cook Inlet, AK, 2021

These datasets are from tidal resource characterization measurements collected on the Terrasond High Energy Oceanographic Mooring (THEOM) from 1 July 2021 to 30 August 2021 (60 days) in Cook Inlet, Alaska. The lander was deployed at 60.7207031 N, 151.4294998 W in ~50 m of water. The dataset contains raw and processed data from the following two instruments: 1. A Nortek Signature 500 kHz acoustic Doppler current profiler (ADCP). Data were recorded in 4 Hz in the beam coordinate system from all 5 beams. Processed data has been averaged into 5 minutes bins and converted to the East-North-Up (ENU) coordinate system. 2. A Nortek Vector acoustic Doppler velocimeter (ADV). Data were recorded at 8 Hz in the beam coordinate system. Processed data has been averaged into 5 minutes bins and converted to the Streamwise - Cross-stream - Vertical (Principal) coordinate system. Turbulence statistics were calculated from 5-minute bins, with an FFT length equal to the bin length, and saved in the processed dataset. Data was read and analyzed using the DOLfYN (version 1.0.2) python package and saved in MATLAB (.mat) and netCDF (.nc) file formats. Files containing analyzed data (".b1") were standardized using the TSDAT (version 0.4.2) python package. NetCDF files can be opened using DOLfYN (e.g., `dat = dolfyn.load(''*.nc")`) or the xarray python package (e.g. `dat = xarray.open_dataset("*.nc"). All distances are in meters (e.g., depth, range, etc), and all velocities in m/s. See the DOLfYN documentation linked in the submission, and/or the Nortek documentation for additional details.

16 TIDAL AND WAVE POWER↗
NASA NTRS2012

Small Aircraft Data Distribution System

The CARVE Small Aircraft Data Distribution System acquires the aircraft location and attitude data that is required by the various programs running on a distributed network. This system distributes the data it acquires to the data acquisition programs for inclusion in their data files. It uses UDP (User Datagram Protocol) to broadcast data over a LAN (Local Area Network) to any programs that might have a use for the data. The program is easily adaptable to acquire additional data and log that data to disk. The current version also drives displays using precision pitch and roll information to aid the pilot in maintaining a level-level attitude for radar/radiometer mapping beyond the degree available by flying visually or using a standard gyro-driven attitude indicator. The software is designed to acquire an array of data to help the mission manager make real-time decisions as to the effectiveness of the flight. This data is displayed for the mission manager and broadcast to the other experiments on the aircraft for inclusion in their data files. The program also drives real-time precision pitch and roll displays for the pilot and copilot to aid them in maintaining the desired attitude, when required, during data acquisition on mapping lines.

Chazanoff, Seth L.↗
DOE OSTI2024

High-Throughput Microstructural Characterization and Process Correlation Using Automated Electron Backscatter Diffraction

The need to optimize the processing conditions of additively manufactured (AM) metals and alloys has driven advances in throughput capabilities for material property measurements such as tensile strength or hardness. High-throughput (HT) characterization of AM metal microstructure has fallen significantly behind the pace of property measurements due to intrinsic bottlenecks associated with the artisan and labor-intensive preparation methods required to produce highly polished surfaces. This inequality in data throughput has led to a reliance on heuristics to connect process to structure or structure to properties for AM structural materials. In this study, we show a transformative approach to achieve laser powder bed fusion (LPBF) printing, HT preparation using dry electropolishing and HT electron backscatter diffraction (EBSD). This approach was used to construct a library of > 600 experimental EBSD sample sets spanning a diverse range of LPBF process conditions for AM Kovar. This vast library is far more expansive in parameter space than most state-of-the-art studies, yet it required only approximately 10 labor hours to acquire. Build geometries, surface preparation methods, and microscopy details, as well as the entire library of >600 EBSD data sets over the two sample design versions, have been shared with intent for the materials community to leverage the data and further advance the approach. Using this library, we investigated process–structure relationships and uncovered an unexpected, strong dependence of microstructure on location within the build, when varied, using otherwise identical laser parameters.

