Results for “testing data” — Page 65

NASA NTRS1975

Analysis of screeching in a cold flow jet experiment

The screech phenomenon observed in a one-sixtieth scale model space shuttle test of the solid rocket booster exhaust flow noise has been investigated. A critical review is given of the cold flow test data representative of Space Shuttle launch configurations to define those parameters which contribute to screech generation. An acoustic feedback mechanism is found to be responsible for the generation of screech. A simple equation which permits prediction of screech frequency in terms of basic testing parameters such as the jet exhaust Mach number and the separating distance from nozzle exit to the surface of model launch pad is presented and is found in good agreement with the test data. Finally, techniques are recommended to eliminate or reduce the screech.

Wang, M. E.↗

NASA NTRS1984

Free jet feasibility study of a thermal acoustic shield concept for AST/VCE application-dual flow. Comprehensive data report. Volume 1: Test nozzles and acoustic data

Acoustic and diagnostic data that were obtained to determine the influence of selected geometric and aerodynamic flow variables of coannular nozzles with thermal acoustic shields are summarized in this comprehensive data report. A total of 136 static and simulated flight acoustic test points were conducted with 9 scale-model nozzles The tested nozzles included baseline (unshielded), 180 deg shielded, and 360 deg shielded dual flow coannular plug configurations. The baseline configurations include a high radius ratio unsuppressed coannular plug nozzle and a coanuular plug nozzle and a coannular plug nozzle with a 20-chute outer stream suppressor. The tests were conducted at nozzle temperatures and pressure typical of operating conditions of variable cycle engine.

Janardan, B. A.↗

NASA NTRS1978

Considerations in the analysis of flight test maneuvers

This paper discusses the application of a maximum likelihood estimator to dynamic flight-test data. The information presented is based on the experience in the past twelve years at the NASA Dryden Flight Research Center of estimating stability and control derivatives from over 3,000 maneuvers from 32 aircraft. The overall approach to the analysis of dynamic flight-test data is discussed. Detailed requirements for data and instrumentation are discussed and several examples of the types of problems that may be encountered are presented.

Iliff, K. W.↗

NASA NTRS2004

Correlation of Space Shuttle Landing Performance with Post-Flight Cardiovascular Dysfunction

Introduction: Microgravity induces cardiovascular adaptations resulting in orthostatic intolerance on re-exposure to normal gravity. Orthostasis could interfere with performance of complex tasks during the re-entry phase of Shuttle landings. This study correlated measures of Shuttle landing performance with post-flight indicators of orthostatic intolerance. Methods: Relevant Shuttle landing performance parameters routinely recorded at touchdown by NASA included downrange and crossrange distances, airspeed, and vertical speed. Measures of cardiovascular changes were calculated from operational stand tests performed in the immediate post-flight period on mission commanders from STS-41 to STS-66. Stand test data analyzed included maximum standing heart rate, mean increase in maximum heart rate, minimum standing systolic blood pressure, and mean decrease in standing systolic blood pressure. Pearson correlation coefficients were calculated with the null hypothesis that there was no statistically significant linear correlation between stand test results and Shuttle landing performance. A correlation coefficient? 0.5 with a p<0.05 was considered significant. Results: There were no significant linear correlations between landing performance and measures of post-flight cardiovascular dysfunction. Discussion: There was no evidence that post-flight cardiovascular stand test data correlated with Shuttle landing performance. This implies that variations in landing performance were not due to space flight-induced orthostatic intolerance.

