Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “alpha particle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Relativistic Electrons Observed at UARS and the Interpretation of their Storm-Associated Intensity Variations

The High Energy Particle Spectrometer (HEPS) instrument on the Upper Atmosphere Research Satellite (UARS) provides a database of electron intensities well resolved in energy and pitch-angle. Because of its 57 deg. orbital inclination, UARS encounters with magnetic shells L greater than 2 occur quite far off-equator (B/B (sub 0) greater than 9), corresponding to equatorial pitch angle alpha (sub 0) greater than 20 deg. Data acquired by HEPS (October 1991 through September 1994) span the declining phase of Solar Cycle 22. To reveal the storm-associated time dependence of relativistic electron intensities over the wide range of energies (50 keV to 5 MeV) covered by HEPS, we divide the daily average of the measured spectrum at a given L value (bin width = 0.25) by the corresponding 500-day average and plot the results with a color scale that spans only 2.5 decades. The data show that our off-equatorial electron intensities typically increase with time after the end of recovery phase (not during main phase or recovery phase) of each geomagnetic storm. The delay in off-equatorial energetic electron response and the subsequent lifetime of the corresponding electron flux enhancement seem to increase with particle energy above 300 keV. The trend below 300 keV seems to be opposite, such that the delay varies inversely with electron energy. Our working hypothesis for interpretation is that stormtime radial transport tends to increase the phase-space densities of trapped relativistic electrons but typically leads to a flux increases at specified energies only as the current (as indicated by Dst) decays. Flux enhancements in early recovery phase are greatest for equatorially mirroring electrons, and to pitch-angle anisotropies are initially large. Subsequent pitch-angle diffusion broadens the flux enhancement to particles that mirror off equator, thus gradually increasing low-altitude electron intensities (as detected by HEPS/UARS) on time scales equal to about 20% of corresponding lifetimes against diffusion into the loss cone. Alternative interpretations will also be examined.

Pesnell, W. D.↗
DOE OSTI2024

Transverse momentum-dependent heavy-quark fragmentation at next-to-leading order

The transverse momentum-dependent fragmentation functions (TMD FFs) of heavy (bottom and charm) quarks, which we recently introduced, are universal building blocks that enter predictions for a large number of observables involving final-state heavy quarks or hadrons. They enable the extension of fixed-order subtraction schemes to quasi-collinear limits, and are of particular interest in their own right as probes of the nonperturbative dynamics of hadronization. In this paper we calculate all TMD FFs involving heavy quarks and the associated TMD matrix element in heavy-quark effective theory (HQET) to next-to-leading order in the strong interaction. Our results confirm the renormalization properties, large-mass, and small-mass consistency relations predicted in our earlier work. We also derive and confirm a prediction for the large-z behavior of the heavy-quark TMD FF by extending, for the first time, the formalism of joint resummation to capture quark mass effects in heavy-quark fragmentation. Our final results in position space agree with those of a recent calculation by another group that used a highly orthogonal organization of singularities in the intermediate momentum-space steps, providing a strong independent cross check. As an immediate application, we present the complete quark mass dependence of the energy-energy correlator (EEC) in the back-to-back limit at $\mathcal{O}\left({\alpha}_s\right)$.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1973

The chromospheric association of the metric type 3 bursts - implications concerning the acceleration of solar electrons and the active streamers

In two recent papers it was shown that the metric type 3 emission is closely related to a transient perturbation seen in absorption in the H alpha line. In addition, this perturbation sometimes triggers a flare, sometimes not. This can explain why the type 3 have a poor H alpha flare correlation rate and still are a typical flash phase emission when flare-associated. The characteristics are summarized of the new association proposed. It is assumed that 10 to 100 keV electrons are accelerated in connection with a particular kind of transient H alpha absorbing feature. For as yet undetermined reasons, this process would often, but not always, result in a more efficient acceleration coincident with the early phase of the optical flare. The possibilities that this process could lead occasionally to long lasting subrelativistic particle emissive region are explored.

