Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle Size Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

The direct effects of strain on burning rates of composite solid propellants

A mathematical model is developed to predict burn rate augmentation due to strain in a composite solid propellant. The model assumes the effect is due to the ability of the flame to penetrate the small fissures and voids that form when a propellant is strained. The number and size of these fissures is obtained by applying a flaw propagation analysis to randomly distributed flaws that form when the binder-oxidizer particle bonds break under stress. A flame height is calculated with Summerfield's burn rate equation and is used to compute the burn rate augmentation based upon the additional burn area created when the flame penetrates the fissures. Comparisons are made with data obtained from published sources. The existence of threshold pressure and strains, above which augmentation occurs, is verified although the model predicts a lower threshold pressure and higher threshold strain than expected. Further results and applications of the model are discussed.

Langhenry, M. T.↗

Airborne particulate matter in spacecraft

Acceptability limits and sampling and monitoring strategies for airborne particles in spacecraft were considered. Based on instances of eye and respiratory tract irritation reported by Shuttle flight crews, the following acceptability limits for airborne particles were recommended: for flights of 1 week or less duration (1 mg/cu m for particles less than 10 microns in aerodynamic diameter (AD) plus 1 mg/cu m for particles 10 to 100 microns in AD); and for flights greater than 1 week and up to 6 months in duration (0.2 mg/cu m for particles less than 10 microns in AD plus 0.2 mg/cu m for particles 10 to 100 microns in AD. These numerical limits were recommended to aid in spacecraft atmosphere design which should aim at particulate levels that are a low as reasonably achievable. Sampling of spacecraft atmospheres for particles should include size-fractionated samples of 0 to 10, 10 to 100, and greater than 100 micron particles for mass concentration measurement and elementary chemical analysis by nondestructive analysis techniques. Morphological and chemical analyses of single particles should also be made to aid in identifying airborne particulate sources. Air cleaning systems based on inertial collection principles and fine particle collection devices based on electrostatic precipitation and filtration should be considered for incorporation into spacecraft air circulation systems. It was also recommended that research be carried out in space in the areas of health effects and particle characterization.

Source record↗

Numerically Modeling the Erosion of Lunar Soil by Rocket Exhaust Plumes

In preparation for the Apollo program, Leonard Roberts of the NASA Langley Research Center developed a remarkable analytical theory that predicts the blowing of lunar soil and dust beneath a rocket exhaust plume. Roberts assumed that the erosion rate was determined by the excess shear stress in the gas (the amount of shear stress greater than what causes grains to roll). The acceleration of particles to their final velocity in the gas consumes a portion of the shear stress. The erosion rate continues to increase until the excess shear stress is exactly consumed, thus determining the erosion rate. Roberts calculated the largest and smallest particles that could be eroded based on forces at the particle scale, but the erosion rate equation assumed that only one particle size existed in the soil. He assumed that particle ejection angles were determined entirely by the shape of the terrain, which acts like a ballistic ramp, with the particle aerodynamics being negligible. The predicted erosion rate and the upper limit of particle size appeared to be within an order of magnitude of small-scale terrestrial experiments but could not be tested more quantitatively at the time. The lower limit of particle size and the predictions of ejection angle were not tested. We observed in the Apollo landing videos that the ejection angles of particles streaming out from individual craters were time-varying and correlated to the Lunar Module thrust, thus implying that particle aerodynamics dominate. We modified Roberts theory in two ways. First, we used ad hoc the ejection angles measured in the Apollo landing videos, in lieu of developing a more sophisticated method. Second, we integrated Roberts equations over the lunar-particle size distribution and obtained a compact expression that could be implemented in a numerical code. We also added a material damage model that predicts the number and size of divots which the impinging particles will cause in hardware surrounding the landing rocket. Then, we performed a long-range ballistics analysis for the ejected particulates.

