Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aeroelastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Time simulation of flutter with large stiffness changes

Time simulation of flutter, involving large local structural changes, is formulated with a state-space model that is based on a relatively small number of generalized coordinates. Free-free vibration modes are first calculated for a nominal finite-element model with relatively large fictitious masses located at the area of structural changes. A low-frequency subset of these modes is then transformed into a set of structural modal coordinates with which the entire simulation is performed. These generalized coordinates and the associated oscillatory aerodynamic force coefficient matrices are used to construct an efficient time-domain, state-space model for basic aeroelastic case. The time simulation can then be performed by simply changing the mass, stiffness and damping coupling terms when structural changes occur. It is shown that the size of the aeroelastic model required for time simulation with large structural changes at a few a priori known locations is similar to that required for direct analysis of a single structural case. The method is applied to the simulation of an aeroelastic wind-tunnel model. The diverging oscillations are followed by the activation of a tip-ballast decoupling mechanism that stabilizes the system but may cause significant transient overshoots.

Karpel, M.↗
NASA NTRS1992

Extension and validation of an unsteady wake model for rotors

A new three-dimensional, finite-state induced-flow model is extended to treat nonlinearities associated with the mass flow induced through the rotor plane. This new theory is then applied to the correlation of a recent set of unsteady, hover laser Doppler velocimetry inflow measurements conducted in the Aeroelastic Rotor Test Chamber at Georgia Institute of Technology. Although the model is intended primarily as a representation of unsteady aerodynamics for aeroelasticity applications, the results show that it has an excellent capability in predicting the inflow distribution in hover except near the root and tip. In addition, the computed unsteady spanwise lift distribution of a rotor is compared with that from an unsteady vortex lattice method for pitch oscillations at various frequencies. The new model is shown to be capable of prediction of unsteady loads typical of aeroelastic response.

Su, AY↗
NASA NTRS1992

Buffet test in the National Transonic Facility

A buffet test of a commercial transport model was accomplished in the National Transonic Facility at the NASA Langley Research Center. This aeroelastic test was unprecedented for this wind tunnel and posed a high risk to the facility. This paper presents the test results from a structural dynamics and aeroelastic response point of view and describes the activities required for the safety analysis and risk assessment. The test was conducted in the same manner as a flutter test and employed onboard dynamic instrumentation, real time dynamic data monitoring, automatic, and manual tunnel interlock systems for protecting the model. The procedures and test techniques employed for this test are expected to serve as the basis for future aeroelastic testing in the National Transonic Facility. This test program was a cooperative effort between the Boeing Commercial Airplane Company and the NASA Langley Research Center.

Young, Clarence P., Jr.↗
NASA NTRS1992

Stochastic sensitivity measure for mistuned high-performance turbines

A stochastic measure of sensitivity is developed in order to predict the effects of small random blade mistuning on the dynamic aeroelastic response of turbomachinery blade assemblies. This sensitivity measure is based solely on the nominal system design (i.e., on tuned system information), which makes it extremely easy and inexpensive to calculate. The measure has the potential to become a valuable design tool that will enable designers to evaluate mistuning effects at a preliminary design stage and thus assess the need for a full mistuned rotor analysis. The predictive capability of the sensitivity measure is illustrated by examining the effects of mistuning on the aeroelastic modes of the first stage of the oxidizer turbopump in the Space Shuttle Main Engine. Results from a full analysis mistuned systems confirm that the simple stochastic sensitivity measure predicts consistently the drastic changes due to misturning and the localization of aeroelastic vibration to a few blades.

Murthy, Durbha V.↗
NASA NTRS1993

Simulation of tail buffet using delta wing-vertical tail configuration

Computational simulation of the vertical tail buffet problem is accomplished using a delta wing-vertical tail configuration. Flow conditions are selected such that the wing primary-vortex cores experience vortex breakdown and the resulting flow interacts with the vertical tail. This multidisciplinary problem is solved successively using three sets of equations for the fluid flow, aeroelastic deflections and grid displacements. For the fluid dynamics part, the unsteady, compressible, full Navier-Stokes equations are solved accurately in time using an implicit, upwind, flux-difference splitting, finite-volume scheme. For the aeroelastic part, the aeroelastic equation for bending vibrations is solved accurately in time using the Galerkin method and the four-stage Runge-Kutta scheme. The grid for the fluid dynamics computations is updated every few time steps using a third set of interpolation equations. The computational application includes a delta wing of aspect ratio 1 and a rectangular vertical tail of aspect ratio 2, which is placed at 0.5 root-chord length downstream of the wing trailing edge. The wing angle of attack is 35 deg and the flow Mach number and Reynolds number are 0.4 and 10,000, respectively.

