Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compositional analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Quantitative Analysis and Prediction of Thermal Runaway Metrics of High-Nickel Oxide Cathodes by Machine Learning Models

The pursuit of higher energy density in lithium-ion batteries has made high-nickel (Ni) layered oxides leading cathode candidates for next-generation electric vehicles. However, their poor thermal stability, particularly at Ni contents ≥ 90%, increases the risk of cathode-initiated thermal runaway. Furthermore, we present a data-driven framework combining linear and nonlinear machine learning models to predict key thermal runaway descriptors from a high-throughput differential scanning calorimetry database. With cathode composition and state of charge (SOC) as input features, the ensemble model accurately predicts peak temperature, heat release, and peak heat flow. SHAP analysis identifies Ni content and SOC as the dominant factors controlling thermal runaway temperature, while SOC primarily governs heat release and peak heat flow. Al, Mg, and Mn improve thermal stability by strengthening metal–oxygen bonding and delaying structural transformation, whereas B mainly reduces heat release through surface passivation. Validation with a new cathode composition confirms accurate prediction of SOC-dependent thermal runaway behavior and critical SOC.

25 ENERGY STORAGE↗
DOE OSTI2021

Operating Stresses and Their Effects on Degradation of LSM-Based SOFC Cathodes

The performance of solid oxides fuel cells (SOFCs) with four different Mn excess of lanthanum strontium manganite (LSM) -based cathodes were examined under different temperatures (1,000 °C, 900 °C), current densities (0, 380, and 760 mA cm -2 ), and cathode atmospheres (p O 2 )=0.1,0.15,0.21) for durations ranging from 58 to 1,008 h. Each yttria-stabilized zirconia (YSZ) electrolyte-supported “button” cell had a porous Ni/YSZ composite anode and a porous LSM/YSZ composite cathode. The cells’ output voltage versus time were recorded and electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) measurements were performed every 24 hours. The total area specific resistance (ASR) was calculated from these measurements. The values of ASR from both EIS and LSV were comparable between each other but lower than that from durability test. Distribution of relaxation times (DRT) analysis was performed to investigate the electrochemical processes and their corresponding relaxation frequencies as well as their attributions to the total ASR. The series resistance and parallel resistance that obtained from the equivalent circuit fit of the Nyquist plot were higher at low temperature and low p O 2 regardless of LSM compositions. The area of the peaks derived from DRT analysis increased with time during individual tests. The microstructures of the tested cells were examined using scanning electron microscopy and energy-dispersive x-ray spectroscopy (SEM/EDS). Manganese oxide particles were observed near the cathode-electrolyte interface after prolonged (1,008 h) testing in air of a cell with LSM of 11% manganese excess, and after a short test (58 h) under low oxygen (p O 2 = 0.10) in a cell with LSM of 5% manganese excess. However, the role of MnOx in cell degradation is still unknown.

08 HYDROGEN↗
DOE OSTI2025

Chemical imaging of individual stratospheric particles sampled over North America

The increasing size, severity, and frequency of wildfires have led to dramatic increases in particulate matter concentrations in the troposphere. Severe wildfires can generate intense convective systems capable of transporting large quantities of biomass burning organic aerosols (BBOA) to the upper troposphere and lower stratosphere (UTLS). Chemically complex organic matter and light-absorbing carbonaceous material is introduced into stratospheric regions that were historically isolated from direct surface emissions. In this study, stratospheric particles were sampled over North America during the Dynamics and Chemistry of the Summer Stratosphere (DCOTSS) campaign, an aircraft-based research project designed to characterize convective perturbation in the UTLS. Particle samples collected from six research flights during summer 2022 were analyzed using Computer-Controlled Scanning Electron Microscopy and Scanning Transmission X-ray Microscopy to investigate particle size distributions, morphology, chemical composition, and mixing state of stratospheric particles along transects across the continental United States and adjacent Pacific Ocean airspace. Analysis revealed that all sampled particles contained detectable levels of carbon, with most exhibiting organic volume fractions of 0.37 ± 0.20. Notably, about 5% of the particles also contained soot inclusions, which indicates the presence of refractory black carbon transported to stratospheric altitudes and provides direct evidence of wildfire-derived black carbon reaching the UTLS. Typical particle morphology exhibits organic shells over soot and inorganic cores and suggests secondary processing and aging of BBOA during transport to and within the UTLS. These findings provide compelling evidence that wildfire emissions play a critical role in affecting the long-term composition and radiative properties of stratospheric particles.

