Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Laser Applications”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

High-Isp Mode Of Pulsed Laser-Electromagnetic Hybrid Accelerator For Space Propulsion Applications

A fundamental study of a newly developed rectangular pulsed laser-electromagnetic hybrid thruster was conducted. Laser-ablation plasma in the thruster was induced through laser beam irradiation onto a solid target and accelerated by electrical means instead of direct acceleration only by using a laser beam. The performance of the thrusters was evaluated by measuring the mass shot and impulse bit. As results, significantly high specific impulses up to 7,200 sec were obtained at the charge energies of 8.6 J. In addition, typical thrust efficiency varied between 11.8% and 21.3% depending on the charge energy.

43 PARTICLE ACCELERATORS↗

A plasma-based non-intrusive point source for acoustic beamforming applications

A laser-generated plasma acoustic point source is used to directly measure the point spread function (PSF) of a microphone phased array. In beamforming analysis of microphone phased array data, the true acoustic field is convolved with the array's PSF. By directly measuring the PSF, corrections to the array analysis can be computed and applied. The acoustic source is measured in an open-jet aeroacoustic facility to evaluate the effects of sampling rate, microphone installation, source shift, reflections, shear layer refraction and model presence. Results show that measurements exhibit behavior consistent with theory with regard to source shift and shear layer refraction. Application of a measured PSF in beamforming analysis shows the process provides an effective in-situ method for array calibration both with and without flow and allows for corrections to incorporate reflections and scattering. The technique improves the agreement of beamforming results with the true spectrum of a known source, especially in the presence of reflections.

phased array↗

In Situ Laser Crystallization of Amorphous Silicon for TFT Applications: Controlled Ultrafast Studies in the Dynamic TEM

An in situ method for studying the role of laser energy on the microstructural evolution of polycrystalline Si is presented. By monitoring both laser energy and microstructural evolution simultaneously in the dynamic transmission electron microscope, information on grain size and defect concentration can be correlated directly with processing conditions. This proof of principle study provides fundamental scientific information on the crystallization process that has technological importance for the development of thin film transistors. In conclusion, we successfully developed a method for studying UV laser processing of Si films in situ on nanosecond time scales, with ultimate implications for TFT application improvements. In addition to grain size distribution as a function of laser energy density, we found that grain size scaled with laser energy in general. We showed that nanosecond time resolution allowed us to see the nucleation and growth front during processing, which will help further the understanding of microstructural evolution of poly-Si films for electronic applications. Future studies, coupled with high resolution TEM, will be performed to study grain boundary migration, intergranular defects, and grain size distribution with respect to laser energy and adsorption depth.

36 MATERIALS SCIENCE↗

Laser driven proton beam for the applications: toward ultra-high intensity and short pulse proton beam

As a benchmark experiment to realize a novel and compact laser driven proton accelerator whose significant features are high number density in a short pulse width (approxns), 2.4 MeV laser driven proton beam is stably focused at 1 Hz repetition rate by using a pair of permanent quadrupole magnets (PMQs) with large apertures whose diameters and field strengths are 3.5 cm and 55 T/m for the first and 2.3 cm and 60 T/m for the second magnets, respectively. The proton beam has been focused to a focal spot of 3x8 mm{sup 2} in horizontal and vertical direction (full width at half maximum) at 650approxmm from the source, which is well reproduced by the simulation. The further optimization of the focusing system will sure to pave a way to the novel proton accelerator with which we can investigate the physics appeared in the short time scale as well as that in a high energy density matter, oncology, astrophysics, and so on.