Characterization and Analytical Technique↗
NASA NTRS2005

Online Bagging and Boosting

Bagging and boosting are two of the most well-known ensemble learning methods due to their theoretical performance guarantees and strong experimental results. However, these algorithms have been used mainly in batch mode, i.e., they require the entire training set to be available at once and, in some cases, require random access to the data. In this paper, we present online versions of bagging and boosting that require only one pass through the training data. We build on previously presented work by presenting some theoretical results. We also compare the online and batch algorithms experimentally in terms of accuracy and running time.

Oza, Nikunji C.↗
NASA NTRS2015

The Quick Fire Emissions Dataset (QFED): Documentation of Versions 2.1, 2.2 and 2.4: Technical Report Series on Global Modeling and Data Assimilation - Volume 38

Biomass burning is an important source of particulates and trace gases and a major element of the terrestrial carbon cycle. Well constrained emissions from vegetation fires are needed to model direct and indirect effects of biomass burning aerosols, to model homogeneous and heterogeneous chemistry in the atmosphere, and to perform credible Earth system analysis, and climate and air pollution studies. To improve the performance of NASA Goddard Earth Observing System Model (GEOS) in the areas of atmospheric constituent modeling with a focus on biomass burning we developed the Quick Fire Emissions Dataset (QFED). The QFED emissions are based on the fire radiative power (top-down) approach and draw on the cloud correction method developed in the Global Fire Assimilation System (GFAS). Location and fire radiative power of fires are obtained from the Moderate Resolution Imaging Spectroradiometer (MODIS) Level 2 fire products (MOD14 and MYD14) and the MODIS Geolocation products (MOD03 and MYD03). QFED strengths are high spatial and temporal resolutions and near-real time availability. Daily mean emissions are available at 0.3125 times 0.25 degrees and in recent versions also at 0.1 times 0.1 degrees. QFED provides emissions of black carbon, organic carbon, sulfur dioxide, carbon monoxide, carbon dioxide, PM2.5, ammonia, nitrogen oxides, methyl ethyl ketone, propylene, ethane, propane, n- and i-butane, acetaldehyde, formaldehyde, acetone and methane. Two QFED product systems are maintained by the NASA Global Modeling and Assimilation Office (GMAO): one that produces near real-time daily emissions used operationally in the GEOS-5 Data Assimilation System, and one that produces an extended historical dataset with daily emissions from March 2000 to the present. The historical dataset also provides monthly mean and monthly climatological emissions.

Koster, Randal D.↗
DOE OSTI2024

Daily water stable isotopes, transpiration, and matrix potential data for an aspen and engelmann stand in the East River Watershed (version 2)

We provide daily stable isotope (2H & 18O) ratios in soil water and xylem (plant stem) water, as well as the sap flow (transpiration) and the soil's matric potential at a forested site near Gothic, Colorado, in the East River catchment. We measured the stable isotopic composition of the transpiration and the daily transpiration flux sum of three aspen and three engelmann spruce. In both forest stands, we installed a soil profile and measured the soil matric potential at 15, 30, and 60 cm depth as well as the stable isotopes of soil pore water at 5, 10, 30, 60, and 90 cm depths. All isotope measurements were done in situ via vapor probes connected to a cavity ring down spectrometer (Picarro L1240i).We further report the daily meteorological data observed at billy barr near our study site. We also provide for each tree the relative share of root water uptake derived from the isotope measurements via a Bayesian mixing model (MixSIAR).The daily data is provided as a time series in "Iso_MP_Sap_DataDaily_ESSDiveUpload.csv" and the units are provided in "dd.csv"; the location of the instrumented trees and soil profiles are given as latitude and longitude coordinates saved as CSV and KMZ files; and a file-level metadata (flmd.csv) file that lists each file contained in the dataset with associated metadata.The data was gathered to investigate the short-term changes of the water sources (i.e., variation of root water uptake from different soil depths) of the studied subalpine trees.Update 07/16/2025: The relative and absolute plant water uptake depths were grouped to ensure that the MixSIAR model was applied with endmembers that differed in their d2H value by at least 3 permill and at least 1 permill for d18O. Whenever the difference between observed d2H values for two or more probes at neighboring depths was less than 3 permill, we used the average value for the source water endmember. For days at which probes that were not next to each other measurements did not differ at least 3 permill, the average of all probes between these two depths was used as the water source endmember representing the depth range between these two probes.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1996

