SEARCH · Engineering Papers

Results for “Plastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

All sources NASA NTRS DOE OSTI

NASA NTRS1986

The use of silver in self-lubricating coatings for extreme temperatures

The advantages and disadvantages of elemental silver as a tribological material are discussed. It is demonstrated that the relatively high melting point of 961 deg C, softness, marked plasticity, and thermochemical stability of silver combine to make this metal useful in thin film solid lubricant coatings over a wide temperature range. Disadvantages of silver during sliding, except when used as a thin film, are shown to be gross ploughing due to plastic deformation under load with associated high friction and excessive transfer to counterface surfaces. This transfer generates an irregular surface topography with consequent undesirable changes in bearing clearance distribution. Research to overcome these disadvantages of element silver is described. A comparison is made of the tribological behavior of pure silver with that of silver formulated with other metals and high-temperature solid lubricants. The composite materials are prepared by co-depositing the powdered components with an airbrush followed by furnace heat treatment or by plasma-spraying. Composite coatings were formulated which are shown to be self-lubricating over repeated, temperature cycles from low temperature to about 900 deg C.

Sliney, H. E.↗

NASA NTRS1986

Experimental study of a metal-matrix composite

A metal-matrix specimen was investigated using moire interferometry with 2400 lines/m (60,960 l/in.). The specimen was a 6-ply (0/ + or - 45)s boron-aluminum tensile coupon with a central slot. The unequal deformations in fibers and matrix were evident. Special attention was given to a plastic slip zone in the matrix. Normal and shear strains were calculated in the slip zone; the shear-strain concentration factor rose dramatically with the onset of plastic slip and continued to rise gradually with load to 95 percent of the failure load. The precipitous change from maximum tensile strain in one fiber to zero tensile strain in the neighboring fiber was accommodated by the very high shear strains of the matrix in the slip zone. Experimental considerations are discussed: shear strains are independent of rigid-body rotations; simplified strain calculations are justified; averaging across the narrow slip region and the influence of finite thickness of the specimen grating contribute to underestimation of peak strains.

Post, D.↗

NASA NTRS1986

The cyclic stress-strain behavior of PWA 1480 at 650 deg C

The monotonic plastic flow behavior of several single crystal nickel-base, superalloys has been shown to vary significantly with crystallographic orientation. In the present study, the cyclic plastic flow response of one such alloy, PWA 1480, was examined at 650 deg C in air. Single crystal specimens aligned near several crystallographic directions were tested in fully reversed, total-strain-controlled low cycle fatigue tests at a frequency of 0.1 Hz. The cyclic stress-strain response and general cyclic hardening behavior was analyzed as a function of crystallographic orientation and inelastic strain range.

Gabb, T. P.↗

NASA NTRS1986

High temperature monotonic and cyclic deformation in a directionally solidified nickel-base superalloy

Directionally solidified (DS) MAR-M246+Hf was tested in tension and fatigue, at temperatures from 20 C to 1093 C. Tests were performed on (001) oriented specimens at strain rates of 50 % and 0.5 % per minute. In tension, the yield strength was constant up to 704 C, above which the strength dropped off rapidly. A strong dependence of strength on strain rate was seen at the higher temperatures. The deformation mode was observed to change from heterogeneous to homogeneous with increasing temperature. Low Cycle Fatigue tests were done using a fully reversed waveform and total strain control. For a given plastic strain range, lives increased with increasing temperature. For a given temperature strain rate had a strong effect on life. At 704 C, decreasing strain rates decreased life, while at the higher temperatures, decreasing strain rates increased life, for a given plastic strain range. These results could be explained through considerations of the deformation modes and stress levels. At the higher temperatures, marked coarsening caused beneficial stress reductions, but oxidation limited the life. The longitudinal grain boundaries were found to influence slip behavior. The degree of secondary slip adjacent to the boundaries was found to be related to the degree of misorientation between the grains.

