SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Commercially available plastic film materials that remain flexible at cryogenic temperatures and resist failures caused by folds and wrinkles created during expulsion were investigated for use in expulsion bladders for liquefied gases. Compatible adhesive systems, fabrication techniques, and results of impact and dynamic loading tests are summarized.
A 50 megawatt hypersonic arc wind tunnel was developed, with up to 5.0-feet-diameter test sections, for thermostructural tests of lifting entry vehicles.
The study to develop inlet and exit treatments which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel is reported. The investigation was conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios between zero and one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three directions generally less than 1/2 knot (0.26 m/sec) for wind velocities of 15 knots (7.7 m/sec) or less. The loss in total pressure due to the inlet treatment was low: about 0.03 of the test-section dynamic pressure.
Discussion of the deployment of multiple hinged booms from the IMP-I satellite, which is a good example of the use of the combined analysis and testing approach for preflight system reliability evaluation. The procedures used for test and evaluation of the booms are described, and problems encountered and results achieved are considered. Analytical methods, using a digital computer program, and functional test operation with the best possible environmental simulation, were both applied to the problem and comparisons between analytical and test results were made to evaluate their validity and to reveal the effects of errors and imperfections. There is a synergistic advantage in the combined approach in that mutual comparison gives better evaluation of both analysis and test results than independent study of either. An appendix presents some results of a later and as yet incomplete test program involving the IMP-H satellite.
Human-engineering approach was used to design integral seat which provides all the safety, comfort, and protective features that can possibly be afforded airline passengers. Results of dynamic impact testing indicated that seat can withstand and attenuate gravity loads of 21-g horizontal and 45-g vertical; by design, seat will withstand lateral g's as well.
The establishment of norms for interpreting long term dynamic electrocardiograms is attempted by correlating a completely disease symptom and cardiac risk factor free sample with a non-pure sample in the direction of normality on various variables. Out of a population of 362 subjects exposed to dynamic electrocardiogram testing, a discrimination between normals and abnormals in terms of traditional risk factors was observed. The two groups differed significantly on the following variables: cholesterol, smoking, systolic blood pressure, white blood count, fasting blood sugar, uric acid, resting EKG, year of birth, and coronary insufficiency.
The refinement of inlet and exit treatments were studied which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel. The investigation was conducted in the Ames Research Center 40- by 80-foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios from zero to somewhat greater than one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three component directions generally less. The loss in total pressure due to the inlet treatment was low: about 0.035 of the test-section dynamic pressure for the no-wind case.
This paper presents the design development of a truss-type structure which utilizes graphite/epoxy as the primary material system. A review is given of an on-going NASA sponsored program to develop a structural assembly which is required to have a very high degree of dimensional stability. Methods of material characterization and selection are given along with property data such as strength, stiffness, outgassing and thermal expansion. Finite element (NASTRAN) analysis will be discussed and deflection plots of the lowest mode frequencies will be presented. Proposed full scale tests: static, dynamic, and thermal/vacuum will be described.
Study suggests ways of reducing chatte, increasing productivity, and reducing tool wear. Report also describes static and dynamic cutting tests and tool materials and finishes.
The JT8D-109 engine has a sea level static, standard day bare engine takeoff thrust of 73,840 N. At sea level standard day conditions the additional thrust of the JT8D-109 results in 2,040 kg additional takeoff gross weight capability for a given field length. Range loss of the DC-9 Refan airplane for long range cruise was determined. The Refan airplane demonstrated stall, static longitudinal stability, longitudinal control, longitudinal trim, minimum control speeds, and directional control characteristics similar to the DC-9-30 production airplane and complied with airworthiness requirements. Cruise, climb, and thrust reverser performance were evaluated. Structural and dynamic ground test, flight test and analytical results substantiate Refan Program requirements that the nacelle, thrust reverser hardware, and the airplane structural modifications are flightworthy and certifiable and that the airplane meets flutter speed margins. Estimated unit cost of a DC-9 Refan retrofit program is 1.338 million in mid-1975 dollars with about an equal split in cost between airframe and engine.
