Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

High-temperature nanoindentation creep studies on castable and sintered nanostructured low-activation ferritic-martensitic alloys

In this article, we present the creep characteristics of two reduced activation ferritic-martensitic steels of identical starting compositions formed by different fabrication routes: a nanostructured ferritic alloy commonly referred to as a castable nanostructured alloy (CNA) and a sintered nanostructured alloy (SNA) variant. Through a series of nanoindentation experiments spanning a temperature range of 25 °C to 650 °C, with a maximum load of 100 mN, we find creep behaviors in the cast and sintered materials to be remarkably similar. The creep stress exponent (n) for CNA and SNA were found to be in the range of 8–35 and the activation volume was ∼14–42b 3 , underscoring a dominance of dislocation-mediated mechanisms in both alloys. Notably, we observed a decline in the creep stress exponent with increasing temperature, attributable to the heightened influence of thermally activated dislocations. This phenomenon suggests a potential transition in the deformation mechanism towards a thermally activated dislocation climb process, significantly impacting the observed creep behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser repair welding of irradiated alloy 182

Welding repair of irradiated nickel-based alloys, such as Alloy 182, poses a significant challenge due to helium-induced cracking (HeIC) and grain boundary degradation (GBD) in the heat affected zone, driven by helium accumulation at grain boundaries and welding-induced tensile stresses. This study investigates the weldability of irradiated Alloy 182 up to 15 wppm doped boron using both conventional laser welding and the Auxiliary Beam Stress Improved (ABSI) laser welding technique. While HeIC was observed at the weld toe of the entry pass in both methods due to the higher effective heat input associated with the initial pass directly on the base metal, no additional cracking occurred elsewhere, even at elevated helium concentrations. Optical and scanning electron microscopy analysis revealed that the ABSI technique, which introduces additional compressive stresses to counteract solidification-induced tensile stresses, significantly reduced GBD formation, lowering its total count from 1,230 to 339 and decreasing both average and maximum GBD lengths. In conclusion, these results demonstrate that the ABSI technique is a promising approach to mitigate helium-induced damage and improve the weldability of irradiated Alloy 182, offering a viable solution for structural repairs for long-term operation of existing nuclear reactors.

grain boundary degradation↗
DOE OSTI2026

Multiscale study of helium diffusion in Ni-Cr alloys: Short-range trapping versus long-range channeling

Ni-Cr alloys are widely employed as structural materials in fast nuclear reactors but are vulnerable to high-temperature helium (He) embrittlement (HTHE) under fast neutron irradiation. A comprehensive understanding of He diffusion in Ni-Cr alloys, which governs the kinetics of HTHE, is therefore essential for developing resilient materials and preventing failure. In this work, we reveal the underlying mechanisms of He diffusion in pure Ni and Ni-Cr alloys by integrating density functional theory (DFT) with atomic kinetic Monte Carlo (AKMC) simulations. Our findings uncover a non-monotonic dependence of He diffusivity on Cr concentration, contradicting the monotonic trends predicted by DFT-parameterized theories. At low Cr concentrations, He diffusion is dominated by short-range trapping, characterized by multiple trapping sites and a distinct mechanism within the first nearest neighbor of Cr, differing from that in pure Ni. At high Cr concentrations, these local traps become interconnected, forming long-range fast diffusion channels that enhance He mobility. The competition between localized trapping and extended channeling results in a diffusivity that first decreases, then increases with rising Cr content. These atomic-scale insights offer critical guidance for the design of radiation-tolerant Ni-based alloys. Moreover, the combined DFT-AKMC methodology and the concept of random walker diffusion through interconnected energy basins present a broadly applicable framework for studying transport phenomena in disordered systems.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Structural and electrochemical evolution of alloy interfacial layers in anode-free solid-state batteries

