Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “winds”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

High Efficiency 2-Bladed Utility Wind Turbine Enhanced by CoFlow Jet Active Flow Control

The aerodynamic performance and power output of a high efficiency Co-Flow Jet (CFJ) 2-bladed Wind Turbine is studied in this paper. CFJ is a Zero-Net-Mass-Flux (ZNMF) active flow control method that dramatically increases airfoil lift coefficient and suppresses flow separation at a low energy expenditure. The 3D Reynolds Averaged Navier-Stokes (RANS) equations with one-equation Spalart-Allmaras (SA) turbulence model are solved to simulate the 3D flows of the wind turbines. The CFJ-Wind Turbine in this paper is modified from the NREL 3-bladed 3.4 MW reference wind turbine with the same RPM, blade length, distribution of chord, twist, and bending. The CFJ 2-bladed wind turbine utilizes the CFJ-NACA 64 series airfoils at most of the blade span from 31.88\% to the tip. The CFJ injection and suction slots are implemented along the full blade span to enhance the effectiveness and power output. The study shows that the 2-bladed CFJ turbine significantly increases power output compared with the 3-bladed baseline turbine at all wind speeds by 15.8\% at the wind speed of 9.8 m/s and by 25.9\% at 4 m/s respectively. The efficiency enhancement is substantially more at the low wind speed than at high wind speed. This would be very beneficial to increase the annual power output or capacity factor as wind turbines work at the speeds lower than the rated speed for most of the time. The results show that the flow field around the blade surface presents a significant enhanced suction peak near the blade leading edge, which results in a very high tangential force and thus increased wind turbine net power coefficient. Consistent with the previous study for the small NREL Phase VI research wind turbine, this paper demonstrates that CFJ 2-bladed wind turbine is an effective technology to extract more power from the wind at all speeds. This study is just an initial effort to demonstrate the advantage of the CFJ blade with no design optimization. It is believed that there is more potential to further enhance the efficiency improvement.

active flow control↗

Contextualizing Wind Turbine Blade Waste: Comparison to Other Global Waste Streams

Worldwide wind energy generation capacity has grown rapidly over the past several decades, and wind turbines installed at the beginning of this wave of growth are approaching the end of their design lifetimes. As an increasing number of wind power plants reach their end of life, both decommissioning and repowering (i.e., dismantling or refurbishing existing turbines and commissioning new ones) will produce waste material from the retired wind turbines, foundations, and balance of plant. However, the amount and type of waste, particularly for wind blades, is often mischaracterized. Although wind turbine components are largely recyclable, the blades are typically made of fiberglass composites, which can present challenges for material recovery and reuse. Within the USA, the accumulation of wind turbine blades in landfills has raised questions about whether the continued expansion of wind energy is sustainable if it results in substantial future waste. This study compares the mass and volume of potential global wind blade waste to other waste streams. It also discusses the materials used to manufacture wind turbine blades and summarizes current options for material redesign, recycling (recovery and reuse), repurposing, and disposal of used blades. The analysis indicates that, although wind turbine blades could represent 14% of the composite market by 2027, the potential future mass and volume of wind turbine blade waste is relatively small compared to other industries. These findings suggest that although the development of scalable, economically viable, and environmentally sustainable methods for wind turbine manufacturing, repurposing, and recycling is important, it may make sense to take advantage of synergies among multiple industries in recycling composite waste, rather than focusing solely on wind turbine blades. From a global perspective, larger sustainability, recycling, and waste stream reduction impacts can be made in other industries, such as transportation and construction.

17 WIND ENERGY↗

Assessing boundary condition and parametric uncertainty in numerical-weather-prediction-modeled, long-term offshore wind speed through machine learning and analog ensemble

