SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low thrust trajectories for minimum time rendezvous between continuous thrust interceptor and passive target vehicle, comparing calculus of variations and steepest ascent analyses
Secondary or abort mission maximized subject to primary mission constraints by variational treatment of optimal branched trajectories
Space shuttle optimal lifting trajectory analysis, examining boost launch system performance increase
The paper addresses the dynamical problem and question of technical feasibility associated with delivering a simple, semi-hard lander to one of the Galilean satellites, Ganymede. Emphasis is placed on the identification of a viable, not necessarily optimal, baseline trajectory and maneuver sequence. Simplicity is stressed in the lander's use of two fixed-impulse solid rockets for landing maneuvers. It is shown through an error analysis that navigation and maneuver execution errors can be compensated on the baseline descent trajectory by controlling just the thrust direction. Finally, specific subsystem capabilities needed on the lander to achieve a successful touchdown within a specific performance envelope are also identified.
The Transferable Output ASCII Data (TOAD) Gateway, release 1.0 is described. This is a software tool for converting tabular data from one format into another via the TOAD format. This initial release of the Gateway allows free data interchange among the following file formats: TOAD; Standard Interface File (SIF); Program to Optimize Simulated Trajectories (POST) input; Comma Separated Value (TSV); and a general free-form file format. As required, additional formats can be accommodated quickly and easily.
Simulations are conducted to investigate a proposed NASA launch vehicle that is fully reusable, takes off horizontally, and uses airbreathing propulsion in a single stage. The propulsion model is based on a cycle analysis method, and the vehicle is assumed to be a rigid structure with distributed fuel, operating under a range of atmospheric conditions. The program to optimize simulated trajectories (POST) is modified to include a predictor-corrector guidance capability and then used to generate the trajectories. Significant errors are encountered during the unpowered coast phase due to uncertainty in the atmospheric density profile. The amount of ascent propellant needed is shown to be directly related to the thrust-vector angle and the location of the center of gravity of the vehicle because of the importance of aim-drag losses to total ideal velocity.
A robust feedback algorithm is presented for a near-minimum-fuel ascent of a two-stage launch vehicle operating in the equatorial plane. The development of the algorithm is based on the ideas of neighboring optimal control and can be derived into three phases. In phase 1, the formalism of optimal control is employed to calculate fuel-optimal ascent trajectories for a simple point-mass model. In phase 2, these trajectories are used to numerically calculate gain functions of time for the control(s), the total flight time, and possibly, for other variables of interest. In phase 3, these gains are used to determine feedback expressions for the controls associated with a more realistic model of a launch vehicle. With the Advanced Launch System in mind, all calculations are performed on a two-stage vehicle with fixed thrust history, but this restriction is by no means important for the approach taken. Performance and robustness of the algorithm is found to be excellent.
Explore the source record for details and available documents.
An optimal stabilization problem for discrete event systems (DES) is addressed. A class of not necessarily finite state 'logical' DES models is utilized which can also model the costs for events to occur. Let P and A denote two such models. Suppose that P characterizes the valid behavior of a dynamical system and A represents certain design objectives which specify the allowable DES behavior which is 'contained in' the valid behavior. An optimal control problem for P and A is how to choose the sequence of inputs to P so that the DES behavior lies in A (i.e., it is allowable) and so that a performance index defined in terms of the costs of the events is minimized. Two solutions are provided to an optimal stabilization problem, i.e. how to find a sequence of inputs that results in an optimal state trajectory which cycles in a pre-specified set.
