Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polar system modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Case Study for Lunar ISRU Systems Utilizing Polar Water

In-Situ Resource Utilization (ISRU) is key to long term presence at any extraterrestrial destination. Current NASA direction is to achieve a sustainable presence on the lunar surface by 2028. Mission plans currently target the lunar South Pole to leverage the extended periods of solar illumination and allows for potential access to water ice in the permanently shadowed areas around the poles. With water, it is possible to produce both fuel and oxidizer to fully refuel a vehicle. In order to address ISRU infusion into mission planning, a study of an end-to-end ISRU propellant production system was initiated to assess ISRU architectures and obtain mass and power estimates for each. The results of these case studies will be presented. For this study, The ISRU system architecture involved two sites; the mine site in a shadowed crater where water ice is excavated and extracted from the regolith and the propellant production site at an illuminated ridge where the water is processed into liquefied O2 and H2 propellants. Fixed hardware would be emplaced at each site, with two alternating water tankers to transport water between them. Notional lunar sites were identified for this architecture for baseline environmental parameters. Technology solutions for each subsystem were selected based on those with the highest fidelity models or those that have empirical laboratory data to anchor to. While power needs were identified for each location, a power solution was not prescribed, therefore the masses presented do not include surface power systems. The baseline case in this study assumed that 10 mT of oxygen, along with enough hydrogen to support a propulsion mixture ratio of 6, must be produced in 225 days. Therefore 15 mT of water would need to be collected and processed. The baseline solution resulted in a system mass of5 mT and a total required power of 68kW. The majority of the mass was split between the ridge site system and the two water tankers (2.6 mTand 1.8mTrespectively). The majority of the required power was with three subsystems at approximately 20 kW each: hydrogen liquefaction, electrolysis, and the water extractor subsystem. Trades for four key variables are also presented, namely production rate, water concentration, dry overburden depth, and number of water transport trips. This can be compared to a system that targets oxygen from the minerals in the surface regolith material. A carbothermal reduction reactor system was used for this comparison. The use of direct solar thermal energy to process the regolith and the ease of access of the resource resulted in significantly lower values for the oxygen case: approximately 2.7 mT and 11.8 kW. However, the mass trade would favor the water case over successive missions where the hydrogen up-mass of 2 mT per mission will accrue against the oxygen system.1Aerospace Research Engineer, Chemical and Thermal Propulsion Systems Branch, Senior Member.2Mechanical Engineer, Propulsion and Power Division/Energy Conversion Systems, 2101 Nasa Pkwy/Mailcode EP3 Houston, TX 77058, AIAA member.

Lunar↗
DOE OSTI2022

Changes in polarization dictate necessary approximations for modeling electronic deexcitation intensity: Application to x-ray emission

Accurate simulation of electronic excitations and deexcitations are critical for complementing complex spectroscopic experiments and can provide validation to theoretical approaches. Here, using a generalized framework, we contrast the accuracy and validity of orbital-constrained and linear-response approaches that build upon Kohn-Sham density functional theory (DFT) to simulate emission spectra of electronic origin and propose an efficient approximation, named many-body x-ray emission spectroscopy or MBXES, for simulating such processes. We show analytically as well as with computed examples that for electronic (de)excitation leading to an appreciable change in polarization (i.e., density rearrangement), the adiabatic approximation in a response-based formalism will be inadequate for the calculation of oscillator strength. Thus, such a change (e.g., in the net electrostatic dipole moment of a finite system) can be used as a metric for evaluating the applicability of the adiabatic response-based approach and can be particularly valuable in x-ray emission spectroscopy. On the other hand, MBXES, the flexible method introduced in this paper, can compute oscillator strengths accurately at a much lower computational expense on the basis of two DFT-based self-consistent field calculations. Using illustrative examples of emission spectra, the efficacy of the MBXES method is demonstrated by comparison with its parent theory, orbital-optimized DFT, and with experiments.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2025

LDRD Abbreviated report: High-Order General-Discrete-Ordinates Method Enabling Efficient Deterministic Transport in Hydrodynamic Simulations

