Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffraction systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Synthesis of supported silver nano-spheres on zinc oxide nanorods for visible light photocatalytic applications

Highlights: • Synthesis of supported Ag NPs on ZnO nanorods using open vessel microwave reactor. • Use of the Ag/ZnO NPs as an efficient visible light photocatalyst. • Complete degradation of methylene blue in 1 h with 0.5 g/L Ag/ZnO NPs. - Abstract: We report the synthesis of silver (Ag) nano-spheres (NS) supported on zinc oxide (ZnO) nanorods through two step mechanism, using open vessel microwave reactor. Direct reduction of ZnO from zinc nitrates was followed by deposition precipitation of the silver on the ZnO nanorods. The supported Ag/ZnO nanoparticles were then characterized by electron microscopy, X-ray diffraction, FTIR, photoluminescence and UV–vis spectroscopy. The visible light photocatalytic activity of Ag/ZnO system was investigated using a test contaminant, methylene blue (MB). Almost complete removal of MB in about 60 min for doses higher than 0.5 g/L of the Ag/ZnO photocatalyst was achieved. This significant improvement in the photocatalytic efficiency of Ag/ZnO photocatalyst under visible light irradiation can be attributed to the presence of Ag nanoparticles on the ZnO nanoparticles which greatly enhances absorption in the visible range of solar spectrum enabled by surface plasmon resonance effect from Ag nanoparticles.

36 MATERIALS SCIENCE↗

Application of Sorghum Starch for Preparing Superabsorbent

Starch was extracted from Sorghum bicolor grains by alkali steeping method and was utilized for the production of absorbent material by grafting and crosslinking with binary mixtures of vinyl monomers viz. acrylic acid and acrylamide. Both unmodified and modified starches were characterized with Thermogravimetric analysis, Infra-Red spectroscopy, Scanning electron microscopy and X-ray diffraction analysis, to ascertain the modification of the starch. The parameters of the reaction system viz. initiator concentration, monomer concentration, starch to monomer ratio, etc. were optimized. The modified starch showed enhanced water absorption in the range of 49–85 g/g. Absorbency of the products increased after treatment with aqueous alkali solution due to saponification at higher temperature. The saponified products showed increased water absorption level in the range of 245–400 g/g. The product thus obtained using optimized condition of grafting, on saponification found to be highly superabsorbent displaying the water absorbency of 400 g/g. The influence of pH on absorption of water was also tested and best results were obtained at pH 7–8.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Thermodynamic modeling and experimental validation of the Fe-Al-Ni-Cr-Mo alloy system

NiAl-type precipitate-strengthened ferritic steels have been known as potential materials for the steam turbine applications. In this study, thermodynamic descriptions of the B2-NiAl type nano-scaled precipitates and body-centered-cubic (BCC) Fe matrix phase for four alloys based on the Fe-Al-Ni-Cr-Mo system were developed as a function of the alloy composition at the aging temperature. The calculated phase structure, composition, and volume fraction were validated by the experimental investigations using synchrotron X-ray diffraction and atom probe tomography. With the ability to accurately predict the key microstructural features related to the mechanical properties in a given alloy system, the established thermodynamic model in the current study may significantly accelerate the alloy design process of the NiAl-strengthened ferritic steels.

36 MATERIALS SCIENCE↗

High-Pressure Study of Perovskites and Postperovskites in the (Mg,Fe)GeO 3 System

The effect of incorporation of Fe 2+ on the perovskite ( Pbnm ) and postperovskite ( Cmcm ) structures was investigated in the (Mg,Fe)GeO 3 system at high pressures and temperatures using laser-heated diamond anvil cell and synchrotron X-ray diffraction. Samples with compositions of Mg# ≥ 48 were shown to transform to the perovskite (~30 GPa and ~1500 K) and postperovskite (>55 GPa, ~1600-1800 K) structures. Compositions with Mg# ≥ 78 formed single-phase perovskite and postperovskite, whereas those with Mg# < 78 showed evidence for partial decomposition. The incorporation of Fe into the perovskite structure causes a decrease in octahedral distortion as well as a modest decrease in bulk modulus (K 0 ) and a modest increase in zero-pressure volume (V 0 ). It also leads to a decrease in the perovskite-to-postperovskite phase transition pressure by ~9.5 GPa over compositions from Mg#78 to Mg#100.