“Anode-free” solid-state batteries feature high energy density since there is no anode active material. Although the beneficial effects of interfacial layers at the anode-solid electrolyte interface have been demonstrated, the mechanisms through which they influence lithium plating/stripping are unclear. Here, in this study, we reveal the evolution of 100-nm silver and gold interfacial layers during lithium plating/stripping using electrochemical methods, electron microscopy, X-ray microcomputed tomography, and modeling. The alloy layers improve Coulombic efficiency and resistance to short circuiting, even though the alloys form solute regions or particulates that detach from the current collector during plating. In situ electrochemical impedance spectroscopy shows that the alloys return to the interface and mitigate contact loss at the end of stripping, avoiding a critical vulnerability of anode-free cells. Contact retention is driven by even Li thickness that promotes spatially uniform stripping, as well as local alloy delithiation in response to current concentrations that homogenizes current and diminishes voiding.

25 ENERGY STORAGE↗
DOE OSTI2020

Effect of aging on failure mechanism of Alloy 709 at various temperatures

Alloy 709 is a novel austenitic stainless steel with high temperature creep strength, weldability, and corrosion resistance. These properties make the material suitable for applications in the structure of next-generation nuclear power plants. Enduring high temperatures for an extended period of time in the harsh environments of a nuclear power plant results in thermal aging of the material. Therefore, it is imperative to study the effect of thermal aging on the microstructure and mechanical properties of Alloy 709 before its application in the next generation power plants. In this study, hot-processed (forged + rolled), annealed and quenched ingots of Alloy 709 are aged at 650 °C for 2000 h in air and then tested at various temperatures up to 850 °C in an in-situ heating-loading Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectroscopy (EDS) and Electron Backscatter Diffraction (EBSD). The effect of testing temperature and aging on microstructural evolutions during tensile testing of as-received and aged samples are studied. Furthermore, both as-received and aged samples displayed serrations and drop in ductility at elevated temperatures, due to the effect of dynamic strain aging (DSA). The occurrence of DSA activity was found within temperatures range of 500 °C–750 °C in as-received and 550 °C - 650 °C in aged samples. The aged samples showed less elongation accompanied by shallower dimples on the fractured surface, indicating less ductile failure mechanism compared to as-received samples. Failure mechanism observations on the fracture surface using SEM fractography are correlated to the observations made on the sample surface using in-situ SEM to achieve a complementary set of information to better understand the failure mechanism of this novel alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A study on the creep behavior of alloy 709 using in-situ scanning electron microscopy

In this research, an experimental evaluation of creep properties of Alloy 709 in the temperature range of 750–850 °C was undertaken. Alloy 709 is a novel austenitic stainless steel with 20% Cr and 25% Ni by wt% that was developed for application in structural components of nuclear power plants. Creep rupture tests were conducted in an in-situ heating-loading and Scanning Electron Microscope (SEM) unit equipped with Electron Backscatter Diffraction (EBSD) detector and Energy Dispersive Spectroscopy (EDS). “Real-time” creep damage mechanisms of Alloy 709 at various stresses and temperatures using a flat, un-notched sample with continuously reducing cross-section is studied so that the failure and maximum creep damage occurred at the center of the sample where the in-situ SEM imaging could be focused. Accelerated creep tests at temperatures and stresses above service conditions were performed by employing multiple blocks of constant loads where the loads were increased once the sample attained constant creep rate, indicating a secondary creep regime. This technique ensures multiple data points can be obtained from the same test, saves the time required for an otherwise long-term creep test and usage of SEM. Further, Coincident Site Lattice (CSL) boundary maps were collected as control maps before testing, and the grain boundaries were observed during the creep test to understand the effect of grain boundary character on the creep damage mechanism. Void growth, grain boundary separation, and sliding were found to be the main creep mechanisms whose rate is dependent on stress and temperature. Failure mechanisms studied on the fracture surface using SEM fractography were correlated to the sample surface observations to create complementary information to better understand the underline creep mechanism of Alloy 709.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Cooling dynamics of two titanium alloys during laser powder bed fusion probed with in situ X-ray imaging and diffraction