Huron, Eric S.↗

NASA NTRS1986

Development of passive radiation detectors of improved sensitivity

The future development of a solid track high energy particle detector is discussed. The goal is to improve the sensitivity and lower the threshold of the detector. One most widely used material for such purpose is a plastic commercially known as CR-39. A scheme is presented which involves changing the formula of the monomer, diethylene glycol-bis-allyl carbonate. This is to be accomplished by substituting some heteroatoms for H and substituting sulfur atoms for oxygen in the ether linkages. Use of a new plasticizer to make the etched surface clearer than what has been accomplished as of today is suggested. Possible improvement in acquiring better tracks and increasing the ratio of V sub T/V sub B was planned. This is to be accomplished by changing the composition of the etchants, etching time, and etching temperature.

Chakrabarty, M. R.↗

NASA NTRS1987

Probabilistic finite elements

In the Probabilistic Finite Element Method (PFEM), finite element methods have been efficiently combined with second-order perturbation techniques to provide an effective method for informing the designer of the range of response which is likely in a given problem. The designer must provide as input the statistical character of the input variables, such as yield strength, load magnitude, and Young's modulus, by specifying their mean values and their variances. The output then consists of the mean response and the variance in the response. Thus the designer is given a much broader picture of the predicted performance than with simply a single response curve. These methods are applicable to a wide class of problems, provided that the scale of randomness is not too large and the probabilistic density functions possess decaying tails. By incorporating the computational techniques we have developed in the past 3 years for efficiency, the probabilistic finite element methods are capable of handling large systems with many sources of uncertainties. Sample results for an elastic-plastic ten-bar structure and an elastic-plastic plane continuum with a circular hole subject to cyclic loadings with the yield stress on the random field are given.

Belytschko, Ted↗

NASA NTRS1987

Effect of abrasive grit size on wear of manganese-zinc ferrite under three-body abrasion

Wear experiments were conducted using replication electron microscopy and reflection electron diffraction to study abrasion and deformed layers produced in single-crystal Mn-Zn ferrites under three-body abrasion. The abrasion mechanism of Mn-Zn ferrite changes drastically with the size of abrasive grits. With 15-micron (1000-mesh) SiC grits, abrasion of Mn-Zn ferrite is due principally to brittle fracture; while with 4- and 2-micron (4000- and 6000-mesh) SiC grits, abrasion is due to plastic deformation and fracture. Both microcracking and plastic flow produce polycrystalline states on the wear surfaces of single-crystal Mn-Zn ferrites. Coefficient of wear, total thickness of the deformed layers, and surface roughness of the wear surfaces increase markedly with an increase in abrasive grit size. The total thicknesses of the deformed layers are 3 microns for the ferrite abraded by 15-micron SiC, 0.9 microns for the ferrite abraded by 4-micron SiC, and 0.8 microns for the ferrite abraded by 1-micron SiC.

Miyoshi, Kazuhisa↗

NASA NTRS1987

Substructure analysis using NICE/SPAR and applications of force to linear and nonlinear structures

Parallel computing studies are presented for a variety of structural analysis problems. Included are the substructure planar analysis of rectangular panels with and without a hole, the static analysis of space mast, using NICE/SPAR and FORCE, and substructure analysis of plane rigid-jointed frames using FORCE. The computations are carried out on the Flex/32 MultiComputer using one to eighteen processors. The NICE/SPAR runstream samples are documented for the panel problem. For the substructure analysis of plane frames, a computer program is developed to demonstrate the effectiveness of a substructuring technique when FORCE is enforced. Ongoing research activities for an elasto-plastic stability analysis problem using FORCE, and stability analysis of the focus problem using NICE/SPAR are briefly summarized. Speedup curves for the panel, the mast, and the frame problems provide a basic understanding of the effectiveness of parallel computing procedures utilized or developed, within the domain of the parameters considered. Although the speedup curves obtained exhibit various levels of computational efficiency, they clearly demonstrate the excellent promise which parallel computing holds for the structural analysis problem. Source code is given for the elasto-plastic stability problem and the FORCE program.

