Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transient Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

A method for analyzing dynamic stall of helicopter rotor blades

A model for each of the basic flow elements involved in the unsteady stall of a two-dimensional airfoil in incompressible flow is presented. The interaction of these elements is analyzed using a digital computer. Computations of the loading during transient and sinusoidal pitching motions are in good qualitative agreement with measured loads. The method was used to confirm that large torsional response of helicopter blades detected in flight tests can be attributed to dynamic stall.

Crimi, P.↗

Determination of flow areas for series-parallel compartment venting to satisfy pressure differential requirements.

A unique method for solving the design problem of determining the areas required to meet an imposed pressure differential limit is presented. The associated analytical technique for determining the transient pressure differentials in a multicompartment series-parallel connected system is also presented. In an effort to verify the results obtained by using the analytical methods presented, a test was conducted using a seven compartment system. It was found in the investigations that a computer program based on the analytical model described can determine the pressure, temperature, pressure differentials, and mass flow rates into and out of each compartment at subsonic or sonic velocities.

Kirby, C. E.↗

The estimation of decay coefficient in pulsed transient data

The problem of estimation and interpretation of a decay coefficient in a pulsed transient signal is considered. Two methods are proposed in estimating the decay coefficient of pulsed decay transient data. The methods are derived through a spectral analysis for a parametric model of impulse response function of signal frequency. The several pulsed response data from T burner tests as well as some synthesized data are analyzed and the performance of the estimation procedures are examined. Suggestions for further research in this area are offered. The estimation procedures presented can be extended to the case of multiple frequencies in pulse response function and time dependent decay or growth coefficients.

Park, T. W.↗

Acurex Parabolic Dish Concentrator (PDC-2)

The design approach, rationale for the selected configuration, and the development status of a cost effective point-focus solar concentrator are discussed. The low-cost concentrator reflective surface design is based on the use of a thin, backsilvered mirror glass reflector bonded to a molded structural plastic substrate. The foundation, support, and drive subassembles are described. A hybrid, two-axis, Sun tracking control system based on microprocessor technology was selected. Coarse synthetic tracking is achieved through a microcomputer-based control system to calculate Sun position for transient periods of cloud cover as well as sundown and sunrise positioning. Accurate active tracking is achieved by two-axis optical sensors. Results of the reflective panel demonstration tests investigating slope error, hail impact survivability, temperature/humidity cycling, longitudinal strength/bending stiffness, and torsional stiffness are discussed.

Overly, P.↗

Identification of nonlinear system parameters in joints using the force-state mapping technique

A procedure is presented for identifying the potentially strong nonlinear properties of structural members, such as joints, by expressing the force transmitted by the member as a function of its mechanical state. By explicitly including position and rate dependent effects, the surface of transmitted force versus state, the force-state map, has distinct, unique, superposable features for common structural nonlinearities, even those which appear to indicate hysteresis on a force-stroke presentation. An analysis is performed on the influence of true memory effects, transient response, and uncertainty in the measurements and system mass on the precision of the procedure. The successful identification of simulated data verifies the accuracy of the identification algorithm. Tests are then conducted on three actual joint models, with incomplete state measurements typical of an actual testing environment. The ability of the procedure to estimate the complete state vector and to analyze and reconstruct the measured nonlinear characteristics is demonstrated.

Crawley, E. F.↗

Universal limiter for transient interpolation modeling of the advective transport equations: The ULTIMATE conservative difference scheme

A fresh approach is taken to the embarrassingly difficult problem of adequately modeling simple pure advection. An explicit conservative control-volume formation makes use of a universal limiter for transient interpolation modeling of the advective transport equations. This ULTIMATE conservative difference scheme is applied to unsteady, one-dimensional scalar pure advection at constant velocity, using three critical test profiles: an isolated sine-squared wave, a discontinuous step, and a semi-ellipse. The goal, of course, is to devise a single robust scheme which achieves sharp monotonic resolution of the step without corrupting the other profiles. The semi-ellipse is particularly challenging because of its combination of sudden and gradual changes in gradient. The ULTIMATE strategy can be applied to explicit conservation schemes of any order of accuracy. Second-order schemes are unsatisfactory, showing steepening and clipping typical of currently popular so-called high resolution shock-capturing of TVD schemes. The ULTIMATE third-order upwind scheme is highly satisfactory for most flows of practical importance. Higher order methods give predictably better step resolution, although even-order schemes generate a (monotonic) waviness in the difficult semi-ellipse simulation. Little is to be gained above ULTIMATE fifth-order upwinding which gives results close to the ultimate for which one might hope.