36 MATERIALS SCIENCE↗

Decoding Li + /Na + Exchange Route Toward High-Performance Mn-Based Layered Cathodes for Li-Ion Batteries

Li + /Na + exchange has been extensively explored as an effective method to prepare high-performance Mn-based layered cathodes for Li-ion batteries, since the first report in 1996 by P. G. Bruce (Nature, 1996. 381, 499–500). Understanding the detailed structural changes during the ion-exchange process is crucial to implement the synthetic control of high-performance layered Mn-based cathodes, but less studied. Herein, in situ synchrotron X-ray diffraction, density functional theory calculations, and electrochemical tests are combined to conduct the systemic studies into the structural changes during the ion-exchange process of an Mn-only layered cathode O3-type Li 0.67 [Li 0.22 Mn 0.78 ]O 2 (LLMO) from the corresponding counterpart P3-type Na 0.67 [Li 0.22 Mn 0.78 ]O 2 (NLMO). The temperature-resolved observations combined with theoretical calculations reveal that the Li + /Na + exchange is favorable thermodynamically and composited with two tandem topotactic phase transitions: 1) from NLMO to a layered intermediate through ≈60% of Li + /Na + exchange. 2) then to the final layered product LLMO through further Li insertion. Moreover, the intermediate-dominate composite is obtained by slowing down the exchange kinetics below room temperature, showing better electrochemical performance than LLMO obtained by the traditional molten-salt method. Finally, the findings provide guides for the synthetic control of high-performance Mn-based cathodes under mild conditions.

25 ENERGY STORAGE↗

Crystal Chemistry of RE 6 Mg x Cd 23- x Pb [0.6(1) ≤ x ≤ 3.2(1); RE = La and Ce]. New Mixed-Metal Derivatives of the RE 6 Cd 23 T Phases ( T = Group 14/15/16 Element)

Synthesis and crystal structure determinations are reported for six quaternary phases with the general formula RE 6 Mg x Cd 23-x Pb [RE = La, Ce; 0.6(1) ≤ x ≤ 3.2(1)]. These compounds were prepared by high temperature reaction of the elements in sealed Nb tubes. As revealed by powder and single-crystal X-ray diffraction, their crystal structures are of the cubic Zr 6 Zn 23 Si system (cF120, Fm 3 m, Z = 4), itself an interstitially filled variant of the Th 6 Mn 23 structure type. Finally, rather than distributing equally across the entire Cd 23 sub-lattice, Mg displayed a tendency to accumulate at specific sites (most notably 4a); charge differences between sites within the sub-lattice, as revealed by computational methods, are the likeliest explanation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electronic structural studies on the improved thermal stability of Li(Ni0.8Co0.15Al0.05)O2 by ZrO2 coating for lithium ion batteries

The electronic structures of bare and ZrO 2 -coated Li(Ni 0.8 Co 0.15 Al 0.05 )O 2 electrode systems were investigated using a combination of time-resolved X-ray diffraction and soft X-ray absorption spectroscopy (XAS) techniques. The ZrO 2 coating on the surface of Li(Ni 0.8 Co 0.15 Al 0.05 )O 2 was effective in elevating the onset temperature of the dissociation of charged Li 0.33 (Ni 0.8 Co 0.15 Al 0.05 )O 2 , which will enhance the safety of Li-ion cells. Lastly, soft XAS spectra of the Ni LII,III-edge in the partial electron yield mode were obtained, which showed that the enhanced electrochemical properties and thermal stability of the cathode materials by ZrO 2 coating can be attributed to the suppression of unwanted Ni oxidation state changes at the surface.

