Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aircraft Position”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Experiment Description and Results for Arrival Operations Using Interval Management with Spacing to Parallel Dependent Runways (IMSPiDR)

The predicted increase in the number of commercial aircraft operations creates a need for improved operational efficiency. Two areas believed to offer increases in aircraft efficiency are optimized profile descents and dependent parallel runway operations. Using Flight deck Interval Management (FIM) software and procedures during these operations, flight crews can achieve by the runway threshold an interval assigned by air traffic control (ATC) behind the preceding aircraft that maximizes runway throughput while minimizing additional fuel consumption and pilot workload. This document describes an experiment where 24 pilots flew arrivals into the Dallas Fort-Worth terminal environment using one of three simulators at NASA?s Langley Research Center. Results indicate that pilots delivered their aircraft to the runway threshold within +/- 3.5 seconds of their assigned time interval, and reported low workload levels. In general, pilots found the FIM concept, procedures, speeds, and interface acceptable. Analysis of the time error and FIM speed changes as a function of arrival stream position suggest the spacing algorithm generates stable behavior while in the presence of continuous (wind) or impulse (offset) error. Concerns reported included multiple speed changes within a short time period, and an airspeed increase followed shortly by an airspeed decrease.

Baxley, Brian T.↗
NASA NTRS2014

Effect of Control System Augmentation on Handling Qualities and Task Performance in Good and Degraded Visual Environments

In June 2013, NASA and the U.S. Army jointly conducted a simulation experiment in the NASA-Ames Vertical Motion Simulator that examined and quantified the effects of limited-authority control system augmentation on handling qualities and task performance in both good and degraded visual environments (DVEs). The vehicle model used for the experiment was the OH-58D with similar size, weight and performance, and the same 4-blade rotor system as the Bell 407 civilian helicopter that is commonly used for medical evacuation and emergency medical services. The control systems investigated as part of this study included the baseline aircraft Rate Command system, a short-term Attitude Command/Attitude Hold system that uses lagged-rate feedback to provide a short-term attitude response, Modernized Control Laws that provide an Attitude Command/Attitude Hold control response type, and Modernized Control Laws with an additional Position Hold function. Evaluation tasks included the ADS-33 Hover, Sidestep, Acceleration/Deceleration, and Pirouette Mission Task Elements, as well as a new proposed Emergency Medical Services task that includes an approach and landing at a minimally prepared remote landing site. Degraded visual environments were simulated with night vision goggles and an unaided night scene. A total of nine experimental test pilots participated in the four-week simulation experiment. Data recorded during the evaluation included Cooper-Harper handling qualities ratings, Bedford Workload scale ratings, and task performance. The Usable Cue Environment (UCE) was measured for this simulation experiment, and found to be UCE equals 1 in good visual environments and UCE equals 2 in degraded visual environments with night vision goggles. Results showed that handling qualities ratings were improved with a control system providing short-term attitude response over a rate command system, although the improvements were not sufficient to produce Level 1 handling qualities in degraded visual environments. Results for an Attitude Command/Attitude Hold control system showed that borderline Level 1 handling qualities could be achieved in degraded visual environments, and the 10 percent authority stability augmentation system was adequate to obtain these handling qualities ratings.

Handling Qualities↗
NASA NTRS2004

Deployment of a Fast-GCMS System to Measure C2 to C5 Carbonyls, Methanol and Ethanol Aboard Aircraft

Through funding of this proposal, a fast response gas chromatograph/mass spectrometer (FGCMS) instrument to measure less than or equal to C4 carbonyl compounds and methanol was developed for the NASA GTE TRACE-P (Global Tropospheric Experiment, Transport And Chemical Evolution Over The Pacific) mission. The system consists of four major components: sample inlet, preconcentration system, gas chromatograph (GC), and detector. The preconcentration system is a custom-built cryogen-conservative system. The GC is a compact, custom-built unit that can be temperature programmed and rapidly cooled. Detection is accomplished with an Agilent Technologies 5973 mass spectrometer. The FGCMS instrument provides positive identification because the compounds are chromatographically separated and mass selected. During TRACE-P, a sample was analyzed every 5 minutes. The FGCMS limit of detection was between 5 and 75 pptv, depending on the compound. The entire instrument package is contained in a standard NASA instrument rack (106 cm x 61 cm x 135 cm), consumes less than 1200 watts and is fully automated with LabViEW 6i. Methods were developed or producing highly accurate gas phase standards for the target compounds and for testing the system in the presence of potential interferents. This report presents data on these tests and on the general overall performance of the system in the laboratory and aboard the DC-8 aircraft during the mission. Vertical profiles for acetaldehyde, methanol, acetone, propanal, methyl ethyl ketone, and butanal from FGCMS data collected over the entire mission are also presented.

