Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Strain calculation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Development of a dual strain gage balance system for measuring light loads

A strain-gage-balance (SGB) force-measurement system is described which was designed to meet light-load requirements for an airfoil model tested in the NASA Langley low-turbulence pressure tunnel (LTPT). This system was developed to obtain direct force data needed to verify calculated pressure/force correlations used in previous aerodynamic tests. The three-component force-measurement system was designed so that the SGBs would simultaneously support and measure the following loads: weight of the airfoil (approximately 3.0 lbf); 8.0 lbf of lift; 0.5 lbf of drag; and 16.0 in. lbf of pitching moment. In addition to these design loads, the system was required to withstand 100-percent overload on all three components. The system comprises an airfoil, two SGBs, a thermal flexure, and a mounting plate. The installation of the system in the LTPT is also discussed.

Roberts, Paul W.↗
NASA NTRS1994

Modeling the effect of water on mantle rheology

To study the thermal history of the Earth we use a parameterized model of mantle convection. This model includes a mathematical description of de- and regassing processes of water from the Earth's mantle. The rates of this processes are considered to be directly proportional to the seafloor spreading rate. The kinematic viscosity of the mantle depends on the temperature/pressure as well as on the volatile content. Dissolved volatiles such as water weaken the minerals by reducing their activation energy for solid state creep. Karato and Toriumi showed a power law dependence between creep rate and water fugacity derived from experimental results. Therefore, we use such flow parameters of diffusion creep in olivine under wet and dry conditions to calculate the mantle viscosity as a function of the water content. Because the creep rate is proportional to the concentration of water-related point deflects we assume that the water fugacity is proportional to the water weight fraction. An equation for the steady-state strain rate under wet conditions is established. To assess the unknown constant K in this equation, we use flow law parameters given by Karato and Wu as well as the results of McGovern and Schubert.

Bounama, CH.↗
NASA NTRS2004

Fracture Mechanics Analysis of an Annular Crack in a Three-concentric-cylinder Composite Model

A boundary-value problem governing a three-phase concentric-cylinder model was analytically modeled to analyze annular interfacial crack problems with Love s strain functions in order to find the stress intensity factors (SIFs) and strain energy release rates (SERRs) at the tips of an interface crack in a nonhomogeneous medium. The complex form of a singular integral equation (SIE) of the second kind was formulated using Bessel s functions in the Fourier domain, and the SIF and total SERR were calculated using Jacoby polynomials. For the validity of the SIF equations to be established, the SIE of the three-concentric-cylinder model was reduced to the SIE for a two-concentric-cylinder model, and the results were compared with the previous results of Erdogan. A preliminary set of parametric studies was carried out to show the effect of interphase properties on the SERR. The method presented here provides insight about the effect of interphase properties on the crack driving force.

Kuguoglu, Latife H.↗
DOE OSTI2022

Violation of the rule of parsimony: Mixed local moment and itinerant Fe magnetism in Fe 3 GeN

Ternary iron nitrides are of considerable interest due to their diverse magnetic properties. We find, based on first principles calculations, that the relatively minor structural distortion from the cubic antiperovskite structure in Fe$_3$GeN, consisting of octahedral rotations, leads to unusual magnetic behavior. In particular, there is a separation into Fe sites with very different magnetic behaviors, specifically a site with Fe atoms having a stable local moment and a site where the Fe shows characteristics of much more itinerant behavior. This shows a remarkable flexibility of the Fe magnetic behavior in these nitrides and points towards the possibility of systems where minor structural and chemical changes can lead to dramatic changes in magnetic properties. The results suggest that, analogously to oxide perovskite materials, modulation of magnetic properties via chemical or strain control of octahedral rotation may be feasible. Furthermore, this may then lead to approaches for tuning magnetism to realize properties of interest, for example tuning magnetic transitions to quantum critical regimes or to proximity to metamagnetic transitions of interest for devices.

36 MATERIALS SCIENCE↗
NASA NTRS1984

A comparison of several methods of calculating fracture toughness from composite laminate test data

Critical fracture toughness was determined by two different techniques for graphite/epoxy laminates of three stacking sequences and several thicknesses. Critical fracture toughness was determined by a finite element stress analysis of a center-cracked tension specimen which yielded the stress intensity factor as a function of specimen thickness and applied load. As an alternative approach the critical strain energy release rate was determined from the compliance calibration technique. Test results from both procedures are compared and discussed.