Sharpe, Steven [Purdue Univ., West Lafayette, IN (↗
DOE OSTI2023

High-Throughput Automated Exploration of Phase Growth Behaviors in Quasi-2D Formamidinium Metal Halide Perovskites

Quasi-2D metal halide perovskites (MHPs) are an emerging material platform for sustainable functional optoelectronics, but the uncontrollable, broad phase distribution remains a critical challenge for applications. Nevertheless, the basic principles for controlling phases in quasi-2D MHPs remain poorly understood, due to the rapid crystallization kinetics during the conventional thin-film fabrication process. In this work, a high-throughput automated synthesis-characterization-analysis workflow is implemented to accelerate material exploration in formamidinium (FA)-based quasi-2D MHP compositional space, revealing the early-stage phase growth behaviors fundamentally determining the phase distributions. Upon comprehensive exploration with varying synthesis conditions including 2D:3D composition ratios, antisolvent injection rates, and temperatures in an automated synthesis-characterization platform, it is observed that the prominent n = 2 2D phase restricts the growth kinetics of 3D-like phases—α-FAPbI 3 MHPs with spacer-coordinated surface—across the MHP compositions. Thermal annealing is a critical step for proper phase growth, although it can lead to the emergence of unwanted local PbI 2 crystallites. Additionally, fundamental insights into the precursor chemistry associated with spacer-solvent interaction determining the quasi-2D MHP morphologies and microstructures are demonstrated. The high-throughput study provides comprehensive insights into the fundamental principles in quasi-2D MHP phase control, enabling new control of the functionalities in complex materials systems for sustainable device applications.

2D perovskites↗
DOE OSTI2026

Heat Transfer Fluids as Co‐Diluents in Localized High‐Concentration Electrolytes for High‐Rate Lithium Metal Batteries With Enhanced Safety

Localized high-concentration electrolytes (LHCEs) have been identified as promising electrolyte formulations for lithium metal batteries, due to their effective interphase formation and promotion of compact Li deposition, yet their practical implementation is often limited by reduced ion transport kinetics. In this study, two industrially established fluorinated ethers are identified for the first time in battery research as effective co-diluents as they combine a broad electrochemical stability window with a low viscosity and intrinsic non-flammability. Incorporating these components, commonly used as heat transfer fluids, yields safer, less flammable electrolyte formulations with enhanced ion mobilities. In particular, the ternary co-diluent formulation shows improved ion mobility by reducing the electrolyte's viscosity while limiting excessive ion clustering. Based on the improved electrolyte transport kinetics, lower overvoltages and higher Coulombic efficiencies at current densities ≥ 1 mA cm −2 are achieved with the ternary co-diluent blend, resulting in markedly extended cycle life in an application-oriented zero-excess pouch cell compared with the baseline system. Complementary electrochemical and ex situ analysis of harvested electrodes at moderate current densities reveals no discernible differences in interphase morphology and composition, suggesting enhanced ion mobility as the primary cause of the improved high-rate performance.

electrolyte diluent↗
DOE OSTI2023

Using defects as a ‘fossil record’ to help interpret complex processes during additive manufacturing: as applied to raster-scanned electron beam powder bed additively manufactured Ti–6Al–4V

