Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

In-situ Inspection of Reflowable-Interface Composite Joints During Cure in an Autoclave

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination, which can cause weak bonds. Regulatory organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded primary-structures to alleviate the inability to certify bonded performance. To address this issue, the NASA Convergent Aeronautics Solutions (CAS): Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy-matrix resins to enable reflow and diffusion of the resin at the joint interface during a secondary bonding and cure process. The reflow and intermixing of the matrix resin during assembly can eliminate the material discontinuity at the interface, thereby removing the dependence of bond performance on adhesion at a nearly two-dimensional boundary. AERoBOND process development has evaluated a multitude of parameters including the materials used, the stoichiometric offset of the epoxy resins, time and temperature of cure, and thickness of each ply. Without in-situ process monitoring, the condition of a test article is unknown until mechanical testing is completed. This paper describes the use of an in-situ ultrasonic inspection system to monitor the joining of two composite parts assembled using the AERoBOND technique. This work quantifies the interface by measuring the wave reflection, or lack thereof, at the joint throughout the cure cycle. In addition, the results indicate when reflow and cure of the epoxy resin at the joint occurred. By using the recently developed in-situ inspection method with a mobile ultrasonic transducer, localized results can be obtained across a large portion of the joint with high resolution.

Tyler B Hudson↗

Implementation of Ion Exchange Processes on Industrial Waste Streams for CO 2 Mineralization

Economic development and population growth will lead to an increase in global energy consumption. Large coal-fired power plants (>500 MW) account for almost half of the total CO 2 emissions from fossil fuel combustion, and nearly 26% of the global fossil fuel and industry CO 2 emissions. Long-term management of the more than 36 Gt of CO 2 that is emitted globally per year is urgently needed. CO 2 mineralization is an attractive method of sequestering CO 2 because it captures CO 2 as an insoluble carbonate mineral, mimicking the natural process of rock weathering. Here, we present a pathway for accelerated CO 2 mineralization enabled by divalent cations sourced from liquid streams. In this work, we investigate a mineralization route that converts flue gas CO 2 to precipitated calcium carbonate (PCC) using waste aqueous streams as the calcium source. The proposed mineralization route integrates CO 2 utilization and waste liquid management at coal power plants. Maintaining alkalinity during carbonation is the primary challenge in this process. Instead of relying on the consumption of costly and unsustainable sources of alkalinity (e.g., sodium hydroxide), we used regenerable solids to increase the pH of water by ion exchange. The increase in alkalinity creates a more thermodynamically favorable environment for calcite precipitation. The capacities for ion exchange of various commercially available zeolites and ion exchange resins in CO 2 -saturated water were studied through batch equilibrium and column ion-exchange experiments. During ion exchange, H + in the water exchanges with Na + , Ca 2+ or K + in the zeolite or resin. Batch equilibrium isotherms for H + –Na + exchange were collected by first adding varying amounts of the ion exchange solid (0 – 1.0 kg per kg of water) to CO 2 -saturated water (pCO 2 = 1 atm, pH 4) to determine the maximum H + –Na + exchange achievable. Ion-exchange column studies were performed to determine breakthrough capacity of the system. In both systems, an increase in pH coupled with an increase in Na concentration was observed, demonstrating the feasibility of forward ion exchange. Zeolitic materials increased the alkalinity of the solution from pH 4 to around 10, whereas ion exchange resins containing weakly acidic functional groups (e.g., carboxylic acid) exhibited higher affinity for H + , increasing pH to 11.3 and surpassing the pH shift induced by the zeolitic materials. The extent of calcite precipitation was evaluated by mixing the alkaline CO 3 2- -rich water obtained after passing through the ion-exchange column and a CaCl 2 solution. Calcite yields are as expected from chemical thermodynamics. Calcium carbonate yields found experimentally were about 26 and 8 mmol per kg water for the weakly acidic ion exchange resin and zeolitic materials, respectively. The results from these studies indicate that ion exchange processes can be used as an alternative to the addition of stoichiometric inorganic bases (e.g., sodium hydroxide) to induce alkalinity for the consequent precipitation of CaCO 3 . Instead, weakly acidic ion exchange resins commonly used for water hardness removal were alternatively used to induce pH swings in the aqueous solutions. The high calcium carbonate yields obtained for the materials examined demonstrate the potential application of this process. In addition, the successful operation of the calcium carbonate production process at standard temperature and pressure conditions support its potential for industrial implementation.