To accurately plan and manage wind power plants, not only does the time-varying wind resource at the site of interest need to be assessed but also the uncertainty connected to this estimate. Numerical weather prediction (NWP) models at the mesoscale represent a valuable way to characterize the wind resource offshore, given the challenges connected with measuring hub-height wind speed. The boundary condition and parametric uncertainty associated with modeled wind speed is often estimated by running a model ensemble. However, creating an NWP ensemble of long-term wind resource data over a large region represents a computational challenge. Here, we propose two approaches to temporally extrapolate wind speed boundary condition and parametric uncertainty using a more convenient setup in which a mesoscale ensemble is run over a short-term period (1 year), and only a single model covers the desired long-term period (20 year). We quantify hub-height wind speed boundary condition and parametric uncertainty from the short-term model ensemble as its normalized across-ensemble standard deviation. Then, we develop and apply a gradient-boosting model and an analog ensemble approach to temporally extrapolate such uncertainty to the full 20-year period, for which only a single model run is available. As a test case, we consider offshore wind resource characterization in the California Outer Continental Shelf. Both of the proposed approaches provide accurate estimates of the long-term wind speed boundary condition and parametric uncertainty across the region (R 2 >0.75), with the gradient-boosting model slightly outperforming the analog ensemble in terms of bias and centered root-mean-square error. At the three offshore wind energy lease areas in the region, we find a long-term median hourly uncertainty between 10 % and 14 % of the mean hub-height wind speed values. Finally, we assess the physical variability in the uncertainty estimates. In general, we find that the wind speed uncertainty increases closer to land. Also, neutral conditions have smaller uncertainty than the stable and unstable cases, and the modeled wind speed in winter has less boundary condition and parametric sensitivity than summer.

17 WIND ENERGY↗

Review of Wind Energy Forecasting Methods for Modeling Ramping Events

Tall onshore wind turbines, with hub heights between 80 m and 100 m, can extract large amounts of energy from the atmosphere since they generally encounter higher wind speeds, but they face challenges given the complexity of boundary layer flows. This complexity of the lowest layers of the atmosphere, where wind turbines reside, has made conventional modeling efforts less than ideal. To meet the nation's goal of increasing wind power into the U.S. electrical grid, the accuracy of wind power forecasts must be improved. In this report, the Lawrence Livermore National Laboratory, in collaboration with the University of Colorado at Boulder, University of California at Berkeley, and Colorado School of Mines, evaluates innovative approaches to forecasting sudden changes in wind speed or 'ramping events' at an onshore, multimegawatt wind farm. The forecast simulations are compared to observations of wind speed and direction from tall meteorological towers and a remote-sensing Sound Detection and Ranging (SODAR) instrument. Ramping events, i.e., sudden increases or decreases in wind speed and hence, power generated by a turbine, are especially problematic for wind farm operators. Sudden changes in wind speed or direction can lead to large power generation differences across a wind farm and are very difficult to predict with current forecasting tools. Here, we quantify the ability of three models, mesoscale WRF, WRF-LES, and PF.WRF, which vary in sophistication and required user expertise, to predict three ramping events at a North American wind farm.

17 WIND ENERGY↗

Aleutian Pribilof Islands Wind Energy Feasibility Study

Under this project, the Aleutian Pribilof Islands Association (APIA) conducted wind feasibility studies for Adak, False Pass, Nikolski, Sand Point and St. George. The DOE funds were also be used to continue APIA's role as project coordinator, to expand the communication network quality between all participants and with other wind interest groups in the state and to provide continued education and training opportunities for regional participants. This DOE project began 09/01/2005. We completed the economic and technical feasibility studies for Adak. These were funded by the Alaska Energy Authority. Both wind and hydro appear to be viable renewable energy options for Adak. In False Pass the wind resource is generally good but the site has high turbulence. This would require special care with turbine selection and operations. False Pass may be more suitable for a tidal project. APIA is funded to complete a False Pass tidal feasibility study in 2012. Nikolski has superb potential for wind power development with Class 7 wind power density, moderate wind shear, bi-directional winds and low turbulence. APIA secured nearly $\$$1M from the United States Department of Agriculture Rural Utilities Service Assistance to Rural Communities with Extremely High Energy Costs to install a 65kW wind turbine. The measured average power density and wind speed at Sand Point measured at 20m (66ft), are 424 W/m2 and 6.7 m/s (14.9 mph) respectively. Two 500kW Vestas turbines were installed and when fully integrated in 2012 are expected to provide a cost effective and clean source of electricity, reduce overall diesel fuel consumption estimated at 130,000 gallons/year and decrease air emissions associated with the consumption of diesel fuel. St. George Island has a Class 7 wind resource, which is superior for wind power development. The current strategy, led by Alaska Energy Authority, is to upgrade the St. George electrical distribution system and power plant. Avian studies in Nikolski and Sand Point have allowed for proper wind turbine siting without killing birds, especially endangered species and bald eagles. APIA continues coordinating and looking for funding opportunities for regional renewable energy projects. An important goal for APIA has been, and will continue to be, to involve community members with renewable energy projects and energy conservation efforts.

