Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material Response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Galileo probe forebody entry thermal protection - Aerothermal environments and heat shielding requirements

Solutions are presented for the aerothermal heating environments and the material thermal response for the forebody heatshield on the candidate 242 kg Galileo probe entering the modeled nominal and cold-dense Jovian atmospheres. In the flowfield analysis, a finite difference procedure was employed to obtain benchmark predictions of pressure, radiation and convective heating rates (both laminar and turbulent) and the corresponding wall blowing obtained under the steady state approximation. The fluxes over the probe flank were found to be in a range where spallation is an important mass loss mechanism. The predicted heating rates were also used as boundary conditions for a charring materials ablation which was used to predict thermochemical based surface recession, mass loss and bondline temperatures. The contingency factor of 30% currently employed by NASA was found to be insufficient for entry into the cold-dense atmosphere.

Nicolet, W. E.↗

MIAMI: Microscope and ion accelerator for materials investigations

A transmission electron microscope (TEM) with in situ ion irradiation has been built at the University of Salford, U.K. The system consists of a Colutron G-2 ion source connected to a JEOL JEM-2000FX TEM via an in-house designed and constructed ion beam transport system. The ion source can deliver ion energies from 0.5 to 10 keV for singly charged ions and can be floated up to 100 kV to allow acceleration to higher energies. Ion species from H to Xe can be produced for the full range of energies allowing the investigation of implantation with light ions such as helium as well as the effects of displacing irradiation with heavy inert or self-ions. The ability to implant light ions at energies low enough such that they come to rest within the thickness of a TEM sample and to also irradiate with heavier species at energies sufficient to cause large numbers of atomic displacements makes this facility ideally suited to the study of materials for use in nuclear environments. TEM allows the internal microstructure of a sample to be imaged at the nanoscale. By irradiating in situ it is possible to observe the dynamic evolution of radiation damage which can occur during irradiation as a result of competing processes within the system being studied. Furthermore, experimental variables such as temperature can be controlled and maintained throughout both irradiation and observation. This combination of capabilities enables an understanding of the underlying atomistic processes to be gained and thus gives invaluable insights into the fundamental physics governing the response of materials to irradiation. Details of the design and specifications of the MIAMI facility are given along with examples of initial experimental results in silicon and silicon carbide.

36 MATERIALS SCIENCE↗

Detonation Waves in High Explosives

A material at high temperature can react or decompose. For an energetic material, the reaction is exothermic and releases chemical energy that would further increase the temperature. Under some circumstances, when a reaction is triggered, such a reaction can propagate and the material rapidly releases a large amount of energy giving rise to an explosion. Examples of such materials are aerosols, suspensions of solid particles or liquid droplets in a gas; such as coal dust, grain dust and fuel-air explosions. Frequently, explosions are due to accidents. A spectacularly destructive example is the recent explosion of a large quantity of ammonium nitrate (thousands of tons) in Beirut, Lebanon (August 2020); see for example Beirut explosion. Ammonium nitrate is used as a fertilizer. It and the aerosols are not considered to be explosives due to the limited conditions for which an explosion can occur. An aerosol gets the oxidizer from the surrounding air. Burning requires diffusion of the oxidizer to the particle surface where the reaction occurs. A large density of small particles is required for a fast enough reaction to support an explosion. In contrast, an explosive is an energetic material with both fuel and oxidizer mixed on a molecular scale (either premixed gases or within molecules of a solid). This allows fast enough reactions over a wide range of conditions to support a self-propagating reactive wave known as a detonation wave. A detonation wave can be controlled and an explosive used for useful purposes such as in mining, construction, demolition, explosive welding, argon flash lamp, pulsed power using a magnetic flux generator [see also Goforth et al., 2015], jet cutter with shaped charge, explosive art, and generating conditions to study the response of materials at high strain rates and high pressures [see for example, Marsh, 1980]. Explosives are also used in conventional munitions and nuclear weapons. The focus of this book is on the theory and phenomenology of solid high explosives (HEs); in particular, plastic-bonded explosives (PBXs). Some aspects of detonation wave theory are needed to interpret explosive data. Hence, the theory is presented before the detonation wave phenomenology. A familiarity with fluid flow, specifically the notion of shock waves and the shock loci are assumed. In the remainder of this chapter we give a brief overview on the basic properties of detonation waves and PBXs.

