Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Differential Experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Critical Velocity in Open Capillary Channel Flows

We investigate forced liquid flows through open capillary channels with free surfaces experimentally. The experiments were performed under low gravity conditions in the Bremen Drop Tower and on board the sounding rocket TEXUS-37. Open capillary channels (vanes) are used in surface tension tanks to transport the propellant and to provide a flow path for the bubble-free liquid supply to the thrusters. Since the free surfaces can only withstand a certain pressure differential between the liquid and ambient, the flow rate in the channel is limited. The maximum flow rate is achieved when the surfaces collapse and gas is ingested into the outlet. Since experimental and theoretical data of this flow rate limitation is lacking, the safety factors for the application of vanes in surface tension tanks must be unnecessary high. The aim of the investigation is to determine the maximum liquid flow rate and the corresponding critical flow velocity. The characteristic nondimensional parameters, OHNESORGE number, and gap ratio, cover a wide range of usual vanes. For the theoretical approach a one-dimensional momentum balance was set up. The numerical solution yields the maximum volume flux and the position of the free surface in good agreement with the experiments.

Rosendahl, Uwe↗
DOE OSTI2025

Measurement of the top-quark pole mass in dileptonic $t\overline{t}$ + 1-jet events at $\sqrt{s}=13$ TeV with the ATLAS experiment

A measurement of the top-quark pole mass $m$$^{pole}_{t}$ is presented in $t\bar{t}$ events with an additional jet, $t\bar{t}$+ 1-jet, produced in pp collisions at $\sqrt{s} = 13 TeV. The data sample, recorded with the ATLAS experiment during Run 2 of the LHC, corresponds to an integrated luminosity of 140 fb −1 . Events with one electron and one muon of opposite electric charge in the final state are selected to measure the $t\bar{t}$ + 1-jet differential cross-section as a function of the inverse of the invariant mass of the $t\bar{t}$ + 1-jet system. Iterative Bayesian Unfolding is used to correct the data to enable comparison with fixed-order calculations at next-to-leading-order accuracy in the strong coupling. The process pp → $t\bar{t}$j(2 → 3), where top quarks are taken as stable particles, and the process pp → $b\bar{b}$l + vl – $\overline{ν}$j (2 → 7), which includes top-quark decays to the dilepton final state and off-shell effects, are considered. The top-quark mass is extracted using a χ 2 fit of the unfolded normalized differential cross-section distribution. The results obtained with the 2 → 3 and 2 → 7 calculations are compatible within theoretical uncertainties, providing an important consistency check.

Hadron-Hadron Scattering↗
DOE OSTI2024

Test of lepton flavor universality in B ± → K ± μ + μ – and B ± → K ± e + e – decays in proton-proton collisions at $\sqrt{s}$ = 13 TeV

A test of lepton flavor universality in B ± → K ± μ + μ – and B ± → K ± e + e – decays, as well as a measurement of differential and integrated branching fractions of a nonresonant B ± → K ± μ + μ – decay are presented. The analysis is made possible by a dedicated data set of proton-proton collisions at $\sqrt{s}$ = 13 TeV recorded in 2018, by the CMS experiment at the LHC, using a special high-rate data stream designed for collecting about 10 billion unbiased b hadron decays. The ratio of the branching fractions B(B ± → K ± μ + μ – ) to B(B ± → K ± e + e – ) is determined from the measured double ratio R(K) of these decays to the respective branching fractions of the B ± → J/ψK ± with J/ψ → μ + μ – and e + e – decays, which allow for significant cancellation of systematic uncertainties. The ratio R(K) is measured in the range 1.1 < q 2 < 6.0 GeV 2 , where q is the invariant mass of the lepton pair, and is found to be R(K) = 0.78$^{+0.47}_{-0.23}$, in agreement with the standard model expectation R(K) ≈ 1. This measurement is limited by the statistical precision of the electron channel. The integrated branching fraction in the same q 2 range, B(B ± → K ± μ + μ – ) = (12.42 ± 0.68) x 10 -8 , is consistent with the present world-average value and has a comparable precision.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Phase Space Reconstruction from Accelerator Beam Measurements Using Neural Networks and Differentiable Simulations