Abstract Defects in parts produced by additive manufacturing, instead of simply being perceived as deleterious, can act as important sources of information associated with the complex physical processes that occur during materials deposition and subsequent thermal cycles. Indeed, they act as materials-state ‘fossil’ records of the dynamic AM process. The approach of using defects as epoch-like records of prior history has been developed while studying additively manufactured Ti–6Al–4V and has given new insights into processes that may otherwise remain either obscured or unquantified. Analogous to ‘epochs,’ the evolution of these defects often is characterized by physics that span across a temporal length scale. To demonstrate this approach, a broad range of analyses including optical and electron microscopy, X-ray computed tomography, energy-dispersive spectroscopy, and electron backscatter diffraction have been used to characterize a raster-scanned electron beam Ti–6Al–4V sample. These analysis techniques provide key characteristics of defects such as their morphology, location within the part, complex compositional fields interacting with the defects, and structures on the free surfaces of defects. Observed defects have been classified as banding, spherical porosity, and lack of fusion. Banding is directly related to preferential evaporation of Al, which has an influence on mechanical properties. Lack-of-fusion defects can be used to understand columnar grain growth, fluid flow of melt pools, humping, and spattering events. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2021

Data Science Techniques, Assumptions, and Challenges in Alloy Clustering and Property Prediction

Data analytics methods have been increasingly applied to understanding materials chemistry, processing due to the manufacturing approach, and uni-axial and cyclic property relationships in the highly complex space of alloy design. There are several benefits to applying data analytics to this space, including the ability to manage non-linearities in the responses of the alloy attributes and the resulting mechanical properties. However, key difficulties in applying and understanding the results of data analytics include the often lack of reported assumptions and data processing steps necessary to improve interpretation and reproducibility in derived results. In this work, the methods used to generate clustering and correlation analyses for experimental 9% Cr ferritic-martensitic steel data were investigated and the resulting implications for mechanical property predictions were assessed. This work uses principal component analysis, partitioning around medoids, t-SNE, and k-means clustering to investigate trends in composition, processing and microstructure information with creep and tensile properties, building on work done previously using a smaller version of the same dataset. The initial assumptions, preprocessing steps and methods are investigated and outlined in order to depict the fine level of detail required to convey the steps taken to process data and produce analytical results. Here, the variations in the resulting analyses are explored due to the influence of new and more varied data.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Understanding Asteroid 16 Psyche’s composition through 3D impact crater modeling

Asteroid 16 Psyche is the largest M-type (metallic) Main Belt Asteroid (MBA). Radar albedo data indicate Psyche’s surface is rich in metallic content, but estimates for Psyche’s bulk structure vary widely, with bulk density estimates ranging from 1.4 ± 0.3 g/cm 3 to 4.5 ± 1.4 g/cm 3 and porosity estimates ranging from 30% to 70%. A forthcoming NASA discovery mission will visit Psyche. Narrowing the range of estimated compositions of Psyche prior to mission launch can help to determine the necessary tools for asteroid analysis. Psyche has two large impact structures in its Southern hemisphere, with estimated diameters from 50 km to 70 km and estimated depths up to 6.4 km. In this work, we present results from 2D and 3D hydrocode simulations of the largest of these impact structures. Through quantitative comparison of the simulated crater dimensions with measured values, our models suggest that Psyche is largely composed of porous, metallic material. In addition, to match the crater dimensions, our simulations indicate that the angle of impact was significantly altered from vertical by 45–60 degrees.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Development and performance of INCONEL® alloy 740H® seam-welded piping