25 ENERGY STORAGE↗

Advantages of tandem versus simultaneous operation: The case of isomerization/hydrogenation of terpinolene epoxide to Terpinen-4-ol using a Ni/TiO 2 -SiO 2 bifunctional catalyst

The conversion of terpinolene epoxide to terpinen-4-ol is a desirable chemical transformation for the production of a valuable intermediate. Here this report describes a one-pot, two-step system for the reaction that uses a bifunctional Ni/TiO 2 -SiO 2 catalyst with isomerization and hydrogenation capabilities. The TiO 2 -SiO 2 serves to isomerize the starting epoxide. The Ni component works to hydrogenate the allylic double bond. The tandem system achieves a high 64% yield of terpinen-4-ol. X-ray diffraction analysis showed that TiO 2 -SiO 2 was a mixed binary oxide, and Fourier transform infrared spectroscopy of adsorbed pyridine suggested that acid sites were mainly Lewis acid sites. Electron microscopy showed that the Ni/TiO 2 -SiO 2 catalyst consisted of spherical particles comprising a titanosilicate phase with highly dispersed zero-valent Ni or anatase on the surface. Additionally, there was strong interaction between Ni and the TiO 2 -SiO 2 mixed oxides. Control kinetic experiments demonstrated that the tandem use of the catalysts was more effective than simultaneous operation.

42 ENGINEERING↗

Re-investigation of high-temperature phase equilibria in Fe-rich Sm–Fe–Ti alloys

Recently renewed attempts to develop high-performance rare-earth-lean permanent magnets based on the Sm(Fe,Ti) 12 compound have drawn attention to the limited knowledge about the high-temperature phase equilibria in the Sm–Fe–Ti system. Experimental investigation of equilibrated alloys with electron probe microanalysis, X-ray diffraction and thermomagnetic analysis revealed several inaccuracies in the currently accepted phase relations at 1000°C and allowed for a revision of the Fe-rich corner of the Sm–Fe–Ti phase diagram. The Sm(Fe,Ti) 12 and Sm 3 (Fe,Ti) 29 phases were found to have more extended Ti ranges of 5.1–9.7 at% and 2.8–6.9 at%, respectively. With increasing of the Ti content, the Curie temperature of the Sm(Fe,Ti) 12 remains nearly constant at 306–312°C, whereas that of the Sm 3 (Fe,Ti) 29 increases from 188°C to 207°C. The low-titanium Sm 3 (Fe,Ti) 29 phase equilibrates not only with the Sm(Fe,Ti) 12 and Sm2(Fe,Ti) 17 phases, but also with (α-Fe) solid solution. Newly demonstrated equilibrium between Sm 2 (Fe,Ti) 17 and TiFe 2 phases makes impossible the earlier reported equilibrium between the Sm 3 (Fe,Ti) 29 and Sm(Fe,Ti) 11 phases. Because of an invariant reaction at 1000 °C, the revised phase diagram also features a class II four-phase equilibrium Sm 3 (Fe,Ti) 29 + TiFe 2 + Sm(Fe,Ti) 12 + Sm 2 (Fe,Ti) 17 . Peritectic decomposition of the Sm(Fe,Ti) 11 phase, which occurs either at 1075°C or at 1087°C, was found to have among its products the Sm(Fe,Ti) 12 phase. Although no such equilibration was attempted, it must be possible to obtain above 1087°C a two-phase state composed of the Sm(Fe,Ti) 12 phase and a liquid – which is important for manufacturing of the Sm(Fe,Ti) 12 - based permanent magnets via the liquid-phase sintering.