Kandil, Osama A.↗
NASA NTRS1993

Finite element calculations of transonic flutter in cascades

Aeroelastic stability and response of turbomachinery cascades operating in the transonic regime are explored using a new computational approach. The two-dimensional unsteady Euler equations are used to model the transonic cascade flows, and the cascade blades are modeled as thin plates. To minimize the discretization incompatibility, both the fluid and the solid domains are discretized using finite element procedures. The fluid and the structural models are coupled at the element level by introducing a channel theory, which is analogous to a strip theory in the classical sense. The system of space-discretized equations is marched forward in time using an explicit four-stage Runge-Kutta scheme. Results of free vibration analyses of typical blades are presented and compared to published finite element and Rayleigh-Ritz results. Aeroelastic stability and response characteristics of several transonic cascades are investigated using the new quasi-3D model. These results demonstrate the present 3D finite element blade model is capable of capturing aeroelastic instabilities involving higher modes, including (plate-type) camber bending modes.

Hsiao, Chingteng↗
NASA NTRS1993

Issac, Jason Cherian ses in transonic flow

Flutter analysis of a two degree of freedom airfoil in compressible flow is performed using a state-space representation of the unsteady aerodynamic behavior. Indicial response functions are used to represent the normal force and moment response of the airfoil. The structural equations of motion of the airfoil with bending and torsional degrees of freedom are coupled to the unsteady air loads and the aeroelastic system so modelled is solved as an eigenvalue problem to determine the stability. The aeroelastic equations are also directly integrated with respect to time and the time-domain results compared with the results from the eigenanalysis. A good agreement is obtained. The derivatives of the flutter speed obtained from the eigenanalysis are calculated with respect to the mass and stiffness parameters by both analytical and finite-difference methods for various transonic Mach numbers. The experience gained from the two degree of freedom model is applied to study the sensitivity of the flutter response of a wing with respect to various shape parameters. The parameters being considered are as follows: (1) aspect ratio; (2) surface area of the wing; (3) taper ratio; and (4) sweep. The wing deflections are represented by Chebyshev polynomials. The compressible aerodynamic state-space model used for the airfoil section is extended to represent the unsteady aerodynamic forces on a generally laminated tapered skewed wing. The aeroelastic equations are solved as an eigenvalue problem to determine the flutter speed of the wing. The derivatives of the flutter speed with respect to the shape parameters are calculated by both analytical and finite difference methods.

Issac, Jason Cherion↗
NASA NTRS1993

Wing design for a civil tiltrotor transport aircraft: A preliminary study

A preliminary study was conducted on the design of the wing-box structure for a civil tiltrotor transport aircraft. The wing structural weight is to be minimized subject to structural and aeroelastic constraints. The composite wing-box structure is composed of skin, stringers, ribs, and spars. The design variables include skin ply thicknesses and orientations and spar cap and stringer cross-sectional areas. With the total task defined, an initial study was conducted to learn more about the intricate dynamic and aeroelastic characteristics of the tiltrotor aircraft and their roles in the wing design. Also, some work was done on the wing finite-element modeling (via PATRAN) which would be used in structural analysis and optimization. Initial studies indicate that in order to limit the wing/rotor aeroelastic and dynamic interactions in the preliminary design, the cruise speed, rotor system, and wing geometric attributes must all be held fixed.

