Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “critical experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Flight Crew Workload, Acceptability, and Performance When Using Data Comm in a High-Density Terminal Area Simulation

This document describes a collaborative FAA/NASA experiment using 22 commercial airline pilots to determine the effect of using Data Comm to issue messages during busy, terminal area operations. Four conditions were defined that span current day to future flight deck equipage: Voice communication only, Data Comm only, Data Comm with Moving Map Display, and Data Comm with Moving Map displaying taxi route. Each condition was used in an arrival and a departure scenario at Boston Logan Airport. Of particular interest was the flight crew response to D-TAXI, the use of Data Comm by Air Traffic Control (ATC) to send taxi instructions. Quantitative data was collected on subject reaction time, flight technical error, operational errors, and eye tracking information. Questionnaires collected subjective feedback on workload, situation awareness, and acceptability to the flight crew for using Data Comm in a busy terminal area. Results showed that 95% of the Data Comm messages were responded to by the flight crew within one minute and 97% of the messages within two minutes. However, post experiment debrief comments revealed almost unanimous consensus that two minutes was a reasonable expectation for crew response. Flight crews reported that Expected D-TAXI messages were useful, and employment of these messages acceptable at all altitude bands evaluated during arrival scenarios. Results also indicate that the use of Data Comm for all evaluated message types in the terminal area was acceptable during surface operations, and during arrivals at any altitude above the Final Approach Fix, in terms of response time, workload, situation awareness, and flight technical performance. The flight crew reported the use of Data Comm as implemented in this experiment as unacceptable in two instances: in clearances to cross an active runway, and D-TAXI messages between the Final Approach Fix and 80 knots during landing roll. Critical cockpit tasks and the urgency of out-the window scan made the additional head down time to respond to Data Comm messages undesirable during these events. However, most crews also stated that Data Comm messages without an accompanying audio chime and no expectation of an immediate response could be acceptable even during these events.

Norman, R. Michael↗
NASA NTRS2021

Phase Change Processes for Thermal Management Systems and Science Investigations

This white paper focuses on the scientific rationale and motivation for deploying phase change processes-based spacecraft thermal management systems for space missions [1,2]. Phase change processes need to be implemented in the design of various life support systems, sub-critical cryogenic and thermal control systems, taking advantage of the latent heat of phase change so as to significantly increase the heat transfer rate per unit fluid mass. Experimental data are critical to understanding gravitational effects on complex phase change processes using novel materials and working fluids. Experimental data can be acquired by either designing new testing platforms or performing experiments with simulant fluids on existing microgravity platforms. With the acquired data, theoretical flow physics models and numerical simulations can then be validated for use under long-duration microgravity conditions. The acquired data and validated models will enable the deployment of game-changing thermal management systems with remarkably improved efficiency and stability in heat acquisition, transport, and rejection for long-duration space missions.

Fluid mechanics↗
NASA NTRS2010

Preliminary Results of Bisphosphonate ISS Flight Experiment

Bone loss has been recognized as a potential problem from the beginning of human spaceflight. With the spaceflight missions lasting 6 months to potentially 3 years or longer this issue has assumed increased significance. Detailed measurements from the Mir and ISS long duration missions have documented losses in bone mineral density (BMD) from the total skeleton and critical sub-regions. The most important losses are from the femoral hip averaging about -1.6%/mo integral to -2.3%/mo trabecular BMD. Importantly these studies have documented the wide range in individual response from -0.5 to -5%/mo in BMD. Given the small size of any expedition crew, the wide range of responses has to be considered in the implementation of any countermeasure. Assuming that it is unlikely that the susceptibility for bone loss in any given crewmember will be known, a suite of bone loss countermeasures will likely be needed to insure protection of all crewmembers. The hypothesis for this experiment is that the combined effect of anti-resorptive drugs plus the standard in-flight exercise regimen will have a measurable effect on preventing space flight induced bone loss and strength and will reduce renal stone risk. To date, 4 crewmembers have completed the flight portion of the protocol in which crewmembers take a 70-mg alendronate tablet once a week before and during flight, starting 17 days before launch. Compared to previous ISS crewmembers (n=14) not taking alendronate, DXA measurements of the total hip BMD were significantly changed from -1.1 0.5%/mo to 0.04 0.3%/mo (p<0.01); QCT-determined trabecular BMD of the total hip was significantly changed from -2.3 1.0%/mo to -0.3 1.6%/mo (p<0.01). Significance was calculated from a one-tailed t test. While these results are encouraging, the current n (4) is small, and the large SDs indicate that while the means are improved there is still high variability in individual response. Four additional crewmembers have been recruited to participate in this experiment, with expected completion of these flights by late 2011.

