Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Nonmodal Growth of TravelingWaves on Blunt Cones at Hypersonic Speeds

The existing database of transition measurements in hypersonic ground facilities has established that, as the nosetip bluntness is increased, the onset of boundary layer transition over a circular cone at zero angle of attack shifts downstream. However, this trend is reversed at sufficiently large values of the nose Reynolds number, so that the transition onset location eventually moves upstream with a further increase in nose-tip bluntness. Because modal amplification is too weak to initiate transition at moderate-to-large bluntness values, nonmodal growth has been investigated as the potential basis for a physics-based model for the frustum transition. The present analysis investigates the nonmodal growth of traveling disturbances initiated within the nose-tip vicinity that peak within the entropy layer. Results show that, with increasing nose bluntness, both planar and oblique traveling disturbances experience appreciable energy amplification up to successively higher frequencies. For moderately blunt cones, the initial nonmmodal growth is followed by a partial decay that is more than overcome by an eventual, modal growth as Mack-mode waves. For larger bluntness values, the Mack-mode waves are not amplified anywhere upstream of the experimentally measured transition location, but the traveling modes still undergo a significant amount of nonmodal growth. This finding does not provide a definitive link between optimal growth and the onset of transition, but it is qualitatively consistent with the experimental observations that frustum transition in the absence of sufficient Mack-mode amplification implies a double peak in disturbance amplification and the appearance of transitional events above the boundary-layer edge.

Hypersonic speed↗

Prediction of HiMAT RPRV component interference effects at transonic speeds

Detailed surface flow field analyses of the NASA Highly Maneuverable Aircraft Technology Remotely Piloted Research Vehicle (HiMAT RPRV) are described. Computational predictions are provided by a nonlinear finite difference transonic wing-body code. Component interference effects are obtained through modifications in lifting surface twist and camber boundary conditions. Complex aircraft interactions created by wing-tip fins, landing gear, and lower surface wing actuator fairings are included. Lifting surface viscous flow effects are modeled using a two-dimensional 'strip' boundary layer method. Correlations with flight test data presented demonstrate the high degree of accuracy achieved for this realistic aircraft configuration. This methodology and approach appears to be generally applicable to other multisurface configurations.

Laiosa, J.↗

DRAG CHARACTERISTICS AND DYNAMIC STABILITY IN DESCENT OF A ROTARY PARACHUTE TESTED IN A VERTICAL TUNNEL

An investigation was conducted in the Langley 20-foot free-spinning tunnel at low speeds to determine the drag characteristics and dynamic stability in descent of a 64-inch-diameter rotary parachute. The drag coefficient of the basic rotary parachute was approximately 1.7 based on total cloth area_ cutting cloth away from the tips of the parachute permitted it to rotate faster and gave a somewhat higher drag coefficient of about 2.1. In general, the rotary parachute was extremely stable in descent, with oscillations of probably less than 1°. Small changes in rigging had no appreciable effect on the performance of the parachute. Accompanying zip folder contains video of the experimental process completed for this document and the related records for the Experimental aerodynamic performance characteristics of a rotor entry vehicle configuration. 1-3.

WIND TUNNEL↗

Isolated rotor noise due to inlet distortion or turbulence

Theoretical formulation, analysis, and results are presented that are necessary to analyze quadrupole noise generated from a loaded, subsonic rotor because of its interaction with an inflow distortion or inlet turbulence. The ratio of quadrupole to dipole noise is largely a function of the axial Mach number, wheel tip Mach number, rotor solidity, and total pressure ratio across the rotor. It is relatively independent of the specific form of the inflow distortion or inlet turbulence. Comparisons with experimental data only succeed in predicting gross levels at a given speed and fail to predict the variation of noise at fixed speed with flow and pressure ratio. Likely sources of this discrepancy are discussed.