Deterministic transport simulations for national-security and energy applications often operate in high-dimensional phase-space, where accuracy and cost both become major challenges. A common numerical artifact in such problems is the “ray-effect,” which appears as unphysical streaks. Beyond misinterpretation, these artifacts can contaminate tightly coupled physics, such as fluid dynamics, radiation-hydrodynamics, and laser-plasma interactions, eroding the predictive capability of entire multiphysics workflows. Our objective was to make high-dimension studies practical on modern hardware while mitigating the ray-effect without relying on prohibitively expensive sampling approaches such as Monte Carlo methods. We developed the Generic Discretization Library (GenDiL), a Graphics Processing Unit (GPU)-first framework that uses high-order Discontinuous Galerkin (DG) methods and matrix-free algorithms to reduce memory usage and improve computational efficiency, critical for phase-space simulations. GenDiL supports phase-space adaptivity in both mesh size and polynomial order (hp-adaptivity) to place resolution only where it is needed. A central capability is Local Dimensional Refinement (LDR), which couples lower-dimension continuum models to higher-dimension kinetic models through stable and conservative interfaces, so that high-fidelity physics is applied only in regions where it is essential. Building on the GenDiL framework, we developed the General SN (GSN) family of algorithms as a true generalization of the polar SN approach (discrete ordinates, often denoted SN). Rather than tying discrete ordinates to a specific polar change of coordinates, GSN formulates transport on an arbitrary change of coordinates chosen to reduce ray-effect. We studied two complementary variants: an analytic variant, where the coordinate map is prescribed in advance by a closed-form function; and a data-driven variant, where a quantity of interest, such as the net flux, guides the coordinate system. GenDiL provides the library infrastructure for efficient GPU execution, but the GSN concept is algorithmic and independent of any one library. Across representative high-dimension tests, including non-symmetric solutions, both variants delivered strong ray-effect mitigation at practical cost, moving four- to six-dimensional analysis toward repeatable, routine studies.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1986

Joule heating and field-aligned currents: Preliminary results from DE-2

There are three main processes by which energy is transferred from the magnetosphere to the thermosphere: (1) charge exchange of the ring current particles; (2) precipitation of charged particles; and (3) joule dissipation by the magnetosphere-ionosphere current systems. The importance of this last process has been recognized and the rate of joule heating has been estimated by many workers. Observations of the electric (E) and magnetic (B) fields from Dynamics Explorer Satellite 2 are providing a new set of data on field-aligned currents. One of the remarkable features found in these observations is the high correlation between an orthogonal pair of the E and B field components. In recent years, observational data have accrued concerning the relationship between the interplanetary magnetic field and the size of the polar cap and also about the evolution of a substorm or a magnetic storm. It is suggested that these findings be incorporated in future model calculations.

Sugiura, M.↗
NASA NTRS2000

What we can Learn About Aerosols from EOS-MISR Multi-Angle Remote Sensing Observations

Multiangle, multispectral remote sensing observations, such as those anticipated from the Earth Observing System (EOS) Multiangle Imaging SpectroRadiometer (MISR), promise to significantly improve our ability to constrain aerosol properties from space. Recent advances in modeling the Earth's climate have brought us to a point where the contributions made by aerosols to the global radiation budget noticeably affect the results. Knowledge of both aerosol optical depth and the microphysical properties of particles is needed to adequately model aerosol effects. This talk explores the ability of multiangle, multi-spectral remote sensing observations anticipated from the EOS MISR instrument, to retrieve aerosol optical depth and information about mixes of particle types, globally, at 17.6 km spatial resolution. The instrument is scheduled for launch into a 10:30 AM, sun-synchronous polar orbit in 1999.