Metal parts produced by laser powder bed fusion (LPBF) additive manufacturing exhibit characteristic microstructures comparable to those observed in laser welding. The primary cause of this characteristic microstructure is rapid, localized heating and cooling cycles, which result in extreme thermal gradients where material solidification is followed by fast cooling in the solid state. The final microstructure and mechanical performance are also influenced by pore formation caused by melt pool fluid dynamics. Here, we use high speed, in situ X-ray diffraction to probe the kinetics of cooling and solid-solid phase transitions after laser melting in two aerospace titanium alloys: Ti-6Al-4V, an α + β alloy; and Ti-5Al-5V-5Mo-3Cr, a near-β alloy. We complement these diffraction studies with in situ X-ray imaging to probe melt pool dynamics and pore formation. From these two complementary probes, we quantify pore formation during melting and the subsequent microstructural evolution as the material rapidly cools after solidification. These results are critical for understanding defect formation and residual stress development in different titanium alloys under LPBF conditions and can help inform process models to predict final part performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of laser scanning speed on the microstructure, phase transformation and mechanical property of NiTi alloys fabricated by $\mathrm{LPBF}$

This study investigated the effects of laser scanning speed on the microstructure, phase transformation and properties of NiTi alloys fabricated by laser powder bed fusion (LPBF). In this study, the contributions of metallurgical factors under different scanning speeds, such as Ni evaporation, Ni4Ti3 precipitation, dislocations and internal stress, to the transformation temperature and transformation latent heat were clarified through specially designed experiments. Ni evaporation is found to have the most profound effect, followed by precipitation. Increasing scanning speed is found to reduce Ni loss, thus cause less increase in the transformation temperature and transformation heat of the LPBF-NiTi alloys. Increasing scanning speed also increases the microstructure non-uniformity and thus widens the transformation temperature interval. The orientations of residual stress exhibit strong crystallographic stiffness dependence. The LPBF-NiTi alloys with different scanning speeds all exhibited high strains (>13.4%) and excellent shape memory effect. A LPBF-NiTi honeycomb structure exhibited 96% shape recovery rate after a 60% pre-compressive deformation. Besides, there is an optimum scanning speed for minimum porosity and smallest average pore size. However, the pore structure is found to have weak influence on the tensile behaviour of the LPBF-NiTi alloys, possibly due to the high defect tolerance of the martensitic transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The role of Cr concentration and temperature on cavity swelling with co-injected helium in dual-ion irradiated Fe and Fe-Cr alloys

The level of chromium plays an essential role in irradiation tolerance of Fe-Cr ferritic alloys. However, conflicting results have been reported regarding the dependence of cavity swelling under irradiation on Cr level and temperature. Here, we have performed a comprehensive set of simultaneous dual-ion (Ni + He) irradiations to high dose (~30 displacements per atom, dpa) at 400–550 °C on a series of ultra-high purity Fe and Fe-Cr binary alloys (3–14 wt.%Cr). Helium co-implantation rates of 0.1 and 10 appm He/dpa were selected to examine He synergistic effects relevant for fission and fusion reactor conditions, respectively. Cavities were observed in all irradiated samples by transmission electron microscopy. The results show that higher He implantation rate causes a shift in the swelling peak to higher temperatures in both Fe and Fe-Cr alloys. When assuming smaller cavities as biased sinks, the non-monotonic nature of the cavity swelling behavior is related to the ratio of biased to unbiased point defect sink strengths. Cr-enriched precipitates were observed in Fe-14Cr irradiated at 400 °C by atom probe tomography. Our analysis suggests the formation of Cr-enriched precipitates could suppress cavity swelling for Fe-Cr alloys with Cr content above 10 wt%.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multiscale characterization of an additively manufactured property graded Ni-base alloy for molten-salts\supercritical-CO 2 heat exchangers

