Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “melt”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Fusion welding of refractory metals and ZrB 2 -SiC-ZrC ceramics

Molybdenum and a molybdenum alloy were fusion welded to ZrB2-based ceramics to determine if the electrical and thermal properties of the metals and ceramics affected their weldability. Commercial ceramic powders were hot pressed, machined into coupons, and preheated to 1600 °C before joining the ceramics to commercial metals using plasma arc welding. Weldability varied as indicated by the range of porosity observed within the fusion zones. Measured thermal and electrical properties appeared to have little to no effect on the weldability of metal-ceramic welds despite the large range of values measured across each property. Differences in melting temperatures between metal and ceramic coupons did affect weldability by changing the weld penetration depth into ceramic coupons. Finally, future studies on metal-ceramic welds are suggested to investigate the effect that work function, melt viscosity, wetting, or other properties have on weldability.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing process parameter determination for a new Fe-C-Cu alloy

As a potential replacement for stainless steel alloys commonly used to print parts with laser powder bed fusion, a new Cu precipitation strengthened ferrous alloy, with composition Fe-0.2C-6Cu (wt%), was recently developed. This material is Co- and Ni-free, printable, has mechanical properties comparable to that of high strength stainless steels (approximately 1300 MPa UTS), and is cost-advantaged relative to existing low-alloy steels for additive manufacturing of parts with complex shapes. To gain traction for broader application, optimal laser powder bed fusion (LPBF) processing conditions to produce nearly defect-free parts without compromising mechanical strength are needed. Here, an optimal processing window based upon laser speeds that achieve minimal porosity was quantified via comparisons of measured melt pool penetration, scan speeds, printed material density and laser beam energy density on a commercial LPBF unit operating at 350 W, 80 μm hatch spacing, and 50 μm layer thickness based upon optimal parameters for 17-4PH. Furthermore, the window is 300 to 500 mm/s to achieve >99.8 % dense Fe-0.2C-6Cu (wt%) specimens. Other defects such as burning, spatter, and lack of fusion were also avoided in this window. The window was validated with in-situ synchrotron X-ray imaging that enabled visualization of the vapor cavity, melting, and solidification during a single laser track scan on a miniature powder bed sample. In addition, in-situ infrared imaging provided temperature fields, cooling rate and solidification range, and confirmed minimal printing defects and spatter within the processing window.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Formation of functionally graded steel by laser powder bed fusion via in-situ carbon doping

Additive Manufacturing (AM) enables functional integration by combining multiple components into a single part to shorten assembly time, reduce weight, and improve performance. Laser Powder Bed Fusion (LPBF) is an important AM method due to excellent spatial resolution, surface finish, and material properties without the need for extensive post-processing. Functional integration could be enhanced by spatial tuning of properties, but LPBF cannot readily vary material composition. Here, this paper addresses a method to add spatial composition control by printing small quantities of dopants via liquid carrier prior to laser fusion. The impact of carbon black suspension added to select regions of a Stainless Steel 316 L powder bed on melt pool dimension, hardness, and porosity is reported. The distribution of the carbon between the doped and plain layers and the resulting spatial variation in hardness is measured. Optical microscopy and composition analysis show that the carbon dispersed uniformly within the layer of deposition and diffused as little as 50 μm in the build direction. Keyhole conditions dramatically increase the inter-layer transport of the dopant. The added carbon increased hardness by >50 %. Porosity increased in doped regions but remained below 1.5 % for the best processing parameters. These results demonstrate that the composition of LPBF parts could be controlled in 3-dimensions using a dopant that is soluble in the melt pool. Additional work will be required to evaluate different dopant materials and optimize processing conditions for full density, but microalloying with soluble dopants appears to be a plausible solution to enhance functional integration with LPBF.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effects of shielding gas and spot reduction on humping suppression in high-speed laser welding

High-speed laser welding is a crucial process to enhance the production rate of fuel cell fabrication. However, exceeding a critical welding speed leads to defect formation such as humps and root concavities, which degrade weld quality and mechanical performance. This study employed shielding gas and spot reduction approaches to suppress these defects. The relationships between individual defect types and their influence on weld strength were systematically examined. Moreover, in situ high-speed synchrotron X-ray imaging was employed to comprehend the mechanisms of humping mitigation by shielding gas through analysis of instantaneous keyhole and melt pool dynamics. The observations reveal that shielding gas mitigates humping by shortening the molten pool through enhanced surface heat convection and by altering surface tension to prevent melt flow collisions. The effects of shielding gas and spot reduction were further incorporated into the dimensionless humping index (π h ) that describes the humping formation tendency. These findings provide mechanistic insights and quantitative guidance for defect control strategies in high-speed laser welding.