17 WIND ENERGY↗

Distributed Wind Resource Assessment: State of the Industry

In support of the U.S. Department of Energy (DOE) Wind and Water Power Technologies Office (WWPTO) goals, researchers from DOE's National Renewable Energy Laboratory (NREL), National Wind Technology Center (NWTC) are investigating the Distributed Wind Resource Assessment (DWRA) process, which includes pre-construction energy estimation as well as turbine site suitability assessment. DWRA can have a direct impact on the Wind Program goals of maximizing stakeholder confidence in turbine performance and safety as well as reducing the levelized cost of energy (LCOE). One of the major components of the LCOE equation is annual energy production. DWRA improvements can maximize the annual energy production, thereby lowering the overall LCOE and improving stakeholder confidence in the distributed wind technology sector by providing more accurate predictions of power production. Over the long term, one of the most significant benefits of a more defined DWRA process could be new turbine designs, tuned to site-specific characteristics that will help the distributed wind industry follow a similar trajectory to the low-wind-speed designs in the utility-scale industry sector. By understanding the wind resource better, the industry could install larger rotors, capture more energy, and as a result, increase deployment while lowering the LCOE. a direct impact on the Wind Program goals of maximizing stakeholder confidence in turbine performance and safety as well as reducing the levelized cost of energy (LCOE). One of the major components of the LCOE equation is annual energy production. DWRA improvements can maximize the annual energy production, thereby lowering the overall LCOE and improving stakeholder confidence in the distributed wind technology sector by providing more accurate predictions of power production. Over the long term, one of the most significant benefits of a more defined DWRA process could be new turbine designs, tuned to site-specific characteristics that will help the distributed wind industry follow a similar trajectory to the low-wind-speed designs in the utility-scale industry sector. By understanding the wind resource better, the industry could install larger rotors, capture more energy, and as a result, increase deployment while lowering the LCOE.

17 WIND ENERGY↗

Wind Turbine/Radar Interference: Offshore Test Options

This paper attempts to describe the options to expand the scope of the current Interagency Field Test & Evaluation (IFT&E) objectives to include wind turbine encroachment on agency missions for offshore wind development in the United States. The options described here build on the recently completed IFT&E test campaigns that took place in 2012 and 2013. Those tests, which looked at the CARSR, ASR-11, ARSR-4, and eight proposed mitigation technologies, found that wind turbines can significantly impact the ability of radars to detect aircraft and meet mission requirements above and near wind farms. One of the more immediate successes of the IF&E Program is that today, several of the infill radar technologies which were tested, took the results of their IF&TE performance to move well beyond Technology Readiness Level 6/7 and some have been deployed and are operating at airports in the United Kingdom (UK). As well, the UK Ministry of Defense (MOD) has deployed the replacement radar which was tested to address specific concerns with especially concerning offshore wind farms. The UK MOD continues to test and hopes to refine these systems so that identified shortfalls in surveillance capability and operations which remain can be addressed. Wind energy has been steadily growing in the U.S. With a current capacity of over 60 GW today and the expectation that this capacity will need to grow to 300 GW to meet the U.S. Department of Energy's (DOE) goal of 20% wind energy in the future, offshore wind farms are gaining more attention. The specific impacts of wind turbine interference on maritime radars have not been determined at this time. However, the DOE did fund a study conducted by the University of Texas at Austin entitled, "Assessment of Offshore Wind Farm Effects on Sea Surface, Subsurface and Airborne Electronic Systems," that focused on identifying the broader Wind-Turbine/Radar Interference: Offshore Test Options SAND2014-17870 effects of electromagnetic interference expected to be caused by offshore wind farms.' A review of that study would be worth the reader's time. And while no comprehensive field studies have been accomplished, it is worth noting that many mitigation solutions that were tested I the IFT&E Program are derived from short-range maritime radar systems. The Wind and Water Power Technologies Office (WWPTO), within the DOE Office of Energy Efficiency and Renewable Energy, supports the development, deployment, and commercialization of wind and water power technologies. This report is funded by the WWPTO.