43 PARTICLE ACCELERATORS↗

Note: Deep ultraviolet Raman spectrograph with the laser excitation line down to 177.3 nm and its application

Deep UV Raman spectrograph with the laser excitation line down to 177.3 nm was developed in this laboratory. An ellipsoidal mirror and a dispersed-subtractive triple monochromator were used to collect and disperse Raman light, respectively. The triple monochromator was arranged in a triangular configuration with only six mirrors used. 177.3 nm laser excited Raman spectrum with cut-off wavenumber down to 200 cm{sup −1} and spectral resolution of 8.0 cm{sup −1} can be obtained under the condition of high purity N{sub 2} purging. With the C–C σ bond in Teflon selectively excited by the 177.3 nm laser, resonance Raman spectrum of Teflon with good quality was recorded on the home-built instrument and the σ-σ{sup *} transition of C–C bond was studied. The result demonstrates that deep UV Raman spectrograph is powerful for studying the systems with electronic transition located in the deep UV region.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Advanced flat top laser heating system for high pressure research at GSECARS: application to the melting behavior of germanium

Laser heating plays an essential role for in-situ high pressure high temperature studies into the physical and chemical properties of materials in the diamond anvil cell (DAC) and minerals at conditions relevant to the Earth's deep interior. High temperature experiments in the multi-Mbar (over 100 GPa) pressure range require the use of very small samples and consequently the utmost stability and controllability of the laser heating is crucial. To accomplish this, we have modified the laser heating system at GSECARS employing newly developed beam shaping optics combined with two diode-pumped, single mode fiber lasers. Varying the settings of the laser heating system, we were able to shape the beam to almost any desired intensity profile and size on the surface of the sample in the DAC, including tight focus, flat top, trident and doughnut types. The advantages and excellent performance of the flat top laser heating (FTLH) technique were demonstrated in melting experiments on germanium in the DAC at pressures up to 40 GPa.

36 MATERIALS SCIENCE↗

Laser anemometer signals - Visibility characteristics and application to particle sizing

Investigations have been conducted concerning the characteristics of the visibility function as determined by the parameters of the laser anemometer system and the electromagnetic scattering properties of the particles. Experiments have been performed to evaluate the backscatter visibility of signals from a symmetric, s polarization laser anemometer as a function of the particle diameter and a parameter ratio. The results have been compared with the predictions of an analysis based on Mie's scattering theory. The analysis has also been used to evaluate the effects of the collecting aperture's size and location.

Adrian, R. J.↗

A relative performance analysis of atmospheric Laser Doppler Velocimeter methods.

Evaluation of the effectiveness of atmospheric applications of a Laser Doppler Velocimeter (LDV) at a wavelength of about 0.5 micrometer in conjunction with dual scatter LDV illuminating techniques, or at a wavelength of 10.6 micrometer with local oscillator LDV illuminating techniques. Equations and examples are given to provide a quantitative basis for LDV system selection and performance criteria in atmospheric research. The comparative study shows that specific ranges and conditions exist where performance of one of the methods is superior to that of the other. It is also pointed out that great care must be exercised in choosing system parameters that optimize a particular LDV designed for atmospheric applications.

Farmer, W. M.↗

Laser production and heating of plasma for MHD application

Experiments have been made on the production and heating of plasmas by the absorption of laser radiation. These experiments were performed to ascertain the feasibility of using laser-produced or laser-heated plasmas as the input for a magnetohydrodynamic (MHD) generator. Such a system would have a broad application as a laser-to-electricity energy converter for space power transmission. Experiments with a 100-J-pulsed CO2 laser were conducted to investigate the breakdown of argon gas by a high-intensity laser beam, the parameters (electron density and temperature) of the plasma produced, and the formation and propagation of laser-supported detonation (LSD) waves. Experiments were also carried out using a 1-J-pulsed CO2 laser to heat the plasma produced in a shock tube. The shock-tube hydrogen plasma reached electron densities of approximately 10 to the 17th/cu cm and electron temperatures of approximately 1 eV. Absorption of the CO2 laser beam by the plasma was measured, and up to approximately 100 percent absorption was observed. Measurements with a small MHD generator showed that the energy extraction efficiency could be very large with values up to 56 percent being measured.