Axisa, F.↗
NASA NTRS1974

A hysteresis effect in cosmic ray modulation

The rigidity dependence is investigated in the modulation of cosmic ray protons and alphas at intermediate (2-13 Gv) rigidities during the declines and recoveries of the cosmic ray flux near cosmic ray minimum. The results include the finding that sudden changes in the modulation of the primary cosmic rays are initiated by large solar particle outflow and begin as type I Forbush decreases. Typically, the modulation spectrum becomes flatter at intermediate rigidity below 13 Gv and steeper at rigidities above 13 Gv during early recovery.

Verschell, H. J.↗
NASA NTRS1975

Hard X-ray bursts from flare behind the solar limb

The determination of the location of the region of origin of hard X-rays is important in evaluating the importance of 10-100 keV electrons in solar flares and in understanding flare particle acceleration. At present only limb-occulted events are available to give some information on the height of X-ray emission. In fifteen months of OSO-7 operation, nine major soft X-ray events had no reported correlated H alpha flare. We examine the hard X-ray spectra of eight of these events with good candidate X-ray flare producing active regions making limb transit at the time of the soft X-ray bursts. All eight bursts had significant X-ray emission in the 30-44 keV range, but only one had flux at the 3 sigma level above 44 keV. The data are consistent with most X-ray emission occurring in the lower chromosphere, but some electron trapping at high altitudes is necessary to explain the small nonthermal fluxes observed.

Mckenzie, D. L.↗
NASA NTRS1988

Evidence for change in particle excitation of Jupiter's atmosphere 1968-1979

Analysis of the Pioneer 10 and rocket observations of disk averaged emission from the sunlit atmosphere of Jupiter indicates that the spectrally integrated EUV brightness was reduced by at least a factor of two relative to Voyager spacecraft observations in 1979. Most of the variation is caused by the H Ly-alpha component in the spectrum, which was reduced roughly one order of magnitude near the time of solar minimum in 1972-1973. Although the analysis of the data does not produce entirely consistent results, the weight of evidence points to a factor of order roughly two lower abundance of H in Jupiter's atmosphere in 1972-1973 relative to 1979. The low emission rate in H Ly-alpha near the time of solar minimum in this proposed scenario is caused by an electroglow energy depositon rate reduced by a factor of roughly three. The apparent reduced abundance of H implies a reduced thermospheric temperature, even under the assumption of a constant electroglow deposition rate.

Shemansky, D. E.↗
NASA NTRS2002

Operation of A Sunpower M87 Cryocooler In A Magnetic Field

The Alpha Magnetic Spectrometer-02 (AMS-02) is an experiment that will be flown as an attached payload on the International Space Station to detect dark matter and antimatter. It uses large superconducting magnets cooled with superfluid helium to bend the path of cosmic particles through a series of detectors, which then measure the mass, speed, charge, and direction of the particles. Four Sunpower M87N Stirling-cycle cryocoolers are used to extend the mission life by cooling the outer vapor-cooled shield of the dewar. The main magnet coils are separated by a distance of approximately 1 m and the coolers are located approximately 1.5 m from the center line of the magnet, where the field is as high as 925 gauss perpendicular to the cryocooler axis and 400 gauss along the cryocooler axis. Interactions between the applied magnetic field and the linear motor may result in additional forces and torques on the compressor piston. Motion of the compressor arid displacer pistons through the magnetic field spatial gradients will generate eddy currents. Additional eddy currents are created during magnet charge, discharge, and quench by the time-varying magnetic field. The results of tests to determine the magnitude of the forces, torques, and heating effects, as well as the need for additional magnetic shielding, are presented.