The objectives of the Space Transfer Vehicle (STV) Concepts and Requirements studies were to provide sensitivity data on usage, economics, and technology associated with new space transportation systems. The study was structured to utilize data on the emerging launch vehicles, the latest mission scenarios, and Space Exploration Initiative (SEI) payload manifesting and schedules, to define a flexible, high performance, cost effective, evolutionary space transportation system for NASA. Initial activities were to support the MSFC effort in the preparation of inputs to the 90 Day Report to the National Space Council (NSC). With the results of this study establishing a point-of-departure for continuing the STV studies in 1990, additional options and mission architectures were defined. The continuing studies will update and expand the parametrics, assess new cargo and manned ETO vehicles, determine impacts on the redefined Phase 0 Space Station Freedom, and to develop a design that encompasses adequate configuration flexibility to ensure compliance with on-going NASA study recommendations with major system disconnects. In terms of general requirements, the objectives of the STV system and its mission profiles will address crew safety and mission success through a failure-tolerant and forgiving design approach. These objectives were addressed through the following: engine-out capability for all mission phases; built-in-test for vehicle health monitoring to allow testing of all critical functions such as, verification of lunar landing and ascent engines before initiating the landing sequence; critical subsystems will have multiple strings for redundancy plus adequate supplies of onboard spares for removal and replacement of failed items; crew radiation protection; and trajectories that optimize lunar and Mars performance and flyby abort capabilities.
TOAD Gateway is interactive software tool for converting data files to and from variety of file formats. Currently reads and writes following file formats: TOAD; Standard Interface File (SIF); Program to Optimize Simulated Trajectories (POST) input; Comma Separated Value and Tab Separated Value, common in PC and Macintosh spreadsheet and database packages; and general free format. Additional modules for accommodating other formats easily developed and installed. Companion program, TOAD Editor (LAR-14423), manipulates contents of TOAD files and extracts selected subsets of data. TOAD Gateway written in FORTRAN 77.
This work reviews the use of aerodynamic forces to modify the velocity, and therefore, the orbital path of vehicles due to transit through planetary atmospheres, especially when high values of lift can be generated. The concepts of aerobraking and aerocapture are examined, and the limiting factors are discussed. The use of high L/D vehicles, such as hypersonic waveriders, is examined, and the advantages and disadvantages of their use for aerocapture are addressed. This preliminary study of non-optimized aerocapture trajectories suggests that entrance velocities at Mars can be 10 - 12 km/sec for a waverider while sustaining acceptable loads of about 3 - 4 Earth G's over a 3 minute period, diminishing to less than 1 G in about 15 minutes. The entrance velocities are greater than those for a more conventional biconic configuration with similar deceleration loads sustained. The convective heating rate on the waverider, increased due to the higher velocities and sharp leading edges, has an estimated upper bound of 14000 W/sq cm and a corresponding temperature of about 7500 degrees K.
A suite of computer codes was assembled to simulate the performance of an aerospike engine and to generate the engine input for the Program to Optimize Simulated Trajectories. First an engine simulator module was developed that predicts the aerospike engine performance for a given mixture ratio, power level, thrust vectoring level, and altitude. This module was then used to rapidly generate the aerospike engine performance tables for axial thrust, normal thrust, pitching moment, and specific thrust. Parametric engine geometry was defined for use with the engine simulator module. The parametric model was also integrated into the iSIGHT multidisciplinary framework so that alternate designs could be determined. The computer codes were used to support in-house conceptual studies of reusable launch vehicle designs.
A suite of computer codes was assembled to simulate the performance of an aerospike engine and to generate the engine input for the Program to Optimize Simulated Trajectories. First an engine simulator module was developed that predicts the aerospike engine performance for a given mixture ratio, power level, thrust vectoring level, and altitude. This module was then used to rapidly generate the aerospike engine performance tables for axial thrust, normal thrust, pitching moment, and specific thrust. Parametric engine geometry was defined for use with the engine simulator module. The parametric model was also integrated into the iSIGHTI multidisciplinary framework so that alternate designs could be determined. The computer codes were used to support in-house conceptual studies of reusable launch vehicle designs.