36 MATERIALS SCIENCE↗

Soft x-ray free-electron laser induced damage to inorganic scintillators

An irreversible response of inorganic scintillators to intense soft x-ray laser radiation was investigated at the FLASH (Free-electron LASer in Hamburg) facility. Three ionic crystals, namely, Ce:YAG (cerium-doped yttrium aluminum garnet), PbWO4 (lead tungstate), and ZnO (zinc oxide), were exposed to single 4.6 nm ultra-short laser pulses of variable pulse energy (up to 12 μJ) under normal incidence conditions with tight focus. Damaged areas produced with various levels of pulse fluences, were analyzed on the surface of irradiated samples using differential interference contrast (DIC) and atomic force microscopy (AFM). The effective beam area of 22.2 ± 2.2 μm2 was determined by means of the ablation imprints method with the use of poly(methyl methacrylate) - PMMA. Applied to the three inorganic materials, this procedure gave almost the same values of an effective area. The single-shot damage threshold fluence was determined for each of these inorganic materials. The Ce:YAG sample seems to be the most radiation resistant under the given irradiation conditions, its damage threshold was determined to be as high as 660.8 ± 71.2 mJ/cm2. Contrary to that, the PbWO4 sample exhibited the lowest radiation resistance with a threshold fluence of 62.6 ± 11.9 mJ/cm2. The threshold for ZnO was found to be 167.8 ± 30.8 mJ/cm2. Both interaction and material characteristics responsible for the damage threshold difference are discussed in the article.

36 MATERIALS SCIENCE↗

On the measurement of hardness at high strain rates by nanoindentation impact testing

Recent advances in electronics have enabled nanomechanical measurements with very low noise, fast time constants and high data acquisition rates. Furthermore, these capabilities open the door for a wide range of ultra-fast nanomechanical testing. Given the inherent dynamic nature of high-speed testing, a thorough understanding of the testing system's dynamics and electronics is extremely important for accurate measurements. In this work, an analytical framework that includes the mechanical and electronic contributions of the instrument and the material constitutive response is presented to provide guidelines for performing high strain rate measurements of hardness by nanoindentation testing. Simple closed-form solutions that provide insights on the choice of test methodology, test parameters and instrument design are presented along with the strain rate range over which accurate measurements can be performed with the commercially available nanoindenters.

36 MATERIALS SCIENCE↗

Irradiation Testing of Additively Manufactured Materials for LWR Applications: Alloy 718 and 316L Stainless Steel

The objective of this NSUF Project is to assess the changes in irradiated additively manufactured (AM) material properties as compared to non-irradiated material. Type 316L stainless steel and Alloy 718 samples were produced using Direct Metal Laser Melting (DMLM) fabrication. Materials produced from this fabrication method have several potential applications within the nuclear industry as reactor internal repair parts, fuel debris resistant filters, or fuel spacers within existing light water reactors (LWRs). AM materials have been shown to achieve equivalent mechanical behavior in simulated reactor environments as compared to wrought materials, but have significantly more flexibility when it comes to unique design features. The increased component design flexibility makes these AM materials an attractive choice for both current LWR applications as well as for small modular reactor (SMR) designs. Prior to use of these materials in reactor fleet operation, the industry as a whole must evaluate the effects of irradiation on their material properties. Standard 0.4 inch thick Compact Tension specimens and SSJ3 type tensile bars were neutron irradiated at the Advanced Test Reactor to ~1 dpa for the purpose of performing a variety of mechanical tests in a range of simulated environments applicable to LWRs. For the ductile austenitic Type 316L stainless steel, the irradiated data will be used to confirm that the AM process produces materials with properties that are equivalent to wrought materials under testing conditions applicable to LWR operation. Transmission electron microscopy analysis was also performed in order to understand microstructural and microchemical changes induced in each material in response to neutron irradiation. If possible, data collected from these AM 316L samples will be used to remove fluence limits from specifications of ASME code cases for this alloy, which will give vendors much more flexibility in building future components.