A time-controlled navigation system applicable to the descent phase of flight for airline transport aircraft was developed and simulated. The design incorporates the linear discrete-time sampled-data version of the linearized continuous-time system describing the aircraft's aerodynamics. Using optimal linear quadratic control techniques, an optimal deterministic control regulator which is implementable on an airborne computer is designed. The navigation controller assists the pilot in complying with assigned times of arrival along a four-dimensional flight path in the presence of wind disturbances. The strategic air traffic control concept is also described, followed by the design of a strategic control descent path. A strategy for determining possible times of arrival at specified waypoints along the descent path and for generating the corresponding route-time profiles that are within the performance capabilities of the aircraft is presented. Using a mathematical model of the Boeing 707-320B aircraft along with a Boeing 707 cockpit simulator interfaced with an Adage AGT-30 digital computer, a real-time simulation of the complete aircraft aerodynamics was achieved. The strategic four-dimensional navigation controller for longitudinal dynamics was tested on the nonlinear aircraft model in the presence of 15, 30, and 45 knot head-winds. The results indicate that the controller preserved the desired accuracy and precision of a time-controlled aircraft navigation system.
Techniques for the measurement of the dynamic stability of linear systems are discussed. Particular attention is given to an analysis of the errors in the procedures, and to methods for calculating the system damping from the data. The techniques discussed include: transient decay, moving block analysis, spectral analysis, random decrement signatures, transfer function analysis, and parameter identification methods. The special problems of rotorcraft dynamic stability testing are discussed.
Efforts to improve the impact resistance of B/Al are reviewed and analyzed. Tensile and dynamic modulus tests, thin sheet Charpy and Izod impact tests, and standard full size Charpy impact tests were conducted on 0.20 mm (8 mil) diameter-B/1100 Al matrix composites. Angleplies ranged from unidirectional to + or - 30 deg. The best compromise between reduced longitudinal properties and increased transverse properties was obtained with + or - 15 deg angleply. The pendulum impact strengths of improved B/Al were higher than that of notched titanium and appear to be enough to warrant consideration of B/Cl for application to fan blades in aircraft gas turbine engines.
Applications of the finite element method to the two dimensional elastodynamics of cracked structures are presented. Stress intensity factors are computed for two problems involving stationary cracks. The first serves as a vehicle for discussing lumped-mass and consistent-mass characterizations of inertia. In the second problem, the behavior of a photoelastic dynamic tear test specimen is determined for the time prior to crack propagation. Some results of a finite element simulation of rapid crack propagation in an infinite body are discussed.
The Space Telescope is a 2.4 m class aperture optical telescope having near-diffraction-limited performance. It will be placed into earth orbit by 1980 via the Space Shuttle. The problem considered is how to achieve negligible degradation of the astronomy imaging capability (to 0.005 arc second) due to smearing by pointing motions during observations. Initially, pointing instability sources were identified and a linear stability was used to assess the magnitude of elastic body modes and to design control system compensation regions necessary for subsequent adaptive control. A spectral identification technique for this adaptive attitude control and pointing has been investigated that will alleviate requirements for comprehensive dynamic ground testing. Typical all-digital simulation results describing motions of the telescope line of sight are presented.
Static and dynamic stability tests were made of a finned projectile configuration with the aft-mounted fins arranged in a cruciform pattern. The tests were made at free stream Mach numbers of 0.7, 0.9, 1.1, and 1.2 in the Langley 8-foot transonic pressure tunnel. Some of the parameters measured during the tests were lift, drag, pitching moment, pitch damping, and roll damping. Configurations tested included the body with undeflected fins, the body with various fin deflections for control, and the body with fins removed. Theoretical estimates of the stability derivatives were made for the fins on configuration.
The current status of aerial applications technology research at the Langley's Vortex Research Facility and Full-Scale Wind Tunnel is reviewed. Efforts have been directed mainly toward developing and validating the required experimental and theoretical research tools. A capability to simulate aerial dispersal of materials from agricultural airplanes with small-scale airplane models, numerical methods, and dynamically scaled test particles was demonstrated. Tests on wake modification concepts have proved the feasibility of tailoring wake properties aerodynamically to produce favorable changes in deposition and to provide drift control. An aerodynamic evaluation of the Thrush Commander 800 agricultural airplane with various dispersal systems installed is described. A number of modifications intended to provide system improvement to both airplane and dispersal system are examined, and a technique for documenting near-field spray characteristics is evaluated.
The paper discusses the Navy's XFV-12A tethered hover testing capabilities utilizing NASA's Impact Dynamic Research Facility (IDRF) at Langley. The facility allows for both static and dynamic tethered hover test operations to be undertaken with safety. The installation which consists of the 'Z' system (tether), restraint system, static tiedowns and the control room and console, is presented in detail. Among the capabilities demonstrated were the ability to recover the aircraft anytime during a test, to rapidly and safely define control limits, and to provide a realistic environment for pilot training and proficiency in VTOL flight.