Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructural evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Effect of heat treatment time on microstructure and electrical conductivity in LATP glass ceramics

Glass-ceramic is prepared by heat treatment of melt quenched 14Li{sub 2}O−9Al{sub 2}O{sub 3}−38TiO{sub 2}−39P{sub 2}O{sub 5} glass in the vicinity of crystallization temperature. Growth of ceramic phase is controlled by tuning heat treatment time at fixed temperature. Ceramic phase was identified to be LiTi{sub 2}(PO{sub 4}){sub 3} from X Ray Diffraction analysis. Microstructural evolution of this phase with hold time was observed under high resolution Scanning Electron Microscope. DC conductivity is observed to increase by 4-5 orders of magnitude in this glass-ceramic compared to parent glass. However, formation of pores and cracks with very large heat treatment time seem to hinder further increase of conductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermomechanical characterization and modeling for TSV structures

Continual scaling of devices and on-chip wiring has brought significant challenges for materials and processes beyond the 32-nm technology node in microelectronics. Recently, three-dimensional (3-D) integration with through-silicon vias (TSVs) has emerged as an effective solution to meet the future technology requirements. Among others, thermo-mechanical reliability is a key concern for the development of TSV structures used in die stacking as 3-D interconnects. This paper presents experimental measurements of the thermal stresses in TSV structures and analyses of interfacial reliability. The micro-Raman measurements were made to characterize the local distribution of the near-surface stresses in Si around TSVs. On the other hand, the precision wafer curvature technique was employed to measure the average stress and deformation in the TSV structures subject to thermal cycling. To understand the elastic and plastic behavior of TSVs, the microstructural evolution of the Cu vias was analyzed using focused ion beam (FIB) and electron backscattering diffraction (EBSD) techniques. Furthermore, the impact of thermal stresses on interfacial reliability of TSV structures was investigated by a shear-lag cohesive zone model that predicts the critical temperatures and critical via diameters.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Linking microstructure to creep behavior in vertically and horizontally built LPBF Haynes 282 compared with wrought material via θ -projection

Laser Powder Bed Fusion (LPBF) has emerged as a promising route for fabricating intricate geometries in high-performance alloys. Haynes 282 (H282) is a strong candidate for applications such as heat exchangers or engines due to its excellent creep strength and thermal stability; however, the long-term creep behavior of LPBF-processed H282 remains poorly understood. In this study, the θ -projection method is used to analyze and extrapolate the creep behavior of vertically built LPBF, horizontally built LPBF, compared to wrought H282 tested at 816 °C. Vertically built LPBF H282 exhibits the lowest minimum creep rate (MCR), while the horizontally built condition shows a higher MCR comparable to that of wrought H282. Despite these differences, both LPBF conditions exhibit significantly shorter rupture life and reduced rupture strain than the wrought material, with the most severe degradation observed in the horizontal builds, consistent with an earlier onset of tertiary creep and accelerated strain-rate evolution. Microstructural characterization reveals that both LPBF and wrought H282 exhibit abundant twin-related boundary character; however, their grain boundary topologies differ markedly. The wrought alloy contains a higher fraction of low-angle grain boundaries and continuous twin lamellae, whereas the LPBF microstructure is characterized by a suppressed low-angle boundary population and fragmented twin-related boundaries embedded within irregular high-angle grain boundary networks. Fractographic analysis further reveals predominantly intergranular cracking in LPBF H282, accompanied by grain-boundary-decorated carbides, Al 2 O 3 inclusions, and high-aspect-ratio pores. These results demonstrate that grain boundary topology, rather than minimum creep rate alone, plays a critical role in governing creep damage accumulation and rupture behavior in LPBF and wrought H282.

Creep↗

Development of microstructure and texture during single and multiple pass friction stir processing of a strain hardenable aluminium alloy

