Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REACTOR COMPONENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Effect of V and Ta on the precipitation behavior of 12%Cr reduced activation ferrite/martensite steel

12%Cr reduced activation ferrite/martensite steels are promising candidate materials for good corrosion and irradiation resistance used for supercritical water-cooled reactor cladding and in-core components. V and Ta are considered to have improved the creep strength of high Cr steels by precipitating as MX phase. In this paper, a series of trial products microalloyed with V and V–Ta are produced, and the microstructure is characterized after quenching at 1050 °C and tempering at 780 °C by using TEM method to investigate the effect of these elements on the precipitation behavior of 12%Cr reduced activation ferrite/martensite steel. The results from both the experimental observations and thermodynamic and kinetic calculations reveal that V and V–Ta can promote the stable MX precipitation instead of M{sub 2}X, thus increasing the volume fraction of M{sub 23}C{sub 6}. Two-phase separation behavior of the (Ta, V)(C, N) carbonitride into a Ta(V)C(N) phase and a V(Ta)N(C) phase in 12Cr3WVTa steel is observed and further discussed. - Highlights: • Microalloyed with V and V-Ta can promote the precipitation of MX instead of M{sub 2}X. • The presence of delta-ferrite in microstructure affects the morphology of MX. • Two-phase separation of MX carbonitride was observed in 12Cr3WVTa steel.

36 MATERIALS SCIENCE↗

Modernization of Technical Requirements for Licensing of Advanced Non-Light Water Reactors (Final Project Report)

Advanced (i.e., non-light-water) reactor technologies offer developers new opportunities to enhance the reliability, efficiency, and safety of nuclear power reactors through changes in fundamental design and operation. A variety of advanced design concepts are being developed that generally trend toward increased reliance on innovative, inherent, and passive safety features. Many of these features are substantially different from components now found in large light water reactors (LWRs) that dominate the commercial operating fleet. Similarly, non-light water reactor (non-LWR) suppliers are also pursuing market niches quite different from the regional baseload power generation sites typically associated with large LWR facilities.

42 ENGINEERING↗

SHARP User Manual

SHARP is an advanced modeling and simulation toolkit for the analysis of nuclear reactors. It is comprised of several components including physical modeling tools, tools to integrate the physics codes for multi-physics analyses, and a set of tools to couple the codes within the MOAB framework. Physics modules currently include the neutronics code PROTEUS, the thermal-hydraulics code Nek5000, and the structural mechanics code Diablo. This manual focuses on performing multi-physics calculations with the SHARP ToolKit. Manuals for the three individual physics modules are available with the SHARP distribution to help the user to either carry out the primary multi-physics calculation with basic knowledge or perform further advanced development with in-depth knowledge of these codes. This manual provides step-by-step instructions on employing SHARP, including how to download and install the code, how to build the drivers for a test case, how to perform a calculation and how to visualize the results. Since SHARP has some specific library and environment dependencies, it is highly recommended that the user read this manual prior to installing SHARP. Verification tests cases are included to check proper installation of each module. It is suggested that the new user should first follow the step-by-step instructions provided for a test problem in this manual to understand the basic procedure of using SHARP before using SHARP for his/her own analysis. Both reference output and scripts are provided along with the test cases in order to verify correct installation and execution of the SHARP package. At the end of this manual, detailed instructions are provided on how to create a new test case so that user can perform novel multi-physics calculations with SHARP. Frequently asked questions are listed at the end of this manual to help the user to troubleshoot issues.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Speciation and Concentrations of Metals in a Homogeneous Reactor Fuel Solution

Argonne National Laboratory scientists and engineers are collaborating with personnel from Babcock and Wilcox (B&W) to help optimize the design of their Medical Isotope Production System (MIPS). The major components of the MIPS are a homogeneous solution reactor containing low-enriched uranyl nitrate fuel, a molybdenum extraction system consisting of anion exchange columns, and an off-gas treatment facility. The MIPS project is of high priority because it would provide an industrial-scale domestic source of medical isotopes that is not currently available.