17 WIND ENERGY↗

Wind Energy Forecasting with the Weather Research and Forecasting Model

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Siemens Energy, Inc. (Siemens) to develop a wind resource forecasting tool. LLNL was to develop an independent high-resolution mesoscale modeling capability forecasting tool that could be implemented in conjunction with existing wind farm control and monitoring software to provide forecasting of wind resources using local observations of winds and temperature. Research with LLNL’s state-of-the-art large-eddy simulation meteorological prediction model, based on the community WRF model and innovative turbulence parameterizations, would improve that model’s applicability to large wind farms offshore and in complex terrain. The modeling capability would include uncertainty quantification. Finally, the application of the modeling tool and existing global climate change predictions would enable the delineation of the likely effects of climate change on wind resources. Siemens was to provide high time resolution hub-height wind speed and other meteorological data streams, including temperature profiles from wind farms, for LLNL to incorporate into the modeling system, to validate and tune this forecasting model for their locations of interest. These data streams would also be used for longer-term studies of correlations of wind resources to climate oscillations to indicate how long-term climate change trends may affect the available wind resource. Siemens would also provide information and observations of turbine wakes for incorporation into the modeling tool. By implementing state-of-the-art turbulence parameterizations into a simulation model and/or ensembles of simulation models, and by integrating real-time hub height wind speed and other meteorological datastreams from wind farms into that model or ensemble of models, LLNL would develop a forecasting tool that could be implemented by Siemens as an add-on to existing wind farm control and monitoring software to provide owners with useful resource forecasting. The desired outcome was that the accuracy level of the output would be sufficient to substantiate power output commitments. The final deliverable for this work would consist of a document outlining the algorithms and software tools that could be integrated into Siemens Wind Park Supervisor.

17 WIND ENERGY↗

Charge States and FIP Bias of the Solar Wind from Coronal Holes, Active Regions, and Quiet Sun

Connecting in situ measured solar-wind plasma properties with typical regions on the Sun can provide an effective constraint and test to various solar wind models. We examine the statistical characteristics of the solar wind with an origin in different types of source regions. We find that the speed distribution of coronal-hole (CH) wind is bimodal with the slow wind peaking at ∼400 km s{sup −1} and the fast at ∼600 km s{sup −1}. An anti-correlation between the solar wind speeds and the O{sup 7+}/O{sup 6+} ion ratio remains valid in all three types of solar wind as well during the three studied solar cycle activity phases, i.e., solar maximum, decline, and minimum. The N{sub Fe}/N{sub O} range and its average values all decrease with the increasing solar wind speed in different types of solar wind. The N{sub Fe}/N{sub O} range (0.06–0.40, first ionization potential (FIP) bias range 1–7) for active region wind is wider than for CH wind (0.06–0.20, FIP bias range 1–3), while the minimum value of N{sub Fe}/N{sub O} (∼ 0.06) does not change with the variation of speed, and it is similar for all source regions. The two-peak distribution of CH wind and the anti-correlation between the speed and O{sup 7+}/O{sup 6+} in all three types of solar wind can be explained qualitatively by both the wave-turbulence-driven and reconnection-loop-opening (RLO) models, whereas the distribution features of N{sub Fe}/N{sub O} in different source regions of solar wind can be explained more reasonably by the RLO models.

79 ASTRONOMY AND ASTROPHYSICS↗

UV Spectropolarimetry with Polstar: Massive Star Binary Colliding Winds

The winds of massive stars are important for their direct impact on the interstellar medium, and for their influence on the final state of a star prior to it exploding as a supernova. However, the dynamics of these winds is understood primarily via their illumination from a single central source. The Doppler shift seen in resonance lines is a useful tool for inferring these dynamics, but the mapping from that Doppler shift to the radial distance from the source is ambiguous. Binary systems can reduce this ambiguity by providing a second light source at a known radius in the wind, seen from orbitally modulated directions. From the nature of the collision between the winds, a massive companion also provides unique additional information about wind momentum fluxes. Since massive stars are strong ultraviolet (UV) sources, and UV resonance line opacity in the wind is strong, UV instruments with a high resolution spectroscopic capability are essential for extracting this dynamical information. Polarimetric capability also helps to further resolve ambiguities in aspects of the wind geometry that are not axisymmetric about the line of sight, because of its unique access to scattering direction information. We review how the proposed MIDEX-scale mission Polstar can use UV spectropolarimetric observations to critically constrain the physics of colliding winds, and hence radiatively-driven winds in general. We propose a sample of 20 binary targets, capitalizing on this unique combination of illumination by companion starlight, and collision with a companion wind, to probe wind attributes over a range in wind strengths. Of particular interest is the hypothesis that the radial distribution of the wind acceleration is altered significantly, when the radiative transfer within the winds becomes optically thick to resonance scattering in multiple overlapping UV lines.

