SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Glandless valve shuts down high-pressure fluid systems when severe shock from an explosion or earthquake occurs. The valve uses a pendulum to support the valve closure plug in the open position. When jarred, the valve body is moved relative to the pendulum and the plug support is displaced, allowing the plug to seat and be held by spring pressure.
Shock tubes with linear explosive driver for helium and air, determining performance by high speed camera measurements
Dissimilar metals tubular joints between 2219-T851 aluminum alloy and 304L stainless steel were fabricated and tested to evaluate bonding processes. Joints were fabricated by four processes: (1) inertia (friction) weldings, where the metals are spun and forced together to create the weld; (2) explosive welding, where the metals are impacted together at high velocity; (3) co-extrusion, where the metals are extruded in contact at high temperature to promote diffusion; and (4) swaging, where residual stresses in the metals after a stretching operation maintain forced contact in mutual shear areas. Fifteen joints of each type were prepared and evaluated in a 6.35 cm (2.50 in.) O.D. size, with 0.32 cm (0.13 in.) wall thickness, and 7.6 cm (3.0 in) total length. The joints were tested to evaluate their ability to withstand pressure cycle, thermal cycle, galvanic corrosion and burst tests. Leakage tests and other non-destructive test techniques were used to evaluate the behavior of the joints, and the microstructure of the bond areas was analyzed.
The presence of broad, shallow absorptions caused by O VI ions were revealed from UV spectra observations recorded by the Copernicus satellite for thirty-two stars. A table lists survey data on the stars observed for which values of the O VI column densities or their upper limits are extracted. Interstellar rather than circumstellar origin is evident from observation of the lack of correspondence between radical velocities of the stars and those of the O VI profiles. The presence of a low-density high-temperature phase of interstellar gas produced by supernova explosions is suggested.
Synthetic-aperture radar imagery from the Shuttle Imaging Radar - mission B (SIR-B) was collected in October 1984 over the central Andes between 20 deg S and 24 deg S and also south of 42 deg S. Despite signal-strength problems that drastically reduced the signal-to-noise ratio of the images, volcanic features of both areas show up well. In particular, ignimbrite sheets formed by large explosive eruptions stand out as very strong radar reflectors. High backscatter is apparently caused by erosional relief on the ignimbrites at scales ranging from the radar wavelength (23 cm for SIR-B) to the 30-200-m scale of quebradas (gullies and canyons). The consistent regional erosional pattern appears unrelated to the emplacement of the ignimbrites, and is probably caused by preferential eolian erosion in the directions of the prevailing wind. Hand-held space photographs, ground observations, and Landsat Thematic Mapper imagery support the interpretation of the ignimbrite radar signature. The Chilean volcano Michinmahuida was imaged by four radar data takes at different incidence angles, which show tectonic, glacial, and volcanic features of that nearly inaccessible and often cloud-covered region. Stereo viewing of radar images from two data takes greatly enhances the geologic interpretation of this rugged area.
The invention is an apparatus and a process for the explosive joining of a flyer plate and a base plate. The apparatus consists of a flyer plate positioned over a base plate. The flyer plate has a notch containing a filler material in intimate contact with the flyer plate. An adhesive means holds a ribbon explosive partially overlapping the notch in the flyer plate. A detonating means initiates the ribbon explosive that drives the flyer plate to accomplish a high velocity, angular collision between the mating surfaces. This collision creates surface melts and effacing bonding, resulting in electron sharing linkups between the plates. An unbonded tab fractures at a base of the notch leaving a bond to an edge of the attached flyer plate.