Harris, C. E.↗
DOE OSTI2021

Superconductivity and topological properties of MgB 2 -type diborides from first principles

The superconductivities and topological properties of MgB 2 -type diborides are investigated by means of first-principles calculations with different exchange-correlation functionals. Functionals with the van der Waals (vdW) correction (such as OptB88-vdW) may predict critical temperature (T c ) comparable with experimental results for several MgB 2 -type superconductors, particularly for the pristine MgB 2 (39.3 vs 39 K). Interestingly, the spin-fluctuation is found to play a significant role in the superconducting behavior of diborides with transition metal elements, and their T c can be enhanced monotonically by applying tensile strains. Furthermore, Dirac surface states of Ta B 2 and NbB 2 are revealed, suggesting their potential use as topological superconducting materials. Finally, this paper provides a useful guideline for ab initio studies of superconductivities and topological properties of vdW layered materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2019

Fundamental Improvement of a Convergence Test for Iterative Strain-Gage Balance Load Predictions

A fundamental improvement of a convergence test for wind tunnel strain-gage balance load iterations was developed. The improvement became necessary because incorrect test results were obtained whenever the original test was applied to multi-component balances with large load capacity differences. The original test was first published in NASA TN D-6860. It uses an upper bound of the Lipschitz constant to assess convergence characteristics of balance load predictions whenever the Iterative Method is applied. The Lipschitz constant is a function of the partial derivatives of each balance load component with respect to all other load components. Unfortunately, the original definition of the convergence test overlooked the fact that the Lipschitz constant is a dimensionless quantity and that the partial derivative of one load component with respect to another load component is not always dimensionless. Therefore, an improvement of the original test was successfully developed that uses load capacities to make all inputs for the calculation of the Lipschitz constant dimensionless before use. Results from the calibration data analysis of a six-component force balance and a five-component semi-span balance are used to illustrate the application of the improved load iteration convergence test.

Strain-Gage Balance↗
DOE OSTI2025

Anisotropic structure and optical engineering of strontium titanate and zirconia responding to sequential hydrogen and helium irradiation

Unraveling the correlation between strain engineering with anisotropic optical properties via nanoscale defects gradually evolved into a strategy for fundamental studies and technological applications, yet it remains understudied in functional complex oxides compared to metals and semiconductors. Here, the methodology of strain engineering for the determination of the lattice parameters, parallel/normal to the sample surface, in the individual layers of single-crystalline superlattices is derived, which is based on analysis of high-angle X-ray diffraction measurements in combination with diffraction reciprocal space mapping. With modeling that takes into account the effect of elastic properties, two elastically anisotropic materials, SrTiO 3 and ZrO 2 , have been compared in terms of defect-induced elastic strain caused by individual and sequential H + and He 2+ irradiation. The anisotropic lattice swelling with corresponding refractive index, and obstructive behavior of elastic strain recovery are demonstrated in SrTiO 3 , while approaching strain behaviors accompanied by isotropic refractive index distribution in both orientations are confirmed in ZrO 2 . Under sequential He 2+ /H + irradiation, pre-existing He-vacancy complexes acted as vacancy traps, preferentially capturing H + clusters to induce lattice distortion and enhance absorption. Nanohardness increments (ΔH) calculated by the DBH model matched nanoindentation results, confirming that sequential irradiation generated higher indentation yield stress than individual irradiations.

Anisotropic expansion↗
DOE OSTI2020

The nature and origins of decametre-scale porosity in Ordovician carbonate rocks, Halahatang oilfield, Tarim Basin, China

At >7 km depths in the Tarim Basin, hydrocarbon reservoirs in Ordovician rocks of the Yijianfang Formation contain large cavities ( c . 10 m or more), vugs, fractures and porous fault rocks. Although some Yijianfang Formation outcrops contain shallow (formed near surface) palaeokarst features, cores from the Halahatang oilfield lack penetrative palaeokarst evidence. Outcrop palaeokarst cavities and opening-mode fractures are mostly mineral filled but some show evidence of secondary dissolution and fault rocks are locally highly ( c . 30%) porous. Cores contain textural evidence of repeated formation of dissolution cavities and subsequent filling by cement. Calcite isotopic analyses indicate depths between c . 220 and 2000 m. Correlation of core and image logs shows abundant cement-filled vugs associated with decametre-scale fractured zones with open cavities that host hydrocarbons. A Sm–Nd isochron age of 400 ± 37 Ma for fracture-filling fluorite indicates that cavities in core formed and were partially cemented prior to the Carboniferous, predating Permian oil emplacement. Repeated creation and filling of vugs, timing constraints and the association of vugs with large cavities suggest dissolution related to fractures and faults. In the current high-strain-rate regime, corroborated by velocity gradient tensor analysis of global positioning system (GPS) data, rapid horizontal extension could promote connection of porous and/or solution-enlarged fault rock, fractures and cavities. Supplementary material: Stable isotopic analyses and the velocity gradient tensor and principal direction and magnitude calculation are available at https://doi.org/10.6084/m9.figshare.c.4946046 Thematic collection: This article is part of the The Geology of Fractured Reservoirs collection available at: https://www.lyellcollection.org/cc/the-geology-of-fractured-reservoirs

