Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engineer Shuttle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Methods used to investigate and resolve the Space Shuttle helium pressure regulator instability

The Space Shuttle main propulsion system (MPS) has seven 750-psia regulators used to purge the Space Shuttle main engines to prevent mixture between oxygen and hydrogen and to pneumatically actuate the propellant valves. Methods used to investigate the instability of the MPS regulators which caused a failure of the 750-psia regulator during a test in 1986 are discussed, with special attention given to the analytical tools and the facilities. As a result of this investigation, a well-understood regulator was designed, with excellent stability over a wide range of inlet pressures from 900 to 4500 psia, flow rates from 1 to 2000 scfm, very fast response, minimal overshoot and undershoot, and durable cycle life. Diagrams of the MPS helium system and of a new -0006 fail-safe improved-stability regulator are presented.

Hurlbert, Eric A.↗
NASA NTRS1990

Rocket combustion chamber life-enhancing design concepts

NASA continues to pursue technologies which can lead to an increase in life and reduce the costs of fabrication of the Space Shuttle Main Engine. The joint NASA/Air Force Advanced Launch System Program has set its prime objectives to be high reliability and low cost for their new advanced booster engine. In order to meet these objectives, NASA will utilize the results of several ongoing programs to provide the required technologies. An overview is presented of those programs which address life enhancing design concepts for the combustion chamber. Seven different design concepts, which reduce the thermal strain and/or increase the material strength of the combustion chamber liner wall are discussed. Subscale rocket test results are presented, where available, for life enhancing design concepts. Two techniques for reducing chamber fabrication costs are discussed, as well as issues relating to hydrocarbon fuels/combustion chamber liner materials compatibility.

Quentmeyer, R. J.↗
NASA NTRS1990

Numerical analysis of secondary flow in a two-stage turbine

The three-dimensional viscous average passage flow in the Pratt and Whitney alternate design Space Shuttle Main Engine fuel turbine has been simulated. The effect of secondary flows generated by upstream blade rows on the performance of downstream blade rows is studied. The numerical results are compared to the design intent to validate improved models in the average passage equations. Analysis of the results centers on the primary spanwise mixing mechanism in this low aspect ratio turbine. A multigrid method has also been incorporated to improve the overall convergence rate of the numerical algorithm.

Kirtley, K. R.↗
NASA NTRS1990

Multi-sensor analysis techniques for SSME safety monitoring

Two algorithms were developed which utilized multi-sensor analysis techniques to complement the current Space Shuttle Main Engine (SSME) safety monitoring system. The first algorithm analyzed the accumulative error between actual and predicted values of the engine parameter set, while the second algorithm combined these error terms into a response pattern and correlated each pattern with a standard pattern. These algorithms were applied to twelve SSME anomalous test firings and were found to produce improved failure detection times in eight of those twelve compared to the current engine safety monitoring system. Of the eight detected anomalous test firings, the first algorithm detected all eight, while the second algorithm detected seven of the eight. No false alarms were indicated by either algorithm for twelve nominal test firings. An initial parametric study of these algorithms for optimized parameter selection is presented and algorithm robustness to sensor failure is demonstrated.

Maul, William A., III↗
NASA NTRS1991

Alignment Tool For Inertia Welding

Compact, easy-to-use tool aligns drive bar of inertia welder over hole in stub. Ensures drive bar concentric to hole within 0.002 in. (0.051 mm.). Holds two batteries and light bulb. Electrical circuit completed, providing current to bulb when pin in contact with post. When pin centered in post hole, it does not touch post, and lamp turns off. Built for use in making repair welds on liquid-oxygen-injector posts in Space Shuttle main engine. Version having suitably modified dimensions used to facilitate alignment in other forests of post.

Snyder, Gary L.↗
NASA NTRS1991

Computing Flow In A Labyrinth Seal

Mathematical model and computer program developed to simulate flow in labyrinth seal. Primary purpose to determine drop in pressure across primary labyrinth seal of high-pressure-oxygen turbopump of Space Shuttle main engine, including portion of drop caused by resistance to flow in gaseous-oxygen drain. Variety of geometries, including multiple chokes, accommodated. Provides for improved study of various types of seal failures and for reviews of mechanics of seal regions. Flexibility of program makes it applicable to other machinery. Further development of program includes providing for lands of various area (variable radius) and improving mathematical model of drain system.