The sequential optimization of strength and corrosion resistance in conventional alloy design procedures often results in a tradeoff between environmental degradation and optimal mechanical properties. A concurrent optimization of these two material properties is essential to efficiently develop high temperature alloys that can withstand harsh environments increasingly required for carbon–neutral energy technologies. In this work, we demonstrate the feasibility of directed energy deposition (DED) to manufacture a dual-corrosion resistant Ni-based alloy (Hastelloy N and Haynes 282), that meets the high temperature operation requirements of a molten-salts\supercritical-CO 2 (sCO 2 ) heat exchanger. A combination of multiscale characterization techniques and computational thermodynamics was employed to evaluate the cracking susceptibilities during fabrication and predict the microstructural stability of the material. Very good agreement was achieved between the observed and predicted phases and phase fractions of the as-printed material. A careful characterization of the transition zone between the two terminal alloy chemistries revealed potential precipitation strengthening (γ') on the Hastelloy N side while columnar-shaped M 23 C 6 and γ' precipitates that formed at grain boundaries (GBs) of the transition zone likely minimized the local interfacial energies. Both these mechanisms are believed to increase the interfacial stability but their performance at high temperatures requires further investigation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Navigating high-dimensional process-structure–property relations in nanocrystalline Pt-Au alloys with machine learning

For decades, materials scientists have relied on the process-structure–property paradigm to guide investigations into material behaviors. Traditional studies often examine a limited number of process-structure–property variables, striving to elucidate mechanisms governing material response. However, this approach is time consuming and can limit exploration, as well as the discovery of process-structure–property relations in novel materials. In this paper, we combined combinatorial sputter deposition and multi-modal high-throughput materials characterization with feedforward neural networks to establish high-dimensional process-structure–property relations in Pt-Au alloys, yielding nanocrystalline alloys with high hardness and low resistivity relevant to electrical contact switch applications. We mapped three indicators of process conditions (composition and two atomic deposition characteristics) onto four indicators of material structure (X-ray diffraction, film thickness, density, and surface roughness) and two indicators of material properties (hardness and resistivity), resulting in 784 unique combinations evaluated over a 13-dimensional space. The neural networks predicted Pt-Au alloys with 18–24 at.% Au, when deposited at specific conditions, to have a nanoindentation hardness up to 7.2 GPa. This high hardness value, comparable to some steels, represents a 3-fold improvement in hardness over “hard gold”, a commonly used electrical contact alloy, while maintaining requisite electrical conductivity. The neural network models provide an avenue to identify expected process windows capable of maximizing material performance.

Electrical contact materials↗
DOE OSTI2025

Electronic density of states as the descriptor of elastic bond strength, ductility, and local lattice distortion in BCC refractory alloys

Although electronic density of states (DOS) is fundamental to materials properties, its general relationship to mechanical properties of alloys is not well established. In this paper, using density functional theory (DFT) calculations, we show that the electronic occupancy at the Fermi level, N(E f ), obtained from DOS is a key descriptor of alloy strength and ductility. Our comprehensive analysis of numerous body centered cubic (BCC) refractory high entropy alloys (RHEAs) shows an overwhelming correlation that low N(E f ) indicates strong bonds that have high stiffness resulting in high elastic constants. High bond stiffness indicates presence of covalent nature of bonds that are directional in nature resulting in resistance to deformation leading to high bulk (B) and shear (G) moduli. Consequently, N(E f ) provides a direct correlation to the tendency of alloy ductility evidenced in the Pugh ratio (G/B). As stiffer bonds result in lower local lattice distortion (LLD), N(E f ) are LLD are also found to be corelated which opens up a correlation to solid solution strengthening and yield strength. Thus, this work unveils fundamental correlations between N(E f ) and (1) elastic bond strength, (2) ductility, and (3) LLD. These correlations open opportunities for the design of high strength high ductile RHEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deformation behavior of a Co-Cr-Fe-Ni-Mo medium-entropy alloy at extremely low temperatures