08 HYDROGEN↗
DOE OSTI2026

On the formation of swelling and related flaws in laser powder bed fusion

Process monitoring in laser powder bed fusion additive manufacturing can provide insights into stochastic anomalies, melt pool and plume dynamics, and part quality. Swelling, a build anomaly where overbuilt material protrudes through the powder layer after recoating, is readily detectable in post-recoat visible light images of the powder bed. Here, this work identifies several of the underlying mechanisms driving swelling formation by analyzing the influence of processing parameters, laser scan paths, and build plate locations on the presence of swelling detected in situ. Swelling near the edge of the part and swelling in the internal region of the part are shown to correlate with different process conditions. Edge and internal swelling may be driven by different phenomena, with edge swelling predominately occurring on the edge of a part facing the laser module and correlated to clusters of near-surface voids (detected with X-ray computed tomography). A larger spot size, higher laser power, and lower scan velocity also increased the presence of edge swelling. Laser spot size and scan path influenced internal swelling, which occurred preferentially with a larger spot size and in regions with large melt pools, caused by localized heat accumulation due to non-optimal processing parameters or scan path strategies. For coupons processed with a slicer-defined maximum scan vector length, swelling seldom occurred at internal vector-stripe boundaries. These results provide a mechanistic understanding of how swelling can be linked to material flaws, insight into how some instances of swelling can be avoided, and evidence supporting the use of swelling as an in situ indicator for quality assurance and part qualification.

Anomaly↗
DOE OSTI2021

Joining Light Metals with Polymer Composites Through Metal Overcasting

This work investigates a unique technique to join aluminum (Al) and magnesium (Mg) alloys to carbon fiber reinforced polymer (CFRP) composites without the use of adhesives or mechanical fasteners. The joints were made using an overcasting technique where the molten alloys were cast around the polymer composites using high pressure die casting method. Rapid cooling during casting allowed the composite to be embedded inside the cast metal without causing any gross damage to the former even though the molten metal temperature exceeded the melting point of the composite matrix by several 100’s of deg. C. The metal/composite interface was examined using optical microscopy and x-ray imaging and the joint strength was examined through tensile testing. Although evidence of polymer melting was evident in the x-ray images, the embedded section of the composite coupons retained their overall shape and integrity. Preliminary tension tests on Al/CFRP composites showed strength degradation of the CFRP and it failed near the metal/CFRP interface (outside the joint). Strength degradation in the CFRP suggests that the overcasting process needs further optimization to minimize thermal excursion in the CFRP. Nevertheless, the overcasting process shows great promise as a unique joining technique with application in fabricating light-weight structures for automotive and transportation industries.

overcasting, Casting, Mg Castings, Al Casting, Joi↗
DOE OSTI2026

X-ray observation of individual Ti-6Al-4V spherical powder particle impact in an in-situ operando laser directed energy deposition system

Understanding the particle capture mechanism in the laser directed energy deposition additive manufacturing process provides a foundation for improving productivity and reducing material loss. Capturing this phenomenon is challenging due to its highly transient time interval. To analyze the impact behavior of spherical Ti-6Al-4V powder, a custom laser directed energy deposition system was designed to control the deposition of individual particles. Synchrotron X-ray imaging at 24 kHz monitored the impact dynamics of individual powder particles. A multi-physics model based on the Smoothed-Particle Hydrodynamics scheme supported the analysis by providing the temperature and velocity fields of the molten pool. Results revealed that in laser directed energy deposition, surface tension forces dominated the powder–molten pool interaction. Hydrophobic Ti-6Al-4V powder particles had an equilibrium contact angle of 121 degrees with their molten state. Furthermore, Ti-6Al-4V powder particles required a high impact velocity (6 to 12 m/s) to transition from oscillation to submergence behavior. Lastly, oscillating powder particles that impacted near the location of the laser beam exhibited faster melting, highlighting the contribution of the laser beam to the melting mechanism. This work lays the foundation for investigations of powder particle impact in laser directed deposition and supports the validation of numerical models of powder–molten pool interactions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural banding of directed energy deposition-additively manufactured 316L stainless steel