36 MATERIALS SCIENCE↗

Experimental determination of zirconium hydride precipitation and dissolution in zirconium alloy

In this study, synchrotron X-Ray transmission diffraction experiments were performed to study hydride precipitation and dissolution in the zirconium/zirconium-hydride system while it occurs. Evidence was found that the hysteresis between the terminal solid solubility for precipitation and dissolution is not observed when hydride particles are already present at the beginning of sample cooldown. Additionally, experimental results show that, during a temperature hold, the concentration of hydrogen in solid solution becomes lower than the terminal solid solubility for hydride precipitation and eventually reaches the terminal solid solubility for hydride dissolution, indicating that the latter is the actual thermodynamic solubility limit.

36 MATERIALS SCIENCE↗

New insights on the formation of supersaturated Cu-Nb solid solution prepared by mechanical alloying

The deformation-driven alloying mechanisms in the immiscible Cu-Nb system during mechanical alloying (MA) process have been studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high-resolution TEM (HRTEM) observations. It is found that the dominating alloying mechanism changes at the different stages of milling. Initially, the alloying process is mainly governed by interfaces and dislocations, which supply fast diffusion channels between phases. In the intermediate stage, Nb particles with sizes below 8 nm undergo a bcc to fcc allotropic transformation, and the interdiffusion between fcc-Nb and fcc-Cu is promoted due to the similarity of lattice structures. Further milling generates disclination defects, which contribute to the formation of fragments or subgrains with sizes below 5 nm. The introduction of such defects and fragments benefits the formation of a complete Cu-Nb solid solution. The formation kinetics of solid solution is analyzed by Johnson-Mehl-Avrami equation, which suggests that the speed of the diffusion of Nb atoms into Cu is very slow. - Highlights: •The bcc to fcc transformation in Nb nanoparticles promotes diffusion process. •The formation of fragments with sizes below 5 nm is attributed to the disclination defects. •Defect-assisted diffusion is responsible for the alloying process.

36 MATERIALS SCIENCE↗

Crystal Growth of Quaternary RE 2 EuSi 2 S 8 ( RE = Ce–Nd, Sm, Gd, Tb) Using Flux-Assisted Boron Chalcogen Mixture (BCM) Method: Investigation of Magnetic and Luminescence Properties

A series of quaternary rare-earth containing thiosilicates with the general formula RE 2 EuSi 2 S 8 (RE = Ce–Nd, Sm, Gd, Tb) has been synthesized via the flux-assisted boron chalcogen mixture (BCM) crystal growth method. High-quality single crystals were obtained, and their crystal structures were determined by single-crystal X-ray diffraction. The RE 2 EuSi 2 S 8 series crystallizes in the trigonal system, adopting the space group R-3c. Polycrystalline samples were employed for physical property measurements, including magnetic susceptibility measurements, UV–visible diffuse reflectance, and photoluminescent response. Magnetic data of RE 2 EuSi 2 S 8 ( RE = Ce, Nd, and Gd) were collected over the 2–300 K temperature range. The samples were paramagnetic behavior with negative Weiss constants (θ W = −11.05, −10.55, and −1.35 K respectively). Their thermal stability was investigated using thermogravimetric analysis (TGA). Optical band gaps, estimated from diffuse reflectance spectra, were determined to be 2.2(1) eV for Ce 2 EuSi 2 S 8 , 1.8(1) eV for Nd 2 EuSi 2 S 8 , and 1.7(1) eV for Gd 2 EuSi 2 S 8 respectively. Finally, photoluminescence measurements were collected on Ce 2 EuSi 2 S 8 and Tb 2 EuSi 2 S 8 single crystals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Revisiting the Polyoxometalate-Based Late-Transition-Metal-Oxo Complexes: The “Oxo Wall” Stands