Leonard, B. P.↗

A PC-based collapse factor analysis for high pressure cryogenic systems

A collapse factor simulation computer program, suitable for use on personal computers, for supercritical cryogen system pressurization is examined. The available literature is previewed, individual component models are developed, and the overall simulation program logic is examined. Extensive use is made of existing thermodynamic and transport property evaluation packages. Heat transfer is estimated using natural convection correlations, and transient wall heat conduction is considered. Examples of the simulation are demonstrated for two facilities. Partial validation is achieved by comparing the simulation output with data from an existing test facility. Preliminary results indicate that the collapse factors will seldom exceed 1.15 during supercritical operation of high-pressure cryogenic systems. Recommendations for improvements in the component models and the simulation are made.

Hodge, B. K.↗

Transient Torque Technique for Viscosity and Electrical Conductivity Determination of Semiconducting Liquids

A novel apparatus based on transient torque technique is constructed in MSFC/NASA. The apparatus uses a 125um diameter quartz fiber as torsion wire. A high sensitive angular detector is implemented to measure the deflection angle of the crucible containing the liquid. A rotating magnetic field (RMF) is used to induce a rotating flow of a conducting or semiconducting melts. By measuring the magnitude and transient behavior of the induced deflection angle, the electrical conductivity and viscosity of the melt can be measured simultaneously. High purity elements namely Hg, Ga, Zn and Te are tested at room temperature and high temperature up to 900 C.

Li, C.↗

Design Strategy for a Formally Verified Reliable Computing Platform

This paper presents a high-level design for a reliable computing platform for real-time control applications. The design tradeoffs and analyses related to the development of a formally verified reliable computing platform are discussed. The design strategy advocated in this paper requires the use of techniques that can be completely characterized mathematically as opposed to more powerful or more flexible algorithms whose performance properties can only be analyzed by simulation and testing. The need for accurate reliability models that can be related to the behavior models is also stressed. Tradeoffs between reliability and voting complexity are explored. In particular, the transient recovery properties of the system are found to be fundamental to both the reliability analysis as well as the "correctness" models.

Butler, Ricky W.↗

Prognostics for Electronics Components of Avionics Systems

Electronics components have and increasingly critical role in avionics systems and for the development of future aircraft systems. Prognostics of such components is becoming a very important research filed as a result of the need to provide aircraft systems with system level health management. This paper reports on a prognostics application for electronics components of avionics systems, in particular, its application to the Isolated Gate Bipolar Transistor (IGBT). The remaining useful life prediction for the IGBT is based on the particle filter framework, leveraging data from an accelerated aging tests on IGBTs. The accelerated aging test provided thermal-electrical overstress by applying thermal cycling to the device. In-situ state monitoring, including measurements of the steady-state voltages and currents, electrical transients, and thermal transients are recorded and used as potential precursors of failure.

Celaya, Jose R.↗

Towards Prognostics for Electronics Components

Electronics components have an increasingly critical role in avionics systems and in the development of future aircraft systems. Prognostics of such components is becoming a very important research field as a result of the need to provide aircraft systems with system level health management information. This paper focuses on a prognostics application for electronics components within avionics systems, and in particular its application to an Isolated Gate Bipolar Transistor (IGBT). This application utilizes the remaining useful life prediction, accomplished by employing the particle filter framework, leveraging data from accelerated aging tests on IGBTs. These tests induced thermal-electrical overstresses by applying thermal cycling to the IGBT devices. In-situ state monitoring, including measurements of steady-state voltages and currents, electrical transients, and thermal transients are recorded and used as potential precursors of failure.