Jerden, J.↗

Synthesis Roadmap for Actinide Chloride Salts

Molten salt reactors (MSRs) are among the main advanced nuclear reactor types at the forefront of development by industry, with the support of the US government, for the next fleet of nuclear reactors to support the demand for energy in the coming decades. MSRs are highly unique because they are cooled and typically also fueled by molten salt. This quality brings about safety benefits such as low-pressure operation and self-stabilization of the neutron flux, operational benefits such as high-temperature operation and the ability for online refueling, and fuel and waste management benefits thanks to the flexibility of post-processing of molten salts and reprocessing options that involve removal of fission products and actinide separation. In fact, domestic deployment of molten salt (or molten salt–cooled) reactors is an approaching reality: a handful of molten salt reactor developers are planning to operate demonstration-scale reactors, as a step toward commercial-scale power reactors, within the decade. For example, Natura Resources received a construction permit in September 2024 for the deployment of MSR-1, which is a graphite-moderated thermal spectrum reactor, at Abilene Christian University. Also, TerraPower, in a collaborative effort with Southern Company and Idaho National Laboratory (INL), received approval from DOE in 2023 to proceed with the construction of the Molten Chloride Reactor Experiment (MCRE), a homogeneous chloride fast reactor at INL, and has begun assembly of system components. There are several other examples of developers at different stages of development of their own unique MSR designs (Jenet et al., 2025). As developers are in the process of obtaining approvals for their designs, deploying demonstration-scale reactors, and planning for their commercial-scale power reactors, there is a critical supply chain need for the synthesis of fuel for these reactors that must be addressed. The challenge generally is three-fold: (1) the quantity of fueled salt needed for these reactors is extraordinarily high (>100s of kilograms), but demonstrations of scaled-up techniques for fueled salt synthesis are significantly more limited than demonstrations of lab-scale syntheses; (2) each developer has a unique reactor design, which means different actinide halide elements in different carrier salts must be synthesized; and (3) there is a need for particularly high-purity salt so as to ensure the long-term operability of these reactors with minimal degradation to salt-wetted components, which necessitates synthesis techniques with high levels of quality control, repeatability, and well-characterized precursor and reactant materials. It is crucial that this supply chain challenge be addressed by demonstrating synthesis techniques that are scalable, de-risked, and well-documented so that these technologies may be adopted and utilized by industry to support the fueling needs of MSRs that are to come online within the next 10 years. With this supply chain challenge clearly defined for the developing MSR industry, it is important to consider that addressing such a challenge is oftentimes complex and context-dependent. There is not necessarily a single synthesis technique that can be scaled up and adopted to address the needs of all MSR developers; the synthesis approach that may be viable for producing a desired fuel salt will be entirely dependent on the exact salt composition needed, the quantity needed, purity needed, the refueling and waste plans, and the availability of a carrier salt for the fuel. Therefore, it is important to consider more broadly what synthesis techniques are available and have been demonstrated to understand the benefits, challenges, and general nuances that should be considered when evaluating a particular route for efficient production of high-purity fuel salts at scale.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Elevated temperature contact creep and friction of nickel-based superalloys using machine learning assisted finite element analysis

Nickel-based superalloys with superior thermochemical, mechanical, and tribological properties are highly utilized for critical components in several high temperature applications such as gas turbines and nuclear reactors. Inconel 617, in particular, is considered as one of the main candidate superalloys for tribo-components in very-high-temperature gas-cooled nuclear reactors. Recent findings indicate that this alloy grows unique surface oxide especially in a high-temperature helium environment with distinctive wear, friction, and contact properties. Here, this study investigates the high temperature contact area evolution and frictional behavior of Inconel 617 using finite element simulation and provides predictive models for the contact and friction performance at different normal loads, dwell times, and temperatures. High temperature helium-aged Inconel 617 top surface properties (up to 600 °C) are utilized along with a single asperity-based deformable elastic-plastic contact model under combined normal and tangential loading. Machine learning is used to assist the finite element results and to predict friction coefficient as well as contact area evolution. While a small difference is observed in the instantaneous friction coefficient (no dwell time) for all temperatures, friction coefficient increases considerably with dwell time. This shows that the effect of contact creep for longer dwell times significantly dominants the effect of high temperature variation in basic mechanical parameters such as modulus and yield strength. It is found that increasing temperature and dwell times lead to the friction coefficient increase, yet the dominance of dwell time effects decreases at higher temperatures and loads. While the analysis is presented for Inconel 617, the methodology is easy to be generalized and can be applied to other HT alloys.