Apel, Eric C.↗
NASA NTRS2017

Steady State Thermal Analyses of SCEPTOR X-57 Wingtip Propulsion

Electric aircraft concepts enable advanced propulsion airframe integration approaches that promise increased efficiency as well as reduced emissions and noise. NASA's fully electric Maxwell X-57, developed under the SCEPTOR program, features distributed propulsion across a high aspect ratio wing. There are 14 propulsors in all: 12 high lift motor that are only active during take off and climb, and 2 larger motors positioned on the wingtips that operate over the entire mission. The power electronics involved in the wingtip propulsion are temperature sensitive and therefore require thermal management. This work focuses on the high and low fidelity heat transfer analysis methods performed to ensure that the wingtip motor inverters do not reach their temperature limits. It also explores different geometry configurations involved in the X-57 development and any thermal concerns. All analyses presented are performed at steady state under stressful operating conditions, therefore predicting temperatures which are considered the worst-case scenario to remain conservative.

Thermal↗
NASA NTRS1973

Study of application of ERTS-A imagery to fracture-related mine safety hazards in the coal mining industry

The author has identified the following significant results. The Kings Station Mine in Gibson County, Indiana has experienced considerable roof fall problems. Detailed fracture mapping of the mine area was done with ERTS-1 and aircraft imagery, and a prediction map of roof problem areas was produced in advance of a visit. The visit to the mine and discussions with the operator indicated that of four zones mapped as potential problem areas, three coincided with areas of excessive roof fall. This positive correlation of 75% lends confidence to the validity of the technique being applied in the investigation. The mine officials expressed an interest in the project and are anxious to see the final product maps which are forthcoming.

Wier, C. E.↗
NASA NTRS1987

Cockpit Resource Management (CRM) training in the 349th military airlift wing

CRM training can be done on a limited budget. It seems that everyone has a special name for their CRM program. A new program was created and entitled, Aircrew Resource Management (ARM) to emphasize the use of the full resources on our aircraft. That is meant to specifically include the loadmasters. The name also emphasizes the concept that all crewmembers are responsible for safe completion of the trip. The loadmasters have been the brightest students to date. They are a classic under-utilized resource. Together, their crew position has been credited with more ARM saves than the engineers and pilots. The seminar-based program is run by two seminar facilitators that is reinforced by Line Oriented Flight Training sessions run by the active-duty counterparts.

Halliday, John T.↗
NASA NTRS1989

Flight Balance For Skin-Friction Measurements

Skin-friction balance (flight balance) for use in flight on aircraft fuselage incorporates type-one, closed-loop control to make direct skin-friction force measurements. Curved surface element 2 in. (5.08 cm) in diameter used to sense tangential force of airstream passed over it. Linear electromagnetic force motor exerts restoring force that nulls position of sensing element. Applied skin-friction force measured by sensing amount of current through motor necessary to maintain null position. Unit is rugged, accurate, reliable, and easy to operate. Insensitivity of balance to background rectilinear vibrations and ability to sustain large transient loads during takeoffs and landings make it attractive for flight testing.