Nimbus-7 TOMS Version 7 Calibration

This report describes an improved instrument characterization used for the Version 7 processing of the Nimbus-7 Total Ozone Mapping Spectrometer (TOMS) data record. An improved internal calibration technique referred to as spectral discrimination is used to provide long-term calibration precision of +/- 1%/decade in total column ozone amount. A revised wavelength scale results in a day one calibration that agrees with other satellite and ground-based measurements of total ozone, while a wavelength independent adjustment of the initial radiometric calibration constants provides good agreement with surface reflectivity measured by other satellite-borne ultraviolet measurements. The impact of other aspects of the Nimbus-7 TOMS instrument performance are also discussed. The Version 7 data should be used in all future studies involving the Nimbus-7 TOMS measurements of ozone. The data are available through the NASA Goddard Space Flight Center's Distributive Active Archive Center (DAAC).

Wellemeyer, C. G.↗
NASA NTRSDate not supplied

On Improving the Dust Lidar Ratios for Version 5 of CALIOP by Using Measurements with Source-tagged Model Results

Vertically resolved retrievals of aerosol backscatter and extinction have been available since 2006 from global measurements acquired by the space borne lidar CALIOP onboard the CALIPSO satellite. These retrievals depend crucially upon the ratio of extinction to backscatter (i.e., lidar ratio) which typically has to be assumed for the various aerosol species for an elastic backscatter lidar like CALIOP. For all CALIPSO data releases up until now (version 4.2), these lidar ratios have been taken as constant both spatially and temporally. However, it is well established that the aerosol lidar ratios can vary significantly regionally, seasonally, and also as a function of age and relative humidity. In particular, the dust lidar ratios show significant variation depending upon their source regions, which is related to the mineral composition of dust in that region. In this paper, we shall present a scheme to obtain the regionally and seasonally dependent lidar ratios of dust. In this scheme, which may be implemented in a forthcoming version of CALIOP aerosol extinction retrievals, we first derive lidar ratios of aerosol layers globally, classified as dust by CALIOP, by using the backscatter measurements constrained by collocated MODIS aerosol optical depths. Since this dust will frequently be a mixture of dust from various source regions, we obtain the corresponding regional contributions from the dust simulations using the GEOS model tagged to nine source regions. Finally, combining information from both measurements and models, we obtain the lidar ratios of dust corresponding to the nine source regions. The lidar ratio of the mixed dust anywhere can now be obtained from the tagged model fractions and the corresponding regional lidar ratio. We shall show the application of this scheme for various regions and seasons.

CALIPSO↗
NASA NTRS1984

Documentation for the machine-readable version of the Perth 75: A Catalogue of Positions of 2589 FK4 and FK4S Stars (Nikoloff and Hog 1982)

Detailed descriptions of the data and format of the machine-readable astronomical catalog are given. The machine version is identical in data content to the published edition, but minor modifications in the data format were made in order to effect uniformity with machine versions of other astronomical catalogs. Stellar motions and positions at epoch and equinox 1950.0 are reported.

Warren, W. H., Jr.↗
NASA NTRS1998

Validation of POLDER/ADEOS data using a ground-based lidar network: Preliminary results for semi-transparent and cirrus clouds

At mid and tropical latitudes, cirrus clouds are present more than 50% of the time in satellites observations. Due to their large spatial and temporal coverage, and associated low temperatures, cirrus clouds have a major influence on the Earth-Ocean-Atmosphere energy balance through their effects on the incoming solar radiation and outgoing infrared radiation. At present the impact of cirrus clouds on climate is well recognized but remains to be asserted more precisely, for their optical and radiative properties are not very well known. In order to understand the effects of cirrus clouds on climate, their optical and radiative characteristics of these clouds need to be determined accurately at different scales in different locations i.e. latitude. Lidars are well suited to observe cirrus clouds, they can detect very thin and semi-transparent layers, and retrieve the clouds geometrical properties i.e. altitude and multilayers, as well as radiative properties i.e. optical depth, backscattering phase functions of ice crystals. Moreover the linear depolarization ratio can give information on the ice crystal shape. In addition, the data collected with an airborne version of POLDER (POLarization and Directionality of Earth Reflectances) instrument have shown that bidirectional polarized measurements can provide information on cirrus cloud microphysical properties (crystal shapes, preferred orientation in space). The spaceborne version of POLDER-1 has been flown on ADEOS-1 platform during 8 months (October 96 - June 97), and the next POLDER-2 instrument will be launched in 2000 on ADEOS-2. The POLDER-1 cloud inversion algorithms are currently under validation. For cirrus clouds, a validation based on comparisons between cloud properties retrieved from POLDER-1 data and cloud properties inferred from a ground-based lidar network is currently under consideration. We present the first results of the validation.