Kahn, Ralph↗
NASA NTRS2002

XTE Observations of Intermediate Polars: RXTE TOO Observations of Supernovae

Two intermediate polar cataclysmic variables, PQ Gem and AO Psc, were observed jointly with the Rossi X-ray Timing Explorer (RXTE) and ground-based photometry. The analysis of intermediate polars (IPs) is complex because these objects exhibit light curves that behave differently as a function of energy and that behave differently when phased on the orbital or on the spin periods. The presence of two periods in one system is essentially equivalent to analyzing two different X-ray sources. A preliminary analysis of the PQ Gem data was carried out and presented at the Annapolis Workshop on Magnetic Cataclysmic Variables. The final analysis of the data were held up by problems with the background estimation. The RXTE PCA team has released a new version of the background estimator. The PQ Gem must be reanalyzed using the new background. We have also installed a spectral model that calculates the expected emission from an accretion column. That model is undergoing final testing before we apply it to the data.

Schlegel, E.↗
NASA NTRS2003

Impact of Flow-Dependent Error Correlations and Tropospheric Chemistry on Assimilated Ozone

The presentation compares different versions of a global three-dimensional ozone data assimilation system developed at NASA's Data Assimilation Office. The Solar Backscatter Ultraviolet/2 (SBUV/2) total and partial ozone column retrievals are the sole data assimilated in all of the experiments presented. We study the impact of changing the forecast error covariance model from a version assuming static correlations with a one that captures a short-term Lagrangian evolution of those correlations. This is further combined with a study of the impact of neglecting the tropospheric ozone production, loss and dry deposition rates, which are obtained from the Harvard GEOS-CHEM model. We compare statistical characteristics of the assimilated data and the results of validation against independent observations, obtained from WMO balloon-borne sondes and the Polar Ozone and Aerosol Measurement (POAM) III instrument. Experiments show that allowing forecast error correlations to evolve with the flow results in positive impact on assimilated ozone within the regions where data were not assimilated, particularly at high latitudes in both hemispheres. On the other hand, the main sensitivity to tropospheric chemistry is in the Tropics and sub-Tropics. The best agreement between the assimilated ozone and the in-situ sonde data is in the experiment using both flow-dependent error covariances and tropospheric chemistry.

Wargan, K.↗
NASA NTRS2019

High-fidelity Imaging of the Inner AU Mic Debris Disk: Evidence of Differential Wind Sculpting?

We present new high-fidelity optical coronagraphic imagery of the inner ∼50 au of AU Mic's edge-on debris disk using the BAR5 occulter of the Hubble Space Telescope Imaging Spectrograph (HST/STIS) obtained on 2018 July 26–27. This new imagery reveals that "feature A," residing at a projected stellocentric separation of 14.2 au on the southeast side of the disk, exhibits an apparent "loop-like" morphology at the time of our observations. The loop has a projected width of 1.5 au and rises 2.3 au above the disk midplane. We also explored Transiting Exoplanet Survey Satellite photometric observations of AU Mic that are consistent with evidence of two starspot complexes in the system. The likely co-alignment of the stellar and disk rotational axes breaks degeneracies in detailed spot modeling, indicating that AU Mic's projected magnetic field axis is offset from its rotational axis. We speculate that small grains in AU Mic's disk could be sculpted by a time-dependent wind that is influenced by this offset magnetic field axis, analogous to co-rotating solar interaction regions that sculpt and influence the inner and outer regions of our own Heliosphere. Alternatively, if the observed spot modulation is indicative of a significant misalignment of the stellar and disk rotational axes, we suggest that the disk could still be sculpted by the differential equatorial versus polar wind that it sees with every stellar rotation.

John P. Wisniewski↗
NASA NTRS2015

EM Modeling of Far-Field Radiation Patterns for Antennas on the GMA-TT UAV

To optimize communication with the Generic Modular Aircraft T-Tail (GMA-TT) unmanned aerial vehicle (UAV), electromagnetic (EM) simulations have been performed to predict the performance of two antenna types on the aircraft. Simulated far-field radiation patterns tell the amount of power radiated by the antennas and the aircraft together, taking into account blockage by the aircraft as well as radiation by conducting and dielectric portions of the aircraft. With a knowledge of the polarization and distance of the two communicating antennas, e.g. one on the UAV and one on the ground, and the transmitted signal strength, a calculation may be performed to find the strength of the signal travelling from one antenna to the other and to check that the transmitted signal meets the receiver system requirements for the designated range. In order to do this, the antenna frequency and polarization must be known for each antenna, in addition to its design and location. The permittivity, permeability, and geometry of the UAV components must also be known. The full-wave method of moments solution produces the appropriate dBi radiation pattern in which the received signal strength is calculated relative to that of an isotropic radiator.

