Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Surface fluxes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Design of a thermocapillary flow experiment in reduced gravity

Detailed considerations for the design of a low-gravity thermocapillary flow experiment are presented. The basic configuration is one in which a fluid contained in a circular dish is subjected to an imposed surface heat flux. Specific consideration is given to the imposed thermal signature, thermal boundary conditions, free-surface deformations, and g-jitter effects. Numerical analysis and ground-based and drop-tower tests are utilized to ensure that reasonable flows are obtained in which measurements can be made relatively easily. The configuration chosen is of further importance because it differs from others in which oscillations were observed.

Kamotani, Y.↗
NASA NTRS2014

Orion MPCV Continuum RCS Heating Augmentation Model Development

The reaction control system jets of the Orion Multi Purpose Crew Vehicle can have a significant impact on the magnitude and distribution of the surface heat flux on the leeside of the aft-body, when they are fired. Changes in surface heating are expressed in terms of augmentation factor over the baseline smooth body heating. Wind tunnel tests revealed heating augmentation factors as high as 13.0, 7.6, 2.8, and 5.8 for the roll, pitch down, pitch up, and yaw jets respectively. Heating augmentation factor models, based almost exclusively on data from a series of wind tunnel tests have been developed, for the purposes of thermal protection system design. The wind tunnel tests investigated several potential jet-to-freestream similarity parameters, and heating augmentation factors derived from the data showed correlation with the jet-to-freestream momentum ratio. However, this correlation was not utilized in the developed models. Instead augmentation factors were held constant throughout the potential trajectory space. This simplification was driven by the fact that ground to flight traceability and sting effects are not well understood. Given the sensitivity of the reaction control system jet heating augmentation to configuration, geometry, and orientation the focus in the present paper is on the methodology used to develop the models and the lessons learned from the data. The models that are outlined in the present work are specific to the aerothermal database used to design the thermal protection system for the Exploration Flight Test 1 vehicle.

Heating Augmentation↗
NASA NTRS1999

Satellite Estimated Surface Heat Budgets in the Pacific Warm Pool During TOGA COARE

Chou (1998) produced daily mean surface net shortwave and longwave radiative fluxes for the westem Pacific warm pool (from the Japan GMS data) for the COARE IOP (intensive observing period). In addition, daily mean air-sea turbulent fluxes have been produced from the SSM/I data using the method of Chou (1997). In this paper, we focus on three areas. The first area is to further assess accuracy of the retrieved daily mean surface fluxes using those from the IMET buoy, RV Moana Wave, and RV IWecoma. The second area is to describe the temporal and spatial variability of the surface heat budget (as well as the related parameters) over the warm pool during the IOP. The third area is to discuss the relation of SST (sea surface temperature) change to surface fluxes, including the tranmission of solar flux through the ocean mix-layer.