LeBlanc, Adrian↗
NASA NTRS2013

International R&M/Safety Cooperation Lessons Learned Between NASA and JAXA

Presented are a number of important experiences gained and lessons learned from the collaboration of the National Aeronautics and Space Administration (NASA) and the Japanese Aerospace Exploration Agency (JAXA) on the CoNNeCT (Communications, Navigation, and Networking re-Configurable Testbed) project. Both space agencies worked on the CoNNeCT Project to design, assemble, test, integrate, and launch a communications testbed facility mounted onto the International Space Station (ISS) truss. At the 2012 RAMS, two papers about CoNNeCT were presented: one on Ground Support Equipment Reliability & System Safety, and the other one on combined application of System Safety & Reliability for the flight system. In addition to the logistics challenges present when two organizations are on the opposite side of the world, there is also a language barrier. The language barrier encompasses not only the different alphabet, it encompasses the social interactions; these were addressed by techniques presented in the paper. The differences in interpretation and application of Spaceflight Requirements will be discussed in this paper. Although many, but definitely not all, of JAXA's Spaceflight Requirements were inspired by NASA, there were significant and critically important differences in how they were interpreted and applied. This paper intends to summarize which practices worked and which did not for an international collaborative effort so that future missions may benefit from our experiences. The CoNNeCT flight system has been successfully assembled, integrated, tested, shipped, launched and installed on the ISS without incident. This demonstrates that the steps taken to facilitate international understanding, communication, and coordination were successful and warrant discussion as lessons learned.

Fernandez, Rene↗
NASA NTRS2017

Strategic Employee Development in The Government Sector

As with many other U.S. agencies, succession planning is becoming a critical need for NASA. The primary drivers include (a) NASA's higher-than-average aged workforce with approximately 50% of employees eligible for retirement within 5 years; and (b) employees who need better developmental conversations to increase morale and retention. This problem is particularly concerning for Safety & Mission Assurance (S&MA) organizations since they traditionally rely on more experienced engineers and specialists to perform their organizations' functions. In response to this challenge, the Kennedy Space Center (KSC) S&MA organization created the Strategic Employee Development (SED) program. The SED program's goal is to provide a proactive method to counter the primary drivers by creating a deeper "bench strength" and providing a more comprehensive developmental feedback experience for the employee. The SED is a new succession planning framework that enables customization to any organization, and in this case, specifically for an S&MA organization. This is accomplished via the identification of key positions, the corresponding critical competencies, and a process to help managers have relevant and meaningful development conversations with the workforce. As a result of the SED, several tools and products were created that allows management to make better strategic workforce decisions. Although there are opportunities for improvement for the SED program, the most important impact has been on the quality of developmental discussions for employees.

Nguyen, Johnny↗
NASA NTRS1989

Spacecraft contamination experience

Effective contamination control must encompass all aspects of ground and flight from design of the system through the end of mission life. Design systems are needed to minimize sensitivity to contamination, ease of cleaning, and contaminant production. Facilities and procedures are critical to maintaining cleanliness during ground operations. Flight operations should be planned so as to minimize contamination. More data from flights are required to assess the adequacy of designs and operations. Standards and specifications should include contamination control requirements.

Borson, E. N.↗
NASA NTRS1996

Ambient mass density effects on the International Space Station (ISS) microgravity experiments

The Marshall engineering thermosphere model was specified by NASA to be used in the design, development and testing phases of the International Space Station (ISS). The mass density is the atmospheric parameter which most affects the ISS. Under simplifying assumptions, the critical ambient neutral density required to produce one micro-g on the ISS is estimated using an atmospheric drag acceleration equation. Examples are presented for the critical density versus altitude, and for the critical density that is exceeded at least once a month and once per orbit during periods of low and high solar activity. An analysis of the ISS orbital decay is presented.

Smith, O. E.↗
NASA NTRS2017

Quantifying Pilot Contribution to Flight Safety during Drive Shaft Failure

Accident statistics cite the flight crew as a causal factor in over 60% of large transport aircraft fatal accidents. Yet, a well-trained and well-qualified pilot is acknowledged as the critical center point of aircraft systems safety and an integral safety component of the entire commercial aviation system. The latter statement, while generally accepted, cannot be verified because little or no quantitative data exists on how and how many accidents/incidents are averted by crew actions. A joint NASA/FAA high-fidelity motion-base simulation experiment specifically addressed this void by collecting data to quantify the human (pilot) contribution to safety-of-flight and the methods they use in today's National Airspace System. A human-in-the-loop test was conducted using the FAA's Oklahoma City Flight Simulation Branch Level D-certified B-737-800 simulator to evaluate the pilot's contribution to safety-of-flight during routine air carrier flight operations and in response to aircraft system failures. These data are fundamental to and critical for the design and development of future increasingly autonomous systems that can better support the human in the cockpit. Eighteen U.S. airline crews flew various normal and non-normal procedures over a two-day period and their actions were recorded in response to failures. To quantify the human's contribution to safety of flight, crew complement was used as the experiment independent variable in a between-subjects design. Pilot actions and performance during single pilot and reduced crew operations were measured for comparison against the normal two-crew complement during normal and non-normal situations. This paper details the crew's actions, including decision-making, and responses while dealing with a drive shaft failure - one of 6 non-normal events that were simulated in this experiment.