Source record↗

Instrument Would Detect and Collect Biological Aerosols

A proposed compact, portable instrument would sample micron-sized airborne particles, would discriminate between biological ones (e.g., bacteria) and nonbiological ones (e.g., dust particles), and would collect the detected biological particles for further analysis. The instrument is intended to satisfy a growing need for means of rapid, inexpensive collection of bioaerosols in a variety of indoor and outdoor settings. Purposes that could be served by such collection include detecting airborne pathogens inside buildings and their ventilation systems, measuring concentrations of airborne biological contaminants around municipal waste-processing facilities, monitoring airborne effluents from suspected biowarfare facilities, and warning of the presence of airborne biowarfare agents

Savoy, Steve↗

Scaling properties at freeze-out in relativistic heavy ion collisions

Identified charged pion, kaon, and proton spectra are used to explore the system size dependence of bulk freeze-out properties in Cu+Cu collisions at {radical}s{sub NN} = 200 and 62.4 GeV. The data are studied with hydrodynamically motivated blast-wave and statistical model frameworks in order to characterize the freeze-out properties of the system. The dependence of freeze-out parameters on beam energy and collision centrality is discussed. Using the existing results from Au + Au and pp collisions, the dependence of freeze-out parameters on the system size is also explored. This multidimensional systematic study furthers our understanding of the QCD phase diagram revealing the importance of the initial geometrical overlap of the colliding ions. The analysis of Cu+Cu collisions expands the system size dependence studies from Au+Au data with detailed measurements in the smaller system. The systematic trends of the bulk freeze-out properties of charged particles is studied with respect to the total charged particle multiplicity at midrapidity, exploring the influence of initial state effects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Laser anemometer signals - Visibility characteristics and application to particle sizing

Investigations have been conducted concerning the characteristics of the visibility function as determined by the parameters of the laser anemometer system and the electromagnetic scattering properties of the particles. Experiments have been performed to evaluate the backscatter visibility of signals from a symmetric, s polarization laser anemometer as a function of the particle diameter and a parameter ratio. The results have been compared with the predictions of an analysis based on Mie's scattering theory. The analysis has also been used to evaluate the effects of the collecting aperture's size and location.

Adrian, R. J.↗

Investigation of coal char-slag transition during oxidation: effect of temperature and residual carbon

The transition of coal char to molten slag at high conversion was studied for a bituminous coal using a laminar entrained-flow reactor under oxidizing conditions. Post-oxidized char particles were analyzed by various techniques including loss-on-ignition, gas adsorption analysis, and scanning electron microscopy to determine carbon content, internal surface area and pore size distribution, and char morphology, respectively. These analyses provide information concerning the effect of temperature and residual carbon on the transition from porous char to molten slag. Results showed that, at temperatures above the ash flow temperature, the transition from porous char to molten slag occurred at about 90% conversion for the coal used in this study. No transition occurred at temperatures below the ash flow temperature. This finding explains previous observations that there is a coal-dependent critical carbon conversion at which the ash stickiness increases dramatically. This result also indicates that surface area can be used as a criterion for determining the critical conversion of the transition. In addition, it was found that the randomly overlapping pore model cannot be directly applied to predict the surface area evolution of char particles during the transition without considering the reopening of closed micropores during the initial reaction and the ash fusion effect. 33 refs., 9 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Characterization of ash cenospheres in fly ash from Australian power stations

Ash cenospheres in fly ashes from five Australian power stations have been characterized. The experimental data show that ash cenosphere yield varies across the power stations. Ash partitioning occurred in the process of ash cenosphere formation during combustion. Contradictory to conclusions from the literature, iron does not seem to be essential to ash cenosphere formation in the cases examined in the present work. Further investigation was also undertaken on a series of size-fractioned ash cenosphere samples from Tarong power station. It is found that about 70 wt% of ash cenospheres in the bulk sample have sizes between 45 and 150 {mu}m. There are two different ash cenosphere structures, that is, single-ring structure and network structure. The percentage of ash cenospheres of a network structure increases with increasing ash cenosphere size. Small ash cenospheres (in the size fractions {lt}150 {mu}m) have a high SiO{sub 2}/Al{sub 2}O{sub 3} ratio, and the majority of the ash cenospheres are spherical and of a single-ring structure. Large ash cenosphere particles (in the size fractions of 150-250 {mu}m and {gt}250 {mu}m) have a low SiO{sub 2}/Al{sub 2}O{sub 3} ratio, and a high proportion of the ash cenospheres are nonspherical and of a network structure. A novel quantitative technique has been developed to measure the diameter and wall thickness of ash cenospheres on a particle-to-particle basis. A monolayer of size-fractioned ash cenospheres was dispersed on a pellet, which was then polished carefully before being examined using a scanning electron microscope and image analysis. The ash cenosphere wall thickness broadly increases with increasing ash cenosphere size. The ratios between wall thickness and diameter of ash cenospheres are limited between an upper bound of about 10.5% and a lower bound of about 2.5%, irrespective of the ash cenosphere size. 52 refs., 9 figs., 4 tabs.

