Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Strain-relaxed tetragonal MAPbI 3 results in efficient mesoporous solar cells

In mesoporous organo-halide perovskite solar cells, the coexistence of tetragonal phase and cubic phase in the perovskite layer is found to result in strained crystal structure at the mesoporous TiO 2 (mp-TiO 2 )/perovskite heterointerface. This results in structural defects pinholes, grain boundaries, and interfacial porosity which is detrimental towards photovoltaic performance and device stability. The strain at the interface originates from the lattice mismatch between the mp-TiO 2 nanoparticles (NPs) and perovskite. Here, a transformative approach is demonstrated to realize relaxed and high purity tetragonal phase MAPbI 3 (RP) near the mp-TiO 2 interface region. This approach involves inserting a ~2 nm lattice matched buffer layer of cubic CsPbBr 3 between mp-TiO 2 NPs and MAPbI 3 , which serves as a template for epitaxial growth for top MAPbI 3 . As a result, the solar cell with relaxed MAPbI3 shows a power conversion efficiency (PCE) of 22.12% with significantly enhanced environmental, light, and thermal stability.

14 SOLAR ENERGY↗

Optimization of Thin-Film Solar Cells for Lunar Surface Operations

Thin-film solar cells have been in production for decades, but technology has only recently advanced enough to allow for comparable efficiencies to traditional rigid cells. Some of the benefits of thin-films, such as lighter weight and being foldable, are particularly advantageous to space applications since mass and volume are key considerations of any flight project. Using these thin-film cells in space, however, is outside of their ground-based design criteria. This requires special care to be taken in designing the power generation system of a spacecraft around a thin-film solar cell, particularly in regards to thermal management. Without the diffusion of an atmosphere to mitigate solar load, the temperature of the panels can rapidly exceed their design specification. In this paper a design solution is presented that allows for thin-film solar cells to be used in a robotic lunar lander. Due to the low thermal mass and in-plane conductivity of thin films, it is difficult to remove waste heat by any other method than radiation. On the lunar surface this means angling the arrays to increase their view factor to space, which has the negative consequence of decreasing their power generation. An optimization was developed to balance the heat rejection and power generation of the cells, using constraints on the maximum cell temperature and minimum spacecraft power requirements. The resulting solar panel angle was then used as an input to the Thermal Desktop model to verify the final panel temperatures.

Breeding, Shawn↗

Assessing the true power of bifacial perovskite solar cells under concurrent bifacial illumination

An accurate assessment of bifacial solar cells under concurrent bifacial illumination is critical to evaluate their real photovoltaic performance. Here, we demonstrate bifacial perovskite solar cells with bifacial equivalent power conversion efficiencies of 21% and 26% under concurrent bifacial illumination with an albedo of 0.2 and 0.5, respectively. A detailed balance efficiency limit analysis further reveals the full potential of bifacial perovskite solar cells.

14 SOLAR ENERGY↗

On-demand formation of Lewis bases for efficient and stable perovskite solar cells

In the fabrication of FAPbI 3 -based perovskite solar cells, Lewis bases play a crucial role in facilitating the formation of the desired photovoltaic α-phase. However, an inherent contradiction exists in their role: they must strongly bind to stabilize the intermediate δ-phase, yet weakly bind for rapid removal to enable phase transition and grain growth. To resolve this conflict, we introduced an on-demand Lewis base molecule formation strategy. This approach utilized Lewis-acid-containing organic salts as synthesis additives, which deprotonated to generate Lewis bases precisely when needed and could be reprotonated back to salts for rapid removal once their role is fulfilled. This method promoted the optimal crystallization of α-phase FAPbI 3 perovskite films, ensuring the uniform vertical distribution of A-site cations, larger grain sizes and fewer voids at buried interfaces. Perovskite solar cells incorporating semicarbazide hydrochloride achieved an efficiency of 26.1%, with a National Renewable Energy Laboratory-certified quasi-steady-state efficiency of 25.33%. These cells retained 96% of their initial efficiency after 1,000 h of operation at 85 °C under maximum power point tracking. Additionally, mini-modules with an aperture area of 11.52 cm 2 reached an efficiency of 21.47%. This strategy is broadly applicable to all Lewis-acid-containing organic salts with low acid dissociation constants and offers a universal approach to enhance the performance of perovskite solar cells and modules.

