Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “design space approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Liquid Oxygen/Liquid Methane Integrated Propulsion System Test Bed

In support of NASA?s Propulsion and Cryogenic Advanced Development (PCAD) project, a liquid oxygen (LO2)/liquid methane (LCH4) Integrated Propulsion System Test Bed (IPSTB) was designed and advanced to the Critical Design Review (CDR) stage at the Johnson Space Center. The IPSTB?s primary objectives are to study LO2/LCH4 propulsion system steady state and transient performance, operational characteristics and to validate fluid and thermal models of a LO2/LCH4 propulsion system for use in future flight design work. Two phase thermal and dynamic fluid flow models of the IPSTB were built to predict the system performance characteristics under a variety of operating modes and to aid in the overall system design work. While at ambient temperature and simulated altitude conditions at the White Sands Test Facility, the IPSTB and its approximately 600 channels of system instrumentation would be operated to perform a variety of integrated main engine and reaction control engine hot fire tests. The pressure, temperature, and flow rate data collected during this testing would then be used to validate the analytical models of the IPSTB?s thermal and dynamic fluid flow performance. An overview of the IPSTB design and analytical model development will be presented.

Flynn, Howard↗

Space Transportation Infrastructure Supported By Propellant Depots

A space transportation infrastructure is described that utilizes propellant depot servicing platforms to support all foreseeable missions in the Earth-Moon vicinity and deep space out to Mars. The infrastructure utilizes current expendable launch vehicle (ELV) systems such as the Delta IV Heavy, Atlas V, and Falcon 9, for all crew, cargo, and propellant launches to orbit. Propellant launches are made to Low-Earth-Orbit (LEO) Depot and an Earth-Moon Lagrange Point 1 (L1) Depot to support a new reusable in-space transportation vehicles. The LEO Depot supports missions to Geosynchronous Earth Orbit (GEO) for satellite servicing and to L1 for L1 Depot missions. The L1 Depot supports Lunar, Earth-Sun L2 (ESL2), Asteroid and Mars Missions. New vehicle design concepts are presented that can be launched on current 5 meter diameter ELV systems. These new reusable vehicle concepts include a Crew Transfer Vehicle (CTV) for crew transportation between the LEO Depot, L1 Depot and missions beyond L1; a new reusable lunar lander for crew transportation between the L1 Depot and the lunar surface; and Mars orbital Depot are based on International Space Station (ISS) heritage hardware. Data provided includes the number of launches required for each mission utilizing current ELV systems (Delta IV Heavy or equivalent) and the approximate vehicle masses and propellant requirements. Also included is a discussion on affordability with ideas on technologies that could reduce the number of launches required and thoughts on how this infrastructure include competitive bidding for ELV flights and propellant services, developments of new reusable in-space vehicles and development of a multiuse infrastructure that can support many government and commercial missions simultaneously.

Smitherman, David↗

Passive vs. Parachute System Architecture for Robotic Sample Return Vehicles

The Multi-Mission Earth Entry Vehicle (MMEEV) is a flexible vehicle concept based on the Mars Sample Return (MSR) EEV design which can be used in the preliminary sample return mission study phase to parametrically investigate any trade space of interest to determine the best entry vehicle design approach for that particular mission concept. In addition to the trade space dimensions often considered (e.g. entry conditions, payload size and mass, vehicle size, etc.), the MMEEV trade space considers whether it might be more beneficial for the vehicle to utilize a parachute system during descent/landing or to be fully passive (i.e. not use a parachute). In order to evaluate this trade space dimension, a simplified parachute system model has been developed based on inputs such as vehicle size/mass, payload size/mass and landing requirements. This model works in conjunction with analytical approximations of a mission trade space dataset provided by the MMEEV System Analysis for Planetary EDL (M-SAPE) tool to help quantify the differences between an active (with parachute) and a passive (no parachute) vehicle concept.