36 MATERIALS SCIENCE↗

Mass optimization of a supercritical CO 2 Brayton cycle with a direct cooled nuclear reactor for space surface power

A long life, reliable, and compact surface power system will be necessary to achieve future goals in space exploration. This application uniquely requires the system to be optimized with respect to mass because system mass directly drives the space launch cost associated with transporting the system to its desired location. In this study, a supercritical CO 2 Brayton cycle coupled to a direct-cooled nuclear reactor was designed and optimized for mass. Robust models were developed for each Brayton cycle component in order to model the cycle performance. The three most massive components of this cycle are the radiator-based heat rejection system (subsequently referred to as the “radiator”), recuperator, and reactor. Mass correlations for the recuperator and radiator were established through interactions with component experts from industry and national labs. A reactor model was developed to predict the minimum mass reactor that satisfies neutronic and thermal limitations for given cycle conditions. The system optimization explores tradeoffs between the reactor, recuperator, and radiator sizes in order to identify the least massive system that will satisfy the power (40 kWe) and life (10 yr) requirements. To explore the effects of turbine inlet temperature on system mass, three types of microtube and shell recuperator technologies were considered: baseline stainless steel (which is consistent with the industry partner’s current designs), stainless steel with non-heritage tube sizes (which requires further development of manufacturing techniques), and Inconel (which is not a current/legacy design). Both stainless steel designs have a temperature limit of 823 K, which limits the turbine inlet temperature to 900 K. The baseline stainless steel design results in a combined mass of 738 kg. The stainless steel design allowing for non-heritage tube sizes reduces the combined mass to 674 kg (a 9% improvement). The Inconel design leads to an optimal turbine inlet temperature of 1120 K and reduces the combined mass to 391 kg (a 47% improvement). Furthermore, the interesting conclusion from this study include: (1) radiator mass dominates the total mass, and this drives the cycle to relatively high heat rejection temperatures resulting in a compressor inlet state point that is not close to the vapor dome; thus, the typical advantages of an sCO 2 system are not realized, and a working fluid with a higher critical temperature may be more suitable, and (2) neutronic limitations cause the reactor size to be relatively unaffected by the power level.

42 ENGINEERING↗

Radiation-Hardened Instrumentation, Sensors and Electronics

To assist the US Department of Energy in defining a course for Office of Nuclear Energy–funded radiation-hardened (rad-hard) electronics research, Oak Ridge National Laboratory (ORNL) will focus on three main tasks in FY21. The first task will investigate the survivability of silicon junction-gate field-effect transistors (Si-JFETs) through a 100 Mrad total ionizing dose (TID) experiment and report the test results. The second task will investigate wide bandgap (WBG)-based JFET devices and sources. The third task is an investigation into commercially available systems and components and will be performed to determine whether a standardized list of devices can be identified for reactor instrumentation application. If the devices are feasible, then this list will provide direction to designers and equipment suppliers for selection of components to meet specific reactor requirements.

42 ENGINEERING↗

Analysis of a tungsten sputtering experiment in DIII-D and code/data validation of high redeposition/reduced erosion

We analyze a DIII-D tokamak experiment where two tungsten spots on the removable DiMES divertor probe were exposed to 12 s of attached plasma conditions, with moderate strike point temperature and density (~20 eV, ~4.5 × 10 19 m –3 ), and 3% carbon impurity content. Both very small (1 mm diameter) and small (1 cm diameter) deposited samples were used for assessing gross and net tungsten sputtering erosion. The analysis uses a 3-D erosion/redeposition code package (REDEP/WBC), with input from a diagnostic-calibrated near-surface plasma code (OEDGE), and with focus on charge state resolved impinging carbon ion flux and energy. The tungsten surfaces are primarily sputtered by the carbon, in charge states +1 to +4. We predict high redeposition (~75%) of sputtered tungsten on the 1 cm spot—with consequent reduced net erosion—and this agrees well with post-exposure DiMES probe RBS analysis data. As a result, this study and recent related work is encouraging for erosion lifetime and non-contamination performance of tokamak reactor high-Z plasma facing components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Versatile TRISO fuel particle modeling in Bison