Jalufka, N. W.↗

A Survey of Transparent Conducting Films and Optoelectrical Materials for High Optical Power Applications

The lifetime laser damage performance of a wide range of transparent conductive materials is assessed, including ultrathin metal films, doped metal oxides, doped compound semiconductors, and graphene whose carrier densities span five orders of magnitude from 10 18 to 10 23 cm -3 . Lifetime laser damage thresholds are determined by exposing material surfaces to repeated nanosecond laser pulses at near IR wavelengths (1064 nm). Near threshold fluences, two distinct damage modes, i.e., bulk and discrete, emerge depending on carrier density. These bulk and discrete damage modes are attributed to free carrier-induced bulk and localized, defect-driven absorption processes, respectively. For polycrystalline films with free carrier densities greater than ≈10 20 cm -3 , laser damage thresholds are less than 5 J cm -2 . In contrast, bulk absorption is not apparent at thresholds substantially higher than ≈10 J cm-2 in single-crystal films with free carrier concentrations lower than ≈10 19 cm -3 . By increasing thickness, films with lower carrier densities can deliver relevant levels of sheet conductance (<200 Ω sq -1 ) while remaining transparent. These lifetime laser damage threshold measurements offer systematic criteria to select materials aimed at handling high optical powers in optoelectronics devices and emerging plasmonic and metamaterials for lasers.

36 MATERIALS SCIENCE↗

Kr II laser-induced fluorescence for measuring plasma acceleration

We present the application of laser-induced fluorescence of singly ionized krypton as a diagnostic technique for quantifying the electrostatic acceleration within the discharge of a laboratory cross-field plasma accelerator also known as a Hall effect thruster, which has heritage as spacecraft propulsion. The 728.98 nm Kr II transition from the metastable 5d{sup 4}D{sub 7/2} to the 5p{sup 4}P{sub 5/2}{sup Ring-Operator} state was used for the measurement of laser-induced fluorescence within the plasma discharge. From these measurements, it is possible to measure velocity as krypton ions are accelerated from near rest to approximately 21 km/s (190 eV). Ion temperature and the ion velocity distributions may also be extracted from the fluorescence data since available hyperfine splitting data allow for the Kr II 5d{sup 4}D{sub 7/2}-5p{sup 4}P{sub 5/2}{sup Ring-Operator} transition lineshape to be modeled. From the analysis, the fluorescence lineshape appears to be a reasonable estimate for the relatively broad ion velocity distributions. However, due to an apparent overlap of the ion creation and acceleration regions within the discharge, the distributed velocity distributions increase ion temperature determination uncertainty significantly. Using the most probable ion velocity as a representative, or characteristic, measure of the ion acceleration, overall propellant energy deposition, and effective electric fields may be calculated. With this diagnostic technique, it is possible to nonintrusively characterize the ion acceleration both within the discharge and in the plume.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Comparing the use of mid-infrared versus far-infrared lasers for mitigating damage growth on fused silica

Laser-induced growth of optical damage can limit component lifetime and, therefore, increase operating costs of large-aperture fusion-class laser systems. While far-infrared (IR) lasers have been used previously to treat laser damage on fused silica optics and render it benign, little is known about the effectiveness of less-absorbing mid-IR lasers for this purpose. In this study, we quantitatively compare the effectiveness and efficiency of mid-IR (4.6 {mu}m) versus far-IR (10.6 {mu}m) lasers in mitigating damage growth on fused silica surfaces. The nonlinear volumetric heating due to mid-IR laser absorption is analyzed by solving the heat equation numerically, taking into account the temperature-dependent absorption coefficient {alpha}(T) at {lambda}=4.6 {mu}m, while far-IR laser heating is well described by a linear analytic approximation to the laser-driven temperature rise. In both cases, the predicted results agree well with surface temperature measurements based on IR radiometry, as well as subsurface fictive temperature measurements based on confocal Raman microscopy. Damage mitigation efficiency is assessed using a figure of merit (FOM) relating the crack healing depth to laser power required, under minimally ablative conditions. Based on our FOM, we show that, for cracks up to at least 500 {mu}m in depth, mitigation with a 4.6 {mu}m mid-IR laser is more efficient than mitigation with a 10.6 {mu}m far-IR laser. This conclusion is corroborated by direct application of each laser system to the mitigation of pulsed laser-induced damage possessing fractures up to 225 {mu}m in depth.