Geology↗
NASA NTRS1983

Filler bar heating due to stepped tiles in the shuttle orbiter thermal protection system

An analytical study was performed to investigate the excessive heating in the tile to tile gaps of the Shuttle Orbiter Thermal Protection System due to stepped tiles. The excessive heating was evidence by visible discoloration and charring of the filler bar and strain isolation pad that is used in the attachment of tiles to the aluminum substrate. Two tile locations on the Shuttle orbiter were considered, one on the lower surface of the fuselage and one on the lower surface of the wing. The gap heating analysis involved the calculation of external and internal gas pressures and temperatures, internal mass flow rates, and the transient thermal response of the thermal protection system. The results of the analysis are presented for the fuselage and wing location for several step heights. The results of a study to determine the effectiveness of a half height ceramic fiber gap filler in preventing hot gas flow in the tile gaps are also presented.

Petley, D. H.↗
NASA NTRS1985

Source phase shift - A new phenomenon in wave propagation due to anelasticity

The free oscillations of an anelastic earth model due to earthquakes were calculated directly by means of the correspondence principle from wave propagation theory. The formulation made it possible to find the source phase which is not predictable using first order perturbation theory. The predicted source phase was largest for toroidal modes with source components proportional to the radial strain scalar instead of the radial displacement scalar. The source phase increased in relation to the overtone number. In addition, large relative differences were found in the excitation modulus and the phase when the elastic excitation was small. The effect was sufficient to bias estimates of source properties and elastic structure.

Buland, R.↗
NASA NTRS1988

Leg size and muscle functions associated with leg compliance

The relationship between the leg compliance and factors related to the size of leg muscle and to physical fitness was investigated in ten healthy subjects. Vascular compliance of the leg, as determined by a mercury strain gauge, was found to be not significantly correlated with any variables associated with physical fitness per se (e.g., peak O2 uptake, calf strength, age, body weight, or body composition. On the other hand, leg compliance correlated with the calf cross-sectional area (CSA) and the calculated calf volume, with the CSA of calf muscle being the most dominant contributing factor (while fat and bone were poor predicators). It is suggested that leg compliance can be lowered by increasing calf muscle mass, thus providing structural support to limit the expansion of leg veins.

Convertino, Victor A.↗
NASA NTRS2001

Improved Equivalent Linearization Implementations Using Nonlinear Stiffness Evaluation

This report documents two new implementations of equivalent linearization for solving geometrically nonlinear random vibration problems of complicated structures. The implementations are given the acronym ELSTEP, for "Equivalent Linearization using a STiffness Evaluation Procedure." Both implementations of ELSTEP are fundamentally the same in that they use a novel nonlinear stiffness evaluation procedure to numerically compute otherwise inaccessible nonlinear stiffness terms from commercial finite element programs. The commercial finite element program MSC/NASTRAN (NASTRAN) was chosen as the core of ELSTEP. The FORTRAN implementation calculates the nonlinear stiffness terms and performs the equivalent linearization analysis outside of NASTRAN. The Direct Matrix Abstraction Program (DMAP) implementation performs these operations within NASTRAN. Both provide nearly identical results. Within each implementation, two error minimization approaches for the equivalent linearization procedure are available - force and strain energy error minimization. Sample results for a simply supported rectangular plate are included to illustrate the analysis procedure.

Rizzi, Stephen A.↗
NASA NTRS1999

Strain Gauge Balance Uncertainty Analysis at NASA Langley: A Technical Review

This paper describes a method to determine the uncertainties of measured forces and moments from multi-component force balances used in wind tunnel tests. A multivariate regression technique is first employed to estimate the uncertainties of the six balance sensitivities and 156 interaction coefficients derived from established balance calibration procedures. These uncertainties are then employed to calculate the uncertainties of force-moment values computed from observed balance output readings obtained during tests. Confidence and prediction intervals are obtained for each computed force and moment as functions of the actual measurands. Techniques are discussed for separate estimation of balance bias and precision uncertainties.