Simonetti, Dante↗

System and method for computed axial lithography (CAL) for 3D additive manufacturing

A method of forming a three dimensional (3D) object is disclosed. The method may involve providing a volume of photo-curable resin contained within an optically transparent resin container, and simultaneously directing optical projections from an optical subsystem at a plurality of angles θ through the volume of photo-curable resin. The optical beams are directed about a z axis extending through the volume of photo-curable resin. Each of the projections is provided with a calculated 2D spatial intensity function which creates a 3D intensity map. The projections act over a fixed temporal exposure period, during which the net exposure dose is sufficient to cure select portions of the volume of photo-curable resin, and to leave other portions uncured, to form a desired 3D part.

36 MATERIALS SCIENCE↗

Method of solvent-free manufacturing of composite electrodes incorporating radiation curable binders

A method of making an electrode includes the step of mixing active material particles, radiation curable resin precursors, and electrically conductive particles to create an electrode precursor mixture. The electrode precursor mixture is electrostatically sprayed onto a current collector to provide an electrode preform. The electrode preform is heated and calendered to melt the resin precursor such that the resin precursor surrounds the active particles and electrically conductive particles. Radiation is applied to the electrode preform sufficient to cure the radiation curable resin precursors into resin.

25 ENERGY STORAGE↗

Stereolithography additive manufacturing of photoaligned liquid crystal elastomers

A method of forming a three-dimensional structure of liquid crystal (LC) elastomers includes contacting a resin layer of LC oligomers with a layer of photoalignment material, and exposing a portion of photoalignment material to light for aligning the portion of photoalignment material in a first orientation. The LC oligomers adjacent the illuminated portion of photoalignment material align to the first orientation of the illuminated portion. The portion of aligned LC oligomers of the resin layer are cured. Operations for forming additional layers include creating a relative movement of the resin layer away from the photoalignment material, contacting another resin layer with the photoalignment material, and exposing another portion of photoalignment material to light for aligning the photoalignment material in a different orientation. The LC oligomers adjacent the illuminated portion of photoalignment material align to the different orientation, and the portion of aligned LC oligomers of the resin layer are cured.

Moran, Bryan D.↗

Method of solvent-free manufacturing of composite electrodes incorporating radiation curable binders

A method of making an electrode includes the step of mixing active material particles, radiation curable resin precursors, and electrically conductive particles to create an electrode precursor mixture. The electrode precursor mixture is electrostatically sprayed onto a current collector to provide an electrode preform. The electrode preform is heated and calendered to melt the resin precursor such that the resin precursor surrounds the active particles and electrically conductive particles. Radiation is applied to the electrode preform sufficient to cure the radiation curable resin precursors into resin.

Du, Zhijia↗

RAPID DETERMINATION OF 237 NP AND PU ISOTOPES IN WATER BY INDUCTIVELY COUPLED PLASMA MASS SPECTROMETRY AND ALPHA SPECTROMETRY

A new method that allows rapid preconcentration and separation of plutonium and neptunium in water samples was developed for the measurement of {sup 237}Np and Pu isotopes by inductively-coupled plasma mass spectrometry (ICP-MS) and alpha spectrometry; a hybrid approach. {sup 238}U can interfere with {sup 239}Pu measurement by ICP-MS as {sup 238}UH{sup +} mass overlap and {sup 237}Np via peak tailing. The method provide enhanced removal of uranium by separating Pu and Np initially on TEVA Resin, then moving Pu to DGA resin for additional removal of uranium. The decontamination factor for uranium from Pu is almost 100,000 and the decontamination factor for U from Np is greater than 10,000. This method uses stacked extraction chromatography cartridges and vacuum box technology to facilitate rapid separations. Preconcentration is performed using a streamlined calcium phosphate precipitation method. Purified solutions are split between ICP-MS and alpha spectrometry so that long and short-lived Pu isotopes can be measured successfully. The method allows for simultaneous extraction of 20 samples (including QC samples) in 4 to 6 hours, and can also be used for emergency response. {sup 239}Pu, {sup 242}Pu and {sup 237}Np were measured by ICP-MS, while {sup 236}Pu, {sup 238}Pu, and {sup 239}Pu were measured by alpha spectrometry.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Combination of DGA and LN Columns: A Versatile Option for Isotope Production and Purification at Oak Ridge National Laboratory

The chromatographic resins DGA and LN have been used sequentially to separate curium, californium, plutonium, and various fission products (FPs) to obtain products with a pure radioisotope or a radioelement with high isotopic purity. This 2-step combination of resins has found applications in the 252 Cf and 238 Pu campaigns performed at Oak Ridge National Laboratory. Experiments have been carried out in glove boxes, shielded caves, and hot cells, demonstrating that these resins are adequate and maintain their performance in highly radiolytic environments. We find that using these resins has led to the recovery of curium highly enriched (>95%) in 248 Cm, the clean separation of 251 Cf for the superheavy element research, and the recovery of 147 Pm from the FP stream obtained during the 238 Pu production campaign while demonstrating that the raffinate post DGA is essentially free of transuranic elements.