The microstructures of 316 L stainless steel created by rapid solidification are investigated here by comparing the similar microstructures of individual hatches of directed energy deposition additive manufacturing (DED-AM) and those of single, laser surface-melted tracks formed on a solid plate. High recoil pressure, which is exponentially dependent on the laser beam power density, induces convection of the melt pool, which causes formation of microstructural bands in the as-solidified microstructure. The microstructural bands are associated with changes in the chromium concentration and are a significant component of the inhomogeneous microstructure of DED-AM.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of coaxial nozzle wear on catchment efficiency in direct energy deposition built components

Laser based Direct Energy Deposition (DED) systems using metallic powder feedstock are recognized as a promising manufacturing method for their ability to shorten production cycles and create complex part geometries. Components are built by generating a melt pool with a high-power laser beam while material is coaxially injected and left to solidify. An impediment to large scale use of DED lies in poor powder catchment efficiency, the condition in which a portion of injected powder escapes the melt pool resulting in a ratio of decreased printed material mass to mass of supplied feedstock. The wear state of a coaxial nozzle on a DED system within a hybrid manufacturing machine tool has been observed to decrease catchment efficiency over time. Herein this study investigates this effect by adapting flow visualization techniques to an in-situ process monitoring format, the implementation of a Computational Fluid Dynamics (CFD) simulation, and deposition testing. Nozzle geometric defects due to wear are identified and categorized, and the impact of nozzle tip wear, resulting in axial tip reduction, on powder catchment efficiency is proven by multiple calculation methods. A linear correlation between catchment efficiency and powder stream diameter is identified, causing a 15–20% loss in efficiency sustained over incremental nozzle tip reduction up to − 1 mm. These results provide a foundation for further study of wear effects and Zero defect manufacturing solutions for powder fed DED systems.

42 ENGINEERING↗
DOE OSTI2023

Alternative reductants for foam control during vitrification of high-iron High Level Waste (HLW) feeds

Foaming during vitrification of radioactive waste in Joule-Heated Ceramic Melters (JHCM) is exacerbated by trapping of evolving gases, such as CO 2 , NO x and O 2 , beneath a viscous reaction layer. Foaming restricts heat transfer during melting. Sucrose is employed as the baseline additive at the Hanford site in Washington State, USA to reduce foaming. Alternative carbon-based reductant additives were explored in simulated, inactive Hanford high-iron HLW-NG-Fe2 feeds, for both their effect on foaming and to give insight to the behaviour of multivalent species in glass melts under different redox conditions. Graphite, coke (93% C), formic acid and HEDTA additives were compared with sucrose, and a feed with no additive. Graphite and coke additions proved most effective in reducing the maximum foam volume by 51 ± 3% and 54 ± 2%, respectively, compared with 24 ± 5% for sucrose. Lower foaming could result in more efficient vitrification in JHCMs. Reductants also affected redox ratios in the multivalent species present in the feed. The order of reduction, Mn 3+ /Mn 2+ > Cr 6+ /Cr 3+ > Ce 3+ /Ce 4+ > Fe 3+ /Fe 2+ was as predicted on the basis of their redox potentials. There is less reduction overall, particularly in the Fe 3+ → Fe 2+ , than predicted by the calculations, attributed to the oxygenated atmosphere of the experiments.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Quantitative Morphological Characterization of Carbide Inclusions in Uranium Metal