Mackenzie, Anne I.↗
NASA NTRS1983

Thermal modeling and analysis of structurally complex spacecraft using the IDEAS system

Large antenna satellites of unprecedented sizes are needed for a number of applications. Antenna diameters on the order of 50 meters and upward are required. Such antennas involve the use of large expanses of lattice structures with hundreds or thousands of individual connecting members. In connection with the design of such structures, the consideration of thermal effects represents a crucial factor. Software capabilities have emerged which are coded to include major first order thermal effects and to purposely ignore, in the interest of computational efficiency, the secondary effects. The Interactive Design and Evaluation of Advanced Spacecraft (IDEAS) is one such system. It has been developed for an employment in connection with thermal-structural interaction analyses related to the design of large structurally complex classes of future spacecraft. An IDEAS overview is presented. Attention is given to a typical antenna analysis using IDEAS, the thermal and loading analyses of a tetrahedral truss spacecraft, and ecliptic and polar orbit analyses.

Garrett, L. B.↗
DOE OSTI2020

Flue Gas CO 2 Capture via Electrochemically Mediated Amine Regeneration: Desorption Unit Design and Analysis

We analyzed the performance of an electrochemical desorption unit to be implemented in an electrochemically mediated amine regeneration (EMAR) process, which separates CO 2 and regenerates the amine upon modulation of a targeted species that complexes with the amine molecules. Using a simplified one-dimensional boundary layer model, we combined the kinetic expressions of the faradaic reactions with mass transfer effects to analyze the polarization behavior of the flow cell. Mass transfer limitations become dominant at high current densities, leading to increases in energy consumption. An understanding of scaling laws with key parameters, such as the Sherwood number, is required to achieve high power operation with minimal mass transfer losses. Because the EMAR chemistry is sensitive to temperature, heat distribution in the unit is also examined. Our results indicate that the desorption performance increases with addition of a high-temperature heat source. Additionally, incorporation of membrane crossover suggests energy losses because of diffusion and migration of active species. Furthermore, these findings inform on scaling laws for at-scale desorber design and provide a model for scaling up the EMAR system for larger scale operations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Revealing the Electrochemical Kinetics of Electrolytes in Nanosized LiFePO 4 Electrodes

Lithium-ion battery rate performance is ultimately limited by the electrolyte, yet the behaviors of electrolytes during high-rate (dis)charge remain elusive to electrochemical measurement. Herein, we develop and study a nanosized LiFePO 4 model system in which the electrolyte completely controls the electrochemical kinetics of the porous electrode. Impedance spectroscopy, cyclic voltammetry, and rate performance testing prove that ion transport in the electrolyte is the sole rate-limiting process, even in thin electrodes. A novel pseudo-steady-state extrapolation (S3E) method for Tafel analysis shows that LiFePO 4 obeys Butler-Volmer kinetics with a transfer coefficient of 3. The combination of these unexpectedly rapid interfacial kinetics and an activation barrier for phase transformation causes extreme reaction heterogeneity, which manifests as a moving reaction zone. Resistance versus capacity analysis enables direct measurement of electrolyte resistance growth during high-rate (dis)charge, revealing how the interaction between concentration polarization and a moving reaction zone controls electrolyte rate performance in LiFePO 4 electrodes. This work elucidates the profound impacts of the electrolyte on electrochemical measurements in porous battery electrodes: when the active material is not rate limiting, it is impossible to directly measure the intrinsic kinetics of the active material, but conversely, it becomes possible to directly measure the kinetics of the electrolyte.