Chepfer, H.↗
DOE OSTI2025

High‐Resolution National‐Scale Water Modeling Is Enhanced by Multiscale Differentiable Physics‐Informed Machine Learning

Abstract The National Water Model (NWM) is a key tool for flood forecasting, planning, and water management. Key challenges facing the NWM include calibration and parameter regionalization when confronted with big data. We present two novel versions of high‐resolution (∼37 km 2 ) differentiable models (a type of hybrid model): one with implicit, unit‐hydrograph‐style routing and another with explicit Muskingum‐Cunge routing in the river network. The former predicts streamflow at basin outlets whereas the latter presents a discretized product that seamlessly covers rivers in the conterminous United States (CONUS). Both versions use neural networks to provide a multiscale parameterization and process‐based equations to provide a structural backbone, which were trained simultaneously (“end‐to‐end”) on 2,807 basins across the CONUS and evaluated on 4,997 basins. Both versions show great potential to elevate future NWM performance for extensively calibrated as well as ungauged sites: the median daily Nash‐Sutcliffe efficiency of all 4,997 basins is improved to around 0.68 from 0.48 of NWM3.0. As they resolve spatial heterogeneity, both versions greatly improved simulations in the western CONUS and also in the Prairie Pothole Region, a long‐standing modeling challenge. The Muskingum‐Cunge version further improved performance for basins >10,000 km 2 . Overall, our results show how neural‐network‐based parameterizations can improve NWM performance for providing operational flood predictions while maintaining interpretability and multivariate outputs. The modeling system supports the Basic Model Interface (BMI), which allows seamless integration with the next‐generation NWM. We also provide a CONUS‐scale hydrologic data set for further evaluation and use.

Song, Yalan [Civil and Environmental Engineering T↗
NASA NTRS2018

The Atmosphere-Ocean Interface Layer of NASA's Goddard Earth Observing System Model and Data Assimilation System Volume 51

The Goddard Earth Observing System (GEOS) general circulation model (GCM) includes modules for sea surface temperature (SST) diurnal warming and cool-skin layers. To support the application of a coupled atmosphere-ocean data assimilation capability, the GCM needs to be flexible enough to support both coupled atmosphere ocean general circulation model (AOGCM) and atmosphere-only (AGCM) configurations, with only minor configuration changes at the user interface. This document presents a formulation of an atmosphere-ocean interface layer (AOIL) that serves this purpose. Previous work by Akella et al. (2017) described a version of a model for near-surface temperature variations, including both both diurnal warming and cool-skin effects, that has been used since 2017 in the near-real-time GEOS FP (forward processing) weather analysis and forecasting system. The diurnal cycle of SST in that version of the GEOS atmospheric data assimilation system (ADAS) undergoes a sharp decay in the late afternoon (local time). The updated AOIL presented here includes a modification of the similarity function used in the diurnal warming model. Results from offline model runs illustrate an improvement in the near-surface (less than 0:5m depth) diurnal cycle compared to the original formulation. The new formulation requires minimal parameter tuning, and the improvements are robust across long (several month) simulation periods. This new model formulation, however, retains some deficiences from the previous module, such as a small warm bias in calm wind conditions for water depths below 1m. Our future work would include surface salinification and sea-ice into the AOIL.