Saha, Bhaskar↗

Development of Buffet Forcing Functions for a Transonic Condition Exhibiting Bimodal Flow Behavior

A wind-tunnel test campaign was used to derive Buffet Forcing Functions (BFFs) of the Space Launch System Block 1B vehicle configuration by measuring and integrating unsteady surface pressures on a 3-percent scale rigid buffet model (RBM) tested at the NASA Langley Transonic Dynamics Tunnel. The model was tested at predetermined and repeatable pitch and side-slip angles and flow Mach numbers encompassing a full range of possible flight conditions. Although each data point was collected at a steady wind-tunnel condition, a transient, bimodal flow behavior was observed in some Mach 1.10 measurements. The pressure time series was alternating between two states, which differed either in mean or fluctuation amplitude values, or both. As a consequence of this behavior, segments of the resultant BFFs can differ based on the duration that each measurement spends in a particular state. In this paper, a methodology is proposed, which envelopes the range of BFFs magnitudes resulting from this random bimodal phenomenon in pressure time histories of certain sensors.

wind-tunnel testing↗

Steady-state and transitional aerodynamic characteristics of a wing in simulated heavy rain

The steady-state and transient effects of simulated heavy rain on the subsonic aerodynamic characteristics of a wing model were determined in the Langley 14- by 22-Foot Subsonic Tunnel. The 1.29 foot chord wing was comprised of a NACA 23015 airfoil and had an aspect ratio of 6.10. Data were obtained while test variables of liquid water content, angle of attack, and trailing edge flap angle were parametrically varied at dynamic pressures of 10, 30, and 50 psf (i.e., Reynolds numbers of .76x10(6), 1.31x10(6), and 1.69x10(6)). The experimental results showed reductions in lift and increases in drag when in the simulated rain environment. Accompanying this was a reduction of the stall angle of attack by approximately 4 deg. The transient aerodynamic performance during transition from dry to wet steady-state conditions varied between a linear and a nonlinear transition.

Campbell, Bryan A.↗

Development of Buffet Forcing Functions for a Transonic Condition Exhibiting Bimodal Flow Behavior

A wind-tunnel test campaign was used to derive Buffet Forcing Functions (BFFs) of the Space Launch System Block 1B vehicle configuration by measuring and integrating unsteady surface pressures on a 3-percent scale rigid buffet model (RBM) tested at the NASA Langley Transonic Dynamics Tunnel. The model was tested at predetermined and repeatable pitch and side-slip angles and flow Mach numbers encompassing a full range of possible flight conditions. Although each data point was collected at a steady wind-tunnel condition, a transient, bimodal flow behavior was observed in some Mach 1.10 measurements. The pressure time series was alternating between two states, which differed either in mean or fluctuation amplitude values, or both. As a consequence of this behavior, segments of the resultant BFFs can differ based on the duration that each measurement spends in a particular state. In this paper, a methodology is proposed, which envelopes the range of BFFs magnitudes resulting from this random bimodal phenomenon in pressure time histories of certain sensors.

wind-tunnel testing↗

Data-Driven Method for Nonlinear Modal Interaction Identification in Fighter Aircraft

The purpose of this paper is to report a new data-driven analysis methodology for identifying nonlinear modal interactions and its application to aeroelastic wind-tunnel data from a generic fighter configuration, which reveals global modal interactions in this system caused by multiple resonance capture events initiated by local nonlinearities. It is shown that during supersonic testing at the Transonic Dynamics Tunnel, vibro-impacts at the embedded external fuel tank shakers on the inboard underwing stations of the generic fighter introduce strong nonlinearity that gives rise to nonlinear modal interactions. Specifically, time–frequency analysis of the acceleration data demonstrates that 6∶5 and 7∶6 transient resonance captures occur across the aircraft exclusively during this vibro-impact forcing window. Further analysis suggests that these resonance captures are dependent on Mach number. These results show experimentally that local vibro-impacts can cause global nonlinear effects in an aeroelastic system and that these effects can be identified using the new methodology herein. The data-driven analysis scheme employed shows applicability to full-aircraft flight test data for identifying nonlinear modal interactions without knowledge of the precise nonlinear contributors.