36 - MATERIALS SCIENCE↗

The DISTINCTIVE University Consortium: Theme 2: PuO{sub 2} and Fuel Residues - 18132

The safe and secure management of Pu is a matter of serious international concern, with ∼250 t of separated Pu currently stockpiled worldwide. Nearly 50% of this material is in long-term storage in the UK whilst the British government develops its options for final treatment and disposition. Options for this are: (i) reuse as a fuel in modern reactors (e.g. as MOX fuel or within a fast reactor) prior to disposal; (ii) prompt immobilisation for disposal as soon as is practicable; or, (iii) continued long term storage (prior to disposition). The focus of the work presented here is options (ii) and (iii). The R and D needs of both are now pressing: in option (iii) due to it being the current default; in option (ii) because of a comparative lack of R and D on Pu conditioning and packaging due to policy uncertainty as to whether it would be disposed of in a Geologic Disposal Facility (GDF). Addressing these needs is complicated by Pu's high radioactivity, decay heat and radiotoxicity, nuclear safeguard requirements and, for some UK Pu contaminated materials targeted for disposal, poor inventory. Thus, there is also a critical requirement for underpinning research on characterisation methods for Pu bearing materials. In response to these needs, the DISTINCTIVE Consortium (Decommissioning, Immobilisation and Storage Solutions for Nuclear Waste Inventories, a multi-disciplinary collaboration of 11 universities and 3 key industry partners from across the UK's civil nuclear sector) has been seeking to: - Understand how the structure and properties of PuO{sub 2} change with time in the presence of H{sub 2}O. - Understand the roles these processes play in gaseous product evolution from PuO{sub 2} in storage. - Understand radiation-induced amorphization and dissolution kinetics of Pu waste forms. - Develop novel, fast neutron based radiometric methods for the quantification, isotopic composition assessment and remote imaging of Pu-bearing materials. This paper describes recent progress made towards achieving these objectives. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Robust Coupling between Structural and Electronic Transitions in a Mott Material

The interdependences of different phase transitions in Mott materials are fundamental to the understanding of the mechanisms behind them. One of the most important relations is between the ubiquitous structural and electronic transitions. Using IR spectroscopy, optical reflectivity, and x-ray diffraction, we show that the metal-insulator transition is coupled to the structural phase transition in V 2 O 3 films. This coupling persists even in films with widely varying transition temperatures and strains. Our findings are in contrast to recent experimental findings and theoretical predictions. Using V 2 O 3 as a model system, we discuss the pitfalls in measurements of the electronic and structural states of Mott materials in general, calling for a critical examination of previous work in this field. Furthermore, our findings also have important implications for the performance of Mott materials in next-generation neuromorphic computing technology.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Prediction of the Elastic-Plastic Stress/Strain Response for Injection-Molded Long-Fiber Thermoplastics

This paper proposes a model to predict the elastic-plastic response of injection-molded long-fiber thermoplastics (LFTs). The model accounts for elastic fibers embedded in a thermoplastic resin that exhibits the elastic-plastic behavior obeying the Ramberg-Osgood relation and J-2 deformation theory of plasticity. It also accounts for fiber length and orientation distributions in the composite formed by the injection-molding process. Fiber orientation was predicted using the anisotropic rotary diffusion model recently developed by Phelps and Tucker for LFTs. An incremental procedure using the Eshelby’s equivalent inclusion method and the Mori-Tanaka model is proposed to compute the overall stress increment resulting from an overall strain increment for an aligned fiber composite that contains the same fiber volume fraction and length distribution as the actual composite. The incremental response of the later is then obtained from the solution for the aligned fiber composite that is averaged over all possible fiber orientations using the orientation averaging method. Failure during incremental loading is predicted using the Van Hattum-Bernado model. The elastic-plastic and strength prediction model for LFTs was validated against the experimental stress-strain results obtained for long glass fiber/polypropylene specimens.

