Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Dynamical approach study of spurious steady-state numerical solutions of nonlinear differential equations. I - The dynamics of time discretization and its implications for algorithm development in computational fluid dynamics

Spurious stable as well as unstable steady state numerical solutions, spurious asymptotic numerical solutions of higher period, and even stable chaotic behavior can occur when finite difference methods are used to solve nonlinear differential equations (DE) numerically. The occurrence of spurious asymptotes is independent of whether the DE possesses a unique steady state or has additional periodic solutions and/or exhibits chaotic phenomena. The form of the nonlinear DEs and the type of numerical schemes are the determining factor. In addition, the occurrence of spurious steady states is not restricted to the time steps that are beyond the linearized stability limit of the scheme. In many instances, it can occur below the linearized stability limit. Therefore, it is essential for practitioners in computational sciences to be knowledgeable about the dynamical behavior of finite difference methods for nonlinear scalar DEs before the actual application of these methods to practical computations. It is also important to change the traditional way of thinking and practices when dealing with genuinely nonlinear problems. In the past, spurious asymptotes were observed in numerical computations but tended to be ignored because they all were assumed to lie beyond the linearized stability limits of the time step parameter delta t. As can be seen from the study, bifurcations to and from spurious asymptotic solutions and transitions to computational instability not only are highly scheme dependent and problem dependent, but also initial data and boundary condition dependent, and not limited to time steps that are beyond the linearized stability limit.

Yee, H. C.↗
NASA NTRS1992

The influence of fiber waviness on the compressive behavior of unidirectional continuous fiber composites

The influence of fiber waviness and matrix nonlinearity on the compressive behavior of continuous fiber composites is studied. A micromechanics model based on the kinematics of the fibers has been developed to predict the behavior of unidirectional composites with initially wavy fibers under compressive loads. The initial waviness has been idealized as sinusoidal. Nonlinear shear behavior of the matrix has been included. Because the shear strain in the matrix is a function of position, the deformed shape of the fibers differs from the initial shape. Therefore, the deformed fiber shape is represented by a sine series. Fiber waviness and matrix shear properties have been determined experimentally for T650-42/Radel C under several conditions. These experimental data have been used as input into the analytical model. Predicted compressive response is in reasonable agreement with experimental data.

Highsmith, Alton L.↗
NASA NTRS1984

A mathematical problem and a Spacecraft Control Laboratory Experiment (SCOLE) used to evaluate control laws for flexible spacecraft. NASA/IEEE design challenge

Discussed here is a NASA program which was initiated to make direct comparisons of control laws for a mathematical problem. An experimental test item is being assembled under the cognizance of the Spacecraft Control Branch at Langley Research Center. The physical apparatus will consist of a softly supported dynamic model of an antenna attached to the Space Shuttle by a flexible beam. The control objective will include the task of directing the line of sight of the Shuttle/antenna configuration toward a fixed target, under conditions of noisy data, limited control authority, and random disturbances.

Taylor, Lawrence W., Jr.↗
NASA NTRS1992

Review of the physical and mechanical properties and potential applications of the B2 compound NiAl: Unabridged version of a paper published in International materials review

Considerable work has been performed on NiAl over the last three decades, with an extremely rapid growth in research on this intermetallic occurring in the last few years due to recent interest in this material for electronic and high temperature structural applications. However, many physical properties and the controlling fracture and deformation mechanisms over certain temperature regimes are still in question. Part of this problem lies in the incomplete characterization of many of the alloys previously investigated. Fragmentary data on processing conditions, chemistry, microstructure and the apparent difficulty in accurately measuring composition has made direct comparison between individual studies sometimes tenuous. Therefore, the purpose of this review is to summarize all available mechanical and pertinent physical properties on NiAl, stressing the most recent investigations, in an attempt to understand the behavior of NiAl and its alloys over a broad temperature range.