Maddock, Robert W.↗

Challenges with Electrical, Electronics, and Electromechanical Parts for James Webb Space Telescope

James Webb Space Telescope (JWST) is the space-based observatory that will extend the knowledge gained by the Hubble Space Telescope (HST). Hubble focuses on optical and ultraviolet wavelengths while JWST focuses on the infrared portion of the electromagnetic spectrum, to see the earliest stars and galaxies that formed in the Universe and to look deep into nearby dust clouds to study the formation of stars and planets. JWST, which commenced creation in 1996, is scheduled to launch in 2018. It includes a suite of four instruments, the spacecraft bus, optical telescope element, Integrated Science Instrument Module (ISIM, the platform to hold the instruments), and a sunshield. The mass of JWST is approximately 6200 kg, including observatory, on-orbit consumables and launch vehicle adaptor. Many challenges were overcome while providing the electrical and electronic components for the Goddard Space Flight Center hardware builds. Other difficulties encountered included developing components to work at cryogenic temperatures, failures of electronic components during development and flight builds, Integration and Test electronic parts problems, and managing technical issues with international partners. This paper will present the context of JWST from a EEE (electrical, electronic, and electromechanical) perspective with examples of challenges and lessons learned throughout the design, development, and fabrication of JWST in cooperation with our associated partners including the Canadian Space Agency (CSA), the European Space Agency (ESA), Lockheed Martin and their respective associated partners. Technical challenges and lessons learned will be discussed.

EEE Parts↗

Analysis of Electrical Characteristics of Thin Film Photovoltaic Cells

Solar energy is the most abundant form of energy in many terrestrial and extraterrestrial environments. Often in extraterrestrial environments sunlight is the only readily available form of energy. Thus the ability to efficiently harness solar energy is one of the ultimate goals in the design of space power systems. The essential component that converts solar energy into electrical energy in a solar energy based power system is the photovoltaic cell. Traditionally, photovoltaic cells are based on a single crystal silicon absorber. While silicon is a well understood technology and yields high efficiency, there are inherent disadvantages to using single crystal materials. The requirements of weight, large planar surfaces, and high manufacturing costs make large silicon cells prohibitively expensive for use in certain applications. Because of silicon s disadvantages, there is considerable ongoing research into alternative photovoltaic technologies. In particular, thin film photovoltaic technologies exhibit a promising future in space power systems. While they are less mature than silicon, the better radiation hardness, reduced weight, ease of manufacturing, low material cost, and the ability to use virtually any exposed surface as a substrate makes thin film technologies very attractive for space applications. The research group lead by Dr. Hepp has spent several years researching copper indium disulfide as an absorber material for use in thin film photovoltaic cells. While the group has succeeded in developing a single source precursor for CuInS2 as well as a unique method of aerosol assisted chemical vapor deposition, the resulting cells have not achieved adequate efficiencies. While efficiencies of 11 % have been demonstrated with CuInS2 based cells, the cells produced by this group have shown efficiencies of approximately 1 %. Thus, current research efforts are turning towards the analysis of the individual layers of these cells, as well as the junctions between them, to determine the cause of the poor yields. As a student of electrical engineering with some material science background, my role in this research is to develop techniques for analyzing the electrical characteristics of the CuInS2 cells. My first task was to design a shadow mask to be used to place molybdenum contacts under a layer of CuInS;! in order to analyze the contact resistance between the materials. In addition, I have also analyzed evaporated aluminum top contacts and have tested various methods of increasing their thicknesses in order to decrease series resistance. More recently I have worked with other members of the research group in reviving a vertical cold-wall reactor for experimentation with CuInS2 quantum dots. As part of that project, I have improved the design for a variable frequency and pulse width square wave generator to be used in driving the precursor injection process. My task throughout the remainder of my tenure is to continue to analyze and develop tools for the analysis of electrical properties of the CuInS2 cells with the ultimate goal of discovering ways to improve the efficiency of our photovoltaic cells. Traditionally, photovoltaic cells are based on a single crystal silicon absorber. While The research group lead by Dr. Hepp has spent several years researching copper indium

Kasick, Michael P.↗

On-Orbit Operation of the Adiabatic Demagnetization Refrigerator on the Astro-H/Hitomi Soft X-ray Spectrometer Instrument