Tcheng, Ping↗
NASA NTRS1988

Flight measured downwash of QSRA

Several reports have been written on the performance of the Quiet Short-Haul Research Aircraft, which shows the advantages of upper-surface blowing or the propulsive-lift wing as it applies to lift, maneuverability, and short takeoff and landing. This high lift generation at low speeds results in substantial downwash, especially in the low-aft fuselage tail position. The high T-tail of the Quiet Short-Haul Research Aircracft minimizes the undesirable downwash effects from the propulsive-lift wing. Queries from Department of Defense agencies and industry for quantitative values prompted a series of flight-measured downwash tests at the high T-tail and the low aft fuselage position. The results are presented in a summarized format, showing downwash, Delta epsilon/Delta a, for both locations. As would be expected, downwash increases for increased power and USB flap settings. The downwash is greater in the low aft-fuselage position as compared to the high T-tail area.

Eppel, Joseph C.↗
NASA NTRS1990

Airborne water vapor DIAL system development

A differential absorption lidar (DIAL) system developed at NASA Langley Research Center for the remote measurement of atmospheric H2O and aerosols from an aircraft is briefly discussed. This DIAL system utilizes a Nd:YAG laser-pumped dye laser as the off-line transmitter and a narrowband, tunable Alexandrite laser as the on-line transmitter. A 1-m monochromator and a multipass absorption cell are used to position the on-line laser to the center of the H2O line. The receiver system has a 14-in. diameter, f/7 Celestron telescope to collect the backscattered laser light and focus in into the detector optics. Return signals are converted to electrical signals by the optical detector and are digitalized and stored on magnetic tape. The results of fligh tests of the system are shown.

Higdon, Noah S.↗
NASA NTRS2000

GPS Signal Scattering from Sea Surface: Wind Speed Retrieval Using Experimental Data and Theoretical Model

Global Positioning System (GPS) signals reflected from the ocean surface have potential use for various remote sensing purposes. Some possibilities arc measurements of surface roughness characteristics from which ware height, wind speed, and direction could be determined. For this paper, GPS-reflected signal measurements collected at aircraft altitudes of 2 km to 5 km with a delay-Doppler mapping GPS receiver arc used to explore the possibility of determining wind speed. To interpret the GPS data, a theoretical model has been developed that describes the power of the reflected GPS signals for different time delays and Doppler frequencies as a function of geometrical and environmental parameters. The results indicate a good agreement between the measured and the modeled normalized signal power waveforms during changing surface wind conditions. The estimated wind speed using surface- reflected GPS data, obtained by comparing actual and modeled waveforms, shows good agreement (within 2 m/s) with data obtained from a nearby buoy and independent wind speed measurements derived from the TOPEX/Poseidon altimetric satellite.

Komjathy, Attila↗
NASA NTRS1995

Cascade Optimization Strategy Maximizes Thrust for High-Speed Civil Transport Propulsion System Concept

The design of a High-Speed Civil Transport (HSCT) air-breathing propulsion system for multimission, variable-cycle operations was successfully optimized through a soft coupling of the engine performance analyzer NASA Engine Performance Program (NEPP) to a multidisciplinary optimization tool COMETBOARDS that was developed at the NASA Lewis Research Center. The design optimization of this engine was cast as a nonlinear optimization problem, with engine thrust as the merit function and the bypass ratios, r-values of fans, fuel flow, and other factors as important active design variables. Constraints were specified on factors including the maximum speed of the compressors, the positive surge margins for the compressors with specified safety factors, the discharge temperature, the pressure ratios, and the mixer extreme Mach number. Solving the problem by using the most reliable optimization algorithm available in COMETBOARDS would provide feasible optimum results only for a portion of the aircraft flight regime because of the large number of mission points (defined by altitudes, Mach numbers, flow rates, and other factors), diverse constraint types, and overall poor conditioning of the design space. Only the cascade optimization strategy of COMETBOARDS, which was devised especially for difficult multidisciplinary applications, could successfully solve a number of engine design problems for their flight regimes. Furthermore, the cascade strategy converged to the same global optimum solution even when it was initiated from different design points. Multiple optimizers in a specified sequence, pseudorandom damping, and reduction of the design space distortion via a global scaling scheme are some of the key features of the cascade strategy. HSCT engine concept, optimized solution for HSCT engine concept. A COMETBOARDS solution for an HSCT engine (Mach-2.4 mixed-flow turbofan) along with its configuration is shown. The optimum thrust is normalized with respect to NEPP results. COMETBOARDS added value in the design optimization of the HSCT engine.