INCONEL® alloy 740H® is an age-hardenable nickel-based alloy approved for pressure vessels and piping within ASME Section I, VIII, and B31.1. Currently, the code applies a weld strength reduction factor (WSRF) of 0.7 to the allowable stresses for longitudinal seam welds in the time dependent creep regime. In this work, a full-scale seam weld was successfully produced using typical industrial practices. The component was solution heat-treated and aged after fabrication to improve the performance of the weldment. Tensile, bend, impact, and low-cycle fatigue tests showed the component met all the specification requirements and elevated temperature properties were within base metal expectations with failures predominately in the weld metal. Long-term creep tests, including large samples more representative of the entire weldment, were fabricated and tested to times in excess of 10,000 h at multiple temperatures. Analysis of the creep data supports a WSRF of 0.9 for the solution annealed + aged weldments in contrast to the WSRF of 0.7 currently applied to welded + aged weldments. Metallurgical analysis shows that the solution annealing causes recrystallization of the weld metal and reduces the chemical compositional and microstructural gradients in the weldments resulting in acceptable short-term performance. In long-term creep, evidence for coarsened zones in the weldments due to discontinuous coarsening reactions were identified as the mechanism leading to accelerated creep damage formation in the weld metal and sample failure.

14 SOLAR ENERGY↗
DOE OSTI2025

Raman spectroscopic investigation of UCl 4

Uranium chloride salts are a proposed fuel source for molten salt reactors (MSRs). However, despite their relevance to nuclear energy, they remain understudied, in part because of their air and moisture sensitivity. Here, this work provides the first Raman spectra of UCl 4 from 45 to 3200 cm −1 collected with 532 and 785 nm excitation sources as well as the assignment of 10 identified peaks to their respective vibrational modes. These Raman bands are compared to those for isostructural ThCl 4 , the compositionally related UCl 3 , and the computed Raman bands for UCl 4 from local vibrational mode analysis. The observed spectrum of UCl 4 is in accord with that of ThCl 4 and the computed spectra of UCl 4 . We posit that the observed differences between the spectra of UCl 4 and UCl 3 are useful in differentiating these species for applications such as in situ monitoring of MSR operations.

Anoxic spectroscopy↗
DOE OSTI2020

Deformation behavior of metallic glass composites and plasticity accommodation at microstructural length-scales

Bulk metallic glass matrix composites represent a unique microstructural design strategy for overcoming the strength/ductility trade-off in structural alloys. Site-specific mechanical behavior of a Ti-based bulk metallic glass composite was evaluated at microstructural length-scale. The micro-pillars on the amorphous matrix showed on average a yield point of 1.9 GPa followed by serrated plastic deformation characteristic of shear banding. In contrast, micro-pillars on the crystalline dendritic phase showed a much lower yield strength of 0.72 GPa on average for the four different crystallographic orientations chosen, smooth plastic flow with no recognizable load burst, and stable strain-hardening after yield point. A number of micro-pillars were made at the interface between the glassy matrix and the crystalline dendrite. The mixed micro-pillars showed homogeneous deformation and greater plasticity which was attributed to their smaller stored elastic energy. Shear bands initiated in the amorphous matrix were arrested by the crystalline dendrite, which accommodated plasticity through slip bands and dislocations pile-ups. The interface remained intact after plastic deformation, with no observable signs of devitrification in the amorphous phase.

Bulk metallic glass matrix composite, Micro-pillar↗
DOE OSTI2020

Computational study of the adsorption of bimetallic clusters on alumina substrate

We performed computational investigation of the adsorption of bimetallic Pd 3 M 2 (where M changes from Ag, Au, Co, Cu, Mn, Ni, Pt, and Ru) cluster on the hydroxylated alumina surface. Previously, it was shown that small silver cluster can control the rate of discharge at the cathode of lithium-oxygen battery. The gap near the fermi energy was shown to control the oxygen reduction, an important reaction for LiO 2 formation. Controlling the gap would ultimately control the rate of LiO 2 formation. One can vary the size of the cluster to vary the gap, however, this "knob" provides limited variance in the gap. Alloying, in combination with size variation offer a much wider control of the gap, hence the LiO 2 formation. Using Density Functional Theory (DFT), we determined the most stable geometry of the bimetallic clusters Pd 3 M 2 and calculated the binding energies of these clusters on the alumina substrate which ranges from 0.2 eV to 0.25 eV depending upon the composition of the alloy-cluster, its orientation and the adsorption site. We also find that Pd atoms bind strongly with the substrate oxygen atoms with an average short bond-length of about 2.2 angstrom. We explored how the gap at the Fermi level of the system varies as a function of elemental composition and the calculated gap ranges from 0 meV to 90 meV. Charges distribution using Bader analysis was also performed to probe how charges are transferred between the cluster and the substrate. These preliminary results will open the door for more systematic studies of alloy clusters of different size and stoichiometry for Li-O 2 battery cathode design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Colloidal Synthesis of Single-Layer Quasi-Ruddlesden–Popper Phase Bismuth-Based Two-Dimensional Perovskite Nanosheets with Controllable Optoelectronic Properties