John S Tripp↗
DOE OSTI2025

Revealing atomic-scale switching pathways in van der Waals ferroelectrics

Two-dimensional (2D) van der Waals (vdW) materials hold the potential for ultrascaled ferroelectric (FE) devices due to their silicon compatibility and robust polarization down to atomic scale. However, the inherently weak vdW interactions enable facile sliding between layers, introducing complexities beyond those encountered in conventional ferroelectric materials and presenting substantial challenges in uncovering intricate switching pathways. Here, we combine atomic-resolution imaging under in situ electrical biasing conditions with first-principles calculations to unravel the atomic-scale switching mechanisms in SnSe, a vdW group IV monochalcogenide. Our results uncover the coexistence of a consecutive 90° switching pathway and a direct 180° switching pathway from antiferroelectric (AFE) to FE order in this vdW system. Atomic-scale investigations and strain analysis reveal that the switching processes simultaneously induce interlayer sliding and compressive strain, while the lattice remains coherent despite the presence of multidomain structures. These findings elucidate vdW ferroelectric switching dynamics at atomic scale and lay the foundation for the rational design of 2D ferroelectric nanodevices.

Li, Xinyan [Rice University, Houston, TX (United S↗
NASA NTRS1987

Heat generation in Aircraft tires under yawed rolling conditions

An analytical model was developed for approximating the internal temperature distribution in an aircraft tire operating under conditions of yawed rolling. The model employs an assembly of elements to represent the tire cross section and treats the heat generated within the tire as a function of the change in strain energy associated with predicted tire flexure. Special contact scrubbing terms are superimposed on the symmetrical free rolling model to account for the slip during yawed rolling. An extensive experimental program was conducted to verify temperatures predicted from the analytical model. Data from this program were compared with calculation over a range of operating conditions, namely, vertical deflection, inflation pressure, yaw angle, and direction of yaw. Generally the analytical model predicted overall trends well and correlated reasonably well with individual measurements at locations throughout the cross section.

Dodge, Richard N.↗
NASA NTRS1988

Stress-and-Strain Analysis Of Hot Metal/Fiber Composites

Macroscopic mechanical properties derived from micromechanics. Stress-and-strain equations developed to express microscopic and macroscopic mechanical properties of metals reinforced by unidirectional fibers, over range of temperatures. New equations reduce computational load by providing approximate, closed-form expressions for microscopic and pseudohomogeneous anisotropic properties of single ply reinforced by unidirectional fibers. Typical application is calculation of residual stress in newly manufactured article.

Hopkins, Dale A.↗
NASA NTRS1990

Fracture-tough, corrosion-resistant bearing steels

The fundamental principles allowing design of stainless bearing steels with enhanced toughness and stress corrosion resistance has involved both investigation of basic phenomena in model alloys and evaluation of a prototype bearing steel based on a conceptual design exercise. Progress in model studies has included a scanning Auger microprobe (SAM) study of the kinetics of interfacial segregation of embrittling impurities which compete with the kinetics of alloy carbide precipitation in secondary hardening steels. These results can define minimum allowable carbide precipitation rates and/or maximum allowable free impurity contents in these ultrahigh strength steels. Characterization of the prototype bearing steel designed to combine precipitated austenite transformation toughening with secondary hardening shows good agreement between predicted and observed solution treatment response including the nature of the high temperature carbides. An approximate equilibrium constraint applied in the preliminary design calculations to maintain a high martensitic temperature proved inadequate, and the solution treated alloy remained fully austenitic down to liquid nitrogen temperature rather than transforming above 200 C. The alloy can be martensitically transformed by cryogenic deformation, and material so processed will be studied further to test predicted carbide and austenite precipitation behavior. A mechanistically-based martensitic kinetic model was developed and parameters are being evaluated from available kinetic data to allow precise control of martensitic temperatures of high alloy steels in future designs. Preliminary calculations incorporating the prototype stability results suggest that the transformation-toughened secondary-hardening martensitic-stainless design concept is still viable, but may require lowering Cr content to 9 wt. pct. and adding 0.5 to 1.0 wt. pct. Al. An alternative design approach based on strain-induced martensitic transformation during cryogenic forming, thus removing the high martensitic constraint, may permit alloy compositions offering higher fracture roughness.

Olson, Gregory B.↗