01 COAL, LIGNITE, AND PEAT↗

Computationally Guided Development of Components for High Energy Density Solid-State Lithium-Sulfur Batteries

All electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The most challenging of these technical barriers to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria1. The performance metrics for eVTOL craft, such as specific energy, specific power, and safety, exceed those of electric automobiles by a factor of two to four. Current state-of-the-art (SOA) lithium-ion batteries are incapable of meeting the key performance criteria of energy and safety for eVTOL. Therefore, next generation advanced chemistries and designs must be developed to meet required performance metrics for electric aviation2. Beyond lithium-ion chemistries, such as lithium-sulfur, show promise in their high energy, while limitations exist in their power and cyclability due to low electrical conductivity and high intermediate solubility in organic liquid electrolytes. Several strategies to overcome the low electrical conductivity involve the use of selenium as a dopant in the active sulfur material, along with the incorporation of 2-dimensional electron-conducting holey-graphene to improve the composite cathodes electronic conductivity. Furthermore, combining this chemistry with a solid-electrolyte avoids the components’ dissolution issues3. However, the development of composite solid-state cathodes is non-trivial as several components must be intimately mixed so that the active component has sufficient access to both electrons and lithium ions to undergo full electrochemical conversion. Mathematical modeling of battery components can assist experimental design through a robust and rigorous combination of computational modeling techniques covering multiple length scales. The objective is to leverage modern computational materials methods combined with battery multiphysics tools to develop radically advanced compatible cathode and electrolyte materials, build and test solid state lithium-sulfur cells and packs. A NASA-based cross-organizational team of high-powered experts combined integrated computational predictive modeling, fundamental chemistry analysis, advanced material science, and battery cell development to tackle this very challenging, multidisciplinary problem. This presentation will show a multiscale computational modeling approach that has produced a novel particle dynamics method called Solid Electrolyte Sphere Approximation Model (SESAM). SESAM modeling targets the 1-10 µm scale structures and provides electromechanical and grain interactions for predictive design guidelines for the manufacturing of solid-state components. Parameters such as particle size and volume fraction of the constituent materials were modeled and experimentally fabricated to optimize electrochemical performance through improved microstructure design. Experimental feedback was provided through ionic and electronic conductivity assessment and structural analysis of developed materials and cell components.

battery↗

Investigations on the temperature dependent electrical and magnetic properties of NiTiO{sub 3} by molten salt synthesis

Highlights: ► NiTiO{sub 3} particles were synthesized by simple molten salt technique. ► The single phase compound formation was confirmed through XRD analysis. ► The detailed impedance properties of NiTiO{sub 3} were studied at elevated temperature. ► The conductance spectra were fitted using Jonscher Power Law. ► Low temperature magnetization behaviour was explained by core shell model. - Abstract: Submicron-sized NiTiO{sub 3} particles were successfully synthesized by simple molten salt method. The phase purity and crystal structure was confirmed through X-ray diffraction. The characteristics bands of Ni-O and Ti-O were identified using Fourier Transform Infra-red spectrum. The SEM and TEM images shows that the particles are lying in the range of 150–300 nm and selected area electron diffraction pattern (SAED) infers the single crystalline nature of NiTiO{sub 3}. The impedance spectra elucidate the grain interior conducting mechanism and semi-conducting nature of NiTiO{sub 3} at elevated temperatures. The frequency dependent conductance spectra were found to obey Jonscher's power law and a maximum value of conductivity observed was 2 × 10{sup −5} S cm{sup −1} at 520 °C. The magnetic susceptibility measurement infers the antiferromagnetic behavior with the Neel temperature (T{sub N}) of 14.9 K. The increase in coercivity below T{sub N} reveals the coexistence of antiferromagnetic with superparamagnetic behavior. B–H curve represents the first order phase transition from antiferromagnetic to ferromagnetic transition.