The Soft X-ray Spectrometer instrument on the Astro-H observatory contains a 6x6 array of x-ray microcalorimeters, which is cooled to 50 mK by an adiabatic demagnetization refrigerator (ADR). The ADR consists of three stages in order to provide stable detector cooling using either a 1.2 K superfluid helium bath or a 4.5 K Joule-Thomson (JT) cryocooler as its heat sink. When liquid helium is present, two of the ADRs stages are used to single-shot cool the detectors while rejecting heat to the helium. After the helium is depleted, all three stages are used to cool both the helium tank (to about 1.5 K) and the detectors (to 50 mK) using the JT cryocooler as its heat sink. The Astro-H observatory, renamed Hitomi after its successful launch in February 2016, carried approximately 36 liters of helium into orbit. On day 5, the helium had cooled sufficiently (1.4 K) to allow operation of the ADR. This paper describes the design, operation and on-orbit performance of the ADR.

sub-kelvin refrigeration↗

Discrete-time stability of continuous-time controller designs for large space structures

In most of the stable control designs for flexible structures, continuous time is assumed. However, in view of the implementation of the controllers by on-line digital computers, the discrete-time stability of such controllers is an important consideration. In the case of direct-velocity feedback (DVFB), involving negative feedback from collocated force actuators and velocity sensors, it is not immediately apparent how much delay due to digital implementation of DVFB can be tolerated without loss of stability. The present investigation is concerned with such questions. A study is conducted of the discrete-time stability of DVFB, taking into account an employment of Euler's method of approximation of the time derivative. The obtained result gives an indication of the acceptable time-step size for stable digital implementation of DVFB. A result derived in connection with the consideration of the discrete-time stability of stable continuous-time systems provides a general condition under which digital implementation of such a system will remain stable.

Balas, M. J.↗

Evacuated load-bearing high performance insulation study

A light weight, vacuum jacketed, load bearing cryogenic insulation system was developed and tested on a 1.17-m (46-in.) spherical test tank. The vacuum jacket consists of 0.08 mm (0.003 in.) thick 321 stainless steel formed into a wedge design that allows elastic jacket movements as the tank shrinks (cools) or expands (warms up or is pressurized). Hollow glass spheres, approximately 80 micrometers in diameter with a bulk density of 0.069 g/cc (4.3 lb cubic foot), provide the insulating qualities and one atmosphere load bearing capability required. The design, fabrication, and test effort developed the manufacturing methods and engineering data needed to scale the system to other tank sizes, shapes, and applications. The program demonstrated that thin wall jackets can be formed and welded to maintain the required vacuum level of .013 Pa yet flex elastically for multiple reuses. No significant shifting or breakage of the microspheres occurred after 13 simulated Space Tug flight cycles on the test tank and a hundred 1 atmosphere load cycles in a flat plate calorimeter. The test data were then scaled to the Space Tug LO2 and LH2 tanks, and weight, thermal performance, payload performance, and costs were compared with a helium purged multilayer insulation system.

Parmley, R. T.↗

Modeling ESA's TT/C systems

After a brief introduction on the need for simulation packages for the analysis and design of satellite communications systems, the software tool developed for the European Space Agency (ESA), its main objectives and the design choices made during the development are presented. A very concise description of the available communications and measurement block follows. The ESA standard Telemetry, Tracking and Command (TT&C) system simulator is then introduced along with a description of the ESA standard modulation and coding schemes. As an example, the simulation of the ranging system which is a non-standard communications block, is described in details. Several examples of TT&C simulations outputs are given and compared with measurement results or theoretical approximations, when available. Finally, future developments like the support of advanced modulation schemes and the dynamic satellite link simulation are presented.