Electrochemistry↗
NASA NTRS2008

Juno Mission Simulation

The Juno spacecraft is planned to launch in August of 2012 and would arrive at Jupiter four years later. The spacecraft would spend more than one year orbiting the planet and investigating the existence of an ice-rock core; determining the amount of global water and ammonia present in the atmosphere, studying convection and deep- wind profiles in the atmosphere; investigating the origin of the Jovian magnetic field, and exploring the polar magnetosphere. Juno mission management is responsible for mission and navigation design, mission operation planning, and ground-data-system development. In order to ensure successful mission management from initial checkout to final de-orbit, it is critical to share a common vision of the entire mission operation phases with the rest of the project teams. Two major challenges are 1) how to develop a shared vision that can be appreciated by all of the project teams of diverse disciplines and expertise, and 2) how to continuously evolve a shared vision as the project lifecycle progresses from formulation phase to operation phase. The Juno mission simulation team addresses these challenges by developing agile and progressive mission models, operation simulations, and real-time visualization products. This paper presents mission simulation visualization network (MSVN) technology that has enabled a comprehensive mission simulation suite (MSVN-Juno) for the Juno project.

space vehicles↗
NASA NTRS2012

High-Contrast NIR Polarization Imaging of MWC480

One of the key predictions of modeling from the IR excess of Herbig Ae stars is that for protoplanetary disks, where significant grain growth and settling has occurred, the dust disk has flattened to the point that it can be partially or largely shadowed by the innermost material at or near the dust sublimation radius. When the self-shadowing has already started, the outer disk is expected to be detected in scattered light only in the exceptional cases that the scale height of the dust disk at the sublimation radius is smaller than usual. High-contrast imaging combined with the IR spectral energy distribution allow us to measure the degree of flattening of the disk, as well as to determine the properties of the outer disk. We present polarimetric differential imaging in H band obtained with Subaru/HiCIAO of one such system, MWC 480. The HiCIAO data were obtained at a historic minimum of the NIR excess. The disk is detected in scattered light from 0".2-1"0 (27.4-137 AU). Together with the marginal detection of the disk from 1998 February 24 by HST / NICMOS, our data constrain the opening half angle for the disk to lie between 1.3 <= Theta <=2.2 deg. When compared with similar measures in CO for the gas disk from the literature, the dust disk subtends only approx 30% of the gas disk scale height (H/R approx 0. 03). Such a dust disk is a factor of 5-7 flatter than transitional disks, which have structural signatures that giant planets have formed.

McElwain, M. W.↗
NASA NTRS2016

Effect of Satellite Formations and Imaging Modes on Global Albedo Estimation

We confirm the applicability of using small satellite formation flight for multi-angular earth observation to retrieve global, narrow band, narrow field-of-view albedo. The value of formation flight is assessed using a coupled systems engineering and science evaluation model, driven by Model Based Systems Engineering and Observing System Simulation Experiments. Albedo errors are calculated against bi-directional reflectance data obtained from NASA airborne campaigns made by the Cloud Absorption Radiometer for the seven major surface types, binned using MODIS' land cover map - water, forest, cropland, grassland, snow, desert and cities. A full tradespace of architectures with three to eight satellites, maintainable orbits and imaging modes (collective payload pointing strategies) are assessed. For an arbitrary 4-sat formation, changing the reference, nadir-pointing satellite dynamically reduces the average albedo error to 0.003, from 0.006 found in the static reference case. Tracking pre-selected waypoints with all the satellites reduces the average error further to 0.001, allows better polar imaging and continued operations even with a broken formation. An albedo error of 0.001 translates to 1.36 W/sq m or 0.4% in Earth's outgoing radiation error. Estimation errors are found to be independent of the satellites' altitude and inclination, if the nadir-looking is changed dynamically. The formation satellites are restricted to differ in only right ascension of planes and mean anomalies within slotted bounds. Three satellites in some specific formations show average albedo errors of less than 2% with respect to airborne, ground data and seven satellites in any slotted formation outperform the monolithic error of 3.6%. In fact, the maximum possible albedo error, purely based on angular sampling, of 12% for monoliths is outperformed by a five-satellite formation in any slotted arrangement and an eight satellite formation can bring that error down four fold to 3%. More than 70% ground spot overlap between the satellites is possible with 0.5deg of pointing accuracy, 2 Km of GPS accuracy and commands uplinked once a day. The formations can be maintained at less than 1 m/s of monthly (Delta)V per satellite.