Rais-Rohani, Masoud↗
NASA NTRS1997

Multidisciplinary Optimization of Tilt Rotor Blades Using Comprehensive Composite Modeling Technique

An optimization procedure is developed for addressing the design of composite tilt rotor blades. A comprehensive technique, based on a higher-order laminate theory, is developed for the analysis of the thick composite load-carrying sections, modeled as box beams, in the blade. The theory, which is based on a refined displacement field, is a three-dimensional model which approximates the elasticity solution so that the beam cross-sectional properties are not reduced to one-dimensional beam parameters. Both inplane and out-of-plane warping are included automatically in the formulation. The model can accurately capture the transverse shear stresses through the thickness of each wall while satisfying stress free boundary conditions on the inner and outer surfaces of the beam. The aerodynamic loads on the blade are calculated using the classical blade element momentum theory. Analytical expressions for the lift and drag are obtained based on the blade planform with corrections for the high lift capability of rotor blades. The aerodynamic analysis is coupled with the structural model to formulate the complete coupled equations of motion for aeroelastic analyses. Finally, a multidisciplinary optimization procedure is developed to improve the aerodynamic, structural and aeroelastic performance of the tilt rotor aircraft. The objective functions include the figure of merit in hover and the high speed cruise propulsive efficiency. Structural, aerodynamic and aeroelastic stability criteria are imposed as constraints on the problem. The Kreisselmeier-Steinhauser function is used to formulate the multiobjective function problem. The search direction is determined by the Broyden-Fletcher-Goldfarb-Shanno algorithm. The optimum results are compared with the baseline values and show significant improvements in the overall performance of the tilt rotor blade.

Chattopadhyay, Aditi↗
NASA NTRS2000

Functionality Improvements to Overaero

The functionality of the overset, static aeroelasticity, Navier-Stokes flow solver OVERAERO was increased by adding capability to the flow solver and enhancing code performance. Improvements were made to the fluids/structure interface, an MLP version of the parallel OVERAERO code was developed, and the OVERAERO-MPI code was ported to the Cray T3E. The OVERFLOW-MPI and OVERAERO-MPI codes were tested successfully on the IPG testbed and a means of reducing communication overhead within OVERFLOW-MPI was investigated. To solve an aeroelastic problem computationally, a structures grid surface definition and a fluids grid surface definition are required. Typically, the structures grid surface has a lower fidelity than the fluids grid surface. Thus, the methods developed to transfer data between the two grid systems are vital to the accuracy and efficiency of the aeroelasticity code. The fluids/structures interface developed for the OVERAERO code was improved to more accurately treat fluids surfaces that bridge between two different structural surfaces. For example, the method allowed the forward portion of a flap track fairing to deform with the wing and the aft end of the fairing to deform with the flap. A tightly-coupled version of the code based on OVERFLOW-MLP was developed to improve code performance on the SGI Origin 2000. This required a new parallelization strategy to couple the fluids and structures codes. The OVERAERO-MPI code was ported to the Cray T3E to extend the usability of the code. The port required extensive use of dynamic memory management techniques to fit large problems within the memory limitations of the T3E. The OVERFLOW-MPI and OVERAERO-MPI codes were tested on the IPG testbed being developed within NASA. For small problems with minimal data transfer between grids, there was little to no performance penalty spreading the computation across two machines. For very large problems, methods were developed to minimize intermachine communication via the grid partitioning scheme. By minimizing the intermachine communication requirements of the problem, it may still be beneficial to run a tightly-coupled flow solver across two machines within the IPG.

Gee, Ken↗
NASA NTRS1998

Computational Investigation and Validation of Twin-Tail Buffet Response Including Dynamics and Control

