Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICONES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Heavy doping effects in high efficiency silicon solar cells

The temperature dependence of the emitter saturation current for bipolar devices was studied by varying the surface recombination velocity at the emitter surface. From this dependence, the value was derived for bandgap narrowing that is in better agreement with other determinations that were obtained from the temperature dependence measure on devices with ohmic contacts. Results of the first direct measurement of the minority-carrier transit time in a transparent heavily doped emitter layer were reported. The value was obtained by a high-frequency conductance method recently developed and used for doped Si. Experimental evidence is presented for significantly greater charge storage in highly excited silicon near room temperature than conventional theory would predict. These data are compared with various data for delta E sub G in heavily doped silicon.

Lindholm, F. A.↗
NASA NTRS1986

Dislocation dynamics during the growth of silicon ribbon

The thermal viscoplastic stresses and the dislocation densities in silicon ribbon are computed for an axially changing thermal profile by using an iterative finite difference method. A material constitutive equation (Haasen-Sumino model) which involves an internal variable (mobile dislocation density) is used. The results are interpreted as showing that there is a maximum width of silicon ribbon that can be grown when viscoplasticity and dislocations are considered. This maximum width limitation does not exist if the material behavior is elastic.

Dillon, O. W., Jr.↗
NASA NTRS1986

Further advances in silicon solar cell technology for space application

Recent improvements relating to the design of high efficiency cells are presented. A conceptual design using passivation techniques is discussed, which potentially increases the open circuit voltage to approximately 650 mV. This concept is supported by experimental data using only silicon passivation beneath contacts. The use of thin thermal oxides of silicon for passivation between contacts is also discussed. A number of novel structures have also been fabricated to investigate reduction in the thermal alpha of planar and sculptured cells. It is shown that this may be as low as 0.63 on glassed gridded back cells, and that the IR rejection beyond 1.1 microns may approach 100 percent if the backside is AR coated. Finally, experimental data is given to support the existence of free electron absorption in heavily doped emitters on sculptured cells.

Lillington, D. R.↗
NASA NTRS1986

High-efficiency silicon solar cells - Development, current issues and future directions

This paper provides a review of material, process, and design considerations that are essential for achieving high-efficiency silicon solar cells. It describes an approach that resulted in 18.0-18.5-percent-efficient cells on low-resistivity float-zone silicon material. It is shown experimentally that a combination of surface passivation and double-layer antireflection coating can provide 2-3 percent (absolute) improvement in cell efficiency provided the material, process and cell design are carefully selected.

Rohatgi, A.↗
NASA NTRS1985

Simulation analysis of a novel high efficiency silicon solar cell

It is recognized that crystalline silicon photovoltaic module efficiency of 15 percent or more is required for cost-effective photovoltaic energy utilization. This level of module efficiency requires large-area encapsulated production cell efficiencies in the range of 18 to 20 percent. Though the theoretical maximum of silicon solar cell efficiency for an idealized case is estimated to be around 30 percent, practical performance of cells to-date are considerably below this limit. This is understood to be largely a consequence of minority carrier losses in the bulk as well as at all surfaces including those under the metal contacts. In this paper a novel device design with special features to reduce bulk and surface recombination losses is evaluated using numerical analysis technique. Details of the numerical model, cell design, and analysis results are presented.

Mokashi, Anant R.↗
NASA NTRS1985

Electrochemical degradation of amorphous-silicon photovoltaic modules

Techniques of module electrochemical corrosion research, developed during reliability studies of crystalline-silicon modules (C-Si), have been applied to this new investigation into amorphous-silicon (a-Si) module reliability. Amorphous-Si cells, encapsulated in the polymers polyvinyl butyral (PVB) and ethylene vinyl acetate (EVA), were exposed for more than 1200 hours in a controlled 85 C/85 percent RH environment, with a constant 500 volts applied between the cells and an aluminum frame. Plotting power output reduction versus charge transferred reveals that about 50 percent a-Si cell failures can be expected with the passage of 0.1 to 1.0 Coulomb/cm of cell-frame edge length; this threshold is somewhat less than that determined for C-Si modules.

Mon, G. R.↗
NASA NTRS1987

Silicon radiation detectors with oxide charge state compensation

This paper discusses the use of boron implantation on high resistivity P type silicon before oxide growth to compensate for the presence of charge states in the oxide and oxide/silicon interface. The presence of these charge states on high resistivity P type silicon produces an inversion layer which causes high leakage currents on N(+)P junctions and high surface conductance. Compensating the surface region by boron implantation is shown to result in oxide passivated N(+)P junctions with very low leakage currents and with low surface conductance.

Walton, J. T.↗
NASA NTRS1986

Effects of excitation intensity on the photocurrent response of thin film silicon solar modules

Photocurrent responses of amorphous thin film silicon solar modules at room temperature were studied at different excitation intensities using various monochromatic light sources. Photocurrent imaging techniques have been effectively used to locate rapidly, and non-destructively, failure and defect sites in the multilayer thin film device. Differences observed in the photocurrent response characteristics for two different cells in the same amorphous thin film silicon solar module suggest the possibility of the formation of dissimilarly active devices, even though the module is processed in the same fabrication process. Possible mechanisms are discussed.