Source record↗
NASA NTRS1982

Measurements of the Fuel Mileage of a KC-135 Aircraft with and Without Winglets

The KC-135A Winglet Flight Research and Demonstration Program was a joint effort of the Air Force, NASA and the Boeing Military Airplane Company to flight test winglets on the KC-135A. The primary objective of the program was to verify the cruise performance improvements predicted by analysis and wind tunnel tests. Flight test data were obtained for winglets positioned at 15 deg cant/-2 deg incidence, 0 deg cant/-4 deg incidence, 15 deg cant/-4 deg incidence and for winglets off (baseline). Both fuel mileage and drag measurements were obtained. The 15 deg cant/-4 deg incidence winglet configuration provided the greatest performance improvement. The flight test measured fuel mileage improvement for a 0.78 Mach number was 3.1 percent at 8 x 10(5) pounds W/delta and 5.5 percent at 1.05 x 10(6) pounds W/delta. Correcting the flight measured data for surface pressure differences between wind tunnel and flight resulted in a fuel mileage improvement of 4.4 percent at 8 x 10(5) pounds W/delta and 7.2 percent at 1.05 x 10(6) pounds W/delta. The agreement between the fuel mileage and drag data was excellent.

Temanson, G. E.↗
NASA NTRS1975

Flight test investigation of the vortex wake characteristics behind a Boeing 727 during two-segment and normal ILS approaches

A series of flight tests were performed to evaluate the vortex wake characteristics of a Boeing 727 (B727-200) aircraft during conventional and two-segment ILS approaches. Flights of the B727, equipped with smoke generators for vortex marking, were flown wherein its vortex wake was intentionally encountered by a Lear Jet model 23 (LR-23) or a Piper Twin Comanche (Pa-30); and its vortex location during landing approach was measured using a system of photo-theodolites. The tests showed that at a given separation distance there were no differences in the upsets resulting from deliberate vortex encounters during the two types of approaches. Timed mappings of the position of the landing configuration vortices showed that they tended to descend approximately 91 meters (300 feet) below the flight path of the B727. The flaps of the B727 have a dominant effect on the character of the trailed wake vortex. The clean wing produces a strong, concentrated vortex. As the flaps are lowered, the vortex system becomes more diffuse. Pilot opinion and roll acceleration data indicate that 4.5 nautical miles would be a minimum separation distance at which roll control could be maintained during parallel encounters of the B727's landing configuration wake by small aircraft.

Garodz, L. J.↗
DOE OSTI2021

Analysis of secondary organic aerosol simulation bias in the Community Earth System Model (CESM2.1)

Organic aerosol (OA) has been considered as one of the most important uncertainties in climate modeling due to the complexity in presenting its chemical production and depletion mechanisms. To better understand the capability of climate models and probe into the associated uncertainties in simulating OA, we evaluate the Community Earth System Model version 2.1 (CESM2.1) configured with the Community Atmosphere Model version 6 (CAM6) with comprehensive tropospheric and stratospheric chemistry representation (CAM6-Chem) through a long-term simulation (1988–2019) with observations collected from multiple datasets in the United States. We find that CESM generally reproduces the interannual variation and seasonal cycle of OA mass concentration at surface layer with a correlation of 0.40 compared to ground observations and systematically overestimates (69%) in summer and underestimates (-19%) in winter. Through a series of sensitivity simulations, we reveal that modeling bias is primarily related to the dominant fraction of monoterpene-formed secondary organic aerosol (SOA), and a strong positive correlation of 0.67 is found between monoterpene emission and modeling bias in the eastern US during summer. In terms of vertical profile, the model prominently underestimates OA and monoterpene concentrations by 37%–99% and 82%–99%, respectively, in the upper air (>500 m) as validated against aircraft observations. Our study suggests that the current volatility basis set (VBS) scheme applied in CESM might be parameterized with monoterpene SOA yields that are too high, which subsequently results in strong SOA production near the emission source area. We also find that the model has difficulty in reproducing the decreasing trend of surface OA in the southeastern US probably because of employing pure gas VBS to represent isoprene SOA which is in reality mainly formed through multiphase chemistry; thus, the influence of aerosol acidity and sulfate particle change on isoprene SOA formation has not been fully considered in the model. This study reveals the urgent need to improve the SOA modeling in climate models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1997