Highlights: • Development of microstructure and texture during single and multiple pass FSP of a strain hardenable aluminium alloy • Strain induced boundary migration (SIBM) is the dominant nucleation mechanism for recrystallization • Weak crystallographic texture development influenced by SIBM with the relative dominance of shear texture components • Stable microstructure and texture development after multiple pass FSP • FSP is a promising method for the secondary processing of strain hardenable aluminium alloys - Abstract: In the present study, microstructure and texture development during single and multiple pass friction stir processing (FSP) of a strain hardenable wrought AlMg alloy (AA5086) was investigated. Subtle differences were observed while comparing with heat treatable alloys in the nucleation mechanism of the recrystallized microstructure observed in the nugget zone. Strain induced boundary migration was the dominant mechanism of microstructure evolution in the alloy, which influenced the crystallographic texture development by weakening it. Micro-texture measurements reveal variations in the crystallographic texture along the thickness of the sample. Recrystallization texture components were observed in the nugget zone indicative of a pronounced static recrystallization in the alloy as compared to the heat treatable alloys. Bulk texture measurements within the nugget zone of the optimally processed sample reveal a relatively dominant C component of shear texture. Average grain size in the nugget zone remained the same and the bulk crystallographic texture components were retained during multiple-pass FSP. The lower strain energies involved and the enhanced recovery processes due to the high temperature materials processing of the alloy during FSP resulted in a stable microstructure and texture. In summary, FSP could be promoted as a competent and suitable secondary processing technique for the bulk production of ultra-fine-grained materials in strain hardenable aluminium alloys.

36 MATERIALS SCIENCE↗

Exploring the tempering behaviour of additively manufactured high-alloy tool steel using synchrotron X-ray and neutron techniques

Post-processing heat treatment provides a critical pathway toward the commercialisation of additively manufactured (AM) S390 high-speed steel, which is a representative high-alloy tool steel employed in precision manufacturing, offering up to 1.5 times longer tool life and over 20% higher cutting speeds compared to conventional grades. In this study, the phase evolution of AM S390 steel during heat treatment, with particular emphasis on carbide precipitation behaviour, was systematically investigated using a combination of synchrotron X-ray and neutron techniques. The metastable M2C carbides were found to dissolve during austenitisation, while the stable primary carbides MC and M6C experienced coarsening with an average size increase of about 60 nm after just 2 min of tempering. Moreover, the austenite lattice parameters reduced from 3.618 to 3.608 Å within the first 10 min of tempering, suggesting carbon depletion in the steel matrix was likely associated with the formation of secondary carbides. This interpretation was substantiated by small-angle scattering results, which revealed the presence of nanoscale precipitates with a volume fraction of 3.1% after 60 min of tempering. These microstructural evolutions collectively accounted for the observed peak hardness of 921 HV. Furthermore, a comparative analysis of synchrotron and neutron small-angle scattering data highlighted the complementary strengths of each technique, offering critical insight into their suitability for characterising nanoscale features in AM high-alloy steels.

Synchrotron X-ray diffraction↗

Atomistic Simulations of Mass and Thermal Transport in Oxide Nuclear Fuels

In this talk we discuss simulations of the mass and thermal transport in oxide nuclear fuels. Redistribution of fission gases such as Xe is closely coupled to nuclear fuel performance. Most fission gases have low solubility in the fuel matrix, specifically the insolubility is most pronounced for large fission gas atoms such as Xe, and as a result there is a significant driving force for segregation of gas atoms to grain boundaries or dislocations and subsequently for nucleation of gas bubbles at these sinks. The first step of the fission gas redistribution is diffusion of individual gas atoms through the fuel matrix to existing sinks, which is governed by the activation energy for bulk diffusion. Fission gas bubbles are then formed by either separate nucleation events or by filling voids that were nucleated at a prior stage; in both cases their formation and latter growth is coupled to vacancy dynamics and thus linked to the production of vacancies via irradiation or thermal events. In order to better understand bulk Xe behavior (diffusion mechanisms) in UO 2±x we first calculate the relevant activation energies using density functional theory (DFT) techniques. By analyzing a combination of Xe solution thermodynamics, migration barriers and the interaction of dissolved Xe atoms with U, we demonstrate that Xe diffusion predominantly occurs via a vacancy-mediated mechanism, though other alternatives may exist in high irradiation fields. Since Xe transport is closely related to diffusion of U vacancies, we have also studied the activation energy for this process. In order to explain the low value of 2.4 eV found for U migration from independent damage experiments (not thermal equilibrium) the presence of vacancy clusters must be included in the analysis. Next a continuum transport model for Xe and U is formulated based on the diffusion mechanisms established from DFT. After combining this model with descriptions of the interaction between Xe and grain boundaries derived from separate atomistic calculations, we simulate Xe redistribution for a few simple microstructures using finite element methods (FEM), as implemented in the MOOSE framework from Idaho National Laboratory. Thermal transport together with the power distribution determines the temperature distribution in the fuel rod and it is thus one of the most influential properties on nuclear fuel performance. The fuel thermal conductivity changes as function of time due to microstructure evolution (e.g. fission gas redistribution) and compositional changes. Using molecular dynamics simulations we have studied the impact of different types of grain boundaries and fission gas bubbles on UO 2 thermal conductivity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Constitutive Model for Hot Deformation of the Cu-Zr-Ce Alloy