Ultraviolet Astronomy↗

Wind Resource Assessment of Gujarat (India)

India is one of the largest wind energy markets in the world. In 1986 Gujarat was the first Indian state to install a wind power project. In February 2013, the installed wind capacity in Gujarat was 3,093 MW. Due to the uncertainty around existing wind energy assessments in India, this analysis uses the Weather Research and Forecasting (WRF) model to simulate the wind at current hub heights for one year to provide more precise estimates of wind resources in Gujarat. The WRF model allows for accurate simulations of winds near the surface and at heights important for wind energy purposes. While previous resource assessments published wind power density, we focus on average wind speeds, which can be converted to wind power densities by the user with methods of their choice. The wind resource estimates in this study show regions with average annual wind speeds of more than 8 m/s.

17 WIND ENERGY↗

California Time-of-Use (TOU) Transition: Effects on Distributed Wind and Solar Economic Potential

Time-of-use (TOU) retail energy rates price electricity differently by the time of day, thereby communicating to consumers the costs of supplying electricity throughout the day. This study evaluates the impact of Decision D.15.07-001, which mandates a transition to default TOU rates in California, on the economic viability of behind-the-meter distributed wind and solar systems. We assess viability through 'economic potential,' a metric we define as the amount of generation capacity that exceeds a specified rate of return (5.4%) and therefore would be economic to construct; we do not attempt to project deployment or adoption. In addition, we identify cost improvements needed for a robust distributed wind market and the specific counties and sectors with substantial economic potential. Over the scenarios considered, model results indicate realistic pathways to reaching a robust, 1-GW distributed wind market in California though solar economic potential was found to be substantially larger than that of wind. Distributed wind's capacity factor does not appear to be strongly correlated to the periods of peak electricity prices as set by utility's TOU periods. Because of this disassociation and nuances in the billing of tiered electricity, the transition to TOU is projected to moderately decrease distributed wind economic potential and increase that of distributed solar. However, a limitation of this analysis is that it does not factor in the change in rate values as California works toward its goal of 100% renewables. As variable renewable energy penetration increases to meet this goal, our results suggest that wind generation will become increasingly correlated to periods of peak electricity prices. Increased variable renewable penetration, especially of solar, is likely to shift periods of higher electricity demand to later in the evening, and any periodic adjustments in TOU periods to reflect these new periods of demand will positively affect the value of wind generation more than the value of solar generation. High distributed wind capital costs are a significant barrier to large scale adoption; we explore the sensitivity of capital cost reductions on distributed wind economic potential. We find that distributed wind economic potential increases substantially in 2020 for capital costs below 3 dollars/W - particularly for residential- and commercial-scale turbines; capital costs must fall below 2 dollars/W in 2030 to support a significant increase in economic potential, in large part due to the expected continued cost reductions in solar. We identified an upper limit to the state's behind-the-meter distributed wind economic potential at approximately 5 GW. Overall, California exhibits over 1 GW of economic potential for distributed wind by 2030, even with the moderate decrease in potential under TOU. This potential is represented mostly by Southern California, which sees the most notable increase in economic viability as capital expenditure prices decline.

17 WIND ENERGY↗

Wind power forecasting : state-of-the-art 2009.