Terminal oxo complexes of the late transition metals Pt, Pd, and Au have been reported by us in Science and Journal of the American Chemical Society. Despite thoroughness in characterizing these complexes (multiple independent structural methods and up to 17 analytical methods in one case), we have continued to study these structures. Initial work on these systems was motivated by structural data from X-ray crystallography and neutron diffraction and 17O and 31P NMR signatures which all indicated differences from all previously published compounds. With significant new data, we now revisit these studies. New X-ray crystal structures of previously reported complexes K14[P2W19O69(OH2)] and “K10Na3[PdIV(O)(OH)WO(OH2)(PW9O34)2]” and a closer examination of these structures are provided. Also presented are the 17O NMR spectrum of an 17O-enriched sample of [PW11O39]7– and a careful combined 31P NMR-titration study of the previously reported “K7H2[Au(O)(OH2)P2W20O70(OH2)2].” These and considerable other data collectively indicate that previously assigned terminal Pt-oxo and Au-oxo complexes are in fact cocrystals of the all-tungsten structural analogues with noble metal cations, while the Pd-oxo complex is a disordered Pd(II)-substituted polyoxometalate. The neutron diffraction data have been re-analyzed, and new refinements are fully consistent with the all-tungsten formulations of the Pt-oxo and Au-oxo polyoxometalate species.

36 MATERIALS SCIENCE↗

The ultrafast Einstein–de Haas effect

The Einstein-de Haas effect was originally observed in a landmark experiment demonstrating that the angular momentum associated with aligned electron spins in a ferromagnet can be converted to mechanical angular momentum by reversing the direction of magnetization using an external magnetic field. A related problem concerns the timescale of this angular momentum transfer. Experiments have established that intense photoexcitation in several metallic ferromagnets leads to a drop in magnetization on a timescale shorter than 100 femtoseconds—a phenomenon called ultrafast demagnetization. Although the microscopic mechanism for this process has been hotly debated, the key question of where the angular momentum goes on these femtosecond timescales remains unanswered. Here we use femtosecond time-resolved X-ray diffraction to show that most of the angular momentum lost from the spin system upon laser-induced demagnetization of ferromagnetic iron is transferred to the lattice on sub-picosecond timescales, launching a transverse strain wave that propagates from the surface into the bulk. By fitting a simple model of the X-ray data to simulations and optical data, we estimate that the angular momentum transfer occurs on a timescale of 200 femtoseconds and corresponds to 80 per cent of the angular momentum that is lost from the spin system. Finally, our results show that interaction with the lattice has an essential role in the process of ultrafast demagnetization in this system.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

X-Ray Nanointerferometer Based on Si Refractive Bilenses

We report a novel type of x-ray interferometer employing a bilens system consisting of two parallel compound refractive lenses, each of which creates a diffraction limited beam under coherent illumination. By closely overlapping such coherent beams, an interference field with a fringe spacing ranging from tens of nanometers to tens of micrometers is produced. In an experiment performed with 12 keV x rays, submicron fringes were observed by scanning and moire imaging of the test grid. The far field interference pattern was used to characterize the x-ray coherence. Our technique opens up new opportunities for studying natural and man-made nanoscale materials.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Crystal structure of Rb-elpasolite Rb{sub 2}NaAlF{sub 6}

Single crystals of Rb{sub 2}NaAlF{sub 6}, the Rb analogue of the mineral elpasolite, are obtained in the NaF-Rb{sub 2}CO{sub 3}-Al{sub 2}O{sub 3}-Rb{sub 3}PO{sub 4}-H{sub 2}O system under hydrothermal conditions, and their structure is determined by X-ray diffraction (R = 0.0188): a = 8.3087(1) A, space group Fm3bar m, Z = 4, and {rho}{sub calcd} = 3.88 g/cm{sup 3}. The hypothesis that Rb elpasolite exists in nature in late associations of pegmatites enriched in rubidium is proposed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Study of magnetic metal periodic structures by X-Ray and electron microscopy methods

Complex studies of magnetic periodic metallic systems based on Dy/Gd layers have been carried out by X-ray diffraction, resonance X-ray reflectometry, transmission electronic microscopy, and energydispersve microanalysis. The application of these methods and joint analysis of their results provide an effective approach to study of the structure and determination of the parameters of individual layers and interfaces and their structural quality with a high degree of reliability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