Breon, S. R.↗
DOE OSTI2021

Self-consistent core-pedestal ITER scenario modeling

The purpose of these integrated ITER simulations is to identify dependencies that can impact the performance of ITER. The dependence of fusion power production, temperature and density pedestals, and core profiles on varying magnetic-q, edge density fueling strength, neoclassical transport, magnetic field strength, and alpha heating, are examined. It is noted that ion modes usually dominate the interior, while electron modes dominate the barrier. The electron mode without flow shear is substantially stronger. The q increase tends to cause more kinetic ballooning modes at the edge and the q decrease means that the peeling is getting worse, but the ballooning is getting better. The large edge q tends to provide hollow density while small edge q gives normal density profile. This is consistent with the observation that the density of particles is inversely proportional to the density of the plasma current. The rise in the source of the edge particle increases the density of the edge and the reaction rate close to the edge increases temperature fluxes, resulting in weak pedestal barriers. When neoclassical transport is turned off or the strength of B-field is increased, the pronounced edge barriers are identified. In addition, a distinct effect on the magnetohydrodynamic (MHD) modes is observed due to the increased B-field. The interesting aspect is that the barrier collapses about q = 2 as the stability of MHD has decreased to replace the barrier with a continuous slope but with roughly the same fusion power. This would actually be good for a reactor. The slope of the H-mode pedestal is found to be reduced due to the alpha heating. It is expected that the problem of edge-localized modes causing damage to the first wall will be eased. The effects of circular, elongated, and general geometry on plasma profiles are also compared and contrasted. The circular geometry has a hollow density profile and no edge or internal thermal transport barrier (ETB or ITB). However, both ETBs and ITBs can be found in the elongated geometry. In general geometry, there is a weaker ETB, comparable ITBs, but a higher edge particle transport barrier than in elongated geometry. Higher density near the edge, on the other hand, causes more wall erosion, so elongated geometry might be the best option.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2014

Turbulent Concentration of MM-Size Particles in the Protoplanetary Nebula: Scaled-Dependent Multiplier Functions

The initial accretion of primitive bodies (asteroids and TNOs) from freely-floating nebula particles remains problematic. Here we focus on the asteroids where constituent particle (read "chondrule") sizes are observationally known; similar arguments will hold for TNOs, but the constituent particles in those regions will be smaller, or will be fluffy aggregates, and are unobserved. Traditional growth-bysticking models encounter a formidable "meter-size barrier" [1] (or even a mm-cm-size barrier [2]) in turbulent nebulae, while nonturbulent nebulae form large asteroids too quickly to explain long spreads in formation times, or the dearth of melted asteroids [3]. Even if growth by sticking could somehow breach the meter size barrier, other obstacles are encountered through the 1-10km size range [4]. Another clue regarding planetesimal formation is an apparent 100km diameter peak in the pre-depletion, pre-erosion mass distribution of asteroids [5]; scenarios leading directly from independent nebula particulates to this size, which avoid the problematic m-km size range, could be called "leapfrog" scenarios [6-8]. The leapfrog scenario we have studied in detail involves formation of dense clumps of aerodynamically selected, typically mm-size particles in turbulence, which can under certain conditions shrink inexorably on 100-1000 orbit timescales and form 10-100km diameter sandpile planetesimals. The typical sizes of planetesimals and the rate of their formation [7,8] are determined by a statistical model with properties inferred from large numerical simulations of turbulence [9]. Nebula turbulence can be described by its Reynolds number Re = L/eta sup(4/3), where L = ETA alpha sup (1/2) the largest eddy scale, H is the nebula gas vertical scale height, and α the nebula turbulent viscosity parameter, and η is the Kolmogorov or smallest scale in turbulence (typically about 1km), with eddy turnover time tη. In the nebula, Re is far larger than any numerical simulation can handle, so some physical model is needed to extend the results of numerical simulations to nebula conditions.