Single- and few-layered two-dimensional (2D) nanomaterials have attracted intense research interest in the last two decades due to their unique electronic and optoelectronic properties leading to various potential applications. Herein, we report the colloidal synthesis of Bi-based 2D perovskite nanosheets (PEG6-NH 3 +) n Cs 3-n Bi 2 X 9 , where X = CI, Br, and I, through careful design of reaction conditions and selection of poly(ethylene glycol) (PEG6) surface passivating ligands. The 2D nanosheets are similar to 5 nm in thickness with micron-sized lateral dimensions and display composition-dependent band gap and work function modulation. Furthermore, small-angle X-ray scattering analysis substantiates that the individual inorganic crystal layer, Cs 3-n Bi 2 X 9 , is separated by the spacer, PEG6 ligand. Additionally, we determined that PEG6-NH 2 is an essential passivating ligand and spacer for the formation of Bi-based 2D nanosheets. Most importantly, controlled crystallization of the colloidal dispersion of nanosheets results in the formation of superlattice microstructures of the quasi-Ruddlesden-Popper phase. These microstructures can be exfoliated to ultrathin nanosheets by overcoming the van der Waals interaction between the organic passivating layers. The controlled synthesis of lead-free 2D perovskite nanosheets presented here can expand their utility to photocatalytic and optoelectronic applications with reduced toxicity.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Solving the “Coloring Problem” in InPd 3– x Ag x ( x = 0–0.7) by Phase Diagrams Modeling and Diffraction Experiments

Here, a series of InPd 3–x Ag x (x = 0–1) compositions were synthesized by conventional high-temperature synthesis, and as-synthesized samples were characterized by powder X-ray diffraction experiments. Up to x = 0.7, InPd 3–x Ag x adopts the ternary substitutional variant of the InPd 3 structure (TiAl 3 -type), when x > 0.7, elemental Ag starts to segregate along with the main phase. Accurate structural characterization in InPd 3–x Ag x faces a critical challenge due to the narrow X-ray scattering contrast among constituents In, Pd, and Ag and nearly identical neutron scattering lengths of Pd and Ag. To overcome this “coloring problem”, a combination of calculation of phase diagrams modeling (CALPHAD) and diffraction techniques (X-ray and neutron) was employed. In the compositional range 0 ≤ x ≤ 0.7, InPd 3–x Ag x presents a ternary variant of the TiAl 3 -type structure, where Ag atoms selectively substitute one (the 2b Wyckoff site) of the two Pd sites in InPd 3 . Notably, in contrast to the isologous InPd 3–x Cu x (x = 0–1) system, Ag substitution does not form an ordered VRh 2 Sn-type structure at the limiting composition. The distinct site preference in InPd 3–x Ag x is elucidated by charge population analysis, electronic structure calculations, and orbital-resolved chemical bonding investigations, and the extent of substitution is supported by formation free energy calculations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Selective and Stable In-Promoted Fe Catalyst for Syngas Conversion to Light Olefins