Mani, R.↗

Measurement of Aircraft Speed and Altitude

Problems involved in measuring speed and altitude with pressure-actuated instruments (altimeter, airspeed indicator, true-airspeed indicator, Machmeter, and vertical-speed indicator) are examined. Equations relating total pressure and static pressure to the five flight quantities are presented, and criteria for the design of total and static pressure tubes are given. Calibrations of typical static pressure installations (fuselage nose, wing tip, vertical fin, and fuselage vent) are presented, various methods for flight calibration of these installations are described, and the calibration of a particular installation by two of the methods is described in detail. Equations are given for estimating the effects of pressure lag and leaks. Test procedures for the laboratory calibration of the five instruments are described, and accuracies of mechanical and electrical instruments are presented. Operational use of the altimeter for terrain clearance and vertical separation of aircraft is discussed, along with flight technical errors and overall altitude errors of aircraft in cruise operations. Altitude-measuring techniques based on a variety of properties of the Earth and the atmosphere are included. Two appendixes present airspeed and altitude tables and sample calculations for determining the various flight parameters from measured total and static pressures.

Gracey, W.↗

A holographic interferometry technique for measuring transonic flow near a rotor blade

A technique that uses holographic interferometry to record the first interferograms of the flow near a hovering transonic rotor blade is presented. A pulsed ruby laser is used to record interferograms of a 2 ft diam field of view near a rotor tip operating at a tip Mach number of 0.90. Several interferograms, recorded along planes perpendicular to the rotor's tip path plane at various azimuth angles around the flow, are presented. These interferograms yield quantitative information about shock structure and location, flow separation, and radiated noise that will help helicopter researchers understand the complexities of the flow around high speed rotor blades and thus improve performance and reduce noise.

Kittleson, J. K.↗

A model propulsion simulator for evaluating counter rotating blade characteristics

Three Model Propulsion Simulators (MPS) were designed and built to evaluate candidate counterrotation Ultra bypass fan model blade designs of nominally 2-ft (0.61 m) tip diameter for an advanced 'pusher-type' aircraft engine. These propulsion simulators (nominally 1/5 engine size) are capable of operation over a wide range of subsonic conditions and can deliver up to 750 shaft horsepower per rotor at rotor speeds of 10,000 rpm. The rotor thrust and torque, dynamic blade stresses, and system temperature data are transmitted through an integral telemetry system to facilitate data acquisition. Salient features of the design, instrumentation, and operation of these simulators are described in this paper.

Delaney, B. R.↗

Blade tip rubbing stress prediction

A linear analysis was performed to determine the dynamic response of a turbine blade to intermittent rubbing against a tip seal. The response analysis consisted of a parametric study where the rubbing friction force was assumed to vary as a half sine wave over a preselected contact arc. The length of the contact arc, as well as the pump speed, was varied to determine the effects of each. Results show that for a given contact arc there are distinct critical speeds at which the blade response becomes a maximum.

Brusher, Gerald A.↗

Application of Synthetic Jets to Reduce Stator Flow Separation in a Low Speed Axial Compressor

Flow control using synthetic jet injection has been applied in a low speed axial compressor. The synthetic jets were applied from the suction surface of a stator vane via a span-wise row of slots pitched in the streamwise direction. Actuation was provided externally from acoustic drivers coupled to the vane tip via flexible tubing. The acoustic resonance characteristics of the system, and the resultant jet velocities were obtained. The effects on the separated flow field for various jet velocities and frequencies were explored. Total pressure loss reductions across the vane passage were measured. The effect of synthetic jet injection was shown to be comparable to that of pulsatory injection with mass addition for stator vanes which had separated flow. While only a weak dependence of the beneficial effect was noted based on the excitation frequency, a strong dependence on the amplitude was observed at all frequencies.