Uranium carbides (UCs) are prevalent inclusions in U metal that form during melting operations from interactions with crucible walls and the casting chamber atmosphere. Although UCs have been studied extensively since the beginning of U metal foundry operations, there are still unknowns regarding the effects of thermomechanical processing on their sizes and morphology. Here, we present the results of a series of controlled cooling experiments with molten uranium to elucidate the effect of cooling rate on inclusion morphology in a-U. Samples were melted using a vacuum induction melter and manually cooled at rates of 2.5, 1.7, 1.1, 0.8, 0.3 (± 1%) K/s from ~1600 K to <700 K in under 1 hour. Subsequent scanning electron microscopy (SEM) was performed on cross-sections of the samples, revealing a complex mixture of UC morphologies that are indicative of diffusion and growth influenced by the thermal processing of the U matrix. Image analysis using the Morphological Analysis of Materials (MAMA) software showed that UC sizes generally grew larger with slower cooling rates, and the two slowest cooling rates noticeably impacted the inclusion circularity and ellipse aspect ratio. These results indicate that UC morphology is sensitive to short cooling rates (<1 hour) and could therefore be controlled in the production of metallic nuclear fuels. Additionally, inclusion speciation and morphologies could potentially provide forensic clues about processing history of unknown metal samples. Understanding the driving forces involved in UC morphology evolution is beneficial for evaluating metal fuels for next generation nuclear reactors and for identifying signatures for nuclear forensics.

Athon, Matthew T.↗
DOE OSTI2022

Effect of sucrose on the oxidation-reduction conditions and retention of rhenium during vitrification of low-activity waste

Technetium speciation and solubility during nuclear waste vitrification are affected by oxygen partial pressure in the melt. Thus, reducing agents such as sucrose, which are routinely added to nuclear waste feeds to repress foaming, can significantly affect the volatilization of Tc and increase its retention in glass. Using Re as a surrogate for Tc, we measured the effect of sucrose addition to two low-activity waste melter feeds on the Re retention, oxygen partial pressure, and iron redox as functions of temperature. As expected, Re retention in glass increased as the sucrose content increased. Furthermore, this is attributed to sucrose reaction with nitrates and nitrites in the feed. Destruction of nitrates and nitrites reduces the salt phase fraction and thus likely promotes Re diffusion into the glass-forming melt. In agreement with available literature, we discuss that a modest increase in the sucrose content (compared to current practice) can significantly improve the Tc retention without reducing Fe 2+ to metal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

A laboratory-scale process for producing dilithium beryllium tetrafluoride (FLiBe) with dissolved uranium tetrafluoride

Flibe Energy, Incorporated (FEI)'s conceptual Lithium Fluoride Thorium Reactor (LFTR) incorporates a chemical processing facility aimed at recovering uranium and other valuable volatile radionuclides while managing harmful radionuclides from the used fuel. The fuel utilized in this reactor is a combination of dilithium beryllium tetrafluoride (Li 2 BeF 4 or FLiBe) and uranium tetrafluoride (UF 4 ), (FLiBe/U). FEI's plan involves extracting the uranium and other valuable volatile fluoride-forming radionuclides using nitrogen trifluoride (NF 3 ). To facilitate laboratory-scale testing of uranium extraction using NF 3 and address the toxicity and physical hazards associated with beryllium and beryllium fluoride (BeF 2 ), we used a two-step process to prepare the simulated fuel salt. The first step entailed thermally decomposing ammonium beryllium tetrafluoride [(NH 4 ) 2 BeF 4 ] (ABeF) through a nominal 3-step process, combined with appropriate amounts of lithium fluoride (LiF) and UF 4 , resulting in the formation of beryllium fluoride (BeF 2 ). In the second step, the mixture was repeatedly melted and frozen at the melting point of FLiBe to prepare the eutectic FLiBe with dissolved UF 4 . Although the concept appears straightforward, the production of FLiBe/U involved various challenges. These challenges included transporting the gaseous decomposition products of ABeF, hydrogen fluoride (HF) and ammonia (NH 3 ), while preventing the formation of ammonium fluoride (NH 4 F). Additionally, it was necessary to control the reaction between the higher-than-anticipated water content in the commercial ABeF with NH 3 , HF, and the condensed NH 4 F, protect UF 4 from forming an unknown black compound, select suitable structural materials to mitigate fluoride corrosion, address the risks associated with beryllium toxicity through equipment design and operational protocols, and monitor process conditions. This article provides an account of the thermal decomposition chemistry observed in the commercial ABeF, describes the FLiBe/U production apparatus, describes the experiences and process refinements developed to prepare FLiBe/U, and presents our characterizations of prepared FLiBe/U.