Hot compressive deformation behavior of the Cu-Zr-Ce alloy has been investigated according to the hot deformation tests in the 550-900 °C temperature range and 0.001-10 s{sup −1} strain rate range. Based on the true stress–true strain curves, the flow stress behavior of the Cu-Zr-Ce alloy was investigated. Microstructure evolution was observed by optical microscopy. Based on the experimental results, a constitutive equation, which reflects the relationships between the stress, strain, strain rate and temperature, has been established. Material constants n, α, Q and ln A were calculated as functions of strain. The equation predicting the flow stress combined with these materials constants has been proposed. The predicted stress is consistent with experimental stress, indicating that developed constitutive equation can adequately predict the flow stress of the Cu-Zr-Ce alloy. Dynamic recrystallization critical strain was determined using the work hardening rate method. According to the dynamic material model, the processing maps for the Cu-Zr and Cu-Zr-Ce alloy were obtained at 0.4 and 0.5 strain. Based on the processing maps and microstructure observations, the optimal processing parameters for the two alloys were determined, and it was found that the addition of Ce can promote the hot workability of the Cu-Zr alloy.

36 MATERIALS SCIENCE↗

Nanocrystalline ZrN thin film development via atomic layer deposition for U-Mo powder

Zirconium nitride (ZrN) thin film deposited via thermal atomic layer deposition (ALD) has been recently chosen as a candidate technology for application of a diffusion barrier coating on the low enriched uranium alloy powder considered in the NNSA research reactor conversion program. Reported here is the first instance of using ALD for coating actinide materials. For this study, a modified ALD system was constructed to produce one micron thick zirconium nitride (ZrN) coating over spherical particulate of natural uranium-molybdenum (U-Mo) based fuel. The ALD system was designed to have a rotating drum system, with provisions for facilitating sequential exposures of chemicals such as tetrakis dimethyl amido zirconium (TDMAZr) and ammonia (NH 3 ) in order to deposit ZrN. The ALD system was successful in developing a highly conformal ZrN coating covering every individual U-7Mo particle. This article describes the ZrN film synthesis details and reports the produced microstructure and composition of the ALD ZrN as deposited on fuel particulates. The as-fabricated coating was determined to have a nanocrystalline structure in the cubic-ZrN (cF8) phase. It exhibited a dense microstructure with adequate interfacial bonding. TEM-EELS characterization demonstrated that the coating contains a very low amount of oxygen impurity. To understand the potential microstructural evolution for ALD ZrN during reactor operation, an in-situ heavy ion (Kr) irradiation experiment was performed at the IVEM-Tandem facility. A total fluence of 7.5 x 10 15 ions/cm 2 (similar to 10 dpa) was achieved, and apart from minor grain coarsening in the ALD ZrN coating, no significant radiation effects were observed.

36 MATERIALS SCIENCE↗

Dynamic Analysis of Recalescence Process and Interface Growth of Eutectic Fe{sub 82}B{sub 17}Si{sub 1} Alloy

By employing the glass fluxing technique in combination with cyclical superheating, the microstructural evolution of the undercooled Fe{sub 82}B{sub 17}Si{sub 1} alloy in the obtained undercooling range was studied. With increase in undercooling, a transition of cooling curves was detected from one recalescence to two recalescences, followed by one recalescence. The two types of cooling curves were fitted by the break equation and the Johnson–Mehl–Avrami–Kolmogorov model. Based on the cooling curves at different undercoolings, the recalescence rate was calculated by the multi-logistic growth model and the Boettinger–Coriel–Trivedi model. Both the recalescence features and the interface growth kinetics of the eutectic Fe{sub 82}B{sub 17}Si{sub 1} alloy were explored. The fitting results that were obtained using TEM (SAED), SEM and XRD were consistent with the changing rule of microstructures. Finally, the relationship between the microstructure and hardness was also investigated.

36 MATERIALS SCIENCE↗

Synergy between phase transformation and domain switching in two morphotropic phase boundary ferroelectrics

We present that many applications of ferroic materials take advantage of the microstructural redistribution under an external stimulus. Despite extensive studies on the microstructural evolution during both domain switching and phase transformations of high-performance ferroelectrics near morphotropic phase boundaries (MPBs), the synergetic interactions between both leading factors remain unclear. Herein, we have illustrated and discerned the correlative response of phase transformation and domain switching in an archetypical piezoceramic of PbTiO 3 -BiScO 3 using a combination of in situ high-energy synchrotron x-ray diffraction and phase-field simulations. The direct structural evidence and domain development from simulations reveal a significant reversible orientation-dependent emerging phase transformation and enhanced domain switching. Increasingly populated polarization variants aligned with the applied electric field owing to this strong synergistic interaction play an important role in enhancing the piezoelectric performances of MPB ferroelectrics. Lastly, in addition to providing further insight into the microstructures of ferroelectrics, the present results have the potential to guide the design of high-performance materials.