36 MATERIALS SCIENCE↗

Mesoscale simulation of granular materials under weak shock compaction–pore size distribution effects

This research established a systematic method to generate various pore-size distributions (PSDs) and studied the effect of PSDs on the shock compaction response of granular materials using two-dimensional mesoscale simulations under identical porosity. Simulations utilized various PSDs for three particle shapes (circle, ellipse, and square). Contacting particle configurations using three PSDs, characterized by spatially uniform distributed pores to heterogeneous distributed pores, and non-contacting particle configurations under a single case of PSD were tested. The PSD of generated particle sets was characterized using coordination number, mean diameter, and bimodality coefficient as statistical metrics. Mesoscale simulations showed that regardless of the conditions of pore distributions, shock compaction of granular materials consistently demonstrates a precursor, shock compaction front, and end. However, the shock compaction velocity of contacting particles was dependent on the PSDs despite the constant initial porosity. The compaction velocity was faster in particle configurations with relatively uniform pore distributions than in heterogeneous pore distributions, which our study demonstrated can be attributed to particle rearrangement during compaction. Circular-shaped particles had high sensitivity in shock compaction response to the various PSDs. Furthermore, a contacting particle configuration tended to propagate the shock compaction wave relatively faster than particles that were in a non-contact configuration. This study established the relative importance of considering PSD as a metric over the coordination number in studies of the shock compaction response of granular materials. Further, insights are provided on the evolving shock substructure to characterize the shock compaction response of granular materials.

36 MATERIALS SCIENCE↗

Spatiotemporal temperature and density characterization of high-power atmospheric flashover discharges over inert poly(methyl methacrylate) and energetic pentaerythritol tetranitrate dielectric surfaces

A flashover arc source that delivered up to 200 mJ on the 100s-of-ns time-scale to the arc and a user-selected dielectric surface was characterized for studying high-explosive kinetics under plasma conditions. The flashover was driven over thin pentaerythritol tetranitrate (PETN) and poly(methyl methacrylate) (PMMA) dielectric films and the resultant plasma was characterized in detail. Time- and space-resolved temperatures and electron densities of the plasma were obtained using atomic emission spectroscopy. The hydrodynamics of the plasma was captured through fast, visible imaging. Fourier transform infrared spectroscopy (FTIR) was used to characterize the films pre- and post-shot for any chemical alterations. Time-resolved infrared spectroscopy (TRIR) provided PETN depletion data during the plasma discharge. For both types of films, temperatures of 1.6-1.7 eV and electron densities of {approx}7-8 x 10{sup 17}/cm{sup 3}{approx}570 ns after the start of the discharge were observed with temperatures of 0.6-0.7 eV persisting out to 15 {mu}s. At 1.2 {mu}s, spatial characterization showed flat temperature and density profiles of 1.1-1.3 eV and 2-2.8 x 10{sup 17}/cm{sup 3} for PETN and PMMA films, respectively. Images of the plasma showed an expanding hot kernel starting from radii of {approx}0.2 mm at {approx}50 ns and reaching {approx}1.1 mm at {approx}600 ns. The thin films ablated or reacted several hundred nm of material in response to the discharge. First TRIR data showing the in situ reaction or depletion of PETN in response to the flashover arc were successfully obtained, and a 2-{mu}s, 1/e decay constant was measured. Preliminary 1 D simulations compared reasonably well with the experimentally determined plasma radii and temperatures. These results complete the first steps to resolving arc-driven PETN reaction pathways and their associated kinetic rates using in situ spectroscopy techniques.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Unexpected Observation of Disorder and Multiple Phase-Transition Pathways in Shock-Compressed Zr