In this work, we report the mechanical and microstructural characteristics of a medium-entropy alloy, Co 17.5 Cr 12.5 Fe 55 Ni 10 Mo 5 (atomic percent, at%) at cryogenic temperatures, down to a record low temperature of 0.5 K. The alloy exhibits excellent strength and ductility combined with a high strain-hardening rate in the entire temperature range investigated. Its property profile, including the yield strength, ultimate tensile strength, strain hardening capability, and absorbed mechanical energy, is better than those of most alloys and HEAs used in cryogenics. Within the interval of extremely low temperatures considered (0.5–4.2 K), the alloy exhibits several unusual features, including anomalies of the temperature dependence of the yield strength and tensile ductility, discontinuous plastic deformation (DPF), and a change in the propensity for the deformation-induced martensitic transformation. While the occurrence of these effects in the same temperature interval may be fortuitous, we hypothesize that they are interrelated and provide a tentative explanation of the observed phenomena on this basis.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the exceptionally high ductility of Mg–2Zn-0.3Ca-0.2Ce-0.1Mn alloy

A newly developed Mg–2Zn-0.3Ca-0.2Ce-0.1Mn (in weight %, ZXEM2000) wrought alloy exhibits an exceptionally high tensile ductility (29% ± 1.4% tensile elongation) along the rolling direction at room temperature. In this work, we investigated the fundamental plastic deformation mechanisms that can contribute to the high ductility of ZXEM2000. Scanning electron microscopy and transmission electron microscopy were carried out at selected strain levels to characterize the microstructural evolution. Compared with the deformed microstructures from the hot-rolled pure Mg and Mg–3Al–1Zn alloy at similar conditions, our results revealed that the high ductility of ZXEM2000 could be attributed to four key factors: weaker texture, fine grain size, reduced twinning, and increased cross-slip frequency of < c +a > dislocation. Furthermore, these direct observations offer a key insight into improving ductility of magnesium alloys for future alloy design and development.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Transformation and twinning induced plasticity in metastable Ti-Mo alloys under high strain rate deformation

The development of metastable titanium (Ti) alloys provides an unprecedented opportunity to expand their use in plasticity and damage critical applications like protective structures. However, such applications require knowledge of quasi-static to dynamic mechanical behavior, which is currently lacking. Here we perform in-situ, ultrafast synchrotron x-ray diffraction during high strain rate (Kolsky) pressure bar testing in tension and post-mortem electron microscopy to study TRansformation Induced Plasticity (TRIP) and TWinning Induced Plasticity (TWIP) in metastable Ti-Mo alloys. Two alloys, namely Ti-12Mo and Ti-15Mo (wt.%), were selected for study having different β -phase chemical stabilities. TWIP was observed in both Ti-12Mo and Ti-15Mo by in-situ synchrotron diffraction during high strain rate testing. Post-mortem microstructural characterization also revealed the presence of TRIP in Ti-12Mo. TWIP in Ti-15Mo was found to under-perform in terms of total elongation compared to TRIP/TWIP in Ti-12Mo. Ti-12Mo exhibited an average elongation of 17% compared to only 12% for Ti-15Mo with deformation at 1000 s -1 . In conclusion, TRIP resulted in significantly finer microstructure evolution and alleviated local strain accumulations in Ti-12Mo, suggesting TRIP can be used to tune available strength/ductility combinations in metastable Ti alloys under high strain rate deformation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A high-strength precipitation hardened cobalt-free high-entropy alloy