Chou, Shu-Hsien↗
DOE OSTI2021

Boundary Layer Climatology at ARM Southern Great Plains

Operational since 1992, the Atmospheric Radiation Measurement (ARM) southern great plains (SGP) site at Oklahoma, USA has become a reference research site for meteorological studies. Due to an open data policy the ARM data are used by researchers all over the world. In this report, we review the long-term climatology of the atmospheric boundary layer, SGP instrumentations, the site and some site-specific atmospheric conditions which potentially effect wind turbines within the region. As the atmospheric boundary layer is bounded and influenced by the surface, observations of surface radiation components and heat fluxes are crucial in understanding land-atmosphere interactions. The entrainment of air, updrafts, downdrafts and boundary layer height characteristics is needed for understanding the structure and growth of the atmospheric boundary layer. Therefore, measurements from both surface in-situ and remote sensing observations at SGP provide an overall climatology and their interactions from surface up to the boundary layer. Measurements from a 60 m meteorological tower, surface flux stations, disdrometers, soil temperature and moisture flux plates, coherent Doppler lidar, Raman lidar, radiosondes, and satellite data at SGP central facility were analyzed. All the measurements were generally within a few square kilometers of each other at the central facility. This report focuses on data from January 2010 to June 2020 at SGP central facility. The various sections describe the ARM SGP site and surrounding wind turbines; in-situ and remote sensing instrumentation used in the report; provides mathematical equations to analyze fluxes, turbulence and other boundary layer parameters; a climatological analysis of surface winds, fluxes and thermodynamic parameters for several years; an analysis of observed winds in the framework of Monin-Obukhov Similarity Theory; an analysis of the boundary layer winds and direction from a Doppler lidar; multi-year turbulence estimates through the boundary layer from a Doppler lidar; atmospheric boundary layer water vapor and relative humidity profiles from Raman lidar; cloud base height and boundary layer height from multiple sensors and satellite data; and finally site specific atmospheric conditions, such as nocturnal low-level jets. Diurnal, seasonal and yearly variations of surface, sub-surface and boundary layer quantities, such as wind speed, direction, temperature, atmospheric stability, soil temperature, and various atmospheric fluxes at SGP showed distinct trends useful for focused modeling studies. The applicability of surface similarity theory on ARM SGP data is also evaluated, which showed northerly flows are aligned with MO theory estimates compared to southerly flows. Boundary layer winds and direction profiles for several years from a Doppler lidar shows a consistent presence of a nocturnal low-level jet and predominant southerly wind directions through the boundary layer at SGP. The inter-annual variability at SGP is low (<3.5%), with a mean annual wind speed of approximately 7 m s -1 at 100 m above ground level. Boundary layer turbulence and moisture transport from Doppler and Raman lidars are evaluated, which provides evidence of increased water vapor mass flux into the great plains during nocturnal low-level jets. The moisture flux from nocturnal low-level jets is observed to be maximum during summer periods. A novel machine learning algorithm is implemented to accurately estimate the planetary boundary layer height, providing further insights into growth and destruction of the convective boundary layer height during various seasons and land-atmosphere conditions. The high frequency of low-level clouds during winter, spring and fall seasons is validated using the multi-sensor array and satellite estimates of cloud top height. Satellite vegetative fraction data provides insight into seasonal surface roughness and vegetation variability around SGP site.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1990

Land surface parameterization for regional surface heat transfer in hilly grassland

Radiometrically obtained surface temperature data and wind and temperature data from the atmospheric boundary layer are analyzed to determine the regional surface-heat flux. Monin-Obukhov similarity theory is employed to analyze the wind speed and the relationship between the surface potential temperature and the potential temperature. The radiometric scalar roughness is considered and found to be related to solar elevation and canopy height, although the regional sensible heat flux derived by the similarity theory analysis agrees with measured flux values.

Sugita, Michiaki↗
NASA NTRS1989

Remote sensing of the thermal forcing on the tropical Pacific

Monthly fields of shortwave radiation (SR) and latent heat flux (LE) over the central and eastern tropical Pacific between 1980 and 1983 have been computed using satellite data. They are the dominant variable components of surface thermal forcing on the ocean in this time scale. During the 1982-1983 ENSO episode, surface-wind convergence and cloudiness associated with the displacement of equatorial organized convection caused a reduction in both the SR into the ocean and the LE out of the ocean. The lag-correlation coefficients between the forcing (SR-LE) and the sea surface temperature are found to be significantly high outside the equatorial region, showing that surface thermal forcing is the dominant factor in sea surface temperature change. In the narrow equatorial wave guide, ocean dynamics play a more important role, and surface heat flux is a consequence rather than the cause of sea surface temperature change.

Liu, W. Timothy↗
NASA NTRS1995

Calculation of surface and top of atmosphere radiative fluxes from physical quantities based on ISCCP data sets. 2: Validation and first results

We use global, multiyear observations of the properties of clouds, the atmosphere, and the surface to calculate global shortwave (SW) and longwave (LW) fluxes at the top of the atmosphere and at the surface at a resolution of 280 km and 3 hours for every third month from April 1985 to January 1989. Our validation studies suggest that the specification of cloud effects is no longer the dominant uncertainty in reconstructing the radiative fluxes at the top of atmosphere and at the surface. Rather cloud property uncertainties are now roughly equal contributors to the flux uncertainty, along with surface and atmospheric properties. The resulting SW and LW flux data sets suggest the following conclusions: (1) The net SW heating of Earth appears predominantly at the surface, whereas the net LW cooling arises predominantly from the atmosphere. The net cooling effect of clouds on top of atmospheric radiation appears primarily at the surface rather than in the atmosphere. (2) Clouds have almost no net effect on the global mean radiation balance of the atmosphere, but they enhance the latitudinal gradient in the LW cooling and reinforce the radiative forcing for the mean atmospheric circulation. Clouds act to mute seasonal contrasts however. (3) Clouds enhance the land-ocean contrasts of the atmospheric cooling, reinforcing the growth of standing eddy motions; but reduce land-ocean contrasts of the surface heating.