36 MATERIALS SCIENCE↗

Investigations of Clouds and Aerosols on Mars, Venus and Titan

This final report was included as part of a new proposal. This new proposal was selected for funding on 9 Nov. 1999. For Titan our interest during the past few years was to explain the observed asymmetry in the albedo. We suggested earlier, from one-dimensional modeling studies, that vertical transport rates were comparable to particle fall speeds. Since heating of the upper atmosphere, which drives dynamical motions, is largely due to the aerosols, a nonlinear interaction between dynamics, radiative heating and particle microphysics is possible. We pursued this interaction in a two-dimensional model. We showed that the observed variations in the albedo between the two hemispheres and over an orbital cycle, could be due to dynamical motions suspending particles so that particle sizes and optical depths vary across the planet. In the Cassini time frame, future studies of this interaction between dynamics, radiation and microphysics may be worthwhile using, the strong modeling base that others, and we have developed. In our recently approved proposal, however, we plan to extend our modeling to hydrocarbon clouds that lie at lower levels. We know very little about such clouds, and numerical models for their properties are non-existent. These clouds may be observed by the Huygen's Probe, and by the Cassini orbiter, so predictions of their properties should help in the analysis of Cassini data. We have also developed a sophisticated model for the lower, condensational, clouds on Venus. In this model we explored the water vapor budget on Venus, and the properties of the clouds such as particle size distribution. During the past few years we have applied our model of the water ice clouds on Mars to new data sets from Pathfinder, and Mars Global Surveyor. We have compared our predictions of cloud properties with those seen by Pathfinder, and found reasonable agreement.

Toon, Owen B.↗

Investigations of Clouds and Aerosols on Mars, Venus and Titan

For Titan our interest during the past few years was to explain the observed asymmetry in the albedo. We suggested earlier, from one-dimensional modeling studies, that vertical transport rates were comparable to particle fall speeds. Since heating of the upper atmosphere, which drives dynamical motions, is largely due to the aerosols, a non- linear interaction between dynamics, radiative heating and particle microphysics is possible. We pursued this interaction in a two-dimensional model. We showed that the observed variations in the albedo between the two hemispheres and over an orbital cycle, could be due to dynamical motions suspending particles so that particle sizes and optical depths vary across the planet. In the Cassini time frame, future studies of this interaction between dynamics, radiation and microphysics may be worthwhile using the strong modeling base that others, and we have developed. In our recently approved proposal, however, we plan to extend our modeling to hydrocarbon clouds that lie at lower levels. We know very little about such clouds, and numerical models for their properties are non-existent. These clouds may be observed by the Huygen's Probe, and by the Cassini orbiter, so predictions of their properties should help in the analysis of Cassini data. We have also developed a sophisticated model for the lower, condensational, clouds on Venus. In this model we explored the water vapor budget on Venus, and the properties of the clouds such as particle size distribution. Most researchers have investigated the upper clouds on Venus, which are essentially a photochemical aerosol with a long lifetime. The lower clouds, however, are similar to stratus clouds on Earth. These clouds have short lifetimes, and are tightly coupled to the dynamics at the base of the Venus cloud deck. We believe that the holes in these clouds seen at near infrared wavelengths by Galileo are related to some interaction between dynamics and cloud physics. One goal of our recently approved proposed work is to better understand this interaction, and to better understand how these clouds may vary if the climate of Venus were to vary. During the past few years we have applied our model of the water ice clouds on Mars to new data sets from Pathfinder, and Mars Global Surveyor. We have compared our predictions of cloud properties with those seen by Pathfinder, and found reasonable agreement. More recently we have improved our model by including a radiative transfer algorithm and a boundary layer transport scheme . The goal of this work is to understand the thermal inversions seen in Mars Global Surveyor data. We find that the inversions are created by clouds radiatively cooling the atmospheric layers in which the clouds form. We have also initiated laboratory work on the physics of carbon dioxide particle formation. In our recently approved work we propose to use these laboratory data, and to extend our modeling to carbon dioxide clouds in the Martian atmosphere.