Characterizing the phase space distribution of particle beams in accelerators is a central part of accelerator understanding and performance optimization. However, conventional reconstruction-based techniques either use simplifying assumptions or require specialized diagnostics to infer high-dimensional (> $2D$) beam properties. In this Letter, we introduce a general-purpose algorithm that combines neural networks with differentiable particle tracking to efficiently reconstruct high-dimensional phase space distributions without using specialized beam diagnostics or beam manipulations. Furthermore, we demonstrate that our algorithm accurately reconstructs detailed 4D phase space distributions with corresponding confidence intervals in both simulation and experiment using a single focusing quadrupole and diagnostic screen. This technique allows for the measurement of multiple correlated phase spaces simultaneously, which will enable simplified 6D phase space distribution reconstructions in the future.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Measurements of Pion and Muon Nuclear Capture at Rest on Argon in the LArIAT Test Beam Experiment

LArIAT is a liquid argon time projection chamber (LArTPC) experiment in a test beam at Fermilab from 2015 to 2017 to understand and characterize interactions of particles in LAr which are commonly observed in neutrino-Ar final-states. Tracks for pions and muons in LArTPCs are difficult to differentiate since both particles exhibit very similar ionization profiles for muon and pion that stop in the TPC. We are exploring unique new particle discrimination capabilities by exploiting information from small, isolated ionization depositions, referred to as "blips", reconstructed near the endpoint of stopping tracks. These blips are formed by gammas emitted when an at-rest pion or muon captures on the argon nucleus. The relatively low beam energy provided by LArIAT makes it uniquely suited for performing this demonstration. In this poster, we present an overview of event candidate selection, blip reconstruction, and background subtraction corresponding to our signal of interest, nuclear captures of pions and muons at rest inside LArIAT's TPC.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Ser 71 Phosphorylation Inhibits Actin-Binding of Profilin-1 and Its Apoptosis-Sensitizing Activity

The essential actin-binding factor profilin-1 (Pfn1) is a non-classical tumor suppressor with the abilities toboth inhibit cellular proliferation and augment chemotherapy-induced apoptosis. Besides actin, Pfn1 interacts with proteins harboring the poly-L-proline (PLP) motifs. Our recent work demonstrated that both nuclear localization and PLP-binding are required for tumor growth inhibition by Pfn1, and this is at least partially due to Pfn1 association with the PLP-containing ENL protein in the Super Elongation Complex (SEC) and the transcriptional inhibition of pro-cancer genes. In this paper, by identifying a phosphorylation event of Pfn1 at Ser 71 capable of inhibiting its actin-binding and nuclear export, we provide in vitro and in vivo evidence that chemotherapy-induced apoptotic sensitization by Pfn1 requires its cytoplasmic localization and actin-binding. With regard to tumor growth inhibition byPfn1, our data indicate a requirement for dynamic actin association and dissociation rendered by reversible Ser 71 phosphorylation and dephosphorylation. Furthermore, genetic and pharmacological experiments showed that Ser 71 of Pfn1 can be phosphorylated by protein kinase A (PKA). Taken together, our data provide novel mechanistic insights into the multifaceted anticancer activities of Pfn1 and how they are spatially-defined in the cell and differentially regulated by ligand-binding.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1971

Experimental physics characteristics of a heavy-metal-reflected fast-spectrum critical assembly

A zero-power critical assembly was designed, constructed, and operated for the purpose of conducting a series of benchmark experiments dealing with the physics characteristics of a UN-fueled, Li-7 cooled, Mo-reflected, drum-controlled compact fast reactor for use with a space-power electric conversion system. The experimental program consisted basically of measuring the differential neutron spectra and the changes in critical mass that accompanied the stepwise addition of (Li-7)3N, Hf, Ta, and W to a basic core fueled with U metal in a pin-type Ta honeycomb structure. In addition, experimental results were obtained on power distributions, control characteristics, neutron lifetime, and reactivity worths of numerous absorber, structural, and scattering materials.