Rossow, W. B.↗
NASA NTRS1988

Velocity distributions of oxygen atoms incident on spacecraft surfaces

The angular distributions of oxygen atoms incident on surfaces in low earth orbit have been calculated for a number of ambient gas temperatures. Atom fluxes to surfaces were modeled by integrals over all permitted angles of incidence. Angles of incidence are limited by masking structures, and a number of types of mask were considered. Combustible surfaces exposed to the orbital atmosphere are heavily etched, creating profiles in mask shadows that are sensitive to ambient temperatures. The influence of the angular distributions on the characteristics of etched surfaces is discussed. Profiles measured for a September, 1983 flight were fitted to this model profile with a temperature of 750 + or - 50 K, which agrees with estimates based on solar activity at that time. Applications to sensing ambient temperatures and oxygen atom densities are discussed.

Peters, P. N.↗
NASA NTRS2000

Validation of CERES/TERRA Data

There are 2 CERES scanning radiometer instruments aboard the TERRA spacecraft, one for mapping the solar radiation reflected from the Earth and the outgoing longwave radiation and the other for measuring the anisotropy of the radiation. Each CERES instrument has on-board calibration devices, which have demonstrated that from ground to orbit the broadband total and shortwave sensor responses maintained their ties to the International Temperature Scale of 1990 at precisions approaching radiances have been validated in orbit to +/- 0.3 % (0.3 W/sq m sr). Top of atmosphere fluxes are produced by use of the CERES data alone. By including data from other instruments, surface radiation fluxes and radiant fluxes within the atmosphere and at its top, shortwave and longwave, for both up and down components, are derived. Validation of these data products requires ground and aircraft measurements of fluxes and of cloud properties.

Barkstrom, Bruce R.↗
NASA NTRS2004

Kinetic Roughening and Energetics of Tetragonal Lysozyme Crystal Growth: A Preliminary Atomic Force Microscopy Investigation

We examined particulars of crystal growth from measurements obtained at both microscopic and molecular levels. The crystal growth measurements performed at the microscopic level are well characterized by a model that balances the flux of macromolecules towards the crystal surface with the flux of the crystal surface. Numerical evaluation of model with measurements of crystal growth, in time, provided accurate estimates for the average growth velocities. Growth velocities thus obtained were also interpreted using well-established phenomenological theories. Moreover, we find that microscopic measurements of growth velocity measurements obtained as a function of temperature best characterizes changes in crystal growth modes, when present. We also examined the possibility of detecting a change in crystal growth modes at the molecular level using atomic force microscopy, AFM. From preliminary AFM measurements performed at various supersaturations, we find that magnitude of surface height fluctuations, h(x), increases with supersaturation. Further examination of surface height fluctuations using methods established for fluctuation spectroscopy also enabled the discovery of the existence of a characteristic length, c, which may possibly determine the mode of crystal growth. Although the results are preliminary, we establish the non- critical divergence of 5 and the root-mean-square (rms) magnitude of height-height fluctuations as the kinetic roughening transition temperatures are approached. Moreover, we also examine approximate models for interpreting the non-critical behavior of both 6 and rms magnitude of height-height fluctuations, as the solution supersaturation is increased towards the kinetic roughening supersaturation.

Gorti, Sridhar↗
NASA NTRS2003

Intraseasonal Oscillations over South America: A Study with a Regional Climate Model

The National Center for Atmospheric Research (NCAR) regional climate model version 2 (RegCM2) is used to investigate the observed characteristics of intraseasonal oscillations over South America. Our study is mainly concentrated on an intraseaonal mode, which is observed to account for a large portion of the intraseasonal variation, to have a standing feature and to be independent of the MJO. The NCEPDOE AMIP-II reanalysis is utilized to provide initial and lateral boundary conditions for the RegCM2 based upon the OOZ, 062, 122 and 182 data.Our results indicate that the intraseasonal oscillation still exists with time- averaged lateral boundary condition, which prevents the MJO and other outside disturbances from entering the model's domain, suggesting a locally forced oscillation responsible for ths intraseasonal mode independent of the MJO. Further experiments show that the annual and daily variabilities and a radiative-convective interaction are not essential to the locally forced intraseasonal oscillation. The intraseasonal oscillations over Amazon in our model essentially result from interactions among atmospheric continental- scale circulation, surface radiation, surface sensible and latent heat fluxes, and cumulus convection. The wavelet analyses of various surface energy fluxes and surface energy budget also verify that the primary cause of intraseasonal oscillation is the interaction of land surface processes with the atmosphere.