Toon, Owen B.↗

Preparation and Characterization of Paints and Coatings from Soy and Corn Oils

This project was highly successful. A series of new waterborne polyurethane (PU)/acrylic hybrid latexes were successfully synthesized by the emulsion polymerization of acrylic monomers (butyl acrylate and methyl methacrylate) in the presence of a soybean oil-based waterborne PU dispersion using potassium persulfate as an initiator. The waterborne PU dispersion was synthesized by a polyaddition reaction of toluene 2,4-diisocyanate and a soybean oil-based polyol (SOL). The resulting hybrid latexes, containing 15-60 wt % SOL as a renewable resource, are very stable and exhibit uniform particle sizes of {approx}125 nm as determined by transmittance electronic microscopy. The structure, thermal, and mechanical properties of the resulting hybrid latex films have been investigated by Fourier transform infrared spectroscopy, solid state {sup 13}C NMR spectroscopy, dynamic mechanical analysis, extraction, and mechanical testing. Grafting copolymerization of the acrylic monomers onto the PU network occurs during the emulsion polymerization, leading to a significant increase in the thermal and mechanical properties of the resulting hybrid latexes. This work provides a new way of utilizing renewable resources to prepare environmentally friendly hybrid latexes with high performance for coating applications. In addition, a novel soybean oil-based vinyl-containing waterborne polyurethane (VPU) dispersion has been successfully synthesized from toluene 2,4-diisocyanate, dimethylol propionic acid and a 90:10 mixture of chlorinated soybean oil-based polyol and acrylated epoxidized soybean oil (AESO). Then, a series of VPU/acrylic grafted latexes were prepared by emulsion graft copolymerization of acrylic monomers (40 wt% butyl acrylate and 60 wt% methyl methacrylate) in the presence of the VPU dispersion using potassium persulfate as an initiator. The structure, morphology, and thermal and mechanical properties of the resulting latexes, containing 15-60 wt% soybean oil-based polyols as a renewable resource, were investigated by Fourier transform infrared spectroscopy, solid state {sup 13}C NMR spectroscopy, transmission electron microscopy, thermogravimetric analysis, dynamic mechanical analysis and mechanical testing. The results indicated that graft copolymerization of the acrylic monomers onto the VPU network occurs during emulsion polymerization, leading to a significant increase in the thermal stability and mechanical properties of the resulting miscible grafted latexes. This work provides new environmentally-friendly latexes from a renewable resource with high performance for coating applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Physical characteristics of cometary dust from dynamical studies - A review

Progress made in the determination of the physical characteristics of cometary dust particles from studies of dust tail dynamics is reviewed. Applications of the combined dynamical photometric approach of Finson and Probstein (1968) to studies of cometary tails exhibiting continuous light intensity variations are discussed, with attention given to determinations of the particle-size-related distribution function of the solar radiation pressure exerted on the particles, the contribution of comets to the interplanetary dust, calculations of dust ejection rates and a Monte Carlo approach to the analysis of dust tails. Investigations of dust streamers and striae, which are believed to be related to comet outbursts entailing brief but sharp enhancements of dust production, are then reviewed, with particular attention given to observations of Comet West 1976 VI. Finally, the question of cometary particle type is addressed, and it is pointed out that the presence of submicron absorbing particles in the striae of Comet West is not incompatible with the presence of micron-size dielectric particles in the inner coma.

Sekanina, Z.↗

TESTING OF THE SPINTEK ROTARY MICROFILTER USING ACTUAL HANFORD WASTE SAMPLES

The SpinTek rotary microfilter was tested on actual Hanford tank waste. The samples were a composite of archived Tank 241-AN-105 material and a sample representing single-shell tanks (SST). Simulants of the two samples have been used in non-rad test runs at the 222-S laboratory and at Savannah River National Laboratory (SRNL). The results of these studies are compared in this report. Two different nominal pore sizes for the sintered steel rotating disk filter were chosen: 0.5 and 0.1 {micro}m. The results suggest that the 0.5-{micro}m disk is preferable for Hanford tank waste for the following reasons: (1) The filtrate clarity is within the same range (<<4 ntu for both disks); (2) The filtrate flux is in general higher for the 0.5-{micro}m disk; and (3) The 0.1-{micro}m disk showed a higher likelihood of fouling. The filtrate flux of the actual tank samples is generally in the range of 20-30% compared to the equivalent non-rad tests. The AN-105 slurries performed at about twice the filtrate flux of the SST slurries. The reason for this difference has not been identified. Particle size distributions in both cases are very similar; comparison of the chemical composition is not conclusive. The sole hint towards what material was stuck in the filter pore holes came from the analysis of the dried flakes from the surface of the fouled 0.1-{micro}m disk. A cleaning approach developed by SRNL personnel to deal with fouled disks has been found adaptable when using actual Hanford samples. The use of 1 M nitric acid improved the filtrate flux by approximately two times; using the same simulants as in the non-rad test runs showed that the filtrate flux was restored to 1/2 of its original amount.