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. A Co-free (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 88 Ti 4 Al 8 HEA was developed and studied in this work. In contrast to previous Co-free HEAs, this alloy is close to equiatomic in its composition and promises a more pronounced high-entropy effect. Scanning electron microscopy, transmission electron microscopy, atom probe tomography, and synchrotron-based, high-energy X-ray diffraction were used to characterize this alloy and revealed a complex four-phase structure, with an FCC matrix, γ’ precipitates, and a network of B2 and χ phase particles. This structure granted 2151 MPa compressive strength and good thermal stability, but with limited ductility and slow precipitation kinetics. A strengthening analysis of the alloy shows that the B2 and χ provided the most significant strengthening contribution, adding 312 MPa and 788 MPa respectively. Furthermore the strengthening effect from the nanoscale γ' is also considerable, adding 608 MPa in total. This study lays the foundation for the continued development of high-strength Co-free HEAs with improved and satisfactory ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing of a metastable high entropy alloy: Metastability engineered microstructural control via process variable driven elemental segregation

Compositional paradigm shift in high entropy alloys (HEAs) provided new opportunities for microstructural engineering, whereas process control during laser powder bed fusion (LPBF) additive manufacturing (AM) enable fine microstructure tailoring. Metastability engineering in transformation induced plasticity (TRIP) HEAs by addition of minor alloying elements is an attractive strategy for fine microstructural tuning. This study explored in detail the microstructural evolution during LPBF AM of a metastable Fe 40 Mn 20 Co 20 Cr 15 Si 5 (at.%) dual phase HEA (CS-HEA). LPBF processing window for CS-HEA was established based on quantitative analysis and experiments. Based on melt pool overlap lack of fusion pores were observed at lower energy densities (J) of $\textit{J}$ ≤ 31.25 J/mm 3 and key-hole formation by melt pool destabilization in case of $\textit{J}$ ≥ 75 J/mm 3 . The microstructure of CS-HEA consists of metastable FCC-γ and HCP-ε phases; LPBF process parameters governed the final phase fraction in the alloy which has been correlated to metastability alteration of the high temperature γ phase. Final microstructural engineering was devised by LPBF process control which enabled cooling rate manipulation to guide Mn and Si segregation at the cell boundaries, thereby controlling the matrix metastability and final phase fraction. Additionally, high resolution transmission electron microscopy (TEM) revealed disparity in stacking fault morphology in CS-HEA with LPBF process variable alterations associated with local variations in chemical composition and stacking fault energy. Further, the phase evolution with process parameters also affected the nanomechanical behavior of the alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evolution of microstructure and strength of a high entropy alloy undergoing the strain-induced martensitic transformation

In a recent work, we have reported outstanding strength and work hardening exhibited by a metastable high entropy alloy (HEA), Fe 42 Mn 28 Co 10 Cr 15 Si 5 (in at. %), undergoing the strain-induced martensitic transformation from metastable gamma austenite (γ) to stable epsilon martensite (ε). However, the alloy exhibited poor ductility, which was attributed to the presence of the brittle sigma (σ) phase in its microstructure. The present work reports the evolution of microstructure, strength, and ductility of a similar HEA, Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 (in at. %), designed to suppress the formation of σ phase. A cast and then rolled plate of the alloy was processed into four conditions by annealing for 10 and 30 min at 1100 °C and by friction stir processing (FSP) at tool rotation rates of 150 and 400 revolutions per minute (RPM) to facilitate detailed examinations of variable initial grain structures. Neutron diffraction and electron microscopy were employed to characterize the microstructure and texture evolution. The initial materials had variable grain size but nearly 100% γ structure. Diffusionless strain induced γ→ε phase transformation took place under compression with higher rate initially and slower rate at the later stages of deformation, independent on the initial grain size. The transformation facilitated part of plastic strain accommodation and rapid strain hardening owing to a transformation-induced dynamic Hall-Petch-type barrier effect, increase in dislocation density, and texture. Here, the peak strength of nearly 2 GPa was achieved under compression using the structure created by double pass FSP (150 RPM followed by 150 RPM). Remarkably, the tensile elongation exhibited by the alloy was nearly 20% with fracture surfaces featuring a combination of ductile dimples and cleavage.

36 MATERIALS SCIENCE↗