Multidisciplinary tools for prediction of single rectangular-tail buffet are extended to single swept-back-tail buffet in transonic-speed flow, and multidisciplinary tools for prediction and control of twin-tail buffet are developed and presented. The configuration model consists of a sharp-edged delta wing with single or twin tails that are oriented normal to the wing surface. The tails are treated as cantilevered beams fixed at the root and allowed to oscillate in both bending and torsion. This complex multidisciplinary problem is solved sequentially using three sets of equations on a dynamic single or multi-block grid structure. The first set is the unsteady, compressible, Reynolds-averaged Navier-Stokes equations which are used for obtaining the flow field vector and the aerodynamic loads on the tails. The Navier-Stokes equations are solved accurately in time using the implicit, upwind, flux-difference splitting, finite volume scheme. The second set is the coupled bending and torsion aeroelastic equations of cantilevered beams which are used for obtaining the bending and torsion deflections of the tails. The aeroelastic equations'are solved accurately in time using, a fifth-order-accurate Runge-Kutta scheme. The third set is the grid-displacement equations and the rigid-body dynamics equations, which are used for updating the grid coordinates due to the tail deflections and rigid-body motions. The tail-buffet phenomenon is predicted for highly-swept, single vertical tail placed at the plane of geometric symmetry, and for highly-swept, vertical twin tails placed at three different spanwise separation distances. The investigation demonstrates the effects of structural inertial coupling and uncoupling of the bending and torsion modes of vibration, spanwise positions of the twin-tail, angle of attack, and pitching and rolling dynamic motions of the configuration model on the tail buffet loading and response. The fundamental issue of twin-tail buffet alleviation is addressed using two active flow-control methods. These methods are the tangential leading-edge blowing and the flow suction from the leading-edge vortex cores along their paths. Qualitative and quantitative comparisons with the available experimental data are presented. The comparisons indicate that the present multidisciplinary aeroelastic analysis tools are robust, accurate and efficient.

Kandil, Osama A.↗
NASA NTRS2003

Flutter Calculations for an Experimental Fan

During testing, an experimental forward-swept fan encountered flutter at part-speed conditions. A three-dimensional propulsion aeroelasticity code, based on a computational fluid dynamics (CFD) approach, was used to model the aeroelastic behavior of this fan. This paper describes the flutter calculations and compares the results to the experimental measurements. Results of sensitivity studies are also presented that show the relative importance of different aspects of aeroelastic modeling.

Bakhle, Milind A.↗
NASA NTRS2004

Variable Stiffness Spar Wind-Tunnel Model Development and Testing

The concept of exploiting wing flexibility to improve aerodynamic performance was investigated in the wind tunnel by employing multiple control surfaces and by varying wing structural stiffness via a Variable Stiffness Spar (VSS) mechanism. High design loads compromised the VSS effectiveness because the aerodynamic wind-tunnel model was much stiffer than desired in order to meet the strength requirements. Results from tests of the model include stiffness and modal data, model deformation data, aerodynamic loads, static control surface derivatives, and fuselage standoff pressure data. Effects of the VSS on the stiffness and modal characteristics, lift curve slope, and control surface effectiveness are discussed. The VSS had the most effect on the rolling moment generated by the leading-edge outboard flap at subsonic speeds. The effects of the VSS for the other control surfaces and speed regimes were less. The difficulties encountered and the ability of the VSS to alter the aeroelastic characteristics of the wing emphasize the need for the development of improved design and construction methods for static aeroelastic models. The data collected and presented is valuable in terms of understanding static aeroelastic wind-tunnel model development.

Florance, James R.↗
NASA NTRS1997

Multi-Body Analysis of a Tiltrotor Configuration

The paper describes the aeroelastic analysis of a tiltrotor configuration. The 1/5 scale wind tunnel semispan model of the V-22 tiltrotor aircraft is considered. The analysis is performed by means of a multi-body code, based on an original formulation. The differential equilibrium problem is stated in terms of first order differential equations. The equilibrium equations of every rigid body are written, together with the definitions of the momenta. The bodies are connected by kinematic constraints, applied in form of Lagrangian multipliers. Deformable components are mainly modelled by means of beam elements, based on an original finite volume formulation. Multi-disciplinar problems can be solved by adding user-defined differential equations. In the presented analysis the equations related to the control of the swash-plate of the model are considered. Advantages of a multi-body aeroelastic code over existing comprehensive rotorcraft codes include the exact modelling of the kinematics of the hub, the detailed modelling of the flexibility of critical hub components, and the possibility to simulate steady flight conditions as well as wind-up and maneuvers. The simulations described in the paper include: 1) the analysis of the aeroelastic stability, with particular regard to the proprotor/pylon instability that is peculiar to tiltrotors, 2) the determination of the dynamic behavior of the system and of the loads due to typical maneuvers, with particular regard to the conversion from helicopter to airplane mode, and 3) the stress evaluation in critical components, such as the pitch links and the conversion downstop spring.