36 MATERIALS SCIENCE↗

Hybrid sensor for metal grade measurement of a falling stream of solid waste particles

Highlights: Black-Right-Pointing-Pointer A new sensor system is developed for metal grade measurement of falling bottom ash particles. Black-Right-Pointing-Pointer The system is hybrid, consisting of an optical and an electromagnetic sensor. Black-Right-Pointing-Pointer Grade of ECS concentrated bottom ash in 1-6 mm sieve size accurately measured up to 143 p/s feed rate. Black-Right-Pointing-Pointer Accuracy reached was 2.4% with respect to manual analysis. Black-Right-Pointing-Pointer Measures for elimination of both stationary and stochastic errors are discussed. - Abstract: A hybrid sensor system for accurate detection of the metal grade of a stream of falling solid waste particles is investigated and experimentally verified. The system holds an infrared and an electromagnetic unit around a central tube and counts all the particles and only the metal particles, respectively. The count ratio together with the measured average particle mass ratio (k) of non-metal and metal particles is sufficient for calculation of grade. The performance of the system is accurately verified using synthetic mixtures of sand and metal particles. Towards an application a case study is performed using municipal solid waste incineration bottom ash in size fractions 1-6 mm, which presents a major challenge for nonferrous metal recovery. The particle count ratio was inherently accurate for particle feed rates up to 13 per second. The average value and spread of k for bottom ash was determined as 0.49 {+-} 0.07 and used to calculate grade within 2.4% from the manually analysed grade. At higher feed rates the sensors start missing particles which fall simultaneously through the central tube, but the hybrid system still counted highly repeatable. This allowed for implementation of a count correction ratio to eliminate the stationary error. In combination with averaging in measurement intervals for suppression of stochastic variations the hybrid system regained its accuracy for particle feed rates up to 143 per second. This performance and its special design, intended to render it insensitive to external interference and noise when applied in an eddy current separator, make the hybrid sensor suitable for applications such as quality control and sensor controlled separation.

42 ENGINEERING↗

Aerosol transport and wet scavenging in deep convective clouds: a case study and model evaluation using a multiple passive tracer analysis approach

The effect of wet scavenging on ambient aerosols in deep, continental convective clouds in the mid-latitudes is studied for a severe storm case in Oklahoma during the Deep Convective Clouds and Chemistry (DC3) field campaign. A new passive-tracer based transport analysis framework is developed to characterize the convective transport based on the vertical distribution of several slowly reacting and nearly insoluble trace gases. The passive gas concentration in the upper troposphere convective outflow results from a mixture of 47% from the lower level (0-3 km), 21% entrained from the upper troposphere, and 32% from mid-atmosphere based on observations. The transport analysis framework is applied to aerosols to estimate aerosol transport and wet-scavenging efficiency. Observations yield high overall scavenging efficiencies of 81% and 68% for aerosol mass (Dp < 1μm) and aerosol number (0.03< Dp < 2.5μm), respectively. Little chemical selectivity to wet scavenging is seen among observed submicron sulfate (84%), organic (82%), and ammonium (80%) aerosols, while nitrate has a much lower scavenging efficiency of 57% likely due to the uptake of nitric acid. Observed larger size particles (0.15 - 2.5μm) are scavenged more efficiently (84%) than smaller particles (64%; 0.03 - 0.15μm). The storm is simulated using the chemistry version of the WRF model. Compared to the observation based analysis, the standard model underestimates the wet scavenging efficiency for both mass and number concentrations with low biases of 31% and 40%, respectively. Adding a new treatment of secondary activation significantly improves simulation results, so that the bias in scavenging efficiency in mass and number concentrations is reduced to <10%. This supports the hypothesis that secondary activation is an important process for wet removal of aerosols in deep convective storms.

Yang, Qing↗

Reducing the ordering temperature of CoPt nanoparticles by B additive

We reported the effect of boron addition on magnetic properties and structure of CoPt nanoparticles prepared by a polyol method. The magnetic property measurement showed that the CoPt-B sample exhibited a much larger coercivity compared to the sample without B additive at the same annealing temperature. Transmission electron microscopy and energy dispersive X-ray spectroscopy revealed that the average particle size was about 2 nm for the as-synthesized sample with the ratio of Co and Pt close to 1:1. After annealing, the particle sizes increased but the composition was maintained. The phase transformation of the nanoparticles versus temperature was investigated using a combination of X-ray diffraction and in-situ X-ray absorption analysis. It was shown that the phase transition temperature at which the nanoparticles change from the disordered A1 phase to the ordered L1{sub 0} phase occurs at temperature of 600 °C. We concluded that boron additives could reduce the ordering temperature of CoPt of about 100 °C.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