BRDF↗
DOE OSTI2022

Spin-polarized imaging of the antiferromagnetic structure and field-tunable bound states in kagome magnet FeSn

Abstract Kagome metals are an exciting playground for the explorations of novel phenomena at the intersection of topology, electron correlations and magnetism. The family of FeSn-based kagome magnets in particular attracted a lot of attention for simplicity of the layered crystal structure and tunable topological electronic band structure. Despite a significant progress in understanding their bulk properties, surface electronic and magnetic structures are yet to be fully explored in many of these systems. In this work, we focus on a prototypical kagome metal FeSn. Using a combination of spin-averaged and spin-polarized scanning tunneling microscopy, we provide the first atomic-scale visualization of the layered antiferromagnetic structure at the surface of FeSn. In contrast to the field-tunable electronic structure of cousin material Fe 3 Sn 2 that is a ferromagnet, we find that electronic density-of-states of FeSn is robust to the application of external magnetic field. Interestingly, despite the field insensitive electronic band structure, FeSn exhibits bound states tied to specific impurities with large effective moments that strongly couple to the magnetic field. Our experiments provide microscopic insights necessary for theoretical modeling of FeSn and serve as a spring board for spin-polarized measurements of topological magnets in general.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1987

Potential surfaces for O atom-polymer reactions

Ab initio quantum chemistry methods are used to study the energetics of interactions of O atoms with organic compounds. Polyethylene (CH2)n has been chosen as the model system to study the interactions of O(3P) and O(1D) atoms with polymers. In particular, H abstraction is investigated and polyethylene is represented by a C3 (propane) oligomeric model. The gradient method, as implemented in the GRADSCF package of programs, is used to determine the geometries and energies of products and reactants. The saddle point, barrier geometry is determined by minimizing the squares of the gradients of the potential with respect to the internal coordinates. To correctly describe the change in bonding during the reaction at least a two configuration MCSCF (multiconfiguration self consistent field) or GVB (generalized valence bond) wave function has to be used. Basis sets include standard Pople and Dunning sets, however, increased with polarization functions and diffuse p functions on both the C and O atoms. The latter is important due to the O(-) character of the wave function at the saddle point and products. Normal modes and vibrational energy levels are given for the reactants, saddle points and products. Finally, quantitative energetics are obtained by implementing a small CAS (complete active space) approach followed by limited configuration interaction (CI) calculations. Comparisons are made with available experimental data.

Laskowski, B. C.↗
NASA NTRS2018

Effects of Greenhouse Gas Increase and Stratospheric Ozone Depletion on Stratospheric Mean Age of Air in 1960-2010

The relative impacts of greenhouse gas (GHG) increase and stratospheric ozone depletion on stratospheric mean age of air in the 1960-2010 period are quantified using the Goddard Earth Observing System Chemistry-Climate Model. The experiment compares controlled simulations using a coupled atmosphere-ocean version of the Goddard Earth Observing System Chemistry-Climate Model, in which either GHGs or ozone depleting substances, or both factors evolve over time. The model results show that GHGs and ozone-depleting substances have about equal contributions to the simulated mean age decrease, but GHG increases account for about two thirds of the enhanced strength of the lower stratospheric residual circulation. It is also found that both the acceleration of the diabatic circulation and the decrease of the mean age difference between downwelling and upwelling regions are mainly caused by GHG forcing. The results show that ozone depletion causes an increase in the mean age of air in the Antarctic summer lower stratosphere through two processes: (1) a seasonal delay in the Antarctic polar vortex breakup that inhibits young midlatitude air from mixing with the older air inside the vortex, and (2) enhanced Antarctic downwelling that brings older air from middle and upper stratosphere into the lower stratosphere.

stratospheric ozone depletion↗