SEARCH · Engineering Papers

Results for “Plastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Hermetically sealable package for hybrid solid-state electronic devices and the like

A light-weight, inexpensively fabricated, hermetically sealable, repairable package for small electronic or electromechanical units, having multiple connections, is described. A molded ring frame of polyamide-imide plastic (Torlon) is attached along one edge to a base plate formed of a highly heat conducting material, such as aluminum or copper. Bores are placed through a base plate within the area of the edge surface of ring frame which result in an attachment of the ring frame to the base plate during molding. Electrical leads are molded into the ring frame. The leads are L-shaped gold-plated copper wires imbedded within widened portions of the side wall of the ring frame. Within the plastic ring frame wall the leads are bent (typically, though not necessarily at 90 deg) so that they project into the interior volume of the ring frame for connection to the solid state devices.

Miller, Wilson N.↗

NASA NTRS1988

Variable response load limiting device

An energy absorbing device used as a load limiting member in a structure to control its response to applied loads is described. It functions by utilizing a spool assembly having flanged ends and an interior cavity of sufficiently large diameter to cause it to deform plastically at a prescribed load. In application, the spool is utilized as a pivot point for the legs of an airplane seat. When properly designed and integrated into the seat arrangement the spool will twist about its axis, deforming plastically when the impact load exceeds the spool yield value. Through this deformation, the spool absorbs the kinetic energy of the movement of the seat at a substantially constant rate, thereby controlling the level of loads transmitted to the seat occupant. By proper sizing and collection of materials, it is possible to control load response in a predictable manner.

Mcsmith, Dwight D.↗

NASA NTRS1987

Human blood platelets at microgravity

A set of freshly collected and separated human platelet suspensions were transported, in three types of plastic containers, on a 6 day, 2 hr mission of the orbiter Columbia to study the effect of prolonged exposure of human blood cells to microgravity. A controlled environment at a temperature of 22 + or - 1 deg with air flow was provided and another set of samples held on the ground acted as controls. Paired comparisons of platelets at ug versus controls at lxg revealed superior platelet survival at microgravity. When viewed in terms of plastic type, ug platelets in containers fabricated from PVC-TOTM displayed the best overall postflight viability.

Surgenor, D. MACN.↗

NASA NTRS1987

Cyclic hardening mechanisms in Nimonic 80A

A nickel base superalloy was fatigued under constant plastic strain range control. The hardening response was investigated as a function of plastic strain range and particle size of the gamma prime phase. Hardening was found to be a function of the slip band spacing. Numerous measurements of the slip band spacing and other statistical data on the slip band structures were obtained. Interactions between intersecting slip systems were shown to influence hardening. A Petch-Hall model was found to describe best this relationship between the response stress and the slip band spacing.

Lerch, B. A.↗

NASA NTRS1987

A simple device for the preparation of embedded materials science specimens for ultramicrotomy

A simple hand-held grinding fixture is discussed which can produce microtome mounts of hard materials, oriented interfaces, and powders embedded in a 5/16-in plastic rod. The device has been used for the ultramicrotomy of meteorite samples, 10-50 micron interplanetary dust particles, and thin films on plastic. Results are presented for a layer lattice silicate from the Murchison carbonaceous chondrite, illustrating the resolution and structural detail that can be obtained with the method.

Blake, D. F.↗

NASA NTRS1988

The use of fluoroepoxy compounds as adhesives to bond fluoroplastics without any surface treatment

The use of fluoroepoxy compounds as adhesives to bond fluoroplastics was investigated. Fluoroepoxy compounds with a F-content higher than 46 percent were able to bond a highly fluorinated plastic such as Teflon PTFE (76 percent F) to give a respectable bond strength without any surface treatment. The advantage of the fluoroepoxy adhesive vanished when applied to a less fluorinated plastic such as Tefzel which contains 55 percent fluorine. Among the curing agents explored, octafluorooctamethylenediamine showed its potential as a cocuring agent for improving both the viscosity of the compound and the flexibility of the cured product.