Ammonium beryllium fluoride thermal decomposition↗
DOE OSTI2025

A critical review of the history of fabricating monolithic U-Mo fuel plates

The fabrication of monolithic uranium-molybdenum alloy fuels, specifically those developed for high-performance research and test reactors, began in the early 2000s. The primary fuel form consists of uranium alloyed with 10-wt% molybdenum in a thin foil coated with zirconium and encapsulated in aluminum-6061 cladding. Over the years, the process has evolved with different types of casting, heat treatments, rolling schedules, and cladding applications. This review examines the history of these fabrication processes and their impact on microstructure and fuel-swelling performance. Even though various fabrication methods were used, we found little correlation between fabrication variation and fuel swelling. This insensitive relationship between fabrication variation and fuel swelling is primarily due to inhomogeneous microstructures that formed during casting and grain refinement that occurred during rolling. We conclude that the fabrication processes we examined produced similar microstructures, indicating that the fuel microstructure is somewhat insensitive to the fabrication parameters evaluated. However, the relatively small amount of historic data, such as those for grain sizes, limited this analysis. More recently fabricated materials, such as those from ongoing irradiation experiment, Mini-Plate-1 and Mini-Plate-2, were also excluded from this analysis and are intended to be reviewed separately. The findings, that fuel microstructure is somewhat insensitive to the fabrication parameters, do not imply that any fabrication method is acceptable, given the uncertainties in data and fuel-swelling observations. For example, only arc melting and vacuum induction melting casting processes were previously explored in the historic fabrication efforts. In conclusion, the findings should not be extrapolated to other casting processes.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Nanostructures evolution assessment and spectroscopic properties modification induced by electronic energy loss in KTaO 3 crystal

Modifications of micro/nanostructure and photoelectric properties under swift ion irradiation (645 MeV Xe 35+ ) of KTaO 3 crystal with varying electronic energy losses (7.2–31.4 keV/nm) and ion velocities (0.18–5.00 MeV/u) have been studied by combining experimental and calculated approaches. The i-TS calculations combined with molecular dynamics simulations are compared with the experimental observations, revealing the inner track fine structures from individual spherical defects to continuous ion tracks with core–shell morphologies, and a quantitative relationship, including the melting (0.42 eV/atom), damage (0.75 eV/atom), and amorphous (1.71 eV/atom) thresholds, is established to successfully predict the inner disorder/amorphous proportions and track damage morphologies. The surface nanostructures of nanohillocks (isolated or partial overlaps) and nanopits (serious overlaps) directly depend on the combined action of the deposited potential and kinetic energies of incident ions, which induce local melting and sublimation in the near-surface region. Owing to the decreased recombination and the increased separation efficiency between electrons and holes, the higher photogenerated charge carrier mobility enhanced the photocurrent effect, further optimizing the photoconductivity performance in Xe 35+ -irradiated KTaO 3 . Therefore, controlled defect engineering using the ion irradiation technique, as an effective strategy, could design tailored nanostructure systems and regulate photoelectric properties, further promoting the development of novel technological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Nondestructive ultrasonic characterization of a triple-weld-bead wire arc additively manufactured ER70S-6 S-curved wall

Understanding build-scale microstructural variation in wire arc additive manufacturing (WAAM) of low-carbon steels is essential for ensuring consistent structure–property relationships throughout large components. Conventional destructive characterization techniques, such as scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), are time-intensive and limited to localized regions, making comprehensive evaluation of large WAAM structures challenging. In this study, a nondestructive ultrasonic approach was employed to characterize a 252 mm tall ER70S-6 S-curved WAAM wall produced using a triple-bead deposition strategy. Optical and SEM analysis revealed a repeating dual-region microstructure consisting of uniform polygonal ferrite at melt pool centers and heterogeneous ferrite with coarse and fine grains near melt pool boundaries, attributed to cyclic thermal conditions. Longitudinal ultrasonic backscatter imaging was used to evaluate the continuity of this periodicity along the full build height. The ultrasonic response exhibited a consistent repeating pattern that correlated with the observed layer-wise microstructural variation. X-ray computed tomography confirmed the absence of detectable porosity, indicating that ultrasonic contrast is primarily governed by grain morphology. Overall, the results indicate that longitudinal backscatter ultrasound is a promising nondestructive characterization technique for validating microstructural variations along the s-curved WAAM wall, with significant potential for microstructure optimization and process control.

36 MATERIALS SCIENCE↗