protoplanetary nebula↗
NASA NTRS1990

Aerodynamics support of research instrument development

A new velocimetry system is currently being developed at NASA LaRC. The device, known as a Doppler global velocimeter (DGV), can record three velocity components within a plane simultaneously and in near real time. To make measurements the DGV, like many other velocimetry systems, relies on the scattering of light from numerous small particles in a flow field. The particles or seeds are illuminated by a sheet of laser light and viewed by two CCD cameras. The scattered light from the particles will have a frequency which is a function of the source laser light frequency, the viewing angle, and most importantly the seed velocities. By determining the scattered light intensity the velocity can be measured at all points within the light sheet simultaneously. Upon completion of DGV component construction and initial check out a series of tests in the Basic Aerodynamic Research (wind) Tunnel (BART) are scheduled to verify instrument operation and accuracy. If the results are satisfactory, application of the DGV to flight measurements on the F-18 High Alpha Research Vehicle (HARV) are planned. The DGV verification test in the BART facility will utilize a 75 degree swept delta wing model. A major task undertaken this summer included evaluation of previous results for this model. A specific series of tests matching exactly the previous tests and exploring new DGV capabilities were developed and suggested. Another task undertaken was to study DGV system installation possibilities in the F-18 HARV aircraft. In addition, a simple seeding system modification was developed and utilized to make Particle Imaging Velocimetry (PIV) measurements in the BART facility.

Miller, L. Scott↗
DOE OSTI2023

Development of digital electronics for the search of SHE nuclei using GARIS-II/III at RIKEN

This work describes the implementation of a digital data acquisition system for the search and study of short-lived isotopes or superheavy elements at the GARIS-III separator at the RIKEN Nishina Center. Here a reduction to 26 ± 0.5 keV in the average value of the Full Width at Half Maximum of the alpha spectrum at 7.133 MeV was achieved, combined with a reduction of the dead time of the overall system to around a few tens of nanoseconds for the detection of very fast decay chains. Moreover, we measured a reduction of the background induced by particles crossing the implantation detector using pulse shape analysis techniques. The detail of the optimization and analysis will be presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Required toroidal confinement for fusion and omnigeneity

Deuterium–tritium (DT) burning requires a long energy confinement times compared to collision times, so the particle distribution functions must approximate local Maxwellians. Non-equilibrium thermodynamics is applicable, which gives relations among transport, entropy production, the collision frequency, and the deviation from a Maxwellian. The distribution functions are given by the Fokker–Planck equation, which is an advection–diffusion equation. A large hyperbolic operator, the Vlasov operator with the particle trajectories as its characteristics, equals a small diffusive operator, the collision operator. The collisionless particle trajectories would be chaotic in stellarators without careful optimization. This would lead to rapid entropy production and transport—far beyond what is consistent with a self-sustaining DT burn. Omnigeneity is the weakest general condition that is consistent with a sufficiently small entropy production associated with the thermal particle trajectories. Omnigeneity requires that the contours of constant magnetic field strength be unbounded in at least one of the two angular coordinates in magnetic surfaces and that there be a symmetry in the field-strength wells along the field lines. Even in omnigenous plasmas, fluctuations due to microturbulence can produce chaotic particle trajectories and the gyro-Bohm transport is seen in many stellarator and tokamak experiments. The higher the plasma temperature above 10 keV, the smaller the transport must be compared to gyro-Bohm for a self-sustaining DT burn. The hot alphas of DT fusion heat the electrons. When the ion–electron equilibration time is long compared to the ion energy confinement time, a self-sustaining DT burn is not possible, which sets a limit on the electron temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1994

Two-fluid simulations of galaxy formation

We investigate the formation of galaxies and larger structure with a simulation modeling two gravitationally coupled fluids representing dark matter and baryons. The baryon gas dynamics are calculated with a smoothed particle hydrodynamics (SPH) method, and the physics modeled includes thermal pressure, shock heating, and radiative cooling. We simulate a 16 Mpc periodic cube with 64(exp 3) particles in each fluid and 10% baryon mass fraction. We confirm, for the first time experimentally, disk formation as a natural consequence of hierarchical clustering in a large-scale cosmological environment. The majority of isolated galaxies exhibit centrifugally supported disks. A power-law relation between cold baryonic mass and maximum rotation velocity is found, M varies as nu(sub rot)(exp alpha) with alpha = 2.5 after correcting for differential numerical resolution. Both the spatial and velocity distributions of the simulated galaxies are biased with respect to the dark matter. A counts-in-cells analysis indicates that an unphysical degree of merging in the central cluster is likely responsible for the antibias signal in the correlation function. A robust, scale-dependent velocity bias is measured. The ratio of galaxy to dark matter pairwise velocity dispersions on a scale of 1 Mpc is 0.7. The amplitude is only mildly dependent on redshift or mass cutoff and scales with separation as r(exp 0.2). The degree to which these results depend on numerical parameters is discussed. Mass resolution plays a key role in controlling the resulting fraction of cold, dense baryons. The mass fraction associated with galaxies decreases by a factor of approximately greater than 3 when the mass per particle is increased by a factor 8. Photoionization and energy input from supernova will have to be included to determine more carefully the fraction of highly dissipated material and the characteristics of the stellar component of galaxies.