The response of materials under dynamic compression involves a complex interplay of various deformation mechanisms aimed at relieving shear stresses, yielding a remarkable diversity in material behavior. Here, in this Letter, we utilize femtosecond x-ray diffraction coupled with nanosecond laser compression to reveal an intricate competition between multiple shear-relieving mechanisms within an elemental metal. Our observations in shocked-compressed single-crystal Zr indicate a disorder-mediated shear relaxation at lower pressures. Above the phase-transition pressure, we observe the increasing contribution of structural phase transition in relieving shear stress. We detect not one but three concurrent pathways during the transition from the hcp to a hex-3 structure. These complex dynamics are partially corroborated through multimillion-atom molecular dynamics simulations employing a machine-learned interatomic potential. Our observation of multiple concurrent pathways and disorder during shock compression underscore the far greater intricacies in the dynamic response of metals than previously assumed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A parametric study of slow dynamic nonlinear elasticity with comparisons to models

Several phenomenological models that aspire to quantitative description of anomalous nonlinear mesoscopic elasticity are reviewed and compared with laboratory measurements. This class of nonlinearity, best known perhaps for slow dynamics and aging, is seen widely in imperfectly consolidated granular solids but is not well understood. Typical slow dynamic tests show that a modest conditioning oscillatory "pump" strain depresses material stiffness, which then recovers like the logarithm of time after conditioning ceases. Several phenomenological models based on physical arguments have been proposed that predict the material stiffness response to arbitrary pump strain histories during conditioning and recovery. Approximate closed form and numerical solutions to the models are presented that predict the quantitative influence of three key pump parameters: the pump's strain amplitude, the pump's strain rate, and the pump’s duration. Laboratory measurements on Berea sandstone, concrete and a confined single aluminum bead find that slow dynamic responses are linear in pump strain and independent of pump frequency. Measurements also show that, after pump-off, stiffness recovers over times far longer than the pump duration. These observations and others are compared to model predictions. One of the considered models, based on a picture of fast brittle damage and slow healing, successfully matches all these behaviors.

36 MATERIALS SCIENCE↗

Modification of the MTS model for high strain-rate behavior of TI-6AL-4V

The Mechanical Threshold Stress (MTS) model provides excellent predictive capabilities for the material constitutive response for a wide range of temperatures and strain rates. However, the MTS model fails to capture the rapidly increasing yield stress at high strain rate behavior as the deformation controlling mechanism transitions from thermal activation to drag mechanisms, only capturing the linear behavior. Further, the model typically over predicts the flow stress behavior at yield and post yield due to its use of a constant work hardening rate parameter derived from the stress–strain response at constant saturation stress. An alternative approach to fitting portions of the MTS model is investigated and mathematical models are developed to address these issues. The results show that with appropriate experimental data, the mechanical threshold stress and work hardening rate parameters within the MTS model can quite easily and accurately be modified to extend applicability to high strain rate behavior and more accurately model the initial flow stress behavior at early work hardening rates without modification of the functions core to the MTS model itself.

36 MATERIALS SCIENCE↗

Long Duration Exposure Facility experiment M0003 deintegration observation data base