Noebe, Ronald D.↗
NASA NTRS1993

Tunneling magnetic force microscopy

We have developed a powerful new tool for studying the magnetic patterns on magnetic recording media. This was accomplished by modifying a conventional scanning tunneling microscope. The fine-wire probe that is used to image surface topography was replaced with a flexible magnetic probe. Images obtained with these probes reveal both the surface topography and the magnetic structure. We have made a thorough theoretical analysis of the interaction between the probe and the magnetic fields emanating from a typical recorded surface. Quantitative data about the constituent magnetic fields can then be obtained. We have employed these techniques in studies of two of the most important issues of magnetic record: data overwrite and maximizing data-density. These studies have shown: (1) overwritten data can be retrieved under certain conditions; and (2) improvements in data-density will require new magnetic materials. In the course of these studies we have developed new techniques to analyze magnetic fields of recorded media. These studies are both theoretical and experimental and combined with the use of our magnetic force scanning tunneling microscope should lead to further breakthroughs in the field of magnetic recording.

Burke, Edward R.↗
NASA NTRS1992

Involuntary attentional capture by abrupt onsets

Five experiments were carried out to examine the extent to which brief abrupt-onset visual stimuli involuntarily capture spatial attention. A fundumantal limitation on the conscious control of spatial attention is demonstrated. Data obtained reveal conditions under which the control of spatial attention is completely involuntary: attention is captured by an irrelevant event despite subjects' intentions to ignore the event. The paradigm used provided strong incentives to ignore the distracting abrupt onset, but these were insufficient to prevent capture. Results suggest that voluntary control of attention is limited to focusing attention in advance on locations, objects, or properties of interest. Under appropriate conditions, spatial attention can be involantarily drawn to abrupt-onset events despite the intention of subjects' to ignore them.

Remington, Roger W.↗
NASA NTRS1992

Cold flow testing of the Space Shuttle Main Engine alternate turbopump development high pressure fuel turbine model

NASA's Marshall Space Flight Center has established a cold airflow turbine test program to experimentally determine the performance of liquid rocket engine turbopump drive turbines. Testing of the SSME alternate turbopump development (ATD) fuel turbine was conducted for back-to-back comparisons with the baseline SSME fuel turbine results obtained in the first quarter of 1991. Turbine performance, Reynolds number effects, and turbine diagnostics, such as stage reactions and exit swirl angles, were investigated at the turbine design point and at off-design conditions. The test data showed that the ATD fuel turbine test article was approximately 1.4 percent higher in efficiency and flowed 5.3 percent more than the baseline fuel turbine test article. This paper describes the method and results used to validate the ATD fuel turbine aerodynamic design. The results are being used to determine the ATD high pressure fuel turbopump (HPFTP) turbine performance over its operating range, anchor the SSME ATD steady-state performance model, and validate various prediction and design analyses.

Gaddis, Stephen W.↗
NASA NTRS1992

Thermal analysis of a shower-head burner

The heat transfer coefficients and convective temperatures around the spray bar of the shower-head burner in the NASA Langley Research Center High Temperature Tunnel are determined. The use of the FLUENT computer code and empirical equations in this effort is described. It is concluded that using the FLUENT code allows higher convective temperatures to be predicted than using experimental data at shutdown conditions. Empirical equations are acceptable for calculation heat-transfer coefficients.

Egoavil, Marco A.↗
NASA NTRS1958

Measurements of the Buffeting Loads on the Wing and Horizontal Tail of a 1/4-scale Model of the X-1E Airplane

The buffeting loads acting on the wing and horizontal tail of a 1/4-scale model of the X-1E airplane have been measured in the Langley 16-foot transonic tunnel in the Mach number range from 0.40 to 0.90. When the buffeting loads were reduced to a nondimensional aerodynamic coefficient of buffeting intensity, it was found that the maximum buffeting intensity of the horizontal tail was about twice as large as that of the wing. Comparison of power spectra of buffeting loads acting on the horizontal tail of the airplaneand of the model indicated that the model horizontal tail, which was of conventional force-test-model design, responded in an entirely different mode than did the airplane.This result implied that if quantitative extrapolation of model data to flight conditions were desired a dynamically scaled model of the rearward portion of the fuselage and empennage would be required. A study of the sources of horizontal-tail buffeting of the model indicated that the wing wake contributed a large part of the total buffeting load. At one condition it was found that removal of the wing wake would reduce the buffeting loads on the horizontal tail to about one-third of the original value.