Vassallo, Enrico↗

Design Considerations for Space Transfer Vehicles Using Solar Thermal Propulsion

The economical deployment of satellites to high energy earth orbits is crucial to the ultimate success of this nations commerical space ventures and is highly desirable for deep space planetary missions requiring earth escape trajectories. Upper stage space transfer vehicles needed to accomplish this task should ideally be simple, robust, and highly efficient. In this regard, solar thermal propulsion is particularly well suited to those missions where high thrust is not a requirement. The Marshall Space Flight Center is , therefore, currently engaged in defining a transfer vehicle employing solar thermal propulsion capable of transferring a 1000 lb. payload from low Earth orbit (LEO) to a geostationary Earth orbit (GEO) using a Lockheed launch vehicle (LLV3) with three Castors and a large shroud. The current design uses liquid hydrogen as the propellant and employs two inflatable 16 x 24 feet eliptical off-axis parabolic solar collectors to focus sunlight onto a tungsten/rhenium windowless black body type absorber. The concentration factor on this design is projected to be approximately 1800:1 for the primary collector and 2.42:1 for the secondary collector for an overall concentration factor of nearly 4400:1. The engine, which is about twice as efficient as the best currently available chemical engines, produces two pounds of thrust with a specific impulse (Isp) of 860 sec. Transfer times to GEO are projected to be on the order of one month. The launch and deployed configurations of the solar thermal upper stage (STUS) are depicted.

Emrich, William J.↗

A Probability-Base Alerting Logic for Aircraft on Parallel Approach

This document discusses the development and evaluation of an airborne collision alerting logic for aircraft on closely-spaced approaches to parallel runways. A novel methodology is used when links alerts to collision probabilities: alerting thresholds are set such that when the probability of a collision exceeds an acceptable hazard level an alert is issued. The logic was designed to limit the hazard level to that estimated for the Precision Runway Monitoring system: one accident in every one thousand blunders which trigger alerts. When the aircraft were constrained to be coaltitude, evaluations of a two-dimensional version of the alerting logic show that the achieved hazard level is approximately one accident in every 250 blunders. Problematic scenarios have been identified and corrections to the logic can be made. The evaluations also show that over eighty percent of all unnecessary alerts were issued during scenarios in which the miss distance would have been less than 1000 ft, indicating that the alerts may have been justified. Also, no unnecessary alerts were generated during normal approaches.

Carpenter, Brenda D.↗

Loads Produced During the Ingression and Egression of the Portable Foot Restraint on the Hubble Space Telescope

The Hubble Space Telescope (HST) was deployed from the Space Shuttle Discovery on April 25, 1990. It is capable of performing observations in the visible, near-ultraviolet, and near-infrared (1150 A to 1 mm). The HST weighs 12 tons, and collects light with an 8-ft-diameter mirror. The attitude control and maneuvering is performed by four of six gyroscopes, or reaction wheels. The HST contains fine guidance sensors that lock onto guide stars to reduce the spacecraft drift and increase the pointing accuracy. The HST was designed to last 15 years, with crewed service missions approximately every three years. The first service mission, STS-61, took place in 1993. The second service mission took place in 1997. In 1999, the STS-103 crew performed the third service mission to the HST. This mission's purpose was to replace the right sensor units and make improvements on the fine guidance sensors. To perform these tasks on the HST, the STS-103 crewmembers used a portable foot restraint to anchor themselves to the HST in the zero-gravity environment. The solar arrays currently used on the telescope are second-generation, and therefore susceptible to loads placed on the telescope. The crew and Mission Operations Directorate worried about the damage that the crew could possibly cause during ingress and egress of the PFR and by transferring loads to the solar arrays. The purpose of this study is to inform the crewmembers of the loads they are imparting on the HST, and train them to decrease these loads to a safer level. Minimizing these loads will significantly decrease the chance of crewmembers causing damage to the solar arrays while repairing the HST.

Ramsey, Susan↗

Support of NASA ADR/ Cross-Enterprise NRA Advanced Adiabatic Demagnetization Refrigerators for Continuous Cooling from 10K to 50mK, Development of a Heat Switch

Mechanical heat switches are used in conjunction with sorption refrigerators, adiabatic demagnetization refrigerators and for other cryogenic tasks including the pre-cooling cryogenic systems. They use a mechanical actuator which closes Au plated Cu jaws on an Au plated Cu bar. The thermal conductance in the closed position is essentially independent of the area of the jaws and proportional to the force applied. It varies linearly with T. It is approximately 10mW/K for 200 N at 1.5K. In some applications, the heat switch can be driven from outside the cryostat by a rotating rod and a screw. Such heat switches are available commercially from several sources. In other applications, including systems for space, it is desirable to drive the switch using a cold linear motor, or solenoid. Superconducting windings are used at temperatures s 4.2K to minimize power dissipation, but are not appropriate for pre-cooling a system at higher temperatures. This project was intended to improve the design of solenoid activated mechanical heat switches and to provide such switches as required to support the development of Advanced Adiabatic Demagnetization Refrigerators for Continuous Cooling from 10 K to 50 mK at GSFC. By the time funding began in 5/1/01, the immediate need for mechanical heat switches at GSFC had subsided but, at the same time, the opportunity had arisen to improve the design of mechanical heat switching by incorporating a "latching solenoid". In this device, the solenoid current is required only for changing the state of the switch and not during the whole time that the switch is closed.