The four trays (2 leading edge and 2 trailing edge) of the M0003 materials experiment on the Long Duration Exposure Facility (LDEF) contained 1274 samples from 20 subexperiments. The complete sample complement represented a broad range of materials, including thin film optical coatings, paints, polymer sheets and tapes, adhesives, and composites, for use in various spacecraft applications, including thermal control, structures, optics, and solar power. Most subexperiments contained sets of samples exposed on both the leading and trailing edge trays of LDEF. Each individual sample was examined by high resolution optical microscope during the deintegration of the subexperiments from the M0003 trays. Observations of the post-flight condition of the samples made during this examination were recorded in a computer data base. The deintegration observation data base is available to requesters on floppy disk in 4th Dimension for the Macintosh format. Over 3,000 color macrographs and photomicrographs were shot to complement the observation records and to document the condition of the individual samples and of the M0003 trays. The photographs provide a visual comparison of the response of materials in leading and trailing edge LDEF environments. The Aerospace Corporate Archives is distributing photographs of the samples and hard copies of the database records to the general public upon request. Information on obtaining copies of the data base disks and for ordering photographs and records of specific samples or materials are given.

Gyetvay, S. R.↗

Long Duration Exposure Facility experiment M0003 deintegration observation database

The four trays of the M0003 materials experiment on LDEF contained 1274 samples from 19 subexperiments. The complete sample complement represented a broad range of materials, including thin film optical coatings, paints, polymer sheets and tapes, adhesives, and composites, for use in various spacecraft applications including thermal control, structures, optics, and solar power. Since some subexperiments included duplicate samples exposed on the leading and trailing edge trays, for 9 week, 19 week, 40 week, and 68 month durations on both the leading and trailing edges, comparisons provided a valuable time history of degradation. During the deintegration of the subexperiments from the M0003 trays, each sample was examined using bright field, dark field, and Normarski light microscopy techniques. Over 3,000 color macrographs and photomicrographs were made of the condition of M0003 trays and the individual samples. Records of the condition of the samples, photographic records, and all available references of publications on postflight analyses on each sample were collected in a database. The photographs provide a visual comparison of the response of materials common to various subexperiments in different LDEF environments. Aerospace Corporation is distributing the database records and photographs and written records on materials of interest from the database is given in this presentation.

Gyetvay, S. R.↗

Crystallographic Evidence of Size-Dependent Bond Flexibility in Metal–Organic Framework Nanocrystals

Size-dependent electronic, magnetic, and optical behavior suggests that metal–organic frameworks become softer materials as their particle sizes decrease, but direct evidence is lacking. Here, we report variable-temperature powder X-ray diffraction data of Fe(1,2,3-triazolate)2 particles that offer crystallographic insight into size-dependent bond flexibility. Rietveld refinement reveals size-dependent positive thermal expansion upon downsizing the crystalline domains from 178 to 9 nm, with a 6-fold increase from 16 MK –1 to 96 MK –1 . Here, this behavior occurs in tandem with size-dependent elongation of metal–ligand bonds and increasing thermal displacement parameters, consistent with pronounced metal-linker bond lability. We propose that these effects, as well as size-dependent annealing of crystallite sizes, originate from the high charge density and surface stress of smaller particles. Taken together, these results provide structural evidence that size reduction serves as a synthetic route to controlling the dynamic response of materials to external stimuli.

Crystals↗

Operando leaching of pre-incorporated Al and mechanism in transition-metal hybrids on carbon substrates for enhanced charge storage

Insufficient exposure and utilization of active sites often induces an inferior reactivity for transition-metal-based two-dimensional (2D) materials. In response, we for the first time propose a universal "nano-tailoring" strategy to incorporate abundant defects and active sites into low-crystallinity nanosheets by electrochemically leaching of Al species. With MnAl layered double hydroxides (LDHs) as a representative example, potassium-birnessite MnO 2 (AK-MnO 2 ) with oxygen vacancies and abundant edge sites is successfully produced. The oxygen vacancies are shown to help optimize the electron-transfer and ion-adsorption capability. These integrated advantages endow the AK-MnO 2 with a high capacitance value of 239 F g –1 at 100 A g –1 . By further combining with soft X-ray absorption spectroscopy techniques, we unravel that the reducibility of M 2+ in M 2+ Al-LDH serves as the key descriptor for the reconstruction rate. Here, this "nano-tailoring" strategy can provide some important implications and clues to manipulating 2D materials for efficient energy storage and conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