We report followup investigations of Einstein x-ray observations of the Upper Scorpius OB association. We identify 28 low mass pre-main sequence stars as counterparts of x-ray sources in the approximately = 7 square degrees of the OB association observed. Based on kinematics and lithium abundances, these stars are low mass members of the OB association. We use optical spectra and optical and near-IR photometry to determine the stellar luminosities, effective temperatures, masses, and ages. We show that the bolometric corrections and effective temperatures of the G and K stars are consistent with those of subgiants. The low mass stars have isochronal ages of 1-2 Myr, depending on the choice of evolutionary models, with very small dispersion (sigma approximately = 1 Myr). This age is significantly younger than the 5-6 Myr found for the more massive B stars. The small dispersion in stellar ages, less than 10% the sound-crossing time of the association, suggests that star formation was triggered. We present two scenarios for star formation in this association. In the two-episode scenario, formation of the low mass stars was triggered by a supernova explosion, and the low mass stars form quickly, with high efficiency. Alternatively, high and low mass star formation was all initiated at the same time, some 5-6 Myr ago, and the apparent systematic age difference is an artifact of how the isochrones are dated. The effect of the supernova is to terminate mass accretion and yield an apparently coeval population. We show that the incompleteness in the x-ray sampling is about 65%, and is strongly dependent on stellar mass. After correction for incompleteness, we estimate there are about 2000 low mass members (stellar mass less than 2 solar mass) of this association. The mass function in this association is indistinguishable from that of the field. The ratio of naked to classical T Tauri stars is much larger than in Tau-Aur, and may be attributable to the local environment. We also present observations of eight ROX sources associated with the rho Oph cloud, and observations of non-pre-main sequence (PMS) stars in our fields.
The combustion of metals is a field with important practical applications in rocket propellants, high-temperature flames, and material synthesis. Also, the safe operation of metal containers in high-pressure oxygen systems and with cryogenic fuels and oxidizers remains an important concern in industry. The increasing use of metallic components in spacecraft and space structures has also raised concerns about their flammability properties and fire suppression mechanisms. In addition, recent efforts to embark on unmanned and manned planetary exploration, such as on Mars, have also renewed the interest in metal/carbon-dioxide combustion as an effective in situ resource utilization technology. In spite of these practical applications, the understanding of the combustion properties of metals remains far behind that of the most commonly used fuels such as hydrocarbons. The lack of understanding is due to the many problems unique to metal- oxidizer reactions such as: low-temperature surface oxidation prior to ignition, heterogeneous reactions, very high combustion temperatures, product condensation, high emissivity of products, and multi-phase interactions. Very few analytical models (all neglecting the influence of gravity) have been developed to predict the burning characteristics and the flame structure details. Several experimental studies attempting to validate these models have used small metal particles to recreate gravity-free conditions. The high emissivity of the flames, rapid reaction, and intermittent explosions experienced by these particles have made the gathering of any useful information on burning rates and flame structure very difficult. The use of a reduced gravity environment is needed to clarify some of the complex interactions among the phenomena described above. First, the elimination of the intrusive buoyant flows that plague all combustion phenomena is of paramount importance in metal reactions due to the much higher temperatures reached during combustion. Second, a low-gravity environment is absolutely essential to remove the destructive effect of gravity on the shape of a molten metal droplet in order to study a spherically symmetric condition with large bulk samples. The larger size of the spherical metal droplet and the longer burning times available in reduced gravity extend the spatial and temporal dimensions to permit careful probing of the flame structure and dynamics. Third, the influence of the radiative heat transfer from the solid oxides can be studied more carefully by generating a stagnant spherical shell of condensed products undisturbed by buoyancy.
The intense heat from forest fires can generate explosive deep convective cloud systems that inject pollutants to high altitudes. Both satellite and high-altitude aircraft measurements have documented cases in which these pyrocumulonimbus clouds inject large amounts of smoke well into the stratosphere (Fromm and Servranckx 2003; Jost et al. 2004). This smoke can remain in the stratosphere, be transported large distances, and affect lower stratospheric chemistry. In addition recent in situ measurements in pyrocumulus updrafts have shown that the high concentrations of smoke particles have significant impacts on cloud microphysical properties. Very high droplet number densities result in delayed precipitation and may enhance lightning (Andrew et al. 2004). Presumably