Tri-structural isotropic (TRISO) fuel particles are a key component in several previous and current reactors as well as in a variety of novel nuclear reactor designs. Interest in TRISO fuel is on the rise, necessitating considerable computer modeling of TRISO fuel behavior in order to support related design and licensing activities. The Bison nuclear fuel performance code, which offers a full set of capabilities for modeling TRISO fuels, makes it easier to explore the various important aspects of TRISO fuel behavior. One key advantage of Bison is its ability to create meshes in 1D, 2D, and 3D. Users can customize these meshes for specific geometries, mesh densities, and use cases. This enables a wide variety of analyses, including thermal, structural, mass diffusion, homogenization, and statistical failure analyses. Furthermore, the meshing capability simplifies analysts’ workflows. The inherent mesh generation capability eliminates the need for separate mesh-generating software and mesh file management. Also, the fact that the meshes are customizable makes it straightforward to automate an investigation over a range of geometric parameters or mesh densities. Here, the present paper highlights the ease with which Bison may be used to create meshes for both simple and relatively complex TRISO fuel particles, and it explores the types of analyses enabled by these meshes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Response of nickel surface to pulsed fusion plasma radiations

Nickel based alloys are being projected as suitable materials for some components of the next generation fusion reactor because of compatible thermal, electrical and mechanical properties. Pure nickel material is tested here for possibility of similar application purpose. Nickel samples (> 99.5 % purity) are exposed here to plasma radiations produced due to D-D fusion reaction inside an 11.5 kJ plasma focus device. The changes in the physical properties of the nickel surface at microscopic level which in turn change the mechanical properties are analyzed using scanning electron microscope, optical microscope, glancing incident X-ray diffractometer and Vicker's hardness gauge. The results are reported here.

36 MATERIALS SCIENCE↗

Analysis of Solar Receiver Performance for Chemical-Looping Integration With a Concentrating Solar Thermal System

This paper introduces a chemical-looping configuration integrated with a concentrating solar thermal (CST) system. The CST system uses an array of mirrors to focus sunlight, and the concentrated solar flux is applied to a solar receiver to collect and convert solar energy into thermal energy. The thermal energy then drives a thermal power cycle for electricity generation or provides an energy source to chemical processes for material or fuel production. Considerable interest in CST energy systems has been driven by power generation, with its capability to store thermal energy for continuous electricity supply or peak shaving. However, CST systems have other potential to convert solar energy into fuel or to support thermochemical processes. Thus, we introduce the concept of a chemical-looping configuration integrated with the CST system that has potential applications for thermochemical energy storage or solar thermochemical hydrogen production. The chemical-looping configuration integrated with a CST system consists of the following: a solar-receiver reactor for solar-energy collection and conversion, thermochemical energy storage, a reverse reactor for energy release, and system circulation. We describe a high-temperature reactor receiver that is a key component in the chemical-looping system. We also show the solar-receiver design and its performance analyzed by solar-tracing and thermal-modeling methods for integration within a CST system.

14 SOLAR ENERGY↗

A unified inelastic constitutive model for the average engineering response of Grade 91 steel

Grade 91 steel has been called out for use in advanced reactor intermediate heat exchangers and other components. The material has good high temperature creep resistance and thermal properties but has a complex microstructure that manifests as cyclic softening, work softening, and tension/compression asymmetry in its engineering mechanical response. We describe a unified viscoplastic model for the deformation of Grade 91 for an expected operating temperature range spanning from room temperature to approximately 650 C. The model transitions from a rate independent response at low temperatures and high strain rates to a rate dependent, unified viscoplastic response at high temperatures and low creep strain rates. The model captures work and cyclic softening in the material through combined isotropic kinematic hardening and captures observed tension/compression asymmetry and related anomalous ratcheting effects through a non-j2 flow term. A particular focus of the model is on capturing the average response of Grade 91 as determined from a wide collection of experimental data at many different temperatures, rather than the response of a single set of experiments at a particular temperature. The final model is suitable for the engineering design of nuclear components via inelastic analysis using the ASME Section III, Division 5 procedures.

Messner, M. C.↗

In-Vessel Devices Based on Capillary-Porous Systems with Liquid Metal for a Stationary Tokamak

The experience gained in developing, creating, and testing prototypes of stationary in-vessel devices based on capillary-porous systems with liquid lithium for the T-11M, T-10, KTM, and FTU tokamaks is presented. A promising scheme is proposed for designing liquid-metal-based in-vessel components with heat removal for thermonuclear reactors of the DEMO type and thermonuclear neutron sources.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The performance of NSF in BWR operating conditions - 2016-0062