14 SOLAR ENERGY↗

Role of p-GaN layer thickness in the degradation of InGaN-GaN MQW solar cells under 405 nm laser excitation

GaN-based solar cells with InGaN multiple quantum wells (MQWs) are promising devices for application in space environment, concentrator solar systems, wireless power transmission and multi-junction solar cells. It is therefore important to understand their degradation kinetics when submitted to high-temperature and high-intensity stress. We submitted three samples of GaN-InGaN MQW solar cells with p-AlGaN electron-blocking-layer with different thickness of the p-GaN layer to constant power stress at 310 W/cm 2 , 175 °C for several hundred hours. The main degradation modes are a reduction of open-circuit voltage, short-circuit current, external quantum efficiency, power conversion efficiency and electroluminescence. In particular, we observed that a thinner p-GaN layer results in a stronger degradation observed on the cell operating parameters. The analysis of the dark I-V characteristics showed an increase in low-forward bias current and the analysis of electroluminescence showed a decrease in the electroluminescene emitted by the (forward biased) cell, as a consequence of stress. This work highlights that the cause of degradation is possibly related to a diffusion mechanism, which results in an increase of defect density in the active region. Finally, the impurities involved in the diffusion processes possibly originate from the p-side of the devices, therefore a thicker p-GaN layer reduces the amount of defects reaching the active region.

14 SOLAR ENERGY↗

A comparison between pulsed and CW laser annealing for solar cell applications

The application of laser processing in solar cell fabrication is considered. Specific emphasis is placed on a process developed for the fabrication of a 16.6% silicon solar cell using pulsed laser processing. Results are presented which compare pulsed laser annealing with CW laser annealing in solar cell fabrication.

Jellison, G. E., Jr.↗

Laboratory instrumentation and techniques for characterizing multi-junction solar cells for space applications

Multi-junction solar cells are attractive for space applications because they can be designed to convert a larger fraction of AMO into electrical power at a lower cost than single-junction cells. The performance of multi-junction cells is much more sensitive to the spectral irradiance of the illuminating source than single-junction cells. The design of high efficiency multi-junction cells for space applications requires matching the optoelectronic properties of the junctions to AMO spectral irradiance. Unlike single-junction cells, it is not possible to carry out quantum efficiency measurements using only a monochromatic probe beam and determining the cell short-circuit current assuming linearity of the quantum efficiency. Additionally, current-voltage characteristics can not be calculated from measurements under non-AMO light sources using spectral-correction methods. There are reports in the literature on characterizing the performance of multi junction cells by measuring and convoluting the quantum efficiency of each junction with the spectral irradiance; the technique is of limited value for the characterization of cell performance under AMO power-generating conditions. We report the results of research to develop instrumentation and techniques for characterizing multi junction solar cells for space . An integrated system is described which consists of a standard lamp, spectral radiometer, dual-source solar simulator, and personal computer based current-voltage and quantum efficiency equipment. The spectral radiometer is calibrated regularly using the tungsten-halogen standard lamp which has a calibration based on NIST scales. The solar simulator produces the light bias beam for current-voltage and cell quantum efficiency measurements. The calibrated spectral radiometer is used to 'fit' the spectral irradiance of the dual-source solar simulator to WRL AMO data. The quantum efficiency apparatus includes a monochromatic probe beam for measuring the absolute cell quantum efficiency at various voltage biases, including the voltage bias corresponding to the maximum-power point under AMO light bias. The details of the procedures to 'fit' the spectral irradiance to AMO will be discussed. An assessment of the role of the accuracy of the 'fit' of the spectral irradiance and probe beam intensity on measured cell characteristics will be presented. quantum efficiencies were measured with both spectral light bias and AMO light bias; the measurements show striking differences. Spectral irradiances were convoluted with cell quantum efficiencies to calculate cell currents as function of voltage. The calculated currents compare with measured currents at the 1% level. Measurements on a variety of multi-junction cells will be presented. The dependence of defects in junctions on cell quantum efficiencies measured under light and voltage bias conditions will be presented. Comments will be made on issues related to standards for calibration, and limitations of the instrumentation and techniques. Expeditious development of multi-junction solar cell technology for space presents challenges for cell characterization in the laboratory.