Smith, Tyn S.↗
NASA NTRS1991

Bearing-Cartridge Damping Seal

In proposed design for improved ball-bearing cartridge, damping seal in form of thin-layer fluid journal bearing incorporated into cartridge. Damping seal acts as auxiliary bearing, relieving bearing balls of significant portions of both static and dynamic bearing loads. Damping from seal reduces dynamic loads even further by reducing amplitude of vibrations in second vibrational mode of rotor, which mode occurs when rotor turning at nearly full operating speed. Intended for use in high-pressure-oxygen turbopump of Space Shuttle main engine, also applicable to other turbomachinery bearings.

Goggins, David G.↗
NASA NTRS1989

Marshall Space Flight Center CFD overview

Computational Fluid Dynamics (CFD) activities at Marshall Space Flight Center (MSFC) have been focused on hardware specific and research applications with strong emphasis upon benchmark validation. The purpose here is to provide insight into the MSFC CFD related goals, objectives, current hardware related CFD activities, propulsion CFD research efforts and validation program, future near-term CFD hardware related programs, and CFD expectations. The current hardware programs where CFD has been successfully applied are the Space Shuttle Main Engines (SSME), Alternate Turbopump Development (ATD), and Aeroassist Flight Experiment (AFE). For the future near-term CFD hardware related activities, plans are being developed that address the implementation of CFD into the early design stages of the Space Transportation Main Engine (STME), Space Transportation Booster Engine (STBE), and the Environmental Control and Life Support System (ECLSS) for the Space Station. Finally, CFD expectations in the design environment will be delineated.

Schutzenhofer, Luke A.↗
NASA NTRS1989

Analysis of the SSME HPOTP bearing inlet cavity

Analysis of the flow in the Space Shuttle Main Engine (SSME) high pressure oxygen turbopump (HPOTP) bearing no. 1 inlet cavity was completed in support of return-to-flight. With the incorporation of several design changes in the Phase 2 turbopump, rotordynamic stability of the pumps was enhanced, but the durability and life of the LOX-cooled bearings has decreased. During the post-Challenger SSME recertification, the causes of limited bearing durability were investigated. One topic addressed was the flow environment upstream of the pump-end bearing and the effect of seal exit swirl and a cavity anti-vortex rib on the bearing environment and life. The objective is to define the hydrodynamic environment upstream of the pump-end bearing and determine the effect of seal exit swirl and the anti-vortex rib on bearing inlet swirl. The problem was posed as an axisymmetric cavity flow with the computational domain extending from the seal exit to the bearing inlet. This domain was discretized with 22800 grid points. Boundary conditions were obtained from a 1-D model of the SSME coolant path. The inlet Mach number was 0.19 and the problem was solved with the CMINT code utilizing the Briley-McDonald/Beam-Warming algorithm with preconditioning to speed convergence at low Mach numbers. Three parametric cases with inlet swirl of 50 percent shaft speed (labyrinth seal), 20 percent shaft speed (damping seal), and no inlet swirl were considered. Computational results indicate large vortical flow structures in the cavity, with the labyrinth, damping, and no-swirl cases yielding bearing inlet swirl rates of 14, 10, and 9 percent of shaft speed, respectively. When these results were used as input to the SHABRETH bearing model, limited durability could not be explained by these small differences in swirl. Also, based on these results, a proposed design change for the cavity anti-vortex rib was not implemented by the SSME chief engineer.

Mcconnaughey, P. K.↗
NASA NTRS1989

Turbine stage aerodynamics and heat transfer prediction

A numerical study of the aerodynamic and thermal environment associated with axial turbine stages is presented. Computations were performed using a modification of the unsteady NASA Ames viscous code, ROTOR1, and an improved version of the NASA Lewis steady inviscid cascade system MERIDL-TSONIC coupled with boundary layer codes BLAYER and STAN5. Two different turbine stages were analyzed: the first stage of the United Technologies Research Center Large Scale Rotating Rig (LSRR) and the first stage of the Space Shuttle Main Engine (SSME) high pressure fuel turbopump turbine. The time-averaged airfoil midspan pressure and heat transfer profiles were predicted for numerous thermal boundary conditions including adiabatic wall, prescribed surface temperature, and prescribed heat flux. Computed solutions are compared with each other and with experimental data in the case of the LSRR calculations. Modified ROTOR1 predictions of unsteady pressure envelopes and instantaneous contour plots are also presented for the SSME geometry. Relative merits of the two computational approaches are discussed.