36 MATERIALS SCIENCE↗

Characterization of the Hot Deformation Behavior of a Newly Developed Nickel-Based Superalloy

To clarify the microstructural evolution and hot workability of GH4282 during hot forming processes, the hot deformation behavior of this superalloy was investigated by isothermal compression tests in the temperature interval of 950-1210 °C and the strain rate range of 0.01-10 s{sup −1} with a true strain of 0.7. The results show that the flow stresses decrease with an increase in the deformation temperature and a decrease in the strain rate. The characteristic of dynamic recrystallization is revealed by the flow curves. The variation rule of the flow stress can be well described by the hyperbolic sine type equation, and the thermal deformation activation energy is determined to be 498.118 kJ/mol. The optimum hot working parameters are 1100-1180 °C and 0.01-0.1 s{sup −1}, under which the fine and uniform microstructure can be obtained.

36 MATERIALS SCIENCE↗

Sinter-Bonding of AISI 316L and 17-4 PH Stainless Steels

The sinter-bonding method was used to produce AISI 316L/17-4 PH components by conventional powder metallurgy technology. The production process consisted of following steps: the powder layering, co-pressing and co-sintering processes. The co-sintering process was carried out at different sintering temperatures (1200, 1250 and 1300 °C), and times (60, 90 and 120 min) in hydrogen atmosphere. The effect of co-pressing and co-sintering conditions on the ability to create a permanent connection between AISI 316L and 17-4 PH stainless steels was investigated. The densification, dimensional change and microstructural evolution of sintered AISI 316L/17-4 PH components were studied. The increase in co-pressing pressure as well as using of the longer time and the higher temperature of co-sintering process contributed to increase in AISI 316L/17-4 PH component density. The dilatometric study as well as dimensional changes measurements revealed an appropriate sintering compatibility for AISI 316L and 17-4PH steels when the sintering process was carried out at the temperature of 1200 °C for time ranging from 60 to 120 min and at 1250 °C for shorter sintering times. The sintering at temperature of 1300 °C (regardless of other manufacturing conditions) led to a significant deviation from the cylindrical shape of samples, as a result of difference of shrinkage of AISI 316L and 17-4 PH steels. Microstructural study indicated that AISI 316L and 17-4 PH steels creates a good diffusion joint (without any cracks and warpage) during the high-temperature sintering process. Nickel diffusion takes place from the AISI 316L to 17-4 PH stainless steel, and copper and molybdenum diffuse in opposite direction of nickel diffusion. It is possible to achieve a solid connection between two materials exhibiting difference in chemical composition by using sinter-bonding and conventional powder metallurgy technology.

36 MATERIALS SCIENCE↗

Ex-situ Heat Treatment of TEM Foils in a Custom Titanium Fixture: A Case Study on Ni-based Superalloy

The advancement of microstructural characterization at the nanoscale is critical to understanding the microstructural evolution and performance of engineering materials. Transmission electron microscopy (TEM) plays a vital role in such investigations, particularly when coupled with controlled ex- and in-situ experiments. In this study, we introduce a novel method for ex-situ heat treatment (HT) of TEM foils using a custom-designed fixture, made from pure titanium, and vacuum furnace to inhibit oxidation. This approach ensures precise temperature control and minimal sample contamination during HT, critical for substructural characterization and analysis of metallic materials. The fixture consists of a titanium base with three slits, for three sample foils, and a titanium cap for closure. The entire assembly is placed in a vacuum heat treatment furnace with high vacuum capability to prevent oxidation. To validate the effectiveness of the setup, precipitation behavior and microstructural changes were studied in an IN725 variant heat-treated at 500°C for 1 hour and 282 variant heat-treated at 700°C for 1 hour, as case studies.

electron microscopy↗

Ab initio prediction of FeCr sigma (001)/FCC Fe(111) interfacial energy: Effect of interfacial doping of C, B, and N