Braunscheidel, Edward P.↗

Microgravity Flammability of PMMA Rods in Concurrent Flow

Microgravity experiments burning cast PMMA cylindrical rods in axial flow have been conducted aboard the International Space Station in the Microgravity Science Glovebox (MSG) facility using the Burning and Suppression of Solids (BASS) flow duct, as part of the BASS-II experiment. Twenty-four concurrent-flow tests were performed, focusing on finding flammability limits as a function of oxygen and flow speed. The oxygen was varied by using gaseous nitrogen to vitiate the working volume of the MSG. The speed of the flow parallel to the rod was varied using a fan at the entrance to the duct. Both blowoff and quenching limits were obtained at several oxygen concentrations. Each experiment ignited the rod at the initially hemispherical stagnation tip of the rod, and allowed the flame to develop and heat the rod at a sufficient flow to sustain burning. For blowoff limit tests, the astronaut quickly turned up the flow to obtain extinction. Complementary 5.18-second Zero Gravity Facility drop tests were conducted to compare blowoff limits in short and long duration microgravity. For quenching tests, the flow was incrementally turned down and the flame allowed to stabilize at the new flow condition for at least the solid-phase response time before changing it again. Quenching was observed when the flow became sufficiently weak that the flame could no longer provide adequate heat flux to compensate for the heat losses (conduction into the rod and radiation). A surface energy balance is presented that shows the surface radiative loss exceeds the conductive loss into the rod near the limit. The flammability boundary is shown to represent a critical Damkohler number, expressed in terms of the reaction rate divided by the stretch rate. For the blowoff branch, the boundary exhibits a linear dependence on oxygen concentration and stretch rate, indicating that the temperature at blowoff must be fairly constant. For the quenching branch, the dominance of the exponential nature of the Arrhenius kinetics reaction rate indicates that the temperature is critical.

flammability↗

Compressible 2D Flow Field Interaction of Two Contra-Rotating Blades

The blades of coaxial, contra-rotating rotor systems cross each other in close proximity and at high relative speeds. This crossing event is a potential source of noise and severe blade loads. Effects of compressibility can aggravate the interaction and significantly alter the pressure field signature and phase relationships. A 2-D analysis of this phenomenon is performed by simulating two airfoils passing each other at specified speeds and vertical separation distances. Several test cases spanning a relevant range of Reynolds numbers, angles of attack, and relative Mach number are considered. The Mach number is varied to simulate the radial variation of velocity from the root to tip of a rotor blade to capture the pressure signature, lift, and drag of the airfoils. The velocity and pressure distributions on the airfoils, and in the space between the airfoils are computed before, at, and after airfoil crossing. The variations of lift and drag coefficients through the interaction are captured. The upper airfoil experiences an increase in lift followed by a very sharp drop in lift during the interaction. When relative Mach numbers are transonic, the region of interaction is greatly extended, with shock interactions occurring. The results show the complex nature of the aerodynamic and fluid dynamic impulses generated by blade-blade interactions, with implications to aeroelastic loads and aeroacoustic sources.

Barbely, Natasha L.↗

Combined Bluntness and Roughness Effects on Cones at Hypersonic Speeds

This computational study investigates the effects of discrete roughness elements on a blunt cone at zero degrees angle of attack in a Mach 6 flow. Motivation was provided by experiments conducted in the Air Force Research Laboratory Mach 6 High Reynolds Number facility on a 7-degree half-angle cone with a roughness array located at 45 degrees from the apex on two nose tips of different blutness but equivalent roughness Reynolds number. Transition was only affected on the blunter cone, indicating that the transition onset is associated with the combined effects of bluntness and roughness. The present study investigates the 15.24 mm nose radius, 420 azimuthal wavenumber case via Navier-Stokes computations of the laminar base flow and instability analysis. Plane-marching parabolized stability equations (PSE) and inflow-resolvent analysis based on the three-dimensional, harmonic linearized Navier-Stokes equations (HLNSE) are used to calculate the amplification of disturbances along the roughness wake as well as over the roughness nearfield. Results show that the roughness shape can have a great impact on the characteristics of the most amplified wake instabilities. For the experimental configuration with cubic roughness elements of 15 μ m height, the flow is marginally unstable. For prismatic elements of 20 μ m height, the PSE predicts a logarithmic disturbance amplification ratio of N = 5.6 along its wake, but this ratio increases to N = 9.6 when the amplification over the roughness and separation regions is included in the inflow-resolvent analysis.

Boundary-layer transition↗

A detailed investigation of flight buffeting response at subsonic and transonic speeds

The structural response to aerodynamic buffeting during moderate-to-high-g maneuvers was investigated. Dynamic response data measured during a flight loads program were analyzed to obtain power spectra and rms values of response for 19 sensors mounted on the test aircraft. In this paper, peaks in the power spectra of accelerations measured at the wing tips, center of gravity and pilot's seat, and wing vertical shear, bending moment and torsional moments are correlated with natural vibration modes. The amplitudes of response are compared to show effects of angle of attack, sensor type and location, Mach number, and altitude.

