Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLOW MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Calculation of flow about posts and powerhead model

A three dimensional analysis of the non-uniform flow around the liquid oxygen (LOX) posts in the Space Shuttle Main Engine (SSME) powerhead was performed to determine possible factors contributing to the failure of the posts. Also performed was three dimensional numerical fluid flow analysis of the high pressure fuel turbopump (HPFTP) exhaust system, consisting of the turnaround duct (TAD), two-duct hot gas manifold (HGM), and the Version B transfer ducts. The analysis was conducted in the following manner: (1) modeling the flow around a single and small clusters (2 to 10) of posts; (2) modeling the velocity field in the cross plane; and (3) modeling the entire flow region with a three dimensional network type model. Shear stress functions which will permit viscous analysis without requiring excessive numbers of computational grid points were developed. These wall functions, laminar and turbulent, have been compared to standard Blasius solutions and are directly applicable to the cylinder in cross flow class of problems to which the LOX post problem belongs.

Anderson, P. G.↗
NASA NTRS1982

Comparison of gas dynamic model with steady solar wind flow around Venus

A gas dynamic model for solar wind flow around Venus has been compared with Pioneer Venus orbiter plasma analyzer measurements from times when the solar wind flow seemed steadiest. The comparisons were made near the terminator. When the observed and model bow shock locations are matched, the model agrees fairly well with the observed parameters: the components of the flow velocity and magnetic field, and the proton number density and isotropic temperature. However, the Mach numbers required to fit the observed bow shock locations are less than 2/3 those estimated from the measured parameters of the free-stream flow, because the bow shock locations (near the terminator) are farther from Venus than expected. Sometimes the measured flow speeds appear to be retarded near the ionopause.

Mihalov, J. D.↗
NASA NTRS2019

Evaluation of a Commercial Surface Vorticity Flow Solver for the Modeling of Propeller-Wing Interaction

A commercially available surface vorticity flow solver’s ability to model propeller-wing interaction effects was evaluated. First, a study was conducted to determine solution sensitivity to simulation parameters. Then, a deflected slipstream experiment was replicated with an actuator disk and wing model. Comparison with experimental data showed that predictions of lift and longitudinal force coefficients matched well at low flap deflections, but experienced offsets in magnitude with increasing flap deflection. Predictions of pitching moment differed significantly from experimental data largely due to the simple actuator disk model being insufficient for capturing the effects of non-zero flow incidence and non-uniform inflow.

Fei, Xiaofan↗
NASA NTRS1991

Overview of aerothermodynamic loads definition study

The objective of the Aerothermodynamic Loads Definition Study is to develop methods of accurately predicting the operating environment in advanced Earth-to-Orbit (ETO) propulsion systems, such as the Space Shuttle Main Engine (SSME) powerhead. Development of time averaged and time dependent three dimensional viscous computer codes as well as experimental verification and engine diagnostic testing are considered to be essential in achieving that objective. Time-averaged, nonsteady, and transient operating loads must all be well defined in order to accurately predict powerhead life. Described here is work in unsteady heat flow analysis, improved modeling of preburner flow, turbulence modeling for turbomachinery, computation of three dimensional flow with heat transfer, and unsteady viscous multi-blade row turbine analysis.

Gaugler, Raymond E.↗
NASA NTRS1991

Second-order closure models for supersonic turbulent flows

Recent work on the development of a second-order closure model for high-speed compressible flows is reviewed. This turbulent closure is based on the solution of modeled transport equations for the Favre-averaged Reynolds stress tensor and the solenoidal part of the turbulent dissipation rate. A new model for the compressible dissipation is used along with traditional gradient transport models for the Reynolds heat flux and mass flux terms. Consistent with simple asymptotic analyses, the deviatoric part of the remaining higher-order correlations in the Reynolds stress transport equations are modeled by a variable density extension of the newest incompressible models. The resulting second-order closure model is tested in a variety of compressible turbulent flows which include the decay of isotropic turbulence, homogeneous shear flow, the supersonic mixing layer, and the supersonic flat-plate turbulent boundary layer. Comparisons between the model predictions and the results of physical and numerical experiments are quite encouraging.