Richards, Paul L.↗

Ionic Liquids Enabling Revolutionary Closed-Loop Life Support

Minimizing resupply from Earth is essential for future long duration manned missions. The current oxygen recovery system aboard the International Space Station is capable of recovering approximately 50% of the oxygen from metabolic carbon dioxide. For long duration manned missions, a minimum of 75% oxygen recovery is targeted with a goal of greater than 90%. Theoretically, the Bosch process can recover 100% of oxygen, making it a promising technology for oxygen recovery for long duration missions. However, the Bosch process produces elemental carbon which ultimately fouls the catalyst. Once the catalyst performance is compromised, it must be replaced resulting in undesired resupply mass. Based on the performance of a Bosch system designed by NASA in the 1990's, a three year Martian mission would require approximately 1315 kg (2850 lbs) of catalyst resupply. It may be possible to eliminate catalyst resupply with a fully regenerable system using an Ionic Liquid (IL)-based Bosch system. In 2016, we reported the feasibility of using ILs to produce an iron catalyst on a copper substrate and to regenerate the iron catalyst by extracting the iron from the copper substrate and product carbon. Additionally, we described a basic system concept for an IL-based Bosch. Here we report the results of efforts to scale catalyst preparation, catalyst regeneration, and to scale the carbon formation processing rate of a single reactor.

Brown, Brittany R.↗

Ionic Liquids Enabling Revolutionary Closed-Loop Life Support

Minimizing resupply from Earth is essential for future long duration manned missions. The current oxygen recovery system aboard the International Space Station is capable of recovering approximately 50% of the oxygen from metabolic carbon dioxide. For long duration manned missions, a minimum of 75% oxygen recovery is targeted with a goal of greater than 90%. Theoretically, the Bosch process can recover 100% of oxygen, making it a promising technology for oxygen recovery for long duration missions. However, the Bosch process produces elemental carbon which ultimately fouls the catalyst. Once the catalyst performance is compromised, it must be replaced resulting in undesired resupply mass. Based on the performance of a Bosch system designed by NASA in the 1990's, a three year Martian mission would require approximately 1315 kg (2850 lbs) of catalyst resupply. It may be possible to eliminate catalyst resupply with a fully regenerable system using an Ionic Liquid (IL)-based Bosch system. In 2016, we reported the feasibility of using ILs to produce an iron catalyst on a copper substrate and to regenerate the iron catalyst by extracting the iron from the copper substrate and product carbon. Additionally, we described a basic system concept for an IL-based Bosch. Here we report the results of efforts to scale catalyst preparation, to scale catalyst regeneration, and to scale the carbon formation processing rate of a single reactor.