07 ISOTOPE AND RADIATION SOURCES↗

Safety and Efficacy Assessment of Flow Redistribution by Occlusion of Intrahepatic Vessels Prior to Radioembolization in the Treatment of Liver Tumors

We evaluated the feasibility, safety, and efficacy of radioembolization (administered from one or two vascular points) after the redistribution of arterial blood flow in the liver in patients with hepatic neoplasms and arterial anatomic peculiarities (AAP). Twenty-four patients with liver neoplasms and AAP (graded according to Michel's classification) were included in the study. During pretreatment angiographic planning, all extrahepatic vessels that could feed the tumor were embolized and the intrahepatic vessels occluded in order to redistribute blood flow. The distribution of microspheres was initially assessed by using technetium-99m-labeled macroaggregated albumin ({sup 99m}Tc-MAA) from one of two vascular points before the administration of yttrium-90 ({sup 90}Y)-radiolabeled resin microspheres. Perfusion of lesions situated in the redistributed segments (L-RS) and nonredistributed segments (L-NRS) were compared by assessing the distribution of {sup 99m}Tc-MAA by SPECT/CT. Perfusion was graded as normal, reduced, or absent. {sup 90}Y resin microspheres were then injected from the same arterial sites as {sup 99m}Tc-MAA and the tumor response recorded 3 months later. The tumor response in L-RS was compared with that in L-NRS and graded as better, similar, or worse. Among 11 patients with type I AAP in whom mainly vessels in segments I-III or IV were occluded, perfusion of L-RS was graded as similar (n = 7) or reduced (n = 4). Among the remaining 13 patients with AAP types III (n = 3), V (n = 4), VIII (n = 3), and others (n = 3) in which aberrant arteries were occluded, perfusion of L-RS was graded as similar (n = 9), reduced (n = 3), or absent (n = 1). Overall, {sup 99m}Tc-MAA was present in the L-RS of 95.8% patients and the distribution of {sup 99m}Tc-MAA in L-RS and L-NRS were graded as similar in 66.6% of patients. Compared with lesions in the L-NRS, tumor response in L-RS was similar in 23 cases and worse in 1 case. No complications were recorded after the administration of {sup 90}Y resin microspheres. Redistribution of flow in L-RS is feasible and enables a safe and effective delivery of {sup 90}Y resin microspheres that are able to be distributed via intrahepatic collaterals and access the microvasculature of L-RS.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Evaluation of Visualization Using a 50/50 (Contrast Media/Glucose 5% Solution) Technique for Radioembolization as an Alternative to a Standard Sandwich Technique

BackgroundRadioembolization (RE) with {sup 90}yttrium ({sup 90}Y) resin microspheres generally employs a sandwich technique with separate sequential administration of contrast medium (CM), followed by vehicle (e.g., glucose 5% [G5] solution), then {sup 90}Y resin microspheres (in G5), then G5, and then CM again to avoid contact of CM and microspheres under fluoroscopic guidance. This study evaluates the visualization quality and safety of a modified sandwich technique with a 50/50-mixture of CM (Imeron 300) and G5 for administration of {sup 90}Y resin microspheres.Materials and MethodsA retrospective analysis of 81 RE procedures in patients with primary or secondary liver tumors was performed. The quality of angiographic visualization of the hepatic vessels was assessed before the first injection and immediately before the whole dose has been injected. Visualization and flow rate were graded on a 5-point scale: 1 = very good to 5 = not visible/no antegrade flow. Univariate logistic regression models and multiple linear regression models were used to evaluate the prognostic variables associated with visualization and flow scores.ResultsVisualization quality was inversely related to flow rate, the lower the flow rate the better the grade of the visualization. Visualization quality was also inversely related to body-mass-index (BMI). Performing RE with the 50/50-CM/G5 mixture resulted in a mean injection time for 1 GBq of 15 min. No clinically significant adverse events, including radiation-induced liver disease were reported.ConclusionRE with a 50/50-mixture of CM and G5 for administration of {sup 90}Y resin microspheres in a modified sandwich technique is a safe administration alternative and provides good visualization of hepatic vessels, which is inversely dependent on flow rate and BMI. Injection time was reduced compared with our experience with the standard sandwich technique.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Additive manufacturing of nanotube-loaded thermosets via direct ink writing and radio-frequency heating and curing