36 MATERIALS SCIENCE↗

Measurement and Analysis of Porosity in Al-10Si-1Mg Components Additively Manufactured by Selective Laser Melting

Aluminum alloys are candidate materials for weight critical applications because of their excellent strength and stiffness to weight ratio. However, defects such as voids decrease the strength and fatigue life of these alloys, which can limit the application of Selective Laser Melting. In this study, the average volume fraction, average size, and size distribution of pores in Al10-Si-1Mg samples built using Selective Laser Melting have been characterized. Synchrotron high energy X-rays were used to perform computed tomography on volumes of order one cubic millimeter with a resolution of approximately 1.5 μm. Substantial variations in the pore size distributions were found as a function of process conditions. Even under conditions that ensured that all locations were melted at least once, a significant number density was found of pores above 5 μm in diameter.

36 MATERIALS SCIENCE↗

Comparison of laser-based mitigation of fused silica surface damage using mid- versus far-infrared lasers

Laser induced growth of optical damage can limit component lifetime and therefore operating costs of large-aperture fusion-class laser systems. While far-infrared (IR) lasers have been used previously to treat laser damage on fused silica optics and render it benign, little is known about the effectiveness of less-absorbing mid-IR lasers for this purpose. In this study, they quantitatively compare the effectiveness and efficiency of mid-IR (4.6 {micro}m) versus far-IR (10.6 {micro}m) lasers in mitigating damage growth on fused silica surfaces. The non-linear volumetric heating due to mid-IR laser absorption is analyzed by solving the heat equation numerically, taking into account the temperature-dependent absorption coefficient {alpha}(T) at {lambda} = 4.6 {micro}m, while far-IR laser heating is well-described by a linear analytic approximation to the laser-driven temperature rise. In both cases, the predicted results agree well with surface temperature measurements based on infrared radiometry, as well as sub-surface fictive temperature measurements based on confocal Raman microscopy. Damage mitigation efficiency is assessed using a figure of merit (FOM) relating the crack healing depth to laser power required, under minimally-ablative conditions. Based on their FOM, they show that for cracks up to at least 500 {micro}m in depth, mitigation with a 4.6 {micro}m mid-IR laser is more efficient than mitigation with a 10.6 {micro}m far-IR laser. This conclusion is corroborated by direct application of each laser system to the mitigation of pulsed laser-induced damage possessing fractures up to 225 {micro}m in depth.

42 ENGINEERING↗

Progress in developing laser based post irradiation examination infrastructure

To be able to understand the performance of reactor fuels and materials, irradiated materials must be characterized effectively and efficiently in high rad environments. This characterization work is performed remotely and in environments generally hostile to instrumentation. Laser based characterization techniques provide the ability to operate remotely and robustly in a hot-cell environment. Laser based instrumentation also can provide high spatial resolution suitable for scanning and imaging large areas. The INL is currently developing three laser based Post Irradiation Examination (PIE) stations for the Hot Fuel Examination Facility (HFEF) at the INL. These laser based systems will characterize irradiated materials and fuels. The characterization systems are the following: -) laser shock, -) laser based ultrasonic C-scan system and -) gas assay, sample and recharge system (GASR, up-grade to an existing system). The laser shock technique will characterize material properties and failure loads/mechanisms in various materials such as Light Water Reactor (LWR) fuel, plate fuel, and next generation fuel forms in high radiation areas. The laser shock-technique induces large amplitude shock waves to mechanically characterize interfaces such as the fuel-clad bond. As part of the laser shock system, a laser-based ultrasonic C-scan system will be used to detect and characterize de bonding caused by the application of the laser shock as well as performing classical non-destructive evaluation testing and imaging functions such as microstructure characterization, flaw detection and dimensional metrology. A spectroscopy capability can be added later as the salient components to perform Light Induced Breakdown Spectroscopy will be in place. Additional fiber ports in the feed-through will also enable future spectroscopic techniques to be efficiently installed and operated. The purpose of the GASR is to measure the pressure/volume of the plenum of an irradiated fuel element/capsule and obtain fission gas samples for analysis. The study of pressure and volume in the plenum of an irradiated fuel element/capsule and the analysis of fission gases released is important to understanding the performance of reactor fuels and materials. The main function of the laser in this application is to puncture the fuel rod or plate to allow the fission gas to escape and if necessary to weld the hole close. This system may also be used to measure the pressure/volume of other components (such as control blades) and obtain gas samples from these components for analysis. The GASR upgrade will match the functionality of the current system and provide these important functions on fuels made from current and future engineered materials. The GASR station will also have the inherent capability to perform cutting welding and joining functions within a hot-cell. The extra fiber ports built into the hot cell feed-through will also enable the efficient installation of future laser processing work benches. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Noncontacting Laser Inspection System for Dimensional Profiling of Space Application Thermal Barriers