Speziale, Charles G.↗
NASA NTRS1993

Two-dimensional CFD modeling of wave rotor flow dynamics

A two-dimensional Navier-Stokes solver developed for detailed study of wave rotor flow dynamics is described. The CFD model is helping characterize important loss mechanisms within the wave rotor. The wave rotor stationary ports and the moving rotor passages are resolved on multiple computational grid blocks. The finite-volume form of the thin-layer Navier-Stokes equations with laminar viscosity are integrated in time using a four-stage Runge-Kutta scheme. The Roe approximate Riemann solution scheme or the computationally less expensive Advection Upstream Splitting Method (AUSM) flux-splitting scheme are used to effect upwind-differencing of the inviscid flux terms, using cell interface primitive variables set by MUSCL-type interpolation. The diffusion terms are central-differenced. The solver is validated using a steady shock/laminar boundary layer interaction problem and an unsteady, inviscid wave rotor passage gradual opening problem. A model inlet port/passage charging problem is simulated and key features of the unsteady wave rotor flow field are identified. Lastly, the medium pressure inlet port and high pressure outlet port portion of the NASA Lewis Research Center experimental divider cycle is simulated and computed results are compared with experimental measurements. The model accurately predicts the wave timing within the rotor passage and the distribution of flow variables in the stationary inlet port region.

Welch, Gerard E.↗
NASA NTRS1994

Two-dimensional CFD modeling of wave rotor flow dynamics

A two-dimensional Navier-Stokes solver developed for detailed study of wave rotor flow dynamics is described. The CFD model is helping characterize important loss mechanisms within the wave rotor. The wave rotor stationary ports and the moving rotor passages are resolved on multiple computational grid blocks. The finite-volume form of the thin-layer Navier-Stokes equations with laminar viscosity are integrated in time using a four-stage Runge-Kutta scheme. Roe's approximate Riemann solution scheme or the computationally less expensive advection upstream splitting method (AUSM) flux-splitting scheme is used to effect upwind-differencing of the inviscid flux terms, using cell interface primitive variables set by MUSCL-type interpolation. The diffusion terms are central-differenced. The solver is validated using a steady shock/laminar boundary layer interaction problem and an unsteady, inviscid wave rotor passage gradual opening problem. A model inlet port/passage charging problem is simulated and key features of the unsteady wave rotor flow field are identified. Lastly, the medium pressure inlet port and high pressure outlet port portion of the NASA Lewis Research Center experimental divider cycle is simulated and computed results are compared with experimental measurements. The model accurately predicts the wave timing within the rotor passages and the distribution of flow variables in the stationary inlet port region.

Welch, Gerard E.↗
NASA NTRS1990

Control-oriented modeling of combustion and flow processes in liquid propellant rocket engines

This paper presents a control-oriented model of the flow, reaction, and transport processes in liquid propellant rocket combustion chambers, based on the multicomponent conservation laws of gas dynamics. This model provides a framework for the inclusion of detailed chemical kinetic relations, viscous and other dissipative effects, a variety of actuators and sensors, as well as process and measurement disturbances. In addition to its potential usefulness to the designer in understanding the dynamical complexity of the system and the sources of model uncertainty, the model provides a rigorous basis for control system design. An appraisal of current and feasible actuators and sensors, and their mathematical representation are included.

Bentsman, Joseph↗
NASA NTRS2016

Application of a Full Reynolds Stress Model to High Lift Flows

A recently developed second-moment Reynolds stress model was applied to two challenging high-lift flows: (1) transonic flow over the ONERA M6 wing, and (2) subsonic flow over the DLR-F11 wing-body configuration from the second AIAA High Lift Prediction Workshop. In this study, the Reynolds stress model results were contrasted with those obtained from one- and two{equation turbulence models, and were found to be competitive in terms of the prediction of shock location and separation. For an ONERA M6 case, results from multiple codes, grids, and models were compared, with the Reynolds stress model tending to yield a slightly smaller shock-induced separation bubble near the wing tip than the simpler models, but all models were fairly close to the limited experimental surface pressure data. For a series of high-lift DLR{F11 cases, the range of results was more limited, but there was indication that the Reynolds stress model yielded less-separated results than the one-equation model near maximum lift. These less-separated results were similar to results from the one-equation model with a quadratic constitutive relation. Additional computations need to be performed before a more definitive assessment of the Reynolds stress model can be made.