NSF is a zirconium alloy in the zirconium-tin-niobium-iron family. The nominal alloy content is 1 % tin, 1 % niobium, and 0.4 % iron. The initial targeted component for NSF in boiling water reactors (BWRs) is the fuel assembly channel. A BWR fuel channel encases the fuel bundle such that boiling is confined within the channel while the water remains solid outside the channel. The BWR fuel channel also defines the gap between the bundles where the cruciform control blade inserts and withdraws to control the criticality of the core. The key performance requirements of the BWR fuel channel are dimensional stability (including both shape and thickness) and adequate mechanical properties to withstand the applied stresses. The distortion mechanisms that affect dimensional stability are fluence gradient-induced bow, shadow corrosion-induced bow, and elastic and creep bulge. Although NSF is known to have improved irradiation growth characteristics compared with both Zircaloy-2 and Zircaloy-4 that translates to increased dimensional stability in fuel channels, the BWR corrosion performance, tensile properties, and irradiation creep performance are less well known. This paper reports on the physical metallurgy of NSF, oxide thickness and hydrogen content after in-reactor operation, mechanical properties (both irradiated and unirradiated), in-reactor creep response, and irradiation growth and bow of NSF channels. (authors)

36 MATERIALS SCIENCE↗

Baseline Graphite Characterization: First Billet

The Next Generation Nuclear Plant Project Graphite Research and Development program is currently establishing the safe operating envelope of graphite core components for a very high temperature reactor design. To meet this goal, the program is generating the extensive amount of quantitative data necessary for predicting the behavior and operating performance of the available nuclear graphite grades. In order determine the in-service behavior of the graphite for the latest proposed designs, two main programs are underway. The first, the Advanced Graphite Creep (AGC) program, is a set of experiments that are designed to evaluate the irradiated properties and behavior of nuclear grade graphite over a large spectrum of temperatures, neutron fluences, and compressive loads. Despite the aggressive experimental matrix that comprises the set of AGC test runs, a limited amount of data can be generated based upon the availability of space within the Advanced Test Reactor and the geometric constraints placed on the AGC specimens that will be inserted. In order to supplement the AGC data set, the Baseline Graphite Characterization program will endeavor to provide supplemental data that will characterize the inherent property variability in nuclear-grade graphite without the testing constraints of the AGC program. This variability in properties is a natural artifact of graphite due to the geologic raw materials that are utilized in its production. This variability will be quantified not only within a single billet of as-produced graphite, but also from billets within a single lot, billets from different lots of the same grade, and across different billets of the numerous grades of nuclear graphite that are presently available. The thorough understanding of this variability will provide added detail to the irradiated property data, and provide a more thorough understanding of the behavior of graphite that will be used in reactor design and licensing. This report covers the development of the Baseline Graphite Characterization program from a testing and data collection standpoint through the completion of characterization on the first billet of nuclear-grade graphite. This data set is the starting point for all future evaluations and comparisons of material properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Testing of Small Graphite Samples for Nuclear Qualification

Accurately determining the mechanical properties of small irradiated samples is crucial to predicting the behavior of the overal irradiated graphite components within a Very High Temperature Reactor. The sample size allowed in a material test reactor, however, is limited, and this poses some difficulties with respect to mechanical testing. In the case of graphite with a larger grain size, a small sample may exhibit characteristics not representative of the bulk material, leading to inaccuracies in the data. A study to determine a potential size effect on the tensile strength was pursued under the Next Generation Nuclear Plant program. It focuses first on optimizing the tensile testing procedure identified in the American Society for Testing and Materials (ASTM) Standard C 781-08. Once the testing procedure was verified, a size effect was assessed by gradually reducing the diameter of the specimens. By monitoring the material response, a size effect was successfully identified.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

AGC-2 Graphite Preirradiation Data Package

The NGNP Graphite R&D program is currently establishing the safe operating envelope of graphite core components for a Very High Temperature Reactor (VHTR) design. The program is generating quantitative data necessary for predicting the behavior and operating performance of the new nuclear graphite grades. To determine the in-service behavior of the graphite for pebble bed and prismatic designs, the Advanced Graphite Creep (AGC) experiment is underway. This experiment is examining the properties and behavior of nuclear grade graphite over a large spectrum of temperatures, neutron fluences and compressive loads. Each experiment consists of over 400 graphite specimens that are characterized prior to irradiation and following irradiation. Six experiments are planned with the first, AGC-1, currently being irradiated in the Advanced Test Reactor (ATR) and pre-irradiation characterization of the second, AGC-2, completed. This data package establishes the readiness of 512 specimens for assembly into the AGC-2 capsule.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