Brown, Brittany R.↗

Soyuz Landing Risk Characterization

INTRODUCTION United States On-orbit Segment (USOS) astronauts have been returning to Earth from the International Space Station (ISS) aboard the Russian Soyuz vehicle since 2003. The energetics associated with Soyuz landings are comparable to our next generation of US space vehicles (Orion, Crew Dragon, and Starliner). Soyuz also lands crew in a similar state of spaceflight deconditioning that is anticipated using the future vehicles. A number of injuries have now been observed during these Soyuz landings. Currently it is unknown how Soyuz landing accelerations and the numbers and types of associated injuries relate to the new occupant protection requirements levied upon future space vehicles. Understanding this relationship will allow better quantification of the risk of injury for future spacecraft designs. METHODS An estimate of injury occurrence during Soyuz landings has been determined using data contained in NASA flight medicine databases and supplemented with data collected from crewmembers and flight surgeons. At the time of this abstract, 96 USOS astronauts have returned to Earth in the Soyuz (59 US, 31 International Partner, and 6 spaceflight participants). Of that total, data from 80 individual crew landings has been collected through this study as of 2021. Injuries are classified either as contusions/abrasions, Class I (minor, no medical follow-up), Class II (moderate, medical follow-up necessary), Class III (severe), or Class IV (life threatening). Current NASA occupant protection standards are primarily based on the Multi-axial Dynamic Response Index (MDRI), which is a simple lumped-parameter spring, mass, damper model tuned to human impact responses in three orthogonal axes. RESULTS Using what is known about Soyuz landing dynamics from airborne and drop test data, the MDRI predicts essentially no Class IV or III injuries, < 1% Class II injuries, and < 5% Class I injuries. Approximately one-third of all USOS crewmembers for whom data has been gathered have suffered some sort of injury related to landing in the Soyuz vehicle. Most of these injuries fall into the contusion/abrasion category (21.3 %) (n.b. This is the percent for whom contusion/abrasion was the worst injury. Those with class I or II injuries typically also received contusions/abrasions). Class I injuries have been sustained by 5.0% of all crew, and Class II injuries have been observed in 3.8%. No Class III or IV injuries have been sustained to date. Forty-three injuries have been documented, with some crewmembers sustaining more than one injury in a single landing. The knee was the most likely area of injury (n=9), followed by the back (n=8), then the arm (n=7). CONCLUSION Soyuz landing dynamics are the most comparable analog environment for the anticipated loads associated with Orion and commercial crew vehicle landings. The MDRI under predicts the percentage of Class II injuries experienced during Soyuz landings, but it is better at predicting Class I injury occurrences. However, if contusions/abrasions are included in the minor injury Class I category, then the MDRI vastly under predicts those injuries as well. Given this data, it is important to re-evaluate the expected injury rates for future vehicles and work toward improving the predictive tools for spaceflight use. Spaceflight deconditioning may account for some of the under prediction, and work is ongoing to assess the relationship between landing injuries and impact tolerance changes due to spaceflight deconditioning. Future work includes expanding this study to involve private space missions on new vehicles to better characterize the effects of time in flight, suit and seat design, and vehicle dynamics.

N Newby↗

Soyuz Landing Risk Characterization

INTRODUCTION United States On-orbit Segment (USOS) astronauts have been returning to Earth from the International Space Station (ISS) aboard the Russian Soyuz vehicle since 2003. The energetics associated with Soyuz landings are comparable to our next generation of US space vehicles (Orion, Crew Dragon, and Starliner). Soyuz also lands crew in a similar state of spaceflight deconditioning that is anticipated using the future vehicles. A number of injuries have now been observed during these Soyuz landings. Currently it is unknown how Soyuz landing accelerations and the numbers and types of associated injuries relate to the new occupant protection requirements levied upon future space vehicles. Understanding this relationship will allow better quantification of the risk of injury for future spacecraft designs. METHODS An estimate of injury occurrence during Soyuz landings has been determined using data contained in NASA flight medicine databases and supplemented with data collected from crew members and flight surgeons. At the time of this abstract, 96 USOS astronauts have returned to Earth in the Soyuz (59 US, 31 International Partner, and 6 spaceflight participants). Of that total, data from 80individual crew landings has been collected through this study as of September 2023. Injuries are classified either as contusions/abrasions, Class I (minor, no medical follow-up), Class II (moderate, medical follow-up necessary), Class III (severe), or Class IV (life threatening). Current NASA occupant protection standards are primarily based on the Multi-axial Dynamic Response Index (MDRI), which is a simple lumped-parameter spring, mass, damper model tuned to human impact responses in three orthogonal axes. RESULTS Using what is known about Soyuz landing dynamics from airborne and drop test data, the MDRI predicts essentially no Class IV or III injuries, < 1% Class II injuries, and < 5% Class I injuries. Approximately one-third of all USOS crewmembers for whom data has been gathered have suffered some sort of injury related to landing in the Soyuz vehicle. Most of these injuries fall into the contusion/abrasion category (21.3%) (n.b. This is the percent for whom contusion/abrasion was the worst injury. Those with class I or II injuries typically also received contusions/abrasions). Class I injuries have been sustained by 5.0% of all crew, and Class II injuries have been observed in 3.8%. No Class III or IV injuries have been sustained to date. Forty-three injuries have been documented, with some crewmembers sustaining more than one injury in a single landing. The knee was the most likely area of injury (n=9), followed by the back (n=8), then the arm (n=7). CONCLUSION Soyuz landing dynamics are the most comparable analog environment for the anticipated loads associated with Orion and commercial crew vehicle landings. The MDRI under predicts the percentage of Class II injuries experienced during Soyuz landings, but it is better at predicting Class I injury occurrences. However, if contusions/abrasions are included in the minor injury Class I category, then the MDRI vastly under predicts those injuries as well. Given this data, it is important to re-evaluate the expected injury rates for future vehicles and work toward improving the predictive tools for spaceflight use. Spaceflight deconditioning may account for some of the under prediction, and work is ongoing to assess the relationship between landing injuries and impact tolerance changes due to spaceflight deconditioning. Future work includes expanding this study to involve private space missions on new vehicles to better characterize the effects of time in flight, suit and seat design, and vehicle dynamics.