A selective and stable alumina-supported In-promoted Fe catalyst (10 mol % In based on Fe) was discovered for converting syngas (2:1 H 2 /CO ratio) to olefins with high selectivity (45% with CO 2 included) and a remarkable stability (72 h run) at a CO conversion of 10% at 400 °C and 5 bar. The X-ray photoelectron spectroscopy results indicated that incorporating In into Fe catalysts changed the chemical bonding state of Fe and Fe/In composition near the surface layers, which affected the catalytic reactivity. Steady-state isotopic transient kinetic analysis showed that more stable CHx fragments are present on the catalyst surface when incorporating In into Fe, which can promote C–C coupling reaction toward olefins. Our study demonstrates that introducing In into Fe catalysts on Al 2 O 3 support can lower CO activation abilities. It has more impacts on lowering hydrogenation activity, which permits more C–C couplings and like of “ene” hydrogenation. Furthermore, weakening CO adsorption both in terms of sites and strength encouraged CO toward hydrocarbons rather than CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Electrochemical Cycling of Liquid Organic Hydrogen Carriers as a Sustainable Approach for Hydrogen Storage and Transportation

Hydrogen (H 2 ), as a high-energy-density molecule, offers a clean solution to carry energy. However, the high diffusivity and low volumetric density of H 2 pose a challenge for long-term storage and transportation. Liquid organic hydrogen carriers (LOHCs) have been suggested as a strategic way to store and transport hydrogen in stable molecules. More so, electrochemical LOHC cycling renders an opportunity to utilize renewable energy for hydrogen storage and transportation toward the goal of eliminating carbon emissions. In this Perspective, examples of electrochemical reactions of organic molecules and their suitability for LOHC couples are examined. A comparative carbon footprint assessment of electrochemical LOHC cycling processes against thermochemical and hybrid LOHC cycling processes was performed. The electrochemical LOHC cycling process had the lowest relative carbon footprint only when highly concentrated LOHCs were used as the feed or when purification of the LOHC product was not required. The carbon footprint in electrochemical cycling of diluted LOHC was primarily contributed to by the LOHC distillation separation process. A sensitivity analysis showed the carbon footprint LOHC concentration dependence during the electrochemical cycling process. Moreover, the electrolyte composition significantly affects the carbon footprint during electrochemical LOHC cycling. Energy utilization, water usage, and toxicity for electrochemical LOHC cycling are discussed to provide an overview for better economic and environmental practices. There are significant opportunities in the electrochemical cycling of LOHCs if appropriate conditions such as high concentrations of reactant, reversible redox cycling ability, high Faradaic efficiencies, and catalyst stabilities are achieved.

25 ENERGY STORAGE↗
DOE OSTI2021

The role of gas flow distributions on CO 2 mineralization within monolithic cemented composites: coupled CFD-factorial design approach

The carbonation kinetics of monolithic cementing composites are strongly affected by gas transport which is, in turn, influenced by microstructural resistances and the presence of liquid water within pore networks. The non-uniform gas flow distribution within the CO 2 mineralization reactor can impart mass transfer resistance in the monolith microstructure, which affects the uptake of CO 2 (“carbonation”) of the cementing composites. This paper demonstrates how the gas spatial distribution (velocity and flow rate; quantified by CFD analysis) and processing conditions (temperature, relative humidity, and flow rate; quantified by factorial design) affect drying and carbonation, and in turn, the engineering properties of a representative ‘monolithic’ carbonate-cemented concrete component (i.e., herein concrete masonry unit: CMUs, also known as concrete block). It is shown that the gas flow distribution affects drying front penetration and results in moisture and carbonation gradients within the monolith. Particularly, variations in drying kinetics caused by non-uniformity of the contacting gas velocity impose gradients in moisture saturation, which results in increasing microstructural resistance to CO 2 transport. The resultant non-uniform carbonate-mineral formation (i.e., carbonate cementation), if not controlled, can produce gradients in mechanical properties and may alter failure patterns upon loading. Finally, these insights inform the optimal design of gas flow distribution systems and processing conditions within CO 2 mineralization reactors for the manufacturing of low-CO 2 concrete components using CO 2 -dilute industrial flue gas streams.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