McCluskey, R.↗

NASA NTRS2014

Deducing Electronic Unit Internal Response During a Vibration Test Using a Lumped Parameter Modeling Approach

During random vibration testing of electronic boxes there is often a desire to know the dynamic response of certain internal printed wiring boards (PWBs) for the purpose of monitoring the response of sensitive hardware or for post-test forensic analysis in support of anomaly investigation. Due to restrictions on internally mounted accelerometers for most flight hardware there is usually no means to empirically observe the internal dynamics of the unit, so one must resort to crude and highly uncertain approximations. One common practice is to apply Miles Equation, which does not account for the coupled response of the board in the chassis, resulting in significant over- or under-prediction. This paper explores the application of simple multiple-degree-of-freedom lumped parameter modeling to predict the coupled random vibration response of the PWBs in their fundamental modes of vibration. A simple tool using this approach could be used during or following a random vibration test to interpret vibration test data from a single external chassis measurement to deduce internal board dynamics by means of a rapid correlation analysis. Such a tool might also be useful in early design stages as a supplemental analysis to a more detailed finite element analysis to quickly prototype and analyze the dynamics of various design iterations. After developing the theoretical basis, a lumped parameter modeling approach is applied to an electronic unit for which both external and internal test vibration response measurements are available for direct comparison. Reasonable correlation of the results demonstrates the potential viability of such an approach. Further development of the preliminary approach presented in this paper will involve correlation with detailed finite element models and additional relevant test data.

random vibration response↗

NASA NTRS1992

Improve SSME power balance model

Effort was dedicated to development and testing of a formal strategy for reconciling uncertain test data with physically limited computational prediction. Specific weaknesses in the logical structure of the current Power Balance Model (PBM) version are described with emphasis given to the main routing subroutines BAL and DATRED. Selected results from a variational analysis of PBM predictions are compared to Technology Test Bed (TTB) variational study results to assess PBM predictive capability. The motivation for systematic integration of uncertain test data with computational predictions based on limited physical models is provided. The theoretical foundation for the reconciliation strategy developed in this effort is presented, and results of a reconciliation analysis of the Space Shuttle Main Engine (SSME) high pressure fuel side turbopump subsystem are examined.

Karr, Gerald R.↗

NASA NTRS2001

Prediction of Unsteady Aerodynamic Coefficients at High Angles of Attack

The nonlinear indicial response method is used to model the unsteady aerodynamic coefficients in the low speed longitudinal oscillatory wind tunnel test data of the 0.1 scale model of the F-16XL aircraft. Exponential functions are used to approximate the deficiency function in the indicial response. Using one set of oscillatory wind tunnel data and parameter identification method, the unknown parameters in the exponential functions are estimated. The genetic algorithm is used as a least square minimizing algorithm. The assumed model structures and parameter estimates are validated by comparing the predictions with other sets of available oscillatory wind tunnel test data.

Pamadi, Bandu N.↗

NASA NTRS1987

Validation of a real-time engineering simulation of the UH-60A helicopter

A real-time simulation of the UH-60A Black Hawk Helicopter based on the Sikorsky Gen Hel mathematical model is compared with flight test data and Sikorsky's nonreal-time computer program. An overview of the mathematical model is given, including a description of updates and expansion of the model by NASA. Also, real-time programming requirements and techniques are explained. The simulation displays very good agreement with flight test data and excellent with the nonreal-time program on which it is based. The large dedication of effort required to develop the real-time program suggests a need for development of generalized techniques for real-time simulation of high-fidelity physical models of rotorcraft.

Ballin, Mark G.↗

DOE OSTI2024

PyPop: a mature open-source software pipeline for population genomics

Python for Population Genomics (PyPop) is a software package that processes genotype and allele data and performs large-scale population genetic analyses on highly polymorphic multi-locus genotype data. In particular, PyPop tests data conformity to Hardy-Weinberg equilibrium expectations, performs Ewens-Watterson tests for selection, estimates haplotype frequencies, measures linkage disequilibrium, and tests significance. Standardized means of performing these tests is key for contemporary studies of evolutionary biology and population genetics, and these tests are central to genetic studies of disease association as well. Here, we present PyPop 1.0.0, a new major release of the package, which implements new features using the more robust infrastructure of GitHub, and is distributed via the industry-standard Python Package Index. New features include implementation of the asymmetric linkage disequilibrium measures and, of particular interest to the immunogenetics research communities, support for modern nomenclature, including colon-delimited allele names, and improvements to meta-analysis features for aggregating outputs for multiple populations.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS1979

Performance evaluation of Space Shuttle SRB parachutes from air drop and scaled model wind tunnel tests