Lee-Rausch, E. M.↗
NASA NTRS1982

Surface tension driven flow in glass melts and model fluids

Surface tension driven flow has been investigated analytically and experimentally using an apparatus where a free column of molten glass or model fluids was supported at its top and bottom faces by solid surfaces. The glass used in the experiments was sodium diborate, and the model fluids were silicone oils. In both the model fluid and glass melt experiments, conclusive evidence was obtained to prove that the observed flow was driven primarily by surface tension forces. The experimental observations are in qualitative agreement with predictions from the theoretical model.

Mcneil, T. J.↗
NASA NTRS1998

Flow Simulation in Secondary Flow Passages of a Rocket Engine Turbopump

This paper presents application of a Generalized Fluid System Simulation Program (GFSSP) to model fluid flow in a very complex secondary flow circuit of a rocket engine turbopump, SIMPLEX. SIMPLEX was a low cost turbopump designed, manufactured and tested to demonstrate the ability to reduce the overall cost and design cycle time of turbomachinery. GFSSP is a general purpose computer program for analyzing flowrate, pressure, temperature and concentration distribution in a complex flow network. The program employs a finite volume formulation of mass, momentum and energy conservation equations in conjunction with thermodynamic equation of state of a real fluid. The secondary flow passages modeled include flow between the impeller shroud and housing, impeller back face and housing, flow through labyrinth seal and bearing, return line flow to inducer and flow adjacent to front and back face of the turbine. Axial load on the bearing are calculated from the predicted pressure on all axial faces of the rotor. The predicted pressure and temperature distributions compared well with the test data.

Schallhorn, Paul↗
NASA NTRSDate not supplied

Wall-modeled LES of Turbulent Flow Over a Two-dimensional Gaussian Bump

We perform wall-modeled large eddy simulations (WMLES) of turbulent flow over a nominally two-dimensional Gaussian-shaped bump geometry to assess its performance in the accelerating and separation regions of the flow. The flow conditions are based on high-fidelity numerical simulation of Uzun & Malik (AIAA Journal 2022). The oncoming flow Mach number is 0.2, with the bump length-based Reynolds number (ReL) of 2 million. In our previous study, while WMLES with the constant coefficient Vreman subgrid scale model and equilibrium wall model performed satisfactorily at lower ReL = 1 million, it failed to predict flow separation at the higher Re, contrary to the experimental observations. We investigate the sensitivity of WMLES to different subgrid scale models, wall models, and grid resolution and topology on flow separation by comparing with available data.

Computational Fluid Dynamics↗
NASA NTRS1991

A near-wall two-equation model for compressible turbulent flows

A near-wall two-equation turbulence model of the K - epsilon type is developed for the description of high-speed compressible flows. The Favre-averaged equations of motion are solved in conjunction with modeled transport equations for the turbulent kinetic energy and solenoidal dissipation wherein a variable density extension of the asymptotically consistent near-wall model of So and co-workers is supplemented with new dilatational models. The resulting compressible two-equation model is tested in the supersonic flat plate boundary layer - with an adiabatic wall and with wall cooling - for Mach numbers as large as 10. Direct comparisons of the predictions of the new model with raw experimental data and with results from the K - omega model indicate that it performs well for a wide range of Mach numbers. The surprising finding is that the Morkovin hypothesis, where turbulent dilatational terms are neglected, works well at high Mach numbers, provided that the near wall model is asymptotically consistent. Instances where the model predictions deviate from the experiments appear to be attributable to the assumption of constant turbulent Prandtl number - a deficiency that will be addressed in a future paper.