The Relationship of Subvisible Cirrus Clouds Observed During NASA's Tropical Ozone

Thin, subvisible cirrus (SVC) clouds at the tropical tropopause have been observed by a number of methods in a variety of observational programs, including in situ sampling and aircraft and space-based lidar. Modeling studies suggest that these clouds play an important role in dehydrating tropospheric air as it enters the stratosphere. This is because particles large enough to have significant fall speeds can form under the conditions of slow cooling that are implied by the large horizontal extent of the SVC sheets. The IRA radiation that these clouds absorb, and the upward vertical motion this implies, also make them candidates for a tropical troposphere-to-stratosphere mass transfer mechanism. These sheets were observed on five flights during the Tropical Ozone Transport Experiment (TOTE) by the NASA Langley DIAL lidar aboard NASA's DC-8 research aircraft, operating during December 1995 and February 1996 south of Hawaii (12 S to 21 N). This experiment provided a unique look at these clouds since temperature profiles were available for all the SVC observations. Thus, the observed distributions of SVC's can be compared with the position of the tropopause to establish whether the SVC's are tropospheric or stratospheric. It also allows comparison of TOTE observations with in situ experiments, where water and cloud particle data is available as a function of temperature and potential temperature.

Pfister, L.↗
NASA NTRS1999

Navigating the Airways

Through a licensing agreement with JPL, Hughes Aircraft Company is using the Jet Propulsion Laboratory's (JPL) software GIPSY-OASIS for implementation of the Federal Aviation Administration's Wide Area Augmentation System (WAAS). WAAS will provide precision navigation for commercial airliners in U.S. airspace. JPL's GIPSY-OASIS (GIPSY - GPS-Inferred Positioning System; OASIS - Orbit Analysis and Simulation Software) has been used world-wide to produce the most accurate Global Positioning System (GPS) ephemeredes (satellite position) solutions ever achieved for ground and space users, both in scientific and commercial applications.

Source record↗
NASA NTRSDate not supplied

Designing for Advanced Aerial Mobility: Human-Autonomy Teaming and In-Time System-Wide Safety Assurance