The aerodynamic performance characteristics have been determined for the Space Shuttle Solid Rocket Booster drogue, main, and pilot parachutes. The performance evaluation on the 20-degree conical ribbon parachutes is based primarily on air drop tests of full scale prototype parachutes. In addition, parametric wind tunnel tests were performed and used in parachute configuration development and preliminary performance assessments. The wind tunnel test data are compared to the drop test results and both sets of data are used to determine the predicted performance of the Solid Rocket Booster flight parachutes. Data from other drop tests of large ribbon parachutes are also compared with the Solid Rocket Booster parachute performance characteristics. Parameters assessed include full open terminal drag coefficients, reefed drag area, opening characteristics, clustering effects, and forebody interference.

Moog, R. D.↗

NASA NTRSDate not supplied

Study of Aircraft Structural Response and Occupant Loading During a Ditching Event Utilizing LS-DYNA Simulation

In this study, the capability of finite element model (FEM) analysis to assess aircraft structural response and occupant injury risk during aircraft water ditching conditions was evaluated. A FEM of the Fokker F28 aircraft, previously validated against full-scale crash test data, was simulated in a realistic water impact environment utilizing recorded conditions from the ditching of US Airways Flight 1549 into the Hudson River. The FEM of the F28 aircraft, was developed from a NASTRAN loads model provided by the vehicle manufacturer, calibrated using component fuselage drop-tests, and validated through test-analysis comparisons from a full-scale crash test of the F28 onto soil. Simulation results are presented in several categories: vehicle kinematics, structural accelerations, damage, occupant responses, and injury risk predictions. Results were consistent with the general outcomes of Flight 1549, indicating that the developed vehicle FEM, validated against land impact test data, may provide an effective tool for evaluating water ditching events.

Jacob Putnam↗

NASA NTRSDate not supplied

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗

NASA NTRSDate not supplied

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗

NASA NTRSDate not supplied

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗

NASA NTRSDate not supplied

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗

NASA NTRS1973

Experimental studies of turbulent aircraft wake

Review of wind tunnel test data obtained for tip vortex studies on a square-tipped rectangular wing. The results include wing surface pressure distributions, three-dimensional velocity components in the wake, and principal vortex characteristics such as peak tangential velocity and core size distributions. The wind tunnel measurements are compared with flight test data. These comparisons show that the magnitudes of circumferential velocities, normalized by flight speed and lift coefficient, as well as the vortex core radius, normalized by wing span, are in close agreement. The data obtained make possible the calculation of turbulence stress distributions and the formulation of models for the prediction of downstream flow fields.

Chigier, N. A.↗

DOE OSTI2022

Horizontal Split Table Conceptual Design for Validation of Nuclear Data used in Advanced Reactors [Slides]

A methodology to create conceptual designs of benchmark critical experiments for advanced reactors nuclear data testing and validation was developed. A first concept was explored, pebble-bed high-temperature gas cooled reactor, based on the HTR-10 reactor. The very high correlation is a proof of concept that the design is similar to the application, and performing such critical experiments would help nuclear data testing and validation. This proof-of-concept was included in the IER-539 CED-1:Preliminary Design of a New Horizontal Split Table report. Other concepts could be explored if needed, such as Molten-salt reactor, Sodium-cooled fast reactor or Heat pipe reactors/Microreactor.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1988

Single-Mode Projection Filters for Modal Parameter Identification for Flexible Structures

Single-mode projection filters are developed for eigensystem parameter identification from both analytical results and test data. Explicit formulations of these projection filters are derived using the orthogonal matrices of the controllability and observability matrices in the general sense. A global minimum optimization algorithm is applied to update the filter parameters by using the interval analysis method. The updated modal parameters represent the characteristics of the test data. For illustration of this new approach, a numerical simulation for the MAST beam structure is shown by using a one-dimensional global optimization algorithm to identify modal frequencies and damping. Another numerical simulation of a ten-mode structure is also presented by using a two-dimensional global optimization algorithm to illustrate the feasibility of the new method. The projection filters are practical for parallel processing implementation.

Huang, Jen-Kuang↗