Rainey, A Gerald↗
NASA NTRS1993

Cruise noise measurements of a scale model advanced ducted propulsor

A scale model Advanced Ducted Propulsor (ADP) was tested in NASA Lewis Research Center's 8- by 6-Foot Wind Tunnel to obtain acoustic data at cruise conditions. The model, designed and manufactured by Pratt & Whitney Division of United Technologies, was tested with three inlet lengths. The model has 16 rotor blades and 22 stator vanes, which results in a cut-on condition with respect to rotor-stator interaction noise. Comparisons of the noise directivity of the ADP with that of a previously tested high-speed, unducted propeller showed that the ADP peak blade passing tone was about 30 dB below that of the propeller, and therefore, should not present a cabin or enroute noise problem. The maximum blade passing tone first increased with increasing helical tip Mach number, peaked, and then decreased at a higher Mach number. The ADP tests with the shortest inlet showed more noise in the inlet arc than did tests with either of the other two inlet lengths.

Dittmar, James H.↗
NASA NTRS1993

Performance measurements and operational characteristics of the Storage Tek ACS 4400 tape library with the Cray Y-MP EL

With over 5000 units sold, the Storage Tek Automated Cartridge System (ACS) 4400 tape library is currently the most popular large automated tape library. Based on 3480/90 tape technology, the library is used as the migration device ('nearline' storage) in high-performance mass storage systems. In its maximum configuration, one ACS 4400 tape library houses sixteen 3480/3490 tape drives and is capable of holding approximately 6000 cartridge tapes. The maximum storage capacity of one library using 3480 tapes is 1.2 TB and the advertised aggregate I/O rate is about 24 MB/s. This paper reports on an extensive set of tests designed to accurately assess the performance capabilities and operational characteristics of one STK ACS 4400 tape library holding approximately 5200 cartridge tapes and configured with eight 3480 tape drives. A Cray Y-MP EL2-256 was configured as its host machine. More than 40,000 tape jobs were run in a variety of conditions to gather data in the areas of channel speed characteristics, robotics motion, time taped mounts, and timed tape reads and writes.

Hull, Gary↗
NASA NTRS1993

Physical and mechanical properties of the B2 compound NiAl

Considerable work has been performed on NiAl over the last three decades, with an extremely rapid growth in research on this intermetallic occurring in the last few years due to recent interest in this material for electronic and high temperature structural applications. However, many physical properties and the controlling fracture and deformation mechanisms over certain temperature regimes are still in question. Part of this problem lies in the incomplete characterization of many of the alloys previously investigated. Fragmentary data on processing conditions, chemistry, microstructure and the apparent difficulty in accurately measuring composition has made direct comparison between individual studies sometimes tenuous. Therefore, the purpose of this review is to summarize all available mechanical and pertinent physical properties on NiAl, stressing the most recent investigations, in an attempt to understand the behavior of NiAl and its alloys over a broad temperature range.

Noebe, R. D.↗
NASA NTRS1994

A new stochastic systems approach to structural integrity

This paper develops improved stochastic models for the description of a large variety of fatigue crack growth phenomena that occur in components of considerable importance to the functionality and reliability of complex engineering structures. In essence, the models are based on the McGill-Markov and Closure-Lognormal stochastic processes. Not only do these models have the capability of predicting the statistical dispersion of crack growth rates, they also, by incorporating the concept of crack closure, have the capability of transferring stochastic crack growth properties measured under ideal laboratory conditions to situations of industrial significance, such as those occurring under adverse loading and/or environmental conditions. The primary data required in order to be in a position to estimate the pertinent parameters of these stochastic models are obtained from a statistically significant number of replicate tests. In this paper, both the theory and the experimental technique are illustrated using a Ti-6Al-4V alloy. Finally, important structural integrity, reliability, availability and maintainability concepts are developed and illustrated.