Woodyard, James R.↗

Novel Approach for Selective Emitter Formation and Front Side Metallization of Crystalline Silicon Solar Cells

In this project we will explore the possibility of forming the front side metallization and selective emitter layer for the crystalline silicon solar cells through using selective laser ablation to create contact openings on the front surface and a screen printer to make connections with conductive paste. Using this novel approach we expect to reduce the specific contact resistance of the silver gridlines by about one order of magnitude compared to the state-of-art industrial crystalline silicon solar cells to below 1 mΩ∙cm 2 , and use lightly doped n+ emitter layer with sheet resistance of not smaller than 100 Ω. This represents an enabling improvement on crystalline silicon solar cell performance and can increase the absolute efficiency of the solar cell by about 1%. In this scientific report we first present our result on the selective laser ablation of the nitride layer to make contact openings. Then we report our work on the solar cell fabrication by using the laser ablated contact openings with self-doping paste. Through various electrical property characterization and SIMS analysis, the factors limiting the cell performance have been discussed. While through this proof-of-concept project we could not reach the target on cell efficiency improvement, the process to fabricate 125mm full-sized silicon solar cells using laser ablation and self-doping paste has been developed, and a much better understanding of technical challenges has been achieved. Future direction to realize the potential of the new technology has been clearly defined.

14 SOLAR ENERGY↗

Theoretical temperature dependence of solar cell parameters

A simple formulation has been derived for the temperature dependence of cell parameters for any solar cell material. Detailed calculations have been performed for high-quality monocrystalline GaAs, Si and Ge cells. Preliminary experimental data for GaAs and Si cells are close to the calculated values. In general, the higher the energy gap of a material, the small is the temperature dependence of its solar cell parameters.

Fan, John C. C.↗

Systematic analysis of diffuse rear reflectors for enhanced light trapping in silicon solar cells

Simple diffuse rear reflectors can enhance the light path length of weakly absorbed near infrared light in silicon solar cells and set a benchmark for more complex and expensive light trapping structures like dielectric gratings or plasmonic particles. We analyzed such simple diffuse rear reflectors systematically by optical and electrical measurements. We applied white paint, TiO 2 nanoparticles, white backsheets and a silver mirror to bifacial silicon solar cells and measured the enhancement of the external quantum efficiency for three different solar cell geometries: planar front and rear side, textured front and planar rear side, and textured front and rear side. We showed that an air-gap between the solar cell and the reflector decreases the absorption enhancement significantly, thus white paint and TiO 2 nanoparticles directly applied to the rear cell surface lead to the highest short circuit current density enhancements. Here, the short circuit current density gains for a 200 um thick planar solar cell reached up to 1.8 mA/cm 2 , compared to a non-reflecting black rear side and up to 0.8 mA/cm 2 compared to a high-quality silver mirror rear side. For solar cells with textured front side the short circuit current density gains are in the range between 0.5 and 1.0 mA/cm 2 compared to a non-reflecting black rear side and do not significantly depend on the angular characteristic of the rear side reflector but mainly on its absolute reflectance.