Chen, Baode↗
DOE OSTI2020

Azimuthally averaged wind and thermodynamic structures of tropical cyclones in global climate models and their sensitivity to horizontal resolution

Characteristics of tropical cyclones (TCs) in global climate models (GCMs) are known to be influenced by details of the model configurations, including horizontal resolution and parameterization schemes. Understanding model-to-model differences in TC characteristics is a prerequisite for reducing uncertainty in future TC activity projections by GCMs. This study performs a process-level examination of TC structures in eight GCM simulations that span a range of horizontal resolutions from 1° to 0.25°. A recently developed set of process-oriented diagnostics is used to examine the azimuthally averaged wind and thermodynamic structures of the GCM-simulated TCs. Results indicate that the inner-core wind structures of simulated TCs are more strongly constrained by the horizontal resolutions of the models than are the thermodynamic structures of those TCs. As expected, the structures of TC circulations become more realistic with smaller horizontal grid spacing, such that the radii of maximum wind (RMW) become smaller, and the maximum vertical velocities occur off the center. However, the RMWs are still too large, especially at higher intensities, and there are rising motions occurring at the storm centers, inconsistently with observations. The distributions of precipitation, moisture, radiative and surface turbulent heat fluxes around TCs are diverse, even across models with similar horizontal resolutions. At the same horizontal resolution, models that produce greater rainfall in the inner-core regions tend to simulate stronger TCs. Further, when TCs are weak, the radial gradient of net column radiative flux convergence is comparable to that of surface turbulent heat fluxes, emphasizing the importance of cloud-radiative feedbacks during the early developmental phases of TCs.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1989

Transport dynamics calculated under the full Mie scattering theory for micron and submicron lunar ejecta in selenocentric, cislunar, and geocentric space

In 1967, Lunar Explorer 35 was launched from the earth and placed into a stable orbit around the moon. The data from the dust particle experiment on this spacecraft were essentially continuous over a 5-yr period from the time of insertion in lunar orbit. Analysis of this data has been interpreted to show that micron-sized lunar ejecta leave the moon and traverse through selenocentric and cislunar space and obtain either interplanetary/heliocentric orbits or intercept the earth's magnetosphere and move into geocentric orbits. Extensive studies of the orbital trajectories of lunar particles in this size range have now been conducted that include a calculation of the solar radiation force using the full Mie scattering theory. A significant flux of particles with radii less than 0.1 micron are found to intercept the earth's magnetopause surface. This flux is shown to be strongly dependent upon both the particle's density and its index of refraction.

Hyde, T. W.↗
NASA NTRS2011

Monitoring Delamination of Thermal Barrier Coatings During Interrupted High-Heat-Flux Laser Testing using Luminescence Imaging

This presentation showed progress made in extending luminescence-base delamination monitoring to TBCs exposed to high heat fluxes, which is an environment that much better simulates actual turbine engine conditions. This was done by performing upconversion luminescence imaging during interruptions in laser testing, where a high-power CO2 laser was employed to create the desired heat flux. Upconverison luminescence refers to luminescence where the emission is at a higher energy (shorter wavelength) than the excitation. Since there will be negligible background emission at higher energies than the excitation, this methods produces superb contrast. Delamination contrast is produced because both the excitation and emission wavelengths are reflected at delamination cracks so that substantially higher luminescence intensity is observed in regions containing delamination cracks. Erbium was selected as the dopant for luminescence specifically because it exhibits upconversion luminescence. The high power CO2 10.6 micron wavelength laser facility at NASA GRC was used to produce the heat flux in combination with forced air backside cooling. Testing was performed at a lower (95 W/sq cm) and higher (125 W/sq cm) heat flux as well as furnace cycling at 1163C for comparison. The lower heat flux showed the same general behavior as furnace cycling, a gradual, "spotty" increase in luminescence associated with debond progression; however, a significant difference was a pronounced incubation period followed by acceleration delamination progression. These results indicate that extrapolating behavior from furnace cycling measurements will grossly overestimate remaining life under high heat flux conditions. The higher heat flux results were not only accelerated, but much different in character. Extreme bond coat rumpling occurred, and delamination propagation extended over much larger areas before precipitating macroscopic TBC failure. This indicates that under the higher heat flux (and surface & interface temperatures), the TBC was more tolerant of damage. The main conclusions were that high heat flux conditions can not only accelerate TBC debond progression but can also grossly alter the pathway of delamination.