A noncontacting, two-dimensional (2-D) laser inspection system has been designed and implemented to dimensionally profile thermal barriers being developed for space vehicle applications. In a vehicle as-installed state, thermal barriers are commonly compressed between load sensitive thermal protection system (TPS) panels to prevent hot gas ingestion through the panel interface during flight. Loads required to compress the thermal barriers are functions of their construction, as well as their dimensional characteristics relative to the gaps in which they are installed. Excessive loads during a mission could damage surrounding TPS panels and have catastrophic consequences. As such, accurate dimensional profiling of thermal barriers prior to use is important. Due to the compliant nature of the thermal barriers, traditional contact measurement techniques (e.g., calipers and micrometers) are subjective and introduce significant error and variability into collected dimensional data. Implementation of a laser inspection system significantly enhanced the method by which thermal barriers are dimensionally profiled, and improved the accuracy and repeatability of collected data. A statistical design of experiments study comparing laser inspection and manual caliper measurement techniques verified these findings.

Taylor, Shawn C.↗

Applicability of semiclassical methods for modeling laser-enhanced fusion rates in a realistic setting

In the context of the potential laser-induced enhancement to the rates of DHe 3 and DT fusion, we discuss the frequently-used Wentzel-Kramers-Brillouin (WKB) method and the imaginary-time method (ITM). For static external electric fields, we find that these methods predict significant enhancement to the fusion cross section for electric-field strengths > 10 14 V/m, especially at low values (≈ keV) for the enter-of-mass (CoM) energy. When considering dynamic electric fields, this enhancement can be amplified by considering increased photon frequencies. However, we also pro- vide a review of the region of laser-parameter phase space where these semiclassical methods are applicable. Here, we conclude that this allowable region decreases for higher photon frequencies in con-junction with lower values for the electric-field strength, motivating the need for future experiments to test the predictions of these methods and their ranges of validity.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Evaluation of Manganese Doped Ca5(PO4)3F as a Near Infrared (1-2 microns) Solid-State Laser Material

Tunable solid-state lasers are of enormous interest for applications including fundamental spectroscopy, remote sensing of the earth atmosphere, medical surgery, and optical communications. Efficient and widely tunable lasers have been developed for the 800-1100 nm region based on transition metal doped insulators like e.g. Ti:Sapphire. The development of transition metal lasers operating at longer wavelength, however, has been limited by the luminescence efficiency of existing materials. We are currently evaluating Mn doped Ca5(PO4)3F as a new solid-state laser material for the 1-2 micro-m region. Preliminary spectroscopic studies revealed that Mn:Ca5(PO4)3F exhibits an intense near infrared luminescence which extends from 1100-1300 nm. Based on lifetime measurements we estimated the luminescence quantum efficiency to be as high as 90 deg./0 at room temperature. The near infrared luminescence properties of Mn doped Ca5(PO4)3F and its potential for solid-state laser applications will be discussed in detail.

Turner, Matthew↗