Razzaq, Zia↗

NASA NTRS1986

Fatigue crack propagation rate model based on a dislocation mechanism

It has been noted that the crack propagation exponent p for most metals usually varies between values of 2 and 4, and that the motion of dislocations plays an important part in determining the exponent p. Attention is presently given to the significance of the exponent p in terms of the motion of dislocations, in view of the theory of thermally activated plastic flow and the cumulative plastic strain concept for a failure criterion.

Mazumdar, P. K.↗

NASA NTRS1986

Dislocation mechanism based model for stage II fatigue crack propagation rate

Repeated plastic deformation, which of course depends on dislocation mechanism, at or near the crack tip leads to the fatigue crack propagation. By involving the theory of thermally activated flow and the cumulative plastic strain criterion, an effort is made here to model the stage II fatigue crack propagation rate in terms of the dislocation mechanism. The model, therefore, provides capability to ascertain: (1) the dislocation mechanism (and hence the near crack tip microstructures) assisting the crack growth, (2) the relative resistance of dislocation mechanisms to the crack growth, and (3) the fracture surface characteristics and its interpretation in terms of the dislocation mechanism. The local microstructure predicted for the room temperature crack growth in copper by this model is in good agreement with the experimental results taken from the literature. With regard to the relative stability of such dislocation mechanisms as the cross-slip and the dislocation intersection, the model suggests an enhancement of crack growth rate with an ease of cross-slip which in general promotes dislocation cell formation and is common in material which has high stacking fault energy (produces wavy slips). Cross-slip apparently enhances crack growth rate by promoting slip irreversibility and fracture surface brittleness to a greater degree.

Mazumdar, P. K.↗

NASA NTRS1986

Crack growth in single-crystal silicon

Crack growth in single-crystal silicon at room temperature in air was evaluated by double torsion (DT) load-relaxation method and monitored by acoustic emission (AE) technique. Both DT and AE methods indicated lack of subcritical crack growth in silicon. At the critical stress intensity factor, the crack front was found to be jumping several times in a 'mirror' region and then followed by fast crack growth in a 'hackle' region. Hackle marks were found to be associated with plastic deformation at the tip of the fast moving crack. No dislocation etch pits were found in the 'mirror' region, in which crack growth may result from interatomic bonds broken at the crack tip under stress without any plastic deformation. Acoustic emission appears to be spontaneously generated from both interatomic bonds broken and dislocation generation at the moving crack tip during the crack growth in single-crystal silicon.

Chen, C. P.↗

NASA NTRS1987

J-integral estimates for cracks in infinite bodies

An analysis and discussion is presented of existing estimates of the J-integral for cracks in infinite bodies. Equations are presented which provide convenient estimates for Ramberg-Osgood type elasto-plastic materials containing cracks and subjected to multiaxial loading. The relationship between J and the strain normal to the crack is noted to be only weakly dependent on state of stress. But the relationship between J and the stress normal to the crack is strongly dependent on state of stress. A plastic zone correction term often employed is found to be arbitrary, and its magnitude is seldom significant.

Dowling, N. E.↗

NASA NTRS1987

Deformation of a metal-matrix tensile coupon with a central slot - An experimental study

A metal-matrix specimen was investigated using high-sensitivity moire interferometry. In-plane displacement fields were analyzed at various load levels from 15 to 95 percent of the failure load. Normal and shear strains were determined from displacement gradients. Highly localized plastic slip zones occured in the ductile aluminum matrix tangent to the ends of the slot. Shear strains in the slip zone were an order of magnitude greater than the largest normal strains in the specimen. The shear-strain concentration factor rose dramatically with the onset of plastic slip and continued to rise gradually with load to 95 percent of the failure load. Upon unloading, shear strains in the slip zone remained precariously high.