Evrard, August E.↗
NASA NTRS1998

Analysis of IUE Observations of Hydrogen in Comets

The 15-years worth of hydrogen Lyman-alpha observations of cometary comae obtained with the International Ultraviolet Explorer (IUE) satellite had gone generally unanalyzed because of two main modeling complications. First, the inner comae of many bright (gas productive) comets are often optically thick to solar Lyman-alpha radiation. Second, even in the case of a small comet (low gas production) the large IUE aperture is quite small as compared with the immense size of the hydrogen coma, so an accurate model which properly accounts for the spatial distribution of the coma is required to invert the infrared brightnesses to column densities and finally to H atom production rates. Our Monte Carlo particle trajectory model (MCPTM), which for the first time provides the realistic full phase space distribution of H atoms throughout the coma has been used as the basis for the analysis of IUE observations of the inner coma. The MCPTM includes the effects of the vectorial ejection of the H atoms upon dissociation of their parent species (H2O and OH) and of their partial collisional thermalization. Both of these effects are crucial to characterize the velocity distribution of the H atoms. This combination of the MCPTM and spherical radiative transfer code had already been shown to be successful in understanding the moderately optically thick coma of comet P/Giacobini-Zinner and the coma of comet Halley that varied from being slightly to very optically thick. Both of these comets were observed during solar minimum conditions. Solar activity affects both the photochemistry of water and the solar Lyman-alpha radiation flux. The overall plan of this program here was to concentrate on comets observed by IUE at other time during the solar cycle, most importantly during the two solar maxima of 1980 and 1990. Described herein are the work performed and the results obtained.

Combi, Michael R.↗
NASA NTRS2001

Composition and physical properties of starch in microgravity-grown plants

The effect of spaceflight on starch development in soybean (Glycine max L., BRIC-03) and potato (Solanum tuberosum, Astroculture-05) was compared with ground controls by biophysical and biochemical measurements. Starch grains from plants from both flights were on average 20-50% smaller in diameter than ground controls. The ratio delta X/delta rho (delta X --difference of magnetic susceptibilities, delta rho--difference of densities between starch and water) of starch grains was ca. 15% and 4% higher for space-grown soybean cotyledons and potato tubers, respectively, than in corresponding ground controls. Since the densities of particles were similar for all samples (1.36 to 1.38 g/cm3), the observed difference in delta X/delta rho was due to different magnetic susceptibilities and indicates modified composition of starch grains. In starch preparations from soybean cotyledons (BRIC-03) subjected to controlled enzymatic degradation with alpha-amylase for 24 hours, 77 +/- 6% of the starch from the flight cotyledons was degraded compared to 58 +/- 12% in ground controls. The amylose content in starch was also higher in space-grown tissues. The good correlation between the amylose content and delta X/delta rho suggests, that the magnetic susceptibility of starch grains is related to their amylose content. Since the seedlings from the BRIC-03 experiment showed elevated post-flight ethylene levels, material from another flight experiment (GENEX) which had normal levels of ethylene was examined and showed no difference to ground controls in size distribution, density, delta X/delta rho and amylose content. Therefore the role of ethylene appears to be more important for changes in starch metabolism than microgravity. c2001 COSPAR. Published by Elsevier Science Ltd. All rights reserved.