Interfacial energy plays a crucial role for high-temperature material systems in determining their microstructure evolution and mechanical properties. Optimizing the interfacial energy through doping can improve the stability, performance, and overall functionality of these materials. Here, the present study delivers theoretical investigation on the sigma FeCr (001)//FCC Fe (111) interfacial energy using ab initio methods, focusing on the implications of interfacial doping with important interstitial elements carbon (C), boron (B), and nitrogen (N). The calculated interfacial energy without doping is 0.183J/m 2 . Upon doping, notable reductions in interfacial energy were observed. Doping with B decreased the interfacial energy to 0.046J/m 2 , with single C doping to 0.126J/m 2 , with two C doping to 0.098J/m 2 , and with a single N doping to 0.071J/m 2 . These findings not only shed light on the atomistic origin for the effect of stabilizing the microstructure of stainless steel at elevated temperatures by interstitial doping, but also present a systematic, thorough ab initio approach to predict interfacial doping properties and guide alloy design to enhance the performance and stability.

FeCr sigma phase↗

Anisotropic domains and antiferrodistortive-transition controlled magnetization in epitaxial manganite films on vicinal SrTiO 3 substrates

We studied the microstructural evolution and magnetism of ferroelastic La 0.9 Sr 0.1 MnO 3 (LSMO) epitaxial thin films grown on SrTiO 3 (001) substrates with different miscut angles. The substrate miscut angle plays a critical role in controlling the in-plane magnetic anisotropy. The microscopic origin of such magnetic anisotropy is attributed to the formation of anisotropic stripe domains along the surface step terraces. The magnetization in the LSMO films was found to be selectively modulated by the antiferrodistortive phase transition of the SrTiO 3 substrate. This phenomenon has been qualitatively explained by a strain modified Stoner–Wohlfarth model. We conclude that the magnetization modulation by the SrTiO 3 phase transition depends on h, the ratio of applied magnetic field to the saturation field. Such modulation is only visible with h < 1. The established domain microstructure–anisotropy–magnetism correlation in manganite films can be applied to a variety of complex oxide thin films on vicinal substrates.

36 MATERIALS SCIENCE↗

Temperature and neutron flux dependence of in-reactor creep for cold-worked Zr-2.5Nb - 2016-0042

Over the past 10 years, internally pressurized capsules made from Zr-2.5Nb tubing have been irradiated in the National Research Universal (NRU) reactor at Chalk River Laboratories at temperatures of 280, 320, and 340 deg. C and dose rates between 3 X10{sup 15} n. m{sup -2}. s{sup -1} and 2 X10{sup 17} n. m{sup -2}. s{sup -1} (E>1 MeV). Periodic gaging has been used to assess the primary and secondary (steady-state) creep behavior. The objective of this detailed and controlled experiment was to determine, for the first time, the creep and microstructure evolution in Zr-2.5Nb tubing over a wide range of irradiation conditions for fast neutron fluxes applicable to a CANDU pressure tube. Similar but 'accelerated' creep experiments have been conducted in the Osiris test reactor at fast neutron fluxes of approximately 1.8 X10{sup 18} n. m{sup -2}. s{sup -1} (E>1 MeV), much greater than the neutron fluxes in the NRU reactor. Although accelerated tests in high-flux reactors such as Osiris provide information on irradiation creep, they do not represent the neutron flux conditions applicable to a power reactor. Tests covering power reactor operating conditions are needed to develop models for in-reactor creep of pressure tubes under the appropriate conditions. The data from the NRU reactor are compared with results from creep capsules with similar starting microstructures but irradiated in the Osiris reactor. The results show that the steady-state diametral and axial creep rates have a complex dependence on stress, temperature, and fast neutron flux. Data from out-reactor creep tests on unirradiated and pre-irradiated creep capsules that show the effect of prior irradiation on creep are also reported. The results are discussed in terms of a combination of creep mechanisms involving dislocation glide and mass transport. (authors)

36 MATERIALS SCIENCE↗

Friction Stir Welding of Dissimilar Al/Al and Al/Non-Al Alloys: A Review

Friction stir welding is a solid-state welding technique that has many advantages over traditional fusion welding, and has been widely adopted in the aerospace and automotive industries. This article reviews research developments in friction stir welding of dissimilar alloys systems, including combinations of aluminum alloys with Mg alloys, Cu, and steel. Microstructural evolution, hardness, tensile and fatigue properties, residual stresses, and corrosion behavior of dissimilar welds will be reported. The effects of processing parameters such as tool rotation and traverse speeds, tool position, material position, and tool geometry on the weld quality are also presented. Discussions on future research directions in friction stir welding will also be provided in the context of existing literature and future high-integrity applications.

36 MATERIALS SCIENCE↗