Griffin, Lisa W.↗
NASA NTRS1990

Heat flux measurement in SSME turbine blade tester

Surface heat flux values were measured in the turbine blade thermal cycling tester located at NASA-Marshall. This is the first time heat flux has been measured in a space shuttle main engine turbopump environment. Plots of transient and quasi-steady state heat flux data over a range of about 0 to 15 MW/sq m are presented. Data were obtained with a miniature heat flux gage device developed at NASA-Lewis. The results from these tests are being incorporated into turbine design models. Also, these gages are being considered for airfoil surface heat flux measurement on turbine vanes mounted in SSME turbopump test bed engine nozzles at Marshall. Heat flux effects that might be observed on degraded vanes are discussed.

Liebert, Curt H.↗
NASA NTRS1990

Real-time failure control (SAFD)

The Real Time Failure Control program involves development of a failure detection algorithm, referred as System for Failure and Anomaly Detection (SAFD), for the Space Shuttle Main Engine (SSME). This failure detection approach is signal-based and it entails monitoring SSME measurement signals based on predetermined and computed mean values and standard deviations. Twenty four engine measurements are included in the algorithm and provisions are made to add more parameters if needed. Six major sections of research are presented: (1) SAFD algorithm development; (2) SAFD simulations; (3) Digital Transient Model failure simulation; (4) closed-loop simulation; (5) SAFD current limitations; and (6) enhancements planned for.

Panossian, Hagop V.↗
NASA NTRS1991

Aerodynamics and heat transfer investigations on a high Reynolds number turbine cascade

The results of aerodynamic and heat transfer experimental investigations performed in a high Reynolds number turbine cascade test facility are analyzed. The experimental facility simulates the high Reynolds number flow conditions similar to those encountered in the Space Shuttle Main Engine. In order to determine the influence of Reynolds number on aerodynamic and thermal behavior of the blades, heat transfer coefficients were measured at various Reynolds numbers using liquid crystal temperature measurement technique. Potential flow calculation methods were used to predict the cascade pressure distributions. Boundary layer and heat transfer calculation methods were used with these pressure distributions to verify the experimental results.

Schobeiri, Taher↗
NASA NTRS1991

Blade Tip Rubbing Stress Prediction

An analytical model was constructed to predict the magnitude of stresses produced by rubbing a turbine blade against its tip seal. This model used a linearized approach to the problem, after a parametric study, found that the nonlinear effects were of insignificant magnitude. The important input parameters to the model were: the arc through which rubbing occurs, the turbine rotor speed, normal force exerted on the blade, and the rubbing coefficient of friction. Since it is not possible to exactly specify some of these parameters, values were entered into the model which bracket likely values. The form of the forcing function was another variable which was impossible to specify precisely, but the assumption of a half-sine wave with a period equal to the duration of the rub was taken as a realistic assumption. The analytical model predicted resonances between harmonics of the forcing function decomposition and known harmonics of the blade. Thus, it seemed probable that blade tip rubbing could be at least a contributor to the blade-cracking phenomenon. A full-scale, full-speed test conducted on the space shuttle main engine high pressure fuel turbopump Whirligig tester was conducted at speeds between 33,000 and 28,000 RPM to confirm analytical predictions.

Davis, Gary A.↗
NASA NTRS1991

An evaluation of bearings operating in a cryogenic environment with silicon nitride rolling elements

The bearings used in the space shuttle main engine (SSME) high pressure oxidizer turbopump (HPOTP) do not meet the expected life goals that were set for them. In an effort to improve their performance, many solutions are being studied. New bearing materials are being developed, better manufacturing techniques are being investigated, and improved cage materials for better lubrication are being tested. The focus is on the replacement of steel balls with ones made of silicon nitride in 57-mm HPOTP bearings. The bearings were then installed in a test rig and run at near turbopump operating conditions. The results from this test series are encouraging, with silicon nitride showing good wear resistance and thermal stability.