Ghiringhelli, G. L.↗
NASA NTRS2004

Validation of Design and Analysis Techniques of Tailored Composite Structures

Aeroelasticity is the relationship between the elasticity of an aircraft structure and its aerodynamics. This relationship can cause instabilities such as flutter in a wing. Engineers have long studied aeroelasticity to ensure such instabilities do not become a problem within normal operating conditions. In recent decades structural tailoring has been used to take advantage of aeroelasticity. It is possible to tailor an aircraft structure to respond favorably to multiple different flight regimes such as takeoff, landing, cruise, 2-g pull up, etc. Structures can be designed so that these responses provide an aerodynamic advantage. This research investigates the ability to design and analyze tailored structures made from filamentary composites. Specifically the accuracy of tailored composite analysis must be verified if this design technique is to become feasible. To pursue this idea, a validation experiment has been performed on a small-scale filamentary composite wing box. The box is tailored such that its cover panels induce a global bend-twist coupling under an applied load. Two types of analysis were chosen for the experiment. The first is a closed form analysis based on a theoretical model of a single cell tailored box beam and the second is a finite element analysis. The predicted results are compared with the measured data to validate the analyses. The comparison of results show that the finite element analysis is capable of predicting displacements and strains to within 10% on the small-scale structure. The closed form code is consistently able to predict the wing box bending to 25% of the measured value. This error is expected due to simplifying assumptions in the closed form analysis. Differences between the closed form code representation and the wing box specimen caused large errors in the twist prediction. The closed form analysis prediction of twist has not been validated from this test.

Jegley, Dawn C.↗
NASA NTRS2005

Deflection-Based Aircraft Structural Loads Estimation with Comparison to Flight

Traditional techniques in structural load measurement entail the correlation of a known load with strain-gage output from the individual components of a structure or machine. The use of strain gages has proved successful and is considered the standard approach for load measurement. However, remotely measuring aerodynamic loads using deflection measurement systems to determine aeroelastic deformation as a substitute to strain gages may yield lower testing costs while improving aircraft performance through reduced instrumentation weight. With a reliable strain and structural deformation measurement system this technique was examined. The objective of this study was to explore the utility of a deflection-based load estimation, using the active aeroelastic wing F/A-18 aircraft. Calibration data from ground tests performed on the aircraft were used to derive left wing-root and wing-fold bending-moment and torque load equations based on strain gages, however, for this study, point deflections were used to derive deflection-based load equations. Comparisons between the strain-gage and deflection-based methods are presented. Flight data from the phase-1 active aeroelastic wing flight program were used to validate the deflection-based load estimation method. Flight validation revealed a strong bending-moment correlation and slightly weaker torque correlation. Development of current techniques, and future studies are discussed.

Lizotte, Andrew M.↗
NASA NTRS2006

Impact of Aerodynamics and Structures Technology on Heavy Lift Tiltrotors

Rotor performance and aeroelastic stability are presented for a 124,000-lb Large Civil Tilt Rotor (LCTR) design. It was designed to carry 120 passengers for 1200 nm, with performance of 350 knots at 30,000 ft altitude. Design features include a low-mounted wing and hingeless rotors, with a very low cruise tip speed of 350 ft/sec. The rotor and wing design processes are described, including rotor optimization methods and wing/rotor aeroelastic stability analyses. New rotor airfoils were designed specifically for the LCTR; the resulting performance improvements are compared to current technology airfoils. Twist, taper and precone optimization are presented, along with the effects of blade flexibility on performance. A new wing airfoil was designed and a composite structure was developed to meet the wing load requirements for certification. Predictions of aeroelastic stability are presented for the optimized rotor and wing, along with summaries of the effects of rotor design parameters on stability.

Acree, C. W., Jr.↗
NASA NTRS2009

Fan Flutter Computations Using the Harmonic Balance Method

An experimental forward-swept fan encountered flutter at part-speed conditions during wind tunnel testing. A new propulsion aeroelasticity code, based on a computational fluid dynamics (CFD) approach, was used to model the aeroelastic behavior of this fan. This threedimensional code models the unsteady flowfield due to blade vibrations using a harmonic balance method to solve the Navier-Stokes equations. This paper describes the flutter calculations and compares the results to experimental measurements and previous results from a time-accurate propulsion aeroelasticity code.

Bakhle, Milind A.↗