Kim, Q.↗
NASA NTRS1987

Analysis of plastic deformation in silicon web crystals

Numerical calculation of 111-plane 110-line slip activity in silicon web crystals generated by thermal stresses is in good agreement with etch pit patterns and X-ray topographic data. The data suggest that stress redistribution effects are small and that a model, similar to that proposed by Penning (1958) and Jordan (1981) but modified to account for dislocation annihilation and egress, can be used to describe plastic flow effects during silicon web growth.

Spitznagel, J. A.↗
NASA NTRS1987

Dislocation dynamics of web type silicon ribbon

Silicon ribbon grown by the dendritic web process passes through a rapidly changing thermal profile in the growth direction. This rapidly changing profile induces stresses which produce changes in the dislocation density in the ribbon. A viscoplastic material response function (Haasen-Sumino model) is used herein to calculate the stresses and the dislocation density at each point in the silicon ribbon. The residual stresses are also calculated.

Dillon, O. W., Jr.↗
NASA NTRS1987

Advancements in silicon web technology

Low defect density silicon web crystals up to 7 cm wide are produced from systems whose thermal environments are designed for low stress conditions using computer techniques. During growth, the average silicon melt temperature, the lateral melt temperature distribution, and the melt level are each controlled by digital closed loop systems to maintain thermal steady state and to minimize the labor content of the process. Web solar cell efficiencies of 17.2 pct AM1 have been obtained in the laboratory while 15 pct efficiencies are common in pilot production.

Hopkins, R. H.↗
NASA NTRS1987

Residual stress measurement in silicon sheet by shadow moire interferometry

A shadow moire interferometry technique has been developed to measure residual strain in thin silicon sheet. The curvature of a segment of sheet undergoing four-point bending is analyzed to include the applied bending moments, the in-plane residual stresses, and the 'end effect' of the sheet since it is of finite length. The technique is applied to obtain residual stress distributions for silicon sheet grown by the edge-defined film-fed growth technique.

Kwon, Y.↗
NASA NTRS1987

Performance improvements in silicon flat-plate cells and modules

This paper reports the development of a flat-plate module based on highly efficient ion-implanted silicon solar cells. The cells developed in this work are 53 sq cm in area and have exhibited AM 1.5 efficiencies of over 18 percent. The use of back surface reflectors to reduce module operating temperature is discussed. A comparison of various approaches to cell design is made, and module test data for these designs are presented. A comparison of float zone and Czochralski silicon is made. Module efficiency of over 15 percent (at 25 C) is reported.

Spitzer, M. B.↗
NASA NTRS1987

Dislocation dynamics and the viscoplastic buckling of dendritic web type silicon ribbon

The effect of dendrites (reinforced edges) on the residual stresses, dislocation densities and buckling behavior during growth of web type silicon ribbon is studied. A viscoplastic material response function (Haasen-Sumino model) is used to calculate the stresses and the disloction density at each point in the silicon ribbon. In addition, the role of dendrites on the viscoplastic buckling behavior of the ribbon is investigated. The critical thicknesses, the corresponding deflection shapes and lateral deflection speeds are calculated. These results are then compared with similar data obtained for flat plates.

Tsai, C. T.↗
NASA NTRS1986

Thermal sensing of cryogenic wind tunnel model surfaces - Evaluation of silicon diodes

Different sensors and installation techniques for surface temperature measurement of cryogenic wind tunnel models were investigated. Silicon diodes were selected for further consideration because of their good inherent accuracy. Their average absolute temperature deviation in comparison tests with standard platinum resistance thermometers was found to be 0.2 K in the range from 125 to 273 K. Subsurface temperature measurement was selected as the installation technique in order to minimize aerodynamic interference. Temperature distortion caused by an embedded silicon diode was studied numerically.

Daryabeigi, Kamran↗
NASA NTRS1988

Growing Wider Silicon Ribbons

New lid design makes larger withdrawal opening feasible. Wider silicon ribbons grown by dendritic-web method with proposed modification of furnace lid. Modification increases by about 22 percent size of portion of lid that limits ribbon width, potentially increasing area of single-crystal silicon ribbon and productivity.

Duncan, C. S.↗
NASA NTRS1988

Sublid Speeds Growth Of Silicon Ribbon

Heat shield permits enhancement of exit cooling without formation of unwanted crystals. Thermal barrier between molten silicon and lid of susceptor and crucible allows solidifying ribbon of silicon to be withdrawn faster. Barrier, or sublid, increases production rate.

Seidensticker, R. G.↗
NASA NTRS1988

Process Makes High-Grade Silicon

Reactants and electrolyte recycled to yield relatively pure product. Process based on reaction of silicon dioxide with aluminum. Aluminum for process taken from operating aluminum-electrolysis cell, and Al2O3 product returned to same cell. Aluminum continually recycled and purified, and purity of silicon high as well.

Keller, Rudolf↗