Eldridge, Jeffrey I.↗
NASA NTRS1990

Suggestions for the measurement and derivation of fluxes and flux divergences from a satellite

Consideration is given to the determination of the optimal bands for measuring and deriving the total outgoing longwave radiation (OLR), surface downward flux (SDF), and cooling rates (CRs) using linear regression. The optimal bands are determined from scatter plots of total fluxes and cooling rates associated with the various bands. It is found that the best band for OLR is between 800 and 1200/cm, while the best band for SDF is between 500 and 660/cm or between 660 and 800/cm. For CRs, it is shown that the best band is also between 660 and 800/cm. It is noted that the AVHRR OLR is damped compared with the Nimbus-7 earth radiation budget (ERB) OLR derived from the broadband, narrow FOV ERB instrument.

Wu, Man-Li C.↗
DOE OSTI2022

Effect of PVD-coated chromium on the subcooled flow boiling performance of nuclear reactor cladding materials

Here we elucidate the separate effect of a thin Cr coating deposited by physical vapor deposition (PVD) on the subcooled flow boiling performance of zircaloy-4. First, we run flow boiling experiments on prototypical zircaloy-4 surfaces mimicking the scratch pattern and surface roughness of nuclear reactor claddings. Then, we PVD-coat a 0.3 µm thick chromium layer on the same exact surface and repeat the same flow boiling investigations. All experiments are run using deionized water at atmospheric pressure, flowing on a 1 × 3 cm 2 rectangular cross section channel at a rate of 1000 kg/m 2 /s and a subcooling of 10 K. We measure the average temperature of the boiling surface at increasing surface heat fluxes, covering a wide range of heat transfer regimes, from single-phase forced convection to the boiling crisis. We also record high-speed videos of the boiling process, which we postprocess to measure bubble nucleation site density, growth time, departure diameter and frequency. The surface analysis reveals that, while the chromium coating does not seem change the surface roughness and morphology, it improves surface wettability. However, it decreases the critical heat flux. The chromium coating causes an increase of nucleation temperature, bubble departure diameter and growth time, and a reduction of the nucleation site density. The concurrence of these observations indicates that a size reduction of the nucleation sites, conformally covered by the chromium coating, may be the cause of the boiling performance deterioration. We confirm this hypothesis repeating the same analysis on a FeCrAl sample prepared and tested using the same protocol as the zircaloy-4 sample, but with a different initial surface texture.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1980

Stellar coronae from Einstein - Observations and theory

Einstein Observatory observations of stellar X-ray emission are presented and their implications for the formation of stellar coronae and the problem of stellar angular momentum loss are discussed. Solar coronal X-ray observations and observations of stellar coronae made prior to Einstein are reviewed, and it is noted that they already suggest that the standard theory of acoustic coronal heating is inadequate. The principal results of the Einstein/CfA stellar survey are summarized, with attention given to variations of the level of X-ray flux detected along the main sequence, the decline of X-ray flux with increasing age of giants and supergiants, and indications of a large range of X-ray emission levels within a given type, which are clearly incompatible with models for acoustic flux generation. A new theory to explain stellar coronae and hence X-ray emission from them is then proposed in which stellar magnetic fields play the key role in determining the level of coronal emission, and the modulation of the surface magnetic flux level and the level of stressing of surface magnetic fields essentially determine the variation of mean coronal activity in the H-R diagram.

Rosner, R.↗
NASA NTRS1979

Core cooling by subsolidus mantle convection

Although vigorous mantle convection early in the thermal history of the earth is shown to be capable of removing several times the latent heat content of the core, a thermal evolution model of the earth in which the core does not solidify can be constructed. The large amount of energy removed from the model earth's core by mantle convection is supplied by the internal energy of the core which is assumed to cool from an initial high temperature given by the silicate melting temperature at the core-mantle boundary. For the smaller terrestrial planets, the iron and silicate melting temperatures at the core-mantle boundaries are more comparable than for the earth; the models incorporate temperature-dependent mantle viscosity and radiogenic heat sources in the mantle. The earth models are constrained by the present surface heat flux and mantle viscosity and internal heat sources produce only about 55% of the earth model's present surface heat flow.

Schubert, G.↗