Lee, Sheng Yen↗

NASA NTRS1989

Detecting Residues On Grit-Blasted Surfaces

Addition of fluorescent or iridescent material to plastic grit particles proposed for detection of grit residues after grit-blast cleaning. Residual films visible by observing grit-blasted surfaces under infrared or ultraviolet light. Plastic grit contains fluorescent or iridescent additive in core and coating. Wherever grit material becomes embedded, additive makes it visible under infrared or ultraviolet light. Applicable to other grit materials, for example fluorescent or iridescent materials added to particles of glass, silicon carbide, aluminum oxide, or zirconium silicate.

Novak, H. L.↗

NASA NTRS1989

Computer-aided design of bevel gear tooth surfaces

This paper presents a computer-aided design procedure for generating bevel gears. The development is based on examining a perfectly plastic, cone-shaped gear blank rolling over a cutting tooth on a plane crown rack. The resulting impression on the plastic gear blank is the envelope of the cutting tooth. This impression and envelope thus form a conjugate tooth surface. Equations are presented for the locus of points on the tooth surface. The same procedures are then extended to simulate the generation of a spiral bevel gear. The corresponding governing equations are presented.

Shuo, Hung Chang↗

NASA NTRS1987

Mechanics of materials model

The Mechanics of Materials Model (MOMM) is a three-dimensional inelastic structural analysis code for use as an early design stage tool for hot section components. MOMM is a stiffness method finite element code that uses a network of beams to characterize component behavior. The MOMM contains three material models to account for inelastic material behavior. These include the simplified material model, which assumes a bilinear stress-strain response; the state-of-the-art model, which utilizes the classical elastic-plastic-creep strain decomposition; and Walker's viscoplastic model, which accounts for the interaction between creep and plasticity that occurs under cyclic loading conditions.

Meister, Jeffrey P.↗

NASA NTRS1988

Fatigue crack closure behavior at high stress ratios

Fatigue crack delay behavior at high stress ratio caused by single peak overloads was investigated in two thicknesses of 7475-T731 aluminum alloy. Closure measurements indicated no closure occurred before or throughout the overload plastic zones following the overload. This was further substantiated by comparing the specimen compliance following the overload with the compliance of a low R ratio test when the crack was fully open. Scanning electron microscope studies revealed that crack tunneling and possibly reinitiation of the crack occurred, most likely a result of crack-tip blunting. The number of delay cycles was greater for the thinner mixed mode stress state specimen than for the thicker plane strain stress state specimen, which is similar to low R ratio test results and may be due to a larger plastic zone for the mixed mode cased.

Turner, C. Christopher↗

NASA NTRS1988

Influence of fatigue crack wake length and state of stress on crack closure

The location of crack closure with respect to crack wake and specimen thickness under different loading conditions was determined. The rate of increase of K sub CL in the crack wake was found to be significantly higher for plasticity induced closure in comparison to roughness induced closure. Roughness induced closure was uniform throughout the thickness of the specimen while plasticity induced closure levels were 50 percent higher in the near surface region than in the midthickness. The influence of state of stress on low-high load interaction effects was also examined. Load interaction effects differed depending upon the state of stress and were explained in terms of delta K sub eff.

Telesman, Jack↗

NASA NTRS1989

Factors influencing the Mode I interlaminar fracture toughness of a rubber toughened thermoplastic matrix composite

The use of a rubber modified thermoplastic resin has been investigated as a method to improve the Mode I interlaminar fracture toughness of a unidirectional continuous carbon fiber composite. Test results show that the improvement in the fracture toughness is less than expected due to rubber particle agglomeration, solvent and molding induced crystallization of the matrix and poor fiber/matrix adhesion. The plastic zone in composites utilizing tough matrices can extend well beyond a single interfibrillar spacing. However, the development of the plastic zone is limited due to the failure of the fiber/matrix interface. In order to fully evaluate the potential of tough composites using toughened matrices, any improvement made in the matrix toughness must be coupled with improvements in the fiber/matrix adhesion.