Direct Ink Writing (DIW) is an extrusion-based additive manufacturing method where the print medium is a liquid-phase ‘ink’ dispensed out of nozzles and deposited along digitally defined paths. Conventional DIW of thermosetting resins relies on viscosity modifying agents, novel crosslinking chemistries, and/or long curing schedules in an oven. Here we demonstrate the use of a co-planar radio frequency applicator to generate an electric field, which can be used to rapidly heat and cure nano-filled composite resins as they are printed. This method avoids the need for an oven or post- curing step. This process consists of a sequential print-and-cure cycle which allows for printing of high-resolution, multi-layered structures. Every extruded layer is partially cured using RF before depositing the next layer; this allows the printed part to maintain structural integrity. The process enables both increased throughput and decreased touch time relative to traditional manufacturing. Commercial epoxy resin with varied nano-filler loadings were examined as DIW candidates. After printing, the thermo-mechanical properties, surface finish, and shape retention of RF-cured samples were comparable to conventionally cured samples. Furthermore, this method of manufacturing establishes RF heating as a suitable alternative to conventional methods, facilitating rapid, free-form processing of thermosetting resins without a mold.

36 MATERIALS SCIENCE↗

Anticorrosive epoxy coatings from direct epoxidation of bioethanol fractionated lignin

The development of lignin-based anticorrosive epoxy coatings for steel protection is beneficial for both alleviating the fossil resource depletion and value-added utilization of lignin but remains a challenge due to the inherent heterogeneous structure of lignin. Here, in this study, we selectively extract the low molecular weight (MW) fraction of a crop residue-derived enzymatic hydrolysis lignin (EHL) through a bioethanol fractionation process and prepare epoxy resin by direct epoxidation of the bioethanol fractionated lignin (BFL). The coatings are then fabricated using 20–100 wt% of BFL-based epoxy resin (LEp) as the commercial epoxy resin substitute. The low MW and high p-hydroxyphenyl content of the BFL offer high solubility and good workability for BFL and LEp during epoxidation and coating production, respectively. Lignin-based coatings with 20–40 wt% LEp exhibit good adhesion property (5B) and superior corrosion resistance, compared to the commercial epoxy coating. Although coating with high LEp concentrations (i.e., 60–100 wt%) resulted in decreased adhesion strength, the coating with 100 wt% LEp still displayed corrosion protection performance comparable to that of the commercial epoxy coating. Overall, this study provides a simple and effective approach to converting lignin to epoxy resins for a wide variety of surface coating applications.

09 BIOMASS FUELS↗

Leaching studies for tin recovery from waste e-scrap

Printed circuit boards (PCBs) are the most essential components of all electrical and electronic equipments, which contain noteworthy quantity of metals, some of which are toxic to life and all of which are valuable resources. Therefore, recycling of PCBs is necessary for the safe disposal/utilization of these metals. Present paper is a part of developing Indo-Korean recycling technique consists of organic swelling pre-treatment technique for the liberation of thin layer of metallic sheet and the treatment of epoxy resin to remove/recover toxic soldering material. To optimize the parameters required for recovery of tin from waste PCBs, initially the bench scale studies were carried out using fresh solder (containing 52.6% Sn and 47.3% Pb) varying the acid concentration, temperature, mixing time and pulp density. The experimental data indicate that 95.79% of tin was leached out from solder material using 5.5 M HCl at fixed pulp density 50 g/L and temperature 90 Degree-Sign C in mixing time 165 min. Kinetic studies followed the chemical reaction controlled dense constant size cylindrical particles with activation energy of 117.68 kJ/mol. However, 97.79% of tin was found to be leached out from solder materials of liberated swelled epoxy resin using 4.5 M HCl at 90 Degree-Sign C, mixing time 60 min and pulp density 50 g/L. From the leach liquor of solder materials of epoxy resin, the precipitate of sodium stannate as value added product was obtained at pH 1.9. The Pb from the leach residue was removed by using 0.1 M nitric acid at 90 Degree-Sign C in mixing time 45 min and pulp density 10 g/L. The metal free epoxy resin could be disposed-of safely/used as filling material without affecting the environment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Highlights: • The parts mounted on printed circuit board (PCB) were liberated by underwater explosion and mechanical crushing. • The crushed PCB without surface-mounted parts was carbonized under inert atmosphere at 873 K to recover copper. • The multi-layered ceramic capacitors including nickel was carbonized at 873 K to recover nickel by the magnetic separation. • The tantalum powders were recovered from the molded resins by heat treatment at 723 and 823 K in air atmosphere and screening. • Energy and treatment cost of new process increased, however, the environmental burden decreased comparing conventional one. - Abstract: Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin. In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment. As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%. The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation. Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process. The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one. The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Soil burial biodegradation studies of palm oil-based UV-curable films