Provan, James W.↗
NASA NTRS1995

Aerodynamic parameter estimation via Fourier modulating function techniques

Parameter estimation algorithms are developed in the frequency domain for systems modeled by input/output ordinary differential equations. The approach is based on Shinbrot's method of moment functionals utilizing Fourier based modulating functions. Assuming white measurement noises for linear multivariable system models, an adaptive weighted least squares algorithm is developed which approximates a maximum likelihood estimate and cannot be biased by unknown initial or boundary conditions in the data owing to a special property attending Shinbrot-type modulating functions. Application is made to perturbation equation modeling of the longitudinal and lateral dynamics of a high performance aircraft using flight-test data. Comparative studies are included which demonstrate potential advantages of the algorithm relative to some well established techniques for parameter identification. Deterministic least squares extensions of the approach are made to the frequency transfer function identification problem for linear systems and to the parameter identification problem for a class of nonlinear-time-varying differential system models.

Pearson, A. E.↗
NASA NTRS1994

Observations of water vapor by ground-based microwave radiometers and Raman lidar

In November to December 1991, a substantial number of remote sensors and in situ instruments were operated together in Coffeyville, Kansas, during the climate experiment First ISCCP Regional Experiment Phase 2 (FIRE 2). Includede in the suite of instruments were (1) the NOAA Environmental Technology Laboratory (ETL) three-channel microwave radiometer, (2) the NASA GSFC Raman lidar, (3) ETL radio acoustic sounding system (RASS), and (4) frequent, research-quality radiosondes. The Raman lidar operated only at night and the focus of this portion of the experiment concentrated on clear conditions. The lidar data, together with frequent radiosondes and measurements of temperature profiles (every 15 min) by RASS allowed profiles of temperature and absolute humidity to be estimated every minute. We compared 20 min measurements of brightness temperature (T(sub b) with calculations of T(sub b) that were based on the Liebe and Layton (1987) and Liebe et al. (1993) microwave propagation models, as well as the Waters (1976) model. The comparisons showed the best agreement at 20.6 GHz with the Waters model, with the Liebe et al. (1993) model being best at 31.65 GHz. The results at 90 GHz gave about equal success with the Liebe and Layton (1987) and Liebe et al. (1993) models. Comparisons of precipitable water vapor derived independently from the two instruments also showed excellent agreement, even for averages as short as 2 min. The rms difference between Raman and radiometric determinations of precipitable water vapor was 0.03 cm which is roughly 2%. The experiments clearly demonstrate the potential of simultaneous operation of radiometers and Raman lidars for fundamental physical studies of water vapor.

Han, Yong↗
NASA NTRS1994

Controlled ecological life support systems (CELSS) flight experimentation

The NASA CELSS program has the goal of developing life support systems for humans in space based on the use of higher plants. The program has supported research at universities with a primary focus of increasing the productivity of candidate crops plants. To understand the effects of the space environment on plant productivity, the CELSS Test Facility (CTF) has been conceived as an instrument that will permit the evaluation of plant productivity on Space Station Freedom. The CTF will maintain specific environmental conditions and collect data on gas exchange rates and biomass accumulation over the growth period of several crop plants grown sequentially from seed to harvest. The science requirements for the CTF will be described, as will current design concepts and specific technology requirements for operation in micro-gravity.

Kliss, M.↗
NASA NTRS1995

In-flight demonstration of a Real-Time Flush Airdata Sensing (RT-FADS) system

A prototype real-time flush airdata sensing (RT-FADS) system has been developed and flight tested at the NASA Dryden Flight Research Center. This system uses a matrix of pressure orifices on the vehicle nose to estimate airdata parameters in real time using nonlinear regression. The algorithm is robust to sensor failures and noise in the measured pressures. The RT-FADS system has been calibrated using inertial trajectory measurements that were bootstrapped for atmospheric conditions using meteorological data. Mach numbers as high as 1.6 and angles of attack greater than 45 deg have been tested. The system performance has been evaluated by comparing the RT-FADS to the ship system airdata computer measurements to give a quantitative evaluation relative to an accepted measurement standard. Nominal agreements of approximately 0.003 in Mach number and 0.20 deg in angle of attack and angle of sideslip have been achieved.

Whitmore, Stephen A.↗