NASA Experiment Number 9305014 2/2↗
NASA NTRS2004

Propagation of Cosmic Rays: Nuclear Physics in Cosmic-ray Studies

The nuclei fraction in cosmic rays (CR) far exceeds the fraction of other CR species, such as antiprotons, electrons, and positrons. Thus the majority of information obtained from CR studies is based on interpretation of isotopic abundances using CR propagation models where the nuclear data and isotopic production cross sections in p- and alpha-induced reactions are the key elements. This paper presents an introduction to the astrophysics of CR and diffuse gamma-rays and dimsses some of the puzzles that have emerged recently due to more precise data and improved propagation models. Merging with cosmology and particle physics, astrophysics of CR has become a very dynamic field with a large potential of breakthrough and discoveries in the near fume. Exploiting the data collected by the CR experiments to the fullest requires accurate nuclear cross sections.

Moskalenko, Igor V.↗
DOE OSTI2021

A 1D Lyman-alpha profile camera for plasma edge neutral studies on the DIII-D tokamak

A one dimensional, absolutely calibrated pinhole camera system was installed on the DIII-D tokamak to measure edge Lyman-alpha (Ly-α) emission from hydrogen isotopes, which can be used to infer neutral density and ionization rate profiles. The system is composed of two cameras, each providing a toroidal fan of 20 lines of sight, viewing the plasma edge on the inboard and outboard side of DIII-D. The cameras’ views lie in a horizontal plane 77 cm below the midplane. At its tangency radius, each channel provides a radial resolution of ~2 cm full width at half maximum (FWHM) with a total coverage of 22 cm. Each camera consists of a rectangular pinhole, Ly-α reflective mirror, narrow-band Ly-α transmission filter, and a 20 channel AXUV photodetector. The combined mirror and transmission filter have a FWHM of 5 nm, centered near the Ly-α wavelength of 121.6nm and is capable of rejecting significant, parasitic carbon-III (C-III) emission from intrinsic plasma impurities. To provide a high spatial resolution measurement in a compact footprint, the camera utilizes advanced engineering and manufacturing techniques including 3D printing, high stability mirror mounts, and a novel alignment procedure. Absolutely calibrated, spatially resolved Ly-α brightness measurements utilize a bright, isolated line with low parasitic surface reflections and enable quantitative comparison to modeling to study divertor neutral leakage, main chamber fueling, and radial particle transport.

Ionization Rate↗
NASA NTRS1998

Hydroxyapatite fiber reinforced poly(alpha-hydroxy ester) foams for bone regeneration

A process has been developed to manufacture biodegradable composite foams of poly(DL-lactic-co-glycolic acid) (PLGA) and hydroxyapatite short fibers for use in bone regeneration. The processing technique allows the manufacture of three-dimensional foam scaffolds and involves the formation of a composite material consisting of a porogen material (either gelatin microspheres or salt particles) and hydroxyapatite short fibers embedded in a PLGA matrix. After the porogen is leached out, an open-cell composite foam remains which has a pore size and morphology defined by the porogen. By changing the weight fraction of the leachable component it was possible to produce composite foams with controlled porosities ranging from 0.47 +/- 0.02 to 0.85 +/- 0.01 (n = 3). Up to a polymer:fiber ratio of 7:6, short hydroxyapatite fibers served to reinforce low-porosity PLGA foams manufactured using gelatin microspheres as a porogen. Foams with a compressive yield strength up to 2.82 +/- 0.63 MPa (n = 3) and a porosity of 0.47 +/- 0.02 (n = 3) were manufactured using a polymer:fiber weight ratio of 7:6. In contrast, high-porosity composite foams (up to 0.81 +/- 0.02, n = 3) suitable for cell seeding were not reinforced by the introduction of increasing quantities of hydroxyapatite short fibers. We were therefore able to manufacture high-porosity foams which may be seeded with cells but which have minimal compressive yield strength, or low porosity foams with enhanced osteoconductivity and compressive yield strength.

NASA Discipline Cell Biology↗