N Newby↗

Soyuz Landing Risk Characterization

INTRODUCTION United States On-orbit Segment (USOS) astronauts have been returning to Earth from the International Space Station (ISS) aboard the Russian Soyuz vehicle since 2003. The energetics associated with Soyuz landings are comparable to our next generation of US space vehicles (Orion, Crew Dragon, and Starliner). Soyuz also lands crew in a similar state of spaceflight deconditioning that is anticipated using the future vehicles. A number of injuries have now been observed during these Soyuz landings. Currently it is unknown how Soyuz landing accelerations and the numbers and types of associated injuries relate to the new occupant protection requirements levied upon future space vehicles. Understanding this relationship will allow better quantification of the risk of injury for future spacecraft designs. METHODS An estimate of injury occurrence during Soyuz landings has been determined using data contained in NASA flight medicine databases and supplemented with data collected from crewmembers and flight surgeons. At the time of this abstract, 96 USOS astronauts have returned to Earth in the Soyuz (59 US, 31 International Partner, and 6 spaceflight participants). Of that total, data from 80 individual crew landings has been collected through this study as of September 2023. Injuries are classified either as contusions/abrasions, Class I (minor, no medical follow-up), Class II (moderate, medical follow-up necessary), Class III (severe), or Class IV (life threatening). Current NASA occupant protection standards are primarily based on the Multi-axial Dynamic Response Index (MDRI), which is a simple lumped-parameter spring, mass, damper model tuned to human impact responses in three orthogonal axes. RESULTS Using what is known about Soyuz landing dynamics from airborne and drop test data, the MDRI predicts essentially no Class IV or III injuries, < 1% Class II injuries, and < 5% Class I injuries. Approximately one-third of all USOS crewmembers for whom data has been gathered have suffered some sort of injury related to landing in the Soyuz vehicle. Most of these injuries fall into the contusion/abrasion category (21.3 %) (n.b. This is the percent for whom contusion/abrasion was the worst injury. Those with class I or II injuries typically also received contusions/abrasions). Class I injuries have been sustained by 5.0% of all crew, and Class II injuries have been observed in 3.8%. No Class III or IV injuries have been sustained to date. Forty-three injuries have been documented, with some crewmembers sustaining more than one injury in a single landing. The knee was the most likely area of injury (n=9), followed by the back (n=8), then the arm (n=7). CONCLUSION Soyuz landing dynamics are the most comparable analog environment for the anticipated loads associated with Orion and commercial crew vehicle landings. The MDRI under predicts the percentage of Class II injuries experienced during Soyuz landings, but it is better at predicting Class I injury occurrences. However, if contusions/abrasions are included in the minor injury Class I category, then the MDRI vastly under predicts those injuries as well. Given this data, it is important to re-evaluate the expected injury rates for future vehicles and work toward improving the predictive tools for spaceflight use. Spaceflight deconditioning may account for some of the under prediction, and work is ongoing to assess the relationship between landing injuries and impact tolerance changes due to spaceflight deconditioning. Future work includes expanding this study to involve private space missions on new vehicles to better characterize the effects of time in flight, suit and seat design, and vehicle dynamics.

P Greenhalgh↗