Heneveld, W. H.↗
NASA NTRS1985

Changes in the energy spectrum of anomalous oxygen and helium during 1977-1985

Data was used from the cosmic ray experiment on the Voyager spacecraft to measure the energy spectrum of anomalous O and He during the period 1977 to 1985. These spectra are found to change dramatically after the middle of 1980, with the peak of plateau region of the differential spectrum shifting to a higher energy. This change appears to be related to the reversal of the solar magnetic field and could imply that particle drifts are important to the acceleration of propagation of these particles.

Cummings, A. C.↗
NASA NTRS1986

Sizing an emergency venting system for a cryogenic dewar

If the vacuum vessel that insulates a cryogenic dewar for a spaceborne experiment prior to launch is damaged, air will leak into the vacuum insulation space. As the sudden heat load causes the pressure to rise in the dewar, a safety disk in the emergency vent line will burst at the design pressure differential to allow vaporized cryogenic fluid to escape. The emergency vent line should be sized such that sufficient gaseous cryogen will be vented to keep the pressure inside the dewar below the design limit. On the other hand, the line should not be so large as to impose an unnecessary heat load on the dewar filled with cryogenic fluid. A vent-line computer program was generated to compute the maximum flow rate allowed for a proposed vent-line system. Parametric studies have been carried out for different burst disk pressure differentials, liquid cryogen ullage, and vent-line sizes.

Liu, C. K.↗
NASA NTRS1991

Application of partial differential equation modeling of the control/structural dynamics of flexible spacecraft

Partial differential equations for modeling the structural dynamics and control systems of flexible spacecraft are applied here in order to facilitate systems analysis and optimization of these spacecraft. Example applications are given, including the structural dynamics of SCOLE, the Solar Array Flight Experiment, the Mini-MAST truss, and the LACE satellite. The development of related software is briefly addressed.

Taylor, Lawrence W., Jr.↗
NASA NTRS1994

Heterogeneous Reaction of ClONO2(g) + NaCl(s) to Cl2(g) + NaNO3(s)

The heterogeneous reaction of ClON02 + NaCl yields Cl2 + NaNO3 (eq 1) was investigated over a temperature range 220-300 K in a flow-tube reactor interfaced with a differentially pumped quadrupole mass spectrometer. Partial pressures of ClON02 in the range 10(exp -8) - 10(exp -5) Torr were used. Granule sizes and surface roughness of the NaCl substrates were determined by using a scanning electron microscope, and in separate experiments, surface areas of the substrates were measured by using BET analysis of gas-adsorption isotherms. For dry NaCl substrates, both the decay rates of ClON02 and the growth rates Of C12 were used to obtain reaction probabilities, gamma(sub l) = (4.6 +/- 3.0) x 10(exp -3) at 296 K and (6.7 +/- 3.2) x 10(exp -1) at 225 K, after considering the internal surface area, The error bars represent 1 standard deviation. The Cl2 yield based on the ClONO2 reacted was measured to be 1.0 +/- 0.2. In order to mimic the conditions encountered in the lower stratosphere, the effect of water vapor pressures between 5 x 10(exp -5) and 3 x 10(exp -4) Torr on reaction 1 was also studied. With added H20, reaction probabilities, gamma = (4.1 +/- 2.1) x 10(exp -3) at 296 K and (4.7 +/- 2.9) x 10(exp -3) at 225 K, were obtained. A trace of HOCl, the reaction product from the ClON02 + H20 yield HOCl + HN03 reaction, was observed in addition to the C12 product from reaction 1. The implications of this result for the enhancement of hydrogen chloride in the stratosphere after the El Chichon volcanic eruption and for the marine troposphere are discussed.