Kramer, Lynda J.↗
NASA NTRS1998

Data Link Performance Analysis for LVLASO Experiments

Low-visibility Landing and Surface Operations System (LVLASO) is currently being prototyped and tested at NASA Langley Research Center. Since the main objective of the system is to maintain the aircraft landings and take-offs even during low-visibility conditions, timely exchange of positional and other information between the aircraft and the ground control is critical. For safety and reliability reasons, there are several redundant sources on the ground (e.g., ASDE, AMASS) that collect and disseminate information about the environment to the aircrafts. The data link subsystem of LVLASO is responsible for supporting the timely transfer of information between the aircrafts and the ground controllers. In fact, if not properly designed, the data link subsystem could become a bottleneck in the proper functioning of LVLASO. Currently, the other components of the system are being designed assuming that the data link has adequate capacity and is capable of delivering the information in a timely manner. During August 1-28, 1997, several flight experiments were conducted to test the prototypes of subsystems developed under LVLASO project, The back-round and details of the tests are described in the next section. The test results have been collected in two CDs by FAA and Rockwell-Collins. Under the current grant, we have analyzed the data and evaluated the performance of the Mode S datalink. In this report, we summarize the results of our analysis. Much of the results are shown in terms of graphs or histograms. The test date (or experiment number) was often taken as the X-axis and the Y-axis denotes whatever metric of focus in that chart. In interpreting these charts, one need to take into account the vehicular traffic during a particular experiment. In general, the performance of the data link was found to be quite satisfactory in terms of delivering long and short Mode S squitters from the vehicles to the ground receiver, Similarly, its performance in delivering control messages from the ground control to the vehicles (aircrafts) was also satisfactory. The report is organized as follows. In Section 2, we describe the background information for the LVLASO and the system flight experiments. Section 3 contains formats of the performance data that was analyzed during our research. Section 4 describes different experiments flight experiments and their setup. Section 5 analyzes each of the graphs produced in this report. Finally, Section 6 has a summary of observations that we make based on our research.

Mukkamala, Ravi↗
NASA NTRS2015

Demonstrating Autonomous Mission Operations Onboard the International Space Station

The NASA Autonomous Mission Operations (AMO) project conducted an experiment to turn over operation and management of selected International Space Station (ISS) sys- tems to the on-board crew. ISS crews managed two different spacecraft systems: the Total Organic Carbon Analyzer (TOCA), a water quality analyzer, and Station Support Com- puters (SSC) laptops, which are non-critical crew computer systems. These systems were selected because they are representative of systems a future crew may need to operate au- tonomously during a deep space mission. The crew autonomously operated these systems, taking on mission operations functions traditionally performed by support teams on the ground, using new software tools that provide decision support algorithms for planning, monitoring and fault management, hardware schematics, system briefs, and data displays that are normally unavailable to the crew. The experiment lasted seven months, during which ISS crews managed TOCA and SSCs on 22 occasions. The AMO software processed data from TOCA and SSCs continuously during this seven month period. The combined performance of the software and crew achieved a 88 success rate on managing TOCA activity, the system for which ground-truth was available.

Autonomous Mission Operations↗
NASA NTRS1980

Information measures in nonlinear experimental design

Some different approaches to the problem of designing experiments which estimate the parameters of nonlinear models are discussed. The assumption in these approaches that the information in a set of data can be represented by a scalar is criticized, and the nonscalar discrimination information is proposed as the proper measure to use. The two-step decay example in Box and Lucas (1959) is used to illustrate the main points of the discussion.

Niple, E.↗
NASA NTRS1981

Experimental and analytical investigation of a fluidic power generator

A combined experimental and analytical investigation was performed to understand the various fluid processes associated with the conversion of flow energy into electric power in a fluidic generator. Experiments were performed under flight-simulated laboratory conditions and results were compared with those obtained in the free-flight conditions. It is concluded that the mean mass flow critically controlled the output of the fluidic generator. Cross-correlation of the outputs of transducer data indicate the presence of a standing wave in the tube; the mechanism of oscillation is an acoustic resonance tube phenomenon. A linearized model was constructed coupling the flow behavior of the jet, the jet-layer, the tube, the cavity, and the holes of the fluidic generator. The analytical results also show that the mode of the fluidic power generator is an acoustical resonance phenomenon with the frequency of operation given by f approx = a/4L, where f is the frequency of jet swallowing, a is the average speed of sound in the tube, and L is the length of the tube. Analytical results further indicated that oscillations in the fluidic generator are always damped and consequently there is a forcing of the system in operation.