Koster, Randal D.↗
NASA NTRS2000

A Method for Assessing the Quality of Model-Based Estimates of Ground Temperature and Atmospheric Moisture Using Satellite Data

A method is developed for validating model-based estimates of atmospheric moisture and ground temperature using satellite data. The approach relates errors in estimates of clear-sky longwave fluxes at the top of the Earth-atmosphere system to errors in geophysical parameters. The fluxes include clear-sky outgoing longwave radiation (CLR) and radiative flux in the window region between 8 and 12 microns (RadWn). The approach capitalizes on the availability of satellite estimates of CLR and RadWn and other auxiliary satellite data, and multiple global four-dimensional data assimilation (4-DDA) products. The basic methodology employs off-line forward radiative transfer calculations to generate synthetic clear-sky longwave fluxes from two different 4-DDA data sets. Simple linear regression is used to relate the clear-sky longwave flux discrepancies to discrepancies in ground temperature ((delta)T(sub g)) and broad-layer integrated atmospheric precipitable water ((delta)pw). The slopes of the regression lines define sensitivity parameters which can be exploited to help interpret mismatches between satellite observations and model-based estimates of clear-sky longwave fluxes. For illustration we analyze the discrepancies in the clear-sky longwave fluxes between an early implementation of the Goddard Earth Observing System Data Assimilation System (GEOS2) and a recent operational version of the European Centre for Medium-Range Weather Forecasts data assimilation system. The analysis of the synthetic clear-sky flux data shows that simple linear regression employing (delta)T(sub g)) and broad layer (delta)pw provides a good approximation to the full radiative transfer calculations, typically explaining more thin 90% of the 6 hourly variance in the flux differences. These simple regression relations can be inverted to "retrieve" the errors in the geophysical parameters, Uncertainties (normalized by standard deviation) in the monthly mean retrieved parameters range from 7% for (delta)T(sub g) to approx. 20% for the lower tropospheric moisture between 500 hPa and surface. The regression relationships developed from the synthetic flux data, together with CLR and RadWn observed with the Clouds and Earth Radiant Energy System instrument, ire used to assess the quality of the GEOS2 T(sub g) and pw. Results showed that the GEOS2 T(sub g) is too cold over land, and pw in upper layers is too high over the tropical oceans and too low in the lower atmosphere.

Wu, Man Li C.↗
NASA NTRS2016

Cloud-Based Orchestration of a Model-Based Power and Data Analysis Toolchain

The proposed Europa Mission concept contains many engineering and scientific instruments that consume varying amounts of power and produce varying amounts of data throughout the mission. System-level power and data usage must be well understood and analyzed to verify design requirements. Numerous cross-disciplinary tools and analysis models are used to simulate the system-level spacecraft power and data behavior. This paper addresses the problem of orchestrating a consistent set of models, tools, and data in a unified analysis toolchain when ownership is distributed among numerous domain experts. An analysis and simulation environment was developed as a way to manage the complexity of the power and data analysis toolchain and to reduce the simulation turnaround time. A system model data repository is used as the trusted store of high-level inputs and results while other remote servers are used for archival of larger data sets and for analysis tool execution. Simulation data passes through numerous domain-specific analysis tools and end-to-end simulation execution is enabled through a web-based tool. The use of a cloud-based service facilitates coordination among distributed developers and enables scalable computation and storage needs, and ensures a consistent execution environment. Configuration management is emphasized to maintain traceability between current and historical simulation runs and their corresponding versions of models, tools and data.

Post, Ethan↗
NASA NTRS1995

Millimeter-wave Imaging Radiometer (MIR) data processing and development of water vapor retrieval algorithms

This document describes the progress of the task of the Millimeter-wave Imaging Radiometer (MIR) data processing and the development of water vapor retrieval algorithms, for the second six-month performing period. Aircraft MIR data from two 1995 field experiments were collected and processed with a revised data processing software. Two revised versions of water vapor retrieval algorithm were developed, one for the execution of retrieval on a supercomputer platform, and one for using pressure as the vertical coordinate. Two implementations of incorporating products from other sensors into the water vapor retrieval system, one from the Special Sensor Microwave Imager (SSM/I), the other from the High-resolution Interferometer Sounder (HIS). Water vapor retrievals were performed for both airborne MIR data and spaceborne SSM/T-2 data, during field experiments of TOGA/COARE, CAMEX-1, and CAMEX-2. The climatology of water vapor during TOGA/COARE was examined by SSM/T-2 soundings and conventional rawinsonde.

Chang, L. Aron↗