Parker, D. S.↗

NASA NTRS1990

Dissipation Of Energy In Extension Of Cracks

Dissipation in elastic-plastic material calculated by two-dimensional finite-element method. Analytical procedure developed to calculate various components of dissipation of energy during extension of crack and to relate them to total dissipation of energy computed from global load-displacement response. Observations in study valid for other elastic-plastic fracture situations, including growth of cracks in pressure vessels in nuclear powerplants.

Shivakumar, Kunigal N.↗

NASA NTRS1990

Finite element analysis of structural components using viscoplastic models with application to a cowl lip problem

The viability of advanced viscoplastic models for nonlinear finite element analyses of structural components is investigated. Several uniaxial and a multiaxial problem are analyzed using the finite element implementation of Freed's viscoplastic model. Good agreement between the experimental and calculated uniaxial results validates the finite element implementation and gives confidence to apply it to more complex multiaxial problems. A comparison of results for a sample structural component (the cowl lip of a hypersonic engine inlet) with the earlier elastic, elastic-plastic, and elastic-plastic-creep analyses available in the literature shows that the elastic-viscoplastic analyses yield more reasonable stress and strain distributions. Finally, the versatility of the finite-element-based solution technology presented herein is demonstrated by applying it to another viscoplastic model.

Arya, V. K.↗

NASA NTRS1988

Elevated temperature crack growth

A study was performed to examine the applicability of path-independent (P-I) integrals to crack growth problems in hot section components of gas turbine aircraft engines. Alloy 718 was used and the experimental parameters included combined temperature and strain cycling, thermal gradients, elastic-plastic strain levels, and mean strains. A literature review was conducted of proposed P-I integrals, and those capable of analyzing hot section component problems were selected and programmed into the postprocessor of a finite element code. Detailed elastic-plastic finite element analyses were conducted to simulate crack growth and crack closure of the test specimen, and to evaluate the P-I integrals. It was shown that the selected P-I integrals are very effective for predicting crack growth for isothermal conditions.

Kim, K. S.↗

NASA NTRS1988

Micromechanics of cyclic deformation in SSME turbopump blade materials

Current and candidate Space Shuttle Main Engine (SSME) turbopump blade materials are anisotropic, both in their elastic and plastic response. The major objective is to characterize the plastic deformation behavior of a typical single crystal nickel-base superalloy, PWA 1480, and to use this information to help guide the development of anisotropic constitutive models.

Milligan, Walter W.↗

NASA NTRS1990

A constitutive model for AS4/PEEK thermoplastic composites under cyclic loading

Based on the basic and essential features of the elastic-plastic response of the AS4/PEEK thermoplastic composite subjected to off-axis cyclic loadings, a simple rate-independent constitutive model is proposed to describe the orthotropic material behavior for cyclic loadings. A one-parameter memory surface is introduced to distinguish the virgin deformation and the subsequent deformation process and to characterize the loading range effect. Cyclic softening is characterized by the change of generalized plastic modulus. By the vanishing yield surface assumption, a yield criterion is not needed and it is not necessary to consider loading and unloading separately. The model is compared with experimental results and good agreement is obtained.

Rui, Yuting↗

NASA NTRS1989

Free dendritic growth in viscous melts - Cyclohexanol

Experiments were carried out to measure the growth speed, V, and dendritic tip radius, R, of highly purified cyclohexanol. The data show that VR-squared = constant over the entire experimentally observed supercooling range, Delta T is between 0.1 and 1 K. The stability parameter estimated from this result indicates that sigma(asterisk) = 0.027, a value in good agreement with the values of sigma(asterisk) found for the cubic plastic crystals succinonitrile pivalic acid. Cyclohexanol differs from other carefully measured plastic crystals in that the viscosity of its melt at the melting point is about 20 times higher, so gravity-induced convection remains weak even at small supercoolings.

Singh, N. B.↗