The continued growth of aviation shall require new innovative technologies and operational concepts to meet the ever-increasing demands on air transportation. The NASA Advanced Air Mobility (AAM) project focuses on emerging aviation markets, such as Urban Air Mobility (UAM). UAM is defined as “...a safe and efficient system for air passenger and cargo transportation within an urban area. It is inclusive of small package delivery and other urban unmanned aerial system services and supports a mix of onboard/ground-piloted and increasingly autonomous operations” ([1]). The AAM project emphasizes technology development and validating system-level concepts and solutions in coordination with other NASA Aeronautics Research Mission Directorate (ARMD) projects to enable UAM metro- and micro-plex vertiport and airspace concepts of operations. The NASA AAM research portfolio includes the concepts of Remote Supervisor-in-Command (RSC) and Fleet and Airspace Manager (FAM) as possible human roles for consumer fleet providers. NASA research in RSC is focused on development of guidelines and standards for remote pilots/operators passively and actively controlling a large fleet of autonomous aircraft. For FAM, flight and ground system concepts and technologies to enable high density homogeneous operations at increased scale from vertiport(s), and coordination with other humans in the systems (e.g., UAM urban airspace manager, Air Traffic Control) are key research areas. The envisioned UAM operations are posited to require autonomous systems to enable functions ranging from fleet and resource management to vehicle control. Although automation has become increasingly sophisticated and ubiquitous in civil aviation, autonomy represents a significant evolution in automation, which has generally been limited in functional scope and capability. As autonomy takes on increasing responsibilities, humans and machines will be required to work together in new and different ways [2], rather than traditional design approaches focused on how machines (i.e., autonomy) can do the work of people. The emerging field of human-autonomy teaming (HAT) represents a comprehensive and prioritized research-driven approach to enable the success of future emerging aviation market applications through capabilities and principles that facilitate humans and machine working and thinking better together. The NASA Transformational Tools and Technologies (TTT) Autonomous System (AS) Sub-project was created to assist with the transition into higher levels of autonomy to enable new modes of air transportation, such as UAM. TTT-AS has identified HAT as a key research need to enable UAM while maintaining today’s ultra-safe aviation system safety levels. The latter challenge has been taken up by the NASA System-Wide Safety (SWS) Project, which recognizes that aviation safety, as it evolves, shall require new ways of thinking about safety to include integration of a wide-range of existing and new safety systems and practices, enhanced tools and technologies, increased access to data and data fusion, improved data analysis capabilities, enhanced in-time risk monitoring and detection, hazard prioritization and mitigation, safety assurance decision-support, and in-time integrated system analytics [3].The operational concept of UAM represents a variety of work that has been termed, “work-as-imagined” to characterize the idea that how people think that work is done and how work is actually done are often not the same [4]. To ensure design success and system safety, looking at “work-as-done” provides a comparative approach toward UAM concept and technology design through examination of corresponding analogs found today in aviation (e.g., on-demand operations) and other transportation domains (e.g., port operations). The paper shall discuss various alternative applications with specific focus on airline operation center (AOC) operations, and unmanned aerial system (UAS) command-and-control to inform scaled-versions of FAM and RSC, respectively, and with consideration of the national airspace system contextual environment. The tenets and principles of the HAT field and current NASA research efforts under the TTT-AS sub-project shall also be described. Finally, the SWS sub-project efforts to develop In-Time System-Wide Safety Assurance (ISSA) and In-Time Safety Management Systems (IASMS) are discussed in terms of how “in-time” safety assurance may be conceptualized for the on-demand mobility air taxi “work-as-imagined” operational concept [5]. As part of this effort, concepts from the emerging field of resilience engineering, are being studied. Traditional approaches to aviation safety have focused on what can go wrong and how to prevent it. Another approach to thinking about system safety should reflect not only “avoiding things that go wrong” (protective safety) but also “ensuring that things go right” (productive safety), that enables a system to exhibit the resilient performance [6] necessary for the success of the future aviation system emerging concepts of operations. The paper shall describe efforts focused on how productive safety and resilience may enable a more complete approach to system safety thinking and design of ISSA and IASMS for UAM. Future directions and research needs shall also be discussed.

resilience↗
NASA NTRS2017

Flight Crew Survey Responses from the Interval Management (IM) Avionics Phase 2 Flight Test

The Interval Management (IM) Avionics Phase 2 flight test used three aircraft over a nineteen day period to operationally evaluate a prototype IM avionics. Quantitative data were collected on aircraft state data and IM spacing algorithm performance, and qualitative data were collected through end-of-scenario and end-of-day flight crew surveys. The majority of the IM operations met the performance goals established for spacing accuracy at the Achieve-by Point and the Planned Termination Point, however there were operations that did not meet goals for a variety of reasons. While the positive spacing accuracy results demonstrate the prototype IM avionics can contribute to the overall air traffic goal, critical issues were also identified that need to be addressed to enhance IM performance. The first category was those issues that impacted the conduct and results of the flight test, but are not part of the IM concept or procedures. These included the design of arrival and approach procedures was not ideal to support speed as the primary control mechanism, the ground-side of the Air Traffic Management Technology Demonstration (ATD-1) integrated concept of operations was not part of the flight test, and the high workload to manually enter the information required to conduct an IM operation. The second category was issues associated with the IM spacing algorithm or flight crew procedures. These issues include the high frequency of IM speed changes and reversals (accelerations), a mismatch between the deceleration rate used by the spacing algorithm and the actual aircraft performance, and some spacing error calculations were sensitive to normal operational variations in aircraft airspeed or altitude which triggered additional IM speed changes. Once the issues in these two categories are addressed, the future IM avionics should have considerable promise supporting the goals of improving system throughput and aircraft efficiency.

Baxley, Brian T.↗