nonlinear dynamics↗

Compact Simultaneous-beam Optical Strain Measurement System, Phase 5

Recent advances on the laser speckle strain measurement system under development at NASA Lewis Research Center have resulted in a compact, easy-to-use measurement package having many performance improvements over previous systems. NASA has developed this high performance optical strain measurement system for high temperature material testing applications. The system is based on I. Yamaguchi's two-beam speckle-shift strain measurement theory, and uses a new optical design that allows simultaneous recording of laser speckle patterns. This design greatly improves system response over previous implementations of the two-beam speckle-shift technique. The degree of immunity to transient rigid body motions is no longer dependent on the data transfer rate. The system automatically calculates surface strains at a frequency of about 5 Hz using a high speed digital signal processor in a personal computer. This system is fully automated, and can be operated remotely. This report describes the designs and methods used by the system, and shows low temperature strain test results obtained from small diameter tungsten-rhenium and palladium-chrome wires.

Lant, Christian T.↗

Flight motor set 360L001 (STS-26R). (Reconstructed dynamic loads analysis)

A transient analysis was performed to correlate the predicted versus measured behavior of the Redesigned Solid Rocket Booster (RSRB) during Flight 360L001 (STS-26R) liftoff. Approximately 9 accelerometers, 152 strain gages, and 104 girth gages were bonded to the motors during this event. Prior to Flight 360L001, a finite element model of the RSRB was analyzed to predict the accelerations, strains, and displacements measured by this developmental flight instrumentation (DFI) within an order of magnitude. Subsequently, an analysis has been performed which uses actual Flight 360L001 liftoff loading conditions, and makes more precise predictions for the RSRB structural behavior. Essential information describing the analytical model, analytical techniques used, correlation of the predicted versus measured RSRB behavior, and conclusions, are presented. A detailed model of the RSRB was developed and correlated for use in analyzing the motor behavior during liftoff loading conditions. This finite element model, referred to as the RSRB global model, uses super-element techniques to model all components of the RSRB. The objective of the RSRB global model is to accurately predict deflections and gap openings in the field joints to an accuracy of approximately 0.001 inch. The model of the field joint component was correlated to Referee and Joint Environment Simulation (JES) tests. The accuracy of the assembled RSRB global model was validated by correlation to static-fire tests such DM-8, DM-9, QM-7, and QM-8. This validated RSRB global model was used to predict RSRB structural behavior and joint gap opening during Flight 360L001 liftoff. The results of a transient analysis of the RSRB global model with imposed liftoff loading conditions are presented. Rockwell used many gage measurements to reconstruct the load parameters which were imposed on the RSRB during the Flight 360L001 liftoff. Each load parameter, and its application, is described. Also presented are conclusions and recommendations based on the analysis of this load case and the resulting correlation between predicted and measured RSRB structural behavior.

Call, V. B.↗

Thermal Cycle and Capacitance Testing of Mezzo Industries Phase Changer Material Heat Capacitor

Effective Thermal management is essential for the safety and performance of human spacecraft, especially during long-duration missions with fluctuating heat loads. Phase Change Material (PCM) heat exchangers offer a compact, efficient solution by storing and releasing thermal energy through latent heat during phase transitions. This allows PCM systems to buffer transient thermal loads without immediate heat rejection, reducing the need for oversized radiators – particularly critical during ascent and re-entry when radiators are stowed. By maintaining stable temperatures in crew cabins and equipment bays, PCM technology enhances crew comfort, protects sensitive systems, and supports long-term mission sustainability with minimal mass and volume impact. A phase change material heat capacitor prototype, designed and built under a NASA Small Business Innovation Research grant by Mezzo Technologies, utilizes a laser welding microtube manufacturing process that promises increased reliability and performance over current manufacturing methods like brazing. This heat exchanger was tested through coolant thermal cycling within the expected flow rates and temperature range of the Orion spacecraft, the crewed spacecraft taking NASA astronauts to the moon under the Artemis Program. The useful heat storage capacitance was measured and compared to Orion spacecraft requirements.

Active Thermal Control Systems↗