Benepe, D. B.↗

Near wake evolution of a tidal stream turbine due to asymmetric sheared turbulent inflow with different integral length scales

Tidal stream turbines deployed at highly energetic open water sites are subjected to sheared inflow in the rotor plane. The inflow shear is expected to cause asymmetric loading on the rotor blades and affect the downstream wake. In the current study, two different turbulent inflow conditions, static-high shear and dynamic shear, were generated via an active-grid turbulence generator. A 1:20 scaled three-bladed horizontal axis tidal turbine model was tested in those conditions. The results were compared to a quasi-laminar case with no imposed turbulence or shear. The results show that the high shear reduces the average performance, with a drop of up to 16% in the optimal power coefficient. Besides, the shear profiles increase torque fluctuations and induce significant differences in wake hydrodynamics between the high-speed (upper) and low-speed (lower) regions. The large integral length scales further enhance the load fluctuations perceived by the rotor but have a negligible effect on the mean wake field quantities and the wake recovery. The lower half region featured a faster breakdown of tip vortex structure and a rapid drop of swirl number, a phenomenon conjectured to be a consequence of the strong turbulence intensities and Reynolds stresses in the lower half region. Furthermore, the sheared turbulent inflow also results in a very intensive energy redistribution process towards large-scale, low-frequency motions, which is important to the downstream turbines.

16 TIDAL AND WAVE POWER↗

Nickel particle–enabled width-controlled growth of bilayer molybdenum disulfide nanoribbons

Transition metal dichalcogenides exhibit a variety of electronic behaviors depending on the number of layers and width. Therefore, developing facile methods for their controllable synthesis is of central importance. We found that nickel nanoparticles promote both heterogeneous nucleation of the first layer of molybdenum disulfide and simultaneously catalyzes homoepitaxial tip growth of a second layer via a vapor-liquid-solid (VLS) mechanism, resulting in bilayer nanoribbons with width controlled by the nanoparticle diameter. Simulations further confirm the VLS growth mechanism toward nanoribbons and its orders of magnitude higher growth speed compared to the conventional noncatalytic growth of flakes. Width-dependent Coulomb blockade oscillation observed in the transfer characteristics of the nanoribbons at temperatures up to 60 K evidences the value of this proposed synthesis strategy for future nanoelectronics.

36 MATERIALS SCIENCE↗

Recent developments in multi-wire fixed abrasive slicing technique (FAST)

Slicing is an important processing step for all technologies based on the use of ingots. A comparison of the economics of three slicing techniques shows that the fixed abrasive slicing technique (FAST) is superior to the internal diameter (ID) and the multiblade slurry (MBS) techniques. Factors affecting contact length are discussed, taking into account kerf width, rocking angle, ingot size, and surface speed. Aspects of blade development are also considered. A high concentration of diamonds on wire has been obtained in wire packs usd for FAST slicing. The material removal rate was found to be directly proportional to the pressure at the diamond tips.

Schmid, F.↗

Flight Investigation of a Roll-stabilized Missile Configuration at Varying Angles of Attack at Mach Numbers Between 0.8 and 1.79

A missile research model was flown at supersonic speed to determine the quality of automatic roll stabilization at varying angles of attack. Aerodynamic rolling and pitching derivatives were determined from the flight record. It was concluded that the combination of the gyro-actuated automatic pilot with wing-tip ailerons provided adequate roll stabilization under conditions encountered in flight.

INSTRUMENTS↗

Cruise noise measurements of a scale model advanced ducted propulsor

A scale model Advanced Ducted Propulsor (ADP) was tested in NASA Lewis Research Center's 8- by 6-Foot Wind Tunnel to obtain acoustic data at cruise conditions. The model, designed and manufactured by Pratt & Whitney Division of United Technologies, was tested with three inlet lengths. The model has 16 rotor blades and 22 stator vanes, which results in a cut-on condition with respect to rotor-stator interaction noise. Comparisons of the noise directivity of the ADP with that of a previously tested high-speed, unducted propeller showed that the ADP peak blade passing tone was about 30 dB below that of the propeller, and therefore, should not present a cabin or enroute noise problem. The maximum blade passing tone first increased with increasing helical tip Mach number, peaked, and then decreased at a higher Mach number. The ADP tests with the shortest inlet showed more noise in the inlet arc than did tests with either of the other two inlet lengths.

Dittmar, James H.↗