Timonen, Raimo S.↗
NASA NTRS1999

Integrated Modeling Tools for Thermal Analysis and Applications

Integrated modeling of spacecraft systems is a rapidly evolving area in which multidisciplinary models are developed to design and analyze spacecraft configurations. These models are especially important in the early design stages where rapid trades between subsystems can substantially impact design decisions. Integrated modeling is one of the cornerstones of two of NASA's planned missions in the Origins Program -- the Next Generation Space Telescope (NGST) and the Space Interferometry Mission (SIM). Common modeling tools for control design and opto-mechanical analysis have recently emerged and are becoming increasingly widely used. A discipline that has been somewhat less integrated, but is nevertheless of critical concern for high precision optical instruments, is thermal analysis and design. A major factor contributing to this mild estrangement is that the modeling philosophies and objectives for structural and thermal systems typically do not coincide. Consequently the tools that are used in these discplines suffer a degree of incompatibility, each having developed along their own evolutionary path. Although standard thermal tools have worked relatively well in the past. integration with other disciplines requires revisiting modeling assumptions and solution methods. Over the past several years we have been developing a MATLAB based integrated modeling tool called IMOS (Integrated Modeling of Optical Systems) which integrates many aspects of structural, optical, control and dynamical analysis disciplines. Recent efforts have included developing a thermal modeling and analysis capability, which is the subject of this article. Currently, the IMOS thermal suite contains steady state and transient heat equation solvers, and the ability to set up the linear conduction network from an IMOS finite element model. The IMOS code generates linear conduction elements associated with plates and beams/rods of the thermal network directly from the finite element structural model. Conductances for temperature varying materials are accommodated. This capability both streamlines the process of developing the thermal model from the finite element model, and also makes the structural and thermal models compatible in the sense that each structural node is associated with a thermal node. This is particularly useful when the purpose of the analysis is to predict structural deformations due to thermal loads. The steady state solver uses a restricted step size Newton method, and the transient solver is an adaptive step size implicit method applicable to general differential algebraic systems. Temperature dependent conductances and capacitances are accommodated by the solvers. In addition to discussing the modeling and solution methods. applications where the thermal modeling is "in the loop" with sensitivity analysis, optimization and optical performance drawn from our experiences with the Space Interferometry Mission (SIM), and the Next Generation Space Telescope (NGST) are presented.

Milman, Mark H.↗
NASA NTRS2022

Continuum Covariance Propagation for Understanding Variance Loss in Advective Systems

Motivated by the spurious variance loss encountered during covariance propagation in atmospheric and other large-scale data assimilation systems, we consider the problem for state dynamics governed by the continuity and related hyperbolic partial differential equations. This loss of variance has been attributed to reduced-rank representations of the covariance matrix, as in ensemble methods for example, or else to the use of dissipative numerical methods. Through a combination of analytical work and numerical experiments, we demonstrate that significant variance loss, as well as gain, typically occurs during covariance propagation, even at full rank. The cause of this unusual behavior is a discontinuous change in the continuum covariance dynamics as correlation lengths become small, for instance in the vicinity of sharp gradients in the velocity field. This discontinuity in the covariance dynamics arises from hyperbolicity: the diagonal of the kernel of the covariance operator is a characteristic surface for advective dynamics. Our numerical experiments demonstrate that standard numerical methods for evolving the state are not adequate for propagating the covariance, because16they do not capture the discontinuity in the continuum covariance dynamics as correlations lengths tend to zero. Our analytical and numerical results show that this leads to significant, spurious variance loss in certain regions, and gain in others. The results suggest that developing local covariance propagation methods designed specifically to capture covariance evolution near the diagonal may prove a useful alternative to current methods of covariance propagation.

covariance propagation↗
DOE OSTI2024

Utah FORGE: Pump and Probe Test on a Mated Fracture Westerly Granite Sample

This dataset contains results from a pump and probe experiment conducted on a mated fracture Westerly Granite sample with a diameter of 1 inch and a height of 2 7/8 inches. The experiment was performed within an aluminum triaxial pressure vessel (TEMCO) to investigate the non-linear acoustic parameters of the sample under varying axial pressures. The confining pressure was maintained at 4 MPa, while the axial pressure was incrementally reduced from 17 MPa to 1 MPa in 1 MPa steps. 5 dynamic pressure oscillations of 0.5 MPa were applied over a 10 minute interval. The dataset includes pump controller data, linear variable differential transformer (LVDT) measurements, and acoustic data. The pump controller data tracks the confining and axial pressures, flow rates, and pump volumes. LVDT measurements provide detailed records of the axial displacement of the cell piston. Additionally, acoustic data captured by s-wave transducers is archived in a compressed file.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Differential ability of three bee species to move genes via pollen