The palm oil-based ultraviolet (uv)-curable films were subjected to an outdoor soil burial test to investigate the biodegradation under natural environment. The films were burial in the soil experiment plot at the Nuclear Malaysia’s Dengkil complex. The uv-curable films were synthesized from the epoxidized palm oil acrylated (EPOLA) resin and the polyurethane palm oil (POBUA) resin, respectively. Biodegradation tests are more specific to burial film in soil experiments for 12 months under natural conditions. The biodegradability of palm oil resin based uv-curable films were investigated and compared with the petrochemical resin based film. The films properties were compared with respect to properties of the thermal characteristic, the crystallinity, the morphology and the weight loss which are analyzed using the thermogravimetric analysis (TGA), the differential scanning calorimetry (DSC), the scanning electron microscope (SEM), an optical microscope and the weight loss of film calculation. These findings suggested that the palm oil-based uv-curable films show quite satisfactory biodegradation levels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High T{sub g} and fast curing epoxy-based anisotropic conductive paste for electronic packaging

Herein, our main objective is to prepare the fast curing epoxy system with high glass transition temperature (T{sub g}) by incorporating the multifunctional epoxy resin into the mixture of diglycidyl ether of bisphenol A (DGEBA) as a major epoxy component and aromatic diamine as a hardener. Furthermore, the curing behavior as well as thermal and thermomechanical properties were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and thermomechanical analysis (TMA). It was found that T{sub g} obtained from tan δ of DGEBA/aromatic diamine system increased from 100 °C to 205 °C with the presence of 30 percentage by weight of multifunctional epoxy resin. Additionally, the isothermal DSC results showed that the multifunctional epoxy resin can accelerate the curing reaction of DGEBA/aromatic diamine system. Namely, a high degree of curing (∼90%) was achieved after a few minutes of curing at low temperature of 130 °C, owing to a large number of epoxy ring of multifunctional epoxy resin towards the active hydrogen atoms of aromatic diamine.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Epoxy nanodielectrics fabricated with in situ and ex situ techniques

In this study, we report fabrication and characterisation of a nanocomposite system composed of a commercial resin and extremely small (several nanometres in diameter) titanium dioxide particles. Nanoparticles were synthesised in situ with particle nucleation occurring inside the resin matrix. In this nanodielectric fabrication method, the nanoparticle precursor was mixed to the resin solution, and the nanoparticles were in situ precipitated. Note that no high shear mixing equipment was needed to improve particle dispersion - nanoparticles were distributed in the polymer matrix uniformly since particle nucleation occurs uniformly throughout the matrix. The properties of in situ nanodielectrics are compared to the unfilled resin and an ex situ nanocomposite. We anticipate that the presented in situ nanocomposite would be employed in high-temperature superconductivity applications. In additions, the improvement shown in the dielectric breakdown indicates that conventional high-voltage components and systems can be reduced in size with novel nanodielectrics.

36 MATERIALS SCIENCE↗

Development and Characterization of Healable Carbon Fiber Composites with a Reversibly Cross Linked Polymer

Carbon fiber reinforced polymer (CFRP) laminates with remendable cross-linked polymeric matrices were fabricated using a modified resin transfer mold (RTM) technique. The healable composite resin, bis-maleimide tetrafuran (2MEP4F), was synthesized by mixing two monomers, furan (4F) and maleimide (2MEP), at elevated temperatures. The fast kinetic rate of the reaction of polymer constituents requires a fast injection of the healable resin into the carbon fiber preform. The polymer viscosity as a function of time and temperature was experimentally quantified in order to optimize the fabrication of the composite material and to guarantee a uniform flow of the resin through the reinforcement. The method was validated by characterizing the thermo-mechanical properties of the polymerized 2MEP4F. Additionally, the thermo-mechanical properties of the remendable CFRP material were studied.

36 MATERIALS SCIENCE↗