Gibson, H. G.↗
NASA NTRS1990

Effect of tensile mean stress on fatigue behavior of single-crystal and directionally solidified superalloys

Two nickel base superalloys, single crystal PWA 1480 and directionally solidified MAR-M 246 + Hf, were studied in view of the potential usage of the former and usage of the latter as blade materials for the turbomachinery of the space shuttle main engine. The baseline zero mean stress (ZMS) fatigue life (FL) behavior of these superalloys was established, and then the effect of tensile mean stress (TMS) on their FL behavior was characterized. At room temperature these superalloys have lower ductilities and higher strengths than most polycrystalline engineering alloys. The cycle stress-strain response was thus nominally elastic in most of the fatigue tests. Therefore, a stress range based FL prediction approach was used to characterize both the ZMS and TMS fatigue data. In the past, several researchers have developed methods to account for the detrimental effect of tensile mean stress on the FL for polycrystalline engineering alloys. However, the applicability of these methods to single crystal and directionally solidified superalloys has not been established. In this study, these methods were applied to characterize the TMS fatigue data of single crystal PWA 1480 and directionally solidified MAR-M 246 + Hf and were found to be unsatisfactory. Therefore, a method of accounting for the TMS effect on FL, that is based on a technique proposed by Heidmann and Manson was developed to characterize the TMS fatigue data of these superalloys. Details of this method and its relationship to the conventionally used mean stress methods in FL prediction are discussed.

Kalluri, Sreeramesh↗
NASA NTRS1990

Research reports: 1990 NASA/ASEE Summer Faculty Fellowship Program

Reports on the research projects performed under the NASA/ASEE Summer Faculty Fellowship Program are presented. The program was conducted by The University of Alabama and MSFC during the period from June 4, 1990 through August 10, 1990. Some of the topics covered include: (1) Space Shuttles; (2) Space Station Freedom; (3) information systems; (4) materials and processes; (4) Space Shuttle main engine; (5) aerospace sciences; (6) mathematical models; (7) mission operations; (8) systems analysis and integration; (9) systems control; (10) structures and dynamics; (11) aerospace safety; and (12) remote sensing

Freeman, L. Michael↗
NASA NTRS1990

Bias and uncertainty in the absorption emission measurement of atomic sodium density in the SSME exit plane

The measurement of atomic sodium concentration in the TTB 019 firing of April 1990 is significant in that it represents the first measurement of density at the exit plane of the space shuttle main engine. The knowledge of the sodium density, combined with the certainty that the exit plane of the plume is optically thin at the sodium D-line wavelengths, provides essential information for evaluation of diagnostic techniques using sodium atoms, such as resonant Doppler velocimetry for temperature, pressure, and velocity through high resolution fluorescent lineshape analysis. The technique used for the sodium atom line transmission (SALT) measurements is that of resonant absorption emission using a hollow cathode lamp as the reference source. Through the use of two-dimensional kinetic (TDK) predictions of temperature and density for the flight engine case and radiative transfer calculations, this line-of-sight spectrally integrated transmission indicates a sodium atom concentration, i.e., mole fraction, of 0.91e-10. The subject of this paper is the assumptions and measurement uncertainties tied into the calculation. Because of the narrow shape of the source emission, the uncertainties in the absorption profile could introduce considerable bias in the measurement. The following were investigated: (1) the inclusion of hyperfine splitting of the D-lines in the calculation; (2) the use of the flight engine predictions of plume temperature and density versus those for the large throat engine; (3) the assumption of a Gaussian, i.e., Doppler, distribution for the source radiance with a temperature of 400 K; (4) the use of atomic collisional shift and width values for the work by Jongerius; and (5) a Doppler shift for a 7 degree outward velocity vector at the plume edge. Also included in the study was the bias introduced by an uncertainty in the measurement of the D1/D2 line ratio in the source.

Bauman, Leslie E.↗