Zhang, H. S.↗
NASA NTRS1992

End-to-end modelling of He II flow systems

A practical computer code has been developed which uses the accepted two-fluid model to simulate He II flow in complicated systems. The full set of equations are used, retaining the coupling between the pressure, temperature and velocity fields. This permits modeling He II flow over the full range of conditions, from strongly or weakly driven flow through large pipes, narrow channels and porous media. The system may include most of the components used in modern superfluid flow systems: non-ideal thermomechanical pumps, tapered sections, constrictions, lines with heated side walls and heat exchangers. The model is validated by comparison with published experimental data. It is applied to a complex system to show some of the non-intuitive feedback effects that can occur. This code is ready to be used as a design tool for practical applications of He II. It can also be used for the design of He II experiments and as a tool for comparison of experimental data with the standard two-fluid model.

Mord, A. J.↗
NASA NTRS1983

Evaporation and combustion of sprays

A description is provided of recent spray evaporation and combustion models, taking into account turbulent two- and three-dimensional spray processes found in furnaces, gas turbine combustors, and internal combustion engines. Within the class of spray models of interest, two major categories are distinguished, including locally homogeneous flow (LHF) models and separated flow (SF) models. SF models are of the greatest practical importance, but LHF models have distinct advantages in some cases. Attention is also given to recent progress on modeling interactions between drops and the flow in both dilute and dense sprays, involving sprays having low and high liquid volume fractions, respectively.

Faeth, G. M.↗
NASA NTRS1992

A near-wall two-equation model for compressible turbulent flows

A near-wall two-equation turbulence model of the k-epsilon type is developed for the description of high-speed compressible flows. The Favre-averaged equations of motion are solved in conjunction with modeled transport equations for the turbulent kinetic energy and solenoidal dissipation wherein a variable density extension of the asymptotically consistent near-wall model of So and co-workers is supplemented with new dilatational models. The resulting compressible two-equation model is tested in the supersonic flat plate boundary layer - with an adiabatic wall and with wall cooling - for Mach numbers as large as 10. Direct comparisons of the predictions of the new model with raw experimental data and with results from the K-omega model indicate that it performs well for a wide range of Mach numbers. The surprising finding is that the Morkovin hypothesis, where turbulent dilatational terms are neglected, works well at high Mach numbers, provided that the near wall model is asymptotically consistent. Instances where the model predictions deviate from the experiments appear to be attributable to the assumption of constant turbulent Prandtl number - a deficiency that will be addressed in a future paper.

Zhang, H. S.↗
NASA NTRS1992

Analysis of thermo-chemical nonequilibrium models for carbon dioxide flows

The aerothermodynamics of thermochemical nonequilibrium carbon dioxide flows is studied. The chemical kinetics models of McKenzie and Park are implemented in separate three-dimensional computational fluid dynamics codes. The codes incorporate a five-species gas model characterized by a translational-rotational and a vibrational temperature. Solutions are obtained for flow over finite length elliptical and circular cylinders. The computed flowfields are then employed to calculate Mach-Zehnder interferograms for comparison with experimental data. The accuracy of the chemical kinetics models is determined through this comparison. Also, the methodology of the three-dimensional thermochemical nonequilibrium code is verified by the reproduction of the experiments.

Rock, Stacey G.↗
NASA NTRS2019

Evaluation of Full Reynolds Stress Turbulence Models in FUN3D for Axisymmetric Jet Flow

Two full seven-equation turbulence models available in the FUN3D code are evaluated for their ability to improve the computation of challenging mixing flows encountered in aerospace propulsion. These models are the SSG/LRR and Wilcox full second-moment Reynolds stress models. They solve equations for the six components of the Reynolds stress and a seventh equation for the turbulent length scale. Two standard eddy viscosity models are also evaluated for comparison, the Spalart-Allmaras (SA) one-equation model and the Menter Shear Stress Transport (SST-V) two-equation turbulence model. Flow through an axisymmetric reference nozzle is examined at three flow conditions: subsonic unheated, subsonic heated, and near sonic unheated. Centerline profiles of velocity and turbulent kinetic energy and radial profiles of velocity, turbulent kinetic energy and turbulent stresses are examined. Results showed that the SA model did well at predicting the jet potential core length, but over-mixed the downstream flow, whereas the SST-V model over-predicted the potential core length. The Wilcox-model significantly over-predicted the potential core length and under-predicted the mixing and was not well-suited for the jet flows evaluated, however the SSG/LRR Reynolds stress model did well at predicting the mixing rate and mean velocity for all cases examined.

mixing layers↗