14 SOLAR ENERGY↗

Doped GaInAs/GaP Quantum Well Superlattice Solar Cells With 27.5% Efficiency

Quantum wells can extend the absorption range of a solar cell and are typically placed in the intrinsic region of the device to enable efficient carrier collection via drift. Thick intrinsic regions are needed for significant absorption in the low bandgap quantum wells, resulting in a large depletion region recombination and ultimately a solar cell with a low fill factor (FF). However, in quantum well superlattice solar cells where tunneling plays a dominant role in carrier transport, collection by carrier diffusion may be possible, relieving the requirement for quantum wells to be placed in the intrinsic region. Here, we investigate doping in stress-balanced quantum well superlattice solar cells using thin 2 nm GaP barriers. Doping reduces J02 depletion region recombination and improves the solar cell FF up to 86.7%, but very high doping eventually reduces the carrier collection, leading to a tradeoff in efficiency. Finally, we show that the barrier thickness also plays an important role in carrier collection, and we demonstrate high efficiency 27.5% single-junction devices with a doped superlattice.

13 HYDRO ENERGY↗

Progress in the Multijunction Solar Cell Mantech Program

In September, 1995, the joint Wright Laboratory/Phillips Laboratory/NASA Lewis Multijunction Solar Cell Manufacturing Technology (ManTech) Program began to improve multijunction cell performance and scale them up to production size and quantity to support Air Force and commercial satellite programs. The first milestone of the program has been reached and the purpose of this paper is to present the results of the program so far. The objectives of the Multijunction Solar Cell ManTech Program are to increase the GaInP2/GaAs/Ge lot average cell efficiency to 24-26%, increase the cell size to > or equal to 16 sq cm while maintaining high efficiency, and limit the per cell costs to < or equal to 1.15X state of the art GaAs/Ge cells. Advanced manufacturing technology and process control techniques such as in-situ process monitoring and real time process feedback are being used to optimize multijunction solar cell growth processes to achieve these goals. This paper will discuss progress made in Phase I of the program and give an overview of Phase II but will focus on side-by-side testing results collected by Phillips Laboratory and NASA Lewis on Phase I deliverable cells from both vendors. Cell performance, pre- and post radiation, and temperature coefficient results on initial production multijunction solar cells will be presented and discussed. The data shows that this technology meets the objectives of the program, and that, in the interim before a new solar simulation standard becomes widely available, the measurement techniques being used by the major space solar cell manufacturers are providing adequate testing results for solar array design.

Keener, David N.↗

Solar cells fabricated with unconventional silicon materials

Solar cells have been fabricated using silicon materials supplied in the DOE/JPL Large Solar Array program. Each of the silicon materials studied in this program was produced in a unique manner and with intent of producing silicon in a grade and form that would offer the possibility of economic deployment in photovoltaic arrays for generation of electricity. This report will attempt to provide an overview of the results for some of the materials and highlight in particular results obtained for solar cells fabricated from the advanced CZ silicon. Emphasis will be given to consideration of the purity of virgin silicon material used in the heat exchange method.

Minahan, J. A.↗

III-V Solar Cells with Novel Epitaxial Lift-off Architectures for Extended Substrate Reuse for Low-cost Manufacturing

The highest solar cell efficiencies have been achieved with III-V photovoltaics (PV). Still, the use of III-V materials in terrestrial applications has been very limited, mainly because of their high cost. The high cost is primarily due to the expensive Ge or GaAs wafers which could amount up to one-half of the total module cost! A prominent approach to reduce the impact of the high cost of substrates used for III-V PV is through re-use of the wafer substrates by Epitaxial Lift-Off (ELO). Typically, using a sacrificial layer such as AlAs, the device part of the cell is lifted off, leaving behind the substrate for re-use for fabrication of the next device. While conversion efficiency as high as 29.1% has been achieved by ELO method, chemical mechanical polishing (CMP) of the substrate is required which significantly adds to the overall solar cell cost. In this project, we have developed a novel ELO architecture for single junction gallium arsenide (GaAs) solar cells that will not require CMP of the substrate for re-use. Multiple reuses of GaAs wafers have been demonstrated with no CMP, without degradation in solar cell efficiency. Also, the solar cells have been successfully lifted off and transferred to inexpensive substrates with less than 2% change in efficiency. By elimination of the CMP process, which is the highest cost component of III-V solar cells made by conventional ELO method (~$10/W), and decreasing the substrate cost by multiple re-uses, the developed technology could be a leap forward in significantly reducing the cost of III-V photovoltaics.