Post, Daniel↗

NASA NTRS1987

Nucleus-nucleus interactions between 20 and 65 GeV per nucleon

A hybrid electronic-counter/emulsion-chamber instrument was exposed to high-energy cosmic rays on a balloon. The data on 105 nucleus-nucleus collisions in the energy range 20-65 GeV/nucleon and for incident nuclear charges Zp in the range of 22 to 28 are presented. Inclusive characteristics of particle production on different targets (plastic, emulsion, and lead) are shown and compared with models based on the superposition of nucleon-nucleus interactions. Features of a subset of the more central collisions with a plastic target and some characteristics of individual events with the highest multiplicity of produced particles are described.

Burnett, T. H.↗

NASA NTRS1988

Extending The Shelf Life Of Blood Platelets

New method of storing human blood platelets extends vitality for transfusions. Packaged as suspension in sterile liquid in plastic blood bags. Each bag placed between pair of plastic grids, and rubberbands placed around sandwich thus formed to hold together. Stored upright in open air or in container through which air pumped at rate of at least 45 L/min. Ensures that platelets receive ample oxygen and expiratory carbon dioxide form platelets removed before pH drops to harmful levels.

Surgenor, Douglas M.↗

NASA NTRS1987

Mechanisms of rolling contact spalling

The results of a study aimed at analyzing the mechanical material interactions responsible for rolling contact spalling of the 440 C steel, high pressure oxygen turbopump bearings are presented. A coupled temperature displacement finite element analysis of the effects of friction heating under the contact is presented. The contact is modelled as a stationary, heat generating, 2 dimensional indent in an elastic perfectly plastic half-space with heat fluxes up to 8.6 x 10000 KW/m sq comparable to those generated in the bearing. Local temperatures in excess of 1000 C are treated. The calculations reveal high levels of residual tension after the contact is unloaded and cools. Efforts to promote Mode 2/Mode 3 fatigue crack growth under cyclic torsion in hardened 440 C steel are described. Spalls produced on 440 C steel by a 3 ball/rod rolling contact testing machine were studied with scanning microscopy. The shapes of the cyclic, stress strain hysteresis loops displayed by hardened 440 C steel in cyclic torsion at room temperature are defined for the plastic strain amplitudes encountered in rolling/sliding contact. Results of these analyses are discussed in detail.

Kumar, A. M.↗

NASA NTRS1988

Approximate method for predicting the permanent set in a beam in vacuo and in water subject to a shock wave

An approximate method to compute the maximum deformation and permanent set of a beam subjected to shock wave laoding in vacuo and in water was investigated. The method equates the maximum kinetic energy of the beam (and water) to the elastic plastic work done by a static uniform load applied to a beam. Results for the water case indicate that the plastic deformation is controlled by the kinetic energy of the water. The simplified approach can result in significant savings in computer time or it can expediently be used as a check of results from a more rigorous approach. The accuracy of the method is demonstrated by various examples of beams with simple support and clamped support boundary conditions.

Stiehl, A. L.↗

NASA NTRS1988

MHOST: An efficient finite element program for inelastic analysis of solids and structures

An efficient finite element program for 3-D inelastic analysis of gas turbine hot section components was constructed and validated. A novel mixed iterative solution strategy is derived from the augmented Hu-Washizu variational principle in order to nodally interpolate coordinates, displacements, deformation, strains, stresses and material properties. A series of increasingly sophisticated material models incorporated in MHOST include elasticity, secant plasticity, infinitesimal and finite deformation plasticity, creep and unified viscoplastic constitutive model proposed by Walker. A library of high performance elements is built into this computer program utilizing the concepts of selective reduced integrations and independent strain interpolations. A family of efficient solution algorithms is implemented in MHOST for linear and nonlinear equation solution including the classical Newton-Raphson, modified, quasi and secant Newton methods with optional line search and the conjugate gradient method.

Nakazawa, S.↗