Free-flight is considered to play a major role in the future air traffic environment. Studies are underway addressing different concepts for free-flight and self separation in enroute airspace. One common opinion throughout the different concepts is that the airspace surrounding major airports, the Terminal Radar Approach CONtrol (TRACON) will not be a free flight area. This means that aircraft in this area are completely controlled by air traffic controllers, who may be supported by decision support system like the Center TRACON Automation System (CTAS). How the transition from the free-flight area (enroute airspace) to the terminal area will take place is currently unclear, This paper describes a study at NASA Ames Research Center addressing the perspective of air traffic controllers handling user-preferred (FMS-optimized) descent trajectories during this transition phase. Two major issues in enabling user preferred descents from the controllers' point of view are predictability and controllability. In an environment in which the air traffic services are highly responsive to user preferences controllers need to know, where and when aircraft will change their trajectory and they need to have appropriate means and procedures at hand to control the aircraft according to the overall traffic situation. Predictability shall be enhanced by: 1) Indicating airspace corridors for descending aircraft; 2) Modify the controller interface; 3) Using a ground based conflict probe; 4) Making use of downlinked intent information from the aircraft FMS; and 5) Requiring to fly pilots on user preferred trajectories coupled to the FMS in the lateral and vertical axis. Additional controllability shall be achieved by supporting the controllers with CTAS center tools: 1) Traffic Management Advisor (TMA); 2) Conflict Probing and Trial Planning (CP/TP); and 3) Enroute Descent Advisor (E/DA). The paper describes the general concept and the modifications to current systems required to enable the concept. It explains the experiment design and discusses the results with regard to controller acceptability and usability. Potential benefits and drawbacks of the overall concept are indicated.
Design of missions beyond our solar system presents many challenges. Here, we consider certain aspects of the solar-sail launched interstellar probe (ISP), a spacecraft slated for launch in the 2010 time period that is planned to reach the heliopause, at 200 Astronomical Units (AU) from the Sun after a flight of about 20-years duration. The baseline mission under consideration by NASA / JPL has a sail radius of 200 m, a science payload of 25 kg, a spacecraft areal mass thickness of about two grams per square meter and is accelerated out of the solar system at about 14 AU per year after performing a perihelion pass of about 0.25 AU. In current plans, the sail is to be dropped near Jupiter's orbit (5.2 AU from the Sun) on the outbound trajectory leg. One aspect of this study is application of a realistic model of sail thermo-optics to sail kinematics that includes diffuse / specular reflectance and sail roughness. The effects of solar-wind degradation of sail material, based on recent measurements at the NASA MSFC (Marshall Space Flight Center) Space Environment Facility were incorporated in the kinematical model. After setting initial and final conditions for the spacecraft, trajectory was optimized using the provision of variable sail aspect angle. The second phase of the study included consideration of rainbow holography as a medium for a message plaque that would be carried aboard the ISP in the spirit of the message plaques aboard Pioneer 10 /11 and Voyager 1 /2. A prototype holographic message plaque was designed and created by artist C. Bangs with the assistance of Ana Maria Nicholson and Dan Schweitzer of the Center for Holographic Arts in Long Island City, NY. The piece was framed by Simon Liu Inc. of Brooklyn, NY. Concurrent to the creation of the prototype message plaque, we explored the potential of this medium to transmit large amounts of visual information to any extraterrestrial civilization that might detect and intercept ISP. It was also necessary to investigate possible degradation of holograms by the space environment. We developed a new way of characterizing the optical quality of holograms.
Jet Propulsion Laboratory (JPL) developed video overlay calibration and demonstration techniques for ground-based telerobotics. Through a technology sharing agreement with JPL, Deneb Robotics added this as an option to its robotics software, TELEGRIP. The software is used for remotely operating robots in nuclear and hazardous environments in industries including automotive and medical. The option allows the operator to utilize video to calibrate 3-D computer models with the actual environment, and thus plan and optimize robot trajectories before the program is automatically generated.
Two primary simulations have been developed and are being updated for the Mars Smart Lander Entry, Descent, and Landing (EDL). The high fidelity engineering end-to-end EDL simulation that is based on NASA Langley's Program to Optimize Simulated Trajectories (POST) and the end-to-end real-time, hardware-in-the-loop simulation testbed, which is based on NASA JPL's (Jet Propulsion Laboratory) Dynamics Simulator for Entry, Descent and Surface landing (DSENDS). This paper presents the status of these Mars Smart Lander EDL end-to-end simulations at this time. Various models, capabilities, as well as validation and verification for these simulations are discussed.