Sarohia, V.↗
NASA NTRS1983

The evolution of clusters of galaxies. I - Very rich clusters

A multiple one-body Monte Carlo code is used to investigate the evolution of galaxies in a steady cluster potential under the influence of dynamical friction, two-body relaxation, tidal stripping, and galaxy mergers. The basic assumptions, estimated time scales, method and computer program, and effects of uncertainties in galaxy encounter physics are addressed. Numerical experiments in which the mass initially carried by galaxies and the mass function are varied are reported. It is shown that the formation of a very massive cluster galaxy depends critically on the number of galaxies, the initial division of cluster material between galaxies and a smooth intracluster medium, the mass spectrum of the galaxies, and chance. By the end of all simulations, less than half of the mass in the central regions of the cluster is bound to galaxies. It appears possible to produce any of the Bautz-Morgan classes from very similar initial conditions.

Richstone, D. O.↗
NASA NTRS1985

Buoyancy Effects upon Vapor Flame and Explosion Processes

The objective of this microgravity project is to develop an experimental and theoretical analyses critical to the understanding of the coupling of buoyancy and turbulence generation and its effect on fuel-air mixing, flame intensity and flame propagation in jet diffusion flames. The experiment is designed to examine certain effects of buoyancy acting on a diffusion flame in which the flame is directed either upward or downward. This change from negative to positive g is observed to significantly alter the flame shape although all other operating conditions are the same for both configurations. However, to perform this experiment a significant coaxial secondary air flow is needed in order to prevent flow reversal when the flame is inverted. The theoretical analysis that has been developed handles the secondary air flow and the extreme change in gravity vector direction. Thus the data will provide a measure of credibility of the analysis which will then be used to assist in the design of the actual zero-g experiment.

Edelman, R. B.↗
NASA NTRS1986

Spacelab 2 - Science in orbit

The success of Spacelab 2 is examined critically. Particular attention is given to the solar telescopes which were mounted on the instrument pointing system; these were designed to study solar irradiance, coronal helium, and exploding granules. Plasma experiments and the cosmic ray experiment (the 'Chicago Egg') are also described.

Page, T. L.↗
NASA NTRS1988

Strategy for D/He-3 fusion development

It is concluded that Deuterium/Helium-3 fusion faces a more difficult physics development path but an easier technology development path than does Deuterium/Tritium. Early D/He-3 tests in next generation D/T fusion experiments might provide a valuable D/He-3 proof-of-principle at modest cost. At least one high leverage alternate concept should be vigorously pursued. Space applications of D/He-3 fusion are critically important to large scale development.

Santarius, John F.↗
NASA NTRS1992

Electronic and total energy properties of ternary and quaternary semiconductor compounds, alloys, and superlattices: Theoretical study of Cu/graphite bonding

The goals of the research were to provide a fundamental science basis for why the bonding of Cu to graphite is weak, to critically evaluate the previous analysis of the wetting studies with particular regard to the values used for the surface energies of Cu and graphite, and to make recommendations for future experiments or other studies which could advance the understanding and solution of this technological problem. First principles electronic structure calculations were used to study the problem. These are based on density functional theory in the local density approximation and the use of the linear muffin-tin orbital band structure method. Calculations were performed for graphite monolayers, single crystal graphite with the hexagonal AB stacking, bulk Cu, Cu(111) surface, and Cu/graphite superlattices. The study is limited to the basal plane of graphite because this is the graphite plane exposed to Cu and graphite surface energies and combined with the measured contact angles to evaluate the experimental adhesion energy.

Lambrecht, Walter R. L.↗
NASA NTRS1992

Prompt ionization in the CRIT II barium releases

Observations of electron and ion distributions inside a fast neutral barium jet in the ionosphere show significant fluxes within 4 km of release, presumably related to beam plasma instability processes involved in the Critical Ionization Velocity (CIV) effect. Electron fluxes exceeding 5 x 10 exp 12/sq cm-str-sec-keV were responsible for ionizing both the streaming barium and ambient oxygen. Resulting ion fluxes seem to be consistent with 1-2 percent ionization of the fast barium, as reported by optical observations, although the extended spatial distribution of the optically observed ions is difficult to reconcile with the in situ observations. When the perpendicular velocity of the neutrals falls below critical values, these processes shut off. Although these observations resemble the earlier Porcupine experimental results (Haerendel, 1982), theoretical understanding of the differences between these data and that of earlier negative experiments is still lacking.

Torbert, R. B.↗