14 SOLAR ENERGY↗

Trap-Assisted Dopant Compensation Prevents Shunting in poly-Si Passivating Interdigitated Back Contact Silicon Solar Cells

Interdigitated back contact (IBC) solar cells achieve the highest efficiencies of single-junction architectures, but complicated patterning of the rear fingers and spreading of dopants during processing inhibit their mainstream adoption due to concerns of shunting between the IBC fingers. One method of simplifying patterning at the rear is by using contact masks combined with plasma-enhanced chemical vapor deposition (PECVD) or ion implantation. However, the intrinsic isolation region becomes contaminated during high-temperature annealing by lateral diffusion of dopants and during masked PECVD by spreading of dopant radicals through region between the mask and the substrate. Despite this contamination, we show through scanning spreading resistance microscopy and Kelvin probe force microscopy that a ~20 µm wide compensating region exists with high enough resistivity to prevent shunting. We model this p-i-n poly-Si system using two simulation models: a simple resistor model considering only the capture of charge carriers by trap defects in poly-Si to reduce the conductivity, and a more refined 1-dimensional finite element model using Poisson’s equation, drift-diffusion equations, and recombination of carriers. Using this model, we show that high defect density significantly decreases the current across the region between the p- and n-type fingers, preventing shunting.

atom probe↗

Production status of GaAs/Ge solar cells and panels

GaAs/Ge solar cells with lot average efficiencies in excess of 18 percent were produced by MOCVD growth techniques. A description of the cell, its performance and the production facility are discussed. Production GaAs/Ge cells of this type were recently assembled into circuits and bonded to aluminum honeycomb panels to be used as the solar array for the British UOSAT-F program.

Smith, B.↗

Initial results for the silicon monolithically interconnected solar cell product

This proprietary technology is based on AstroPower's electrostatic bonding and innovative silicon solar cell processing techniques. Electrostatic bonding allows silicon wafers to be permanently attached to a thermally matched glass superstrate and then thinned to final thicknesses less than 25 micron. These devices are based on the features of a thin, light-trapping silicon solar cell: high voltage, high current, light weight (high specific power) and high radiation resistance. Monolithic interconnection allows the fabrication costs on a per watt basis to be roughly independent of the array size, power or voltage, therefore, the cost effectiveness to manufacture solar cell arrays with output powers ranging from milliwatts up to four watts and output voltages ranging from 5 to 500 volts will be similar. This compares favorably to conventionally manufactured, commercial solar cell arrays, where handling of small parts is very labor intensive and costly. In this way, a wide variety of product specifications can be met using the same fabrication techniques. Prototype solar cells have demonstrated efficiencies greater than 11%. An open-circuit voltage of 5.4 volts, fill factor of 65%, and short-circuit current density of 28 mA/sq cm at AM1.5 illumination are typical. Future efforts are being directed to optimization of the solar cell operating characteristics as well as production processing. The monolithic approach has a number of inherent advantages, including reduced cost per interconnect and increased reliability of array connections. These features make this proprietary technology an excellent candidate for a large number of consumer products.

Dinetta, L. C.↗

III-V-N materials for super high-efficiency multijunction solar cells

We have been studying concentrator multi-junction solar cells under Japanese Innovative Photovoltaic R and D program since FY2008. InGaAsN is one of appropriate materials for 4-or 5-junction solar cell configuration because this material can be lattice-matched to GaAs and Ge substrates. However, present InGaAsN single-junction solar cells have been inefficient because of low minority-carrier lifetime due to N-related recombination centers and low carrier mobility due to alloy scattering and non-homogeneity of N. This paper presents our major results in the understanding of majority and minority carrier traps in GaAsN grown by chemical beam epitaxy and their relationships with the poor electrical properties of the materials.

36 MATERIALS SCIENCE↗