Since the release of genetically engineered (GE) crops, there has been increased concern about the introduction of GE genes into non-GE fields of a crop and their spread to feral or wild cross-compatible relatives. More recently, attention has been given to the differential impact of distinct pollinators on gene flow, with the goal of developing isolation distances associated with specific managed pollinators. To examine the differential impact of bee species on gene movement, we quantified the relationship between the probability of getting a GE seed in a pod, and the order in which a flower was visited, or the cumulative distance traveled by a bee in a foraging bout. We refer to these relationships as ‘seed curves’ and compare these seeds curves among three bee species. The experiments used Medicago sativa L. plants carrying three copies of the glyphosate resistance (GR) allele as pollen donors (M. sativa is a tetraploid), such that each pollen grain carried the GR allele, and conventional plants as pollen recipients. Different foraging metrics, including the number of GR seeds produced over a foraging bout, were also quantified and contrasted among bee species. The lowest number of GR seeds set per foraging bout, and the GR seeds set at the shortest distances, were produced following leafcutting bee visits. In contrast, GR seeds were found at the longest distances following bumble bee visits. Values for honey bees were intermediate. The ranking of bee species based on seed curves correlated well with field-based gene flow estimates. Thus, differential seed curves of bee species, which describe patterns of seed production within foraging bouts, translated into distinct abilities of bee species to move genes at a landscape level. Bee behavior at a local scale (foraging bout) helps predict gene flow and the spread of GE genes at the landscape scale.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1995

The effect of space and parabolic flight on macrophage hematopoiesis and function

We used weak electric fields to monitor macrophage spreading in microgravity. Using this technique, we demonstrated that bone marrow-derived macrophages responded to microgravity within 8 s. We also showed that microgravity differentially altered two processes associated with bone marrow-derived macrophage development. Spaceflight enhanced cellular proliferation and inhibited differentiation. These data indicate that the space/microgravity environment significantly affects macrophages.

NASA Discipline Cell Biology↗
DOE OSTI2025

Nonintrusive projection-based reduced order modeling using stable learned differential operators

Nonintrusive projection-based reduced order models (ROMs) are essential for dynamics prediction in multi-query applications where underlying governing equations are known but the access to the source of the underlying full order model (FOM) is unavailable; that is, FOM is a glass-box. This article proposes a learn-then-project approach for nonintrusive model reduction. In the first step of this approach, high-dimensional stable sparse learned differential operators (S-LDOs) are determined using the generated data. In the second step, the ordinary differential equations, comprising these S-LDOs, are used with suitable dimensionality reduction and low-dimensional subspace projection methods to provide equations for the evolution of reduced states. This approach allows easy integration into the existing intrusive ROM framework to enable nonintrusive model reduction while allowing the use of Petrov–Galerkin projections. The applicability of the proposed approach is demonstrated for Galerkin and LSPG projection-based ROMs through four numerical experiments: 1-D scalar advection, 1-D Burgers, 2-D scalar advection and 1-D scalar advection–diffusion–reaction equations. In conclusion, the results indicate that the proposed nonintrusive ROM strategy provides accurate and stable dynamics prediction.

42 ENGINEERING↗
DOE OSTI2024

A High-Order Eulerian–Lagrangian Runge–Kutta Finite Volume (EL–RK–FV) Method for Scalar Nonlinear Conservation Laws

Abstract We present a class of high-order Eulerian–Lagrangian Runge–Kutta finite volume methods that can numerically solve Burgers’ equation with shock formations, which could be extended to general scalar conservation laws. Eulerian–Lagrangian (EL) and semi-Lagrangian (SL) methods have recently seen increased development and have become a staple for allowing large time-stepping sizes. Yet, maintaining relatively large time-stepping sizes post shock formation remains quite challenging. Our proposed scheme integrates the partial differential equation on a space-time region partitioned by linear approximations to the characteristics determined by the Rankine–Hugoniot jump condition. We trace the characteristics forward in time and present a merging procedure for the mesh cells to handle intersecting characteristics due to shocks. Following this partitioning, we write the equation in a time-differential form and evolve with Runge–Kutta methods in a method-of-lines fashion. High-resolution methods such as ENO and WENO-AO schemes are used for spatial reconstruction. Extension to higher dimensions is done via dimensional splitting. Numerical experiments demonstrate our scheme’s high-order accuracy and ability to sharply capture post-shock solutions with large time-stepping sizes.

Chen, Jiajie↗