Many countries and regions are introducing policies aimed at reducing the environmental footprint from the energy sector and increasing the use of renewable energy. In the United States, a number of initiatives have been taken at the state level, from renewable portfolio standards (RPSs) and renewable energy certificates (RECs), to regional greenhouse gas emission control schemes. Within the U.S. Federal government, new energy and environmental policies and goals are also being crafted, and these are likely to increase the use of renewable energy substantially. The European Union is pursuing implementation of its ambitious 20/20/20 targets, which aim (by 2020) to reduce greenhouse gas emissions by 20% (as compared to 1990), increase the amount of renewable energy to 20% of the energy supply, and reduce the overall energy consumption by 20% through energy efficiency. With the current focus on energy and the environment, efficient integration of renewable energy into the electric power system is becoming increasingly important. In a recent report, the U.S. Department of Energy (DOE) describes a model-based scenario, in which wind energy provides 20% of the U.S. electricity demand in 2030. The report discusses a set of technical and economic challenges that have to be overcome for this scenario to unfold. In Europe, several countries already have a high penetration of wind power (i.e., in the range of 7 to 20% of electricity consumption in countries such as Germany, Spain, Portugal, and Denmark). The rapid growth in installed wind power capacity is expected to continue in the United States as well as in Europe. A large-scale introduction of wind power causes a number of challenges for electricity market and power system operators who will have to deal with the variability and uncertainty in wind power generation when making their scheduling and dispatch decisions. Wind power forecasting (WPF) is frequently identified as an important tool to address the variability and uncertainty in wind power and to more efficiently operate power systems with large wind power penetrations. Moreover, in a market environment, the wind power contribution to the generation portofolio becomes important in determining the daily and hourly prices, as variations in the estimated wind power will influence the clearing prices for both energy and operating reserves. With the increasing penetration of wind power, WPF is quickly becoming an important topic for the electric power industry. System operators (SOs), generating companies (GENCOs), and regulators all support efforts to develop better, more reliable and accurate forecasting models. Wind farm owners and operators also benefit from better wind power prediction to support competitive participation in electricity markets against more stable and dispatchable energy sources. In general, WPF can be used for a number of purposes, such as: generation and transmission maintenance planning, determination of operating reserve requirements, unit commitment, economic dispatch, energy storage optimization (e.g., pumped hydro storage), and energy trading. The objective of this report is to review and analyze state-of-the-art WPF models and their application to power systems operations. We first give a detailed description of the methodologies underlying state-of-the-art WPF models. We then look at how WPF can be integrated into power system operations, with specific focus on the unit commitment problem.

17 WIND ENERGY↗

Insensitivity to propagation timing in a preview-enabled wind turbine control experiment

Lidar scanners are capable of taking measurements of a wind field upstream of a wind turbine. The wind turbine controller can use these measurements as a “preview” of future disturbances impacting the turbine. Such preview-enabled (or feedforward) controllers show superior performance to standard wind turbine control configurations based purely on a feedback architecture. To capitalize on the performance improvements that preview wind measurements can provide, feedforward control actions should be timed to coincide with the arrival of the wind field at the wind turbine location. However, the time of propagation of the wind field between the lidar measurement location and the wind turbine is not perfectly known. Moreover, the best time to take feedforward control action may not perfectly coincide with the true arrival time of the wind disturbance. This contribution presents results from an experiment where preview-enabled model predictive control was deployed on a fully-actuated, scaled model wind turbine operating in a wind tunnel testbed. In the study, we investigate the sensitivity of the controller performance to the assumed propagation delay using a range of wind input sequences. We find that the preview-enabled controller outperforms the feedback only case across a wide range of assumed propagation delays, demonstrating a level of robustness to the time alignment of the incoming disturbances.

17 WIND ENERGY↗

Turbulent kinetic energy over large offshore wind farms observed and simulated by the mesoscale model WRF (3.8.1)

Abstract. Wind farms affect local weather and microclimates;hence, parameterizations of their effects have been developed for numerical weather prediction models.While most wind farm parameterizations (WFPs) include drag effects of wind farms, models differ on whether or not an additionalturbulent kinetic energy (TKE) source should be included in theseparameterizations to simulate the impact of wind farms on the boundary layer.Therefore, we use aircraft measurements above large offshore wind farms in stable conditions to evaluateWFP choices. Of the three case studies we examine, we find the simulated ambient backgroundflow to agree with observations of temperature stratification and winds. This agreement allows us toexplore the sensitivity of simulated wind farm effects with respect to modeling choicessuch as whether or not to include a TKE source, horizontal resolution, vertical resolutionand advection of TKE. For a stably stratified marine atmospheric boundary layer (MABL), a TKE source and a horizontal resolutionon the order of 5 km or finer are necessary to represent the impact of offshore wind farms on the MABL.Additionally, TKE advection results in excessively reduced TKE over the wind farms, which in turn causesan underestimation of the wind speed deficit above the wind farm. Furthermore, using fine verticalresolution increases the agreement of the simulated wind speed with satellite observations of surface wind speed.

17 WIND ENERGY↗

Simulating Turbulent Wind Fields for Offshore Turbines in Hurricane-Prone Regions (Poster)

Extreme wind load cases are one of the most important external conditions in the design of offshore wind turbines in hurricane prone regions. Furthermore, in these areas, the increase in load with storm return-period is higher than in extra-tropical regions. However, current standards have limited information on the appropriate models to simulate wind loads from hurricanes. This study investigates turbulent wind models for load analysis of offshore wind turbines subjected to hurricane conditions. Suggested extreme wind models in IEC 61400-3 and API/ABS (a widely-used standard in oil and gas industry) are investigated. The present study further examines the wind turbine response subjected to Hurricane wind loads. Three-dimensional wind simulator, TurbSim, is modified to include the API wind model. Wind fields simulated using IEC and API wind models are used for an offshore wind turbine model established in FAST to calculate turbine loads and response.

17 WIND ENERGY↗

Chapter 6: Wind Energy: Effects on Bats

Utility-scale wind energy facilities require no fuel, consume no water, and produce no greenhouse gas emissions or other pollutants during energy production. Wind power currently supplies approximately 6.4% of the electricity consumed in the United States (U.S.), with continued growth expected in the coming years. Although further expansion of wind power is anticipated to provide environmental and economic benefits, there are increasing concerns about bat fatalities occurring at wind energy facilities across North America. Recent estimates place the number of bat fatalities in the several hundreds of thousands on an annual basis, and that number is projected to rise. As a result, population-level impacts of wind turbine-caused mortality are of increasing concern. For example, modeling efforts for a widespread species, the hoary bat (Lasiurus cinereus), indicate that the population could decline by 90% within 50 years, assuming no growth in installed wind power capacity and no significant implementation of conservation measures. Given increasing demand for wind energy and increasing evidence suggesting that bats are attracted to wind turbines, the need to develop cost-effective and practical impact minimization strategies is a high priority. Current strategies include siting restrictions and operational minimization, both of which limit wind power generation. Potential solutions that do not limit power generation include broadcasting ultrasound from wind turbines or using ultraviolet (UV) light to deter bats from approaching and entering the rotor-swept area where fatalities occur. Another possible solution is the development of turbine-surface materials that reduce the relative attractiveness of wind turbine towers to bats. In this chapter, we provide a succinct summary of known impacts of wind energy on bats and present current and future research priorities. We also describe the challenges and opportunities associated with developing and implementing effective solutions to minimize wind turbine-caused bat fatality.

17 WIND ENERGY↗

A HPC “Cyber Wind Facility” Incorporating Fully-Coupled CFD/CSD for Turbine-Platform-Wake Interactions with the Atmosphere and Ocean

The central aims of the DOE-supported “Cyber Wind Facility” project center on the recognition that wind turbines over land and ocean generate power from atmospheric winds that are inherently turbulent and strongly varying, both spatially over the rotor disk and in temporally as the rotating blades pass through atmospheric eddies embedded within the mean wind. The daytime unstable atmospheric boundary layer (ABL) is particularly variable in space time as solar heating generates buoyancy-driven motions that interact with strong mean shear in the ABL “surface layer,” the lowest 200 - 300 m where wind turbines reside in farms. With the “Cyber Wind Facility” (CWF) program we initiate a research and technology direction in which “cyber data” are generated from “computational experiments” within a “facility” akin to a wind tunnel, but with true space-time atmospheric turbulence that drive utility-scale wind turbines at full-scale Reynolds numbers. With DOE support we generated the key “modules” within a computational framework to create a first generation Cyber Wind Facility (CWF) for single wind turbines in the daytime ABL---both over land where the ABL globally unstable and over water with closer-to-neutral atmospheric conditions but with time response strongly affected by wave-induced forcing of the wind turbine platform (here a buoy configuration). The CWF program has significantly improved the accuracy of actuator line models, evaluated with the Cyber Wind Facility in full blade-boundary-layer-resolved mode. The application of the CWF made in this program showed the existence of important ramp-like response events that likely contribute to bearing fatigue failure on the main shaft and that the advanced ALM method developed here captures the primary nonsteady response characteristics. Long-time analysis uncovered distinctive key dynamics that explain primary mechanisms that underlie potentially deleterious load transients. We also showed that blade bend-twist coupling plays a central role in the elastic responses of the blades to atmospheric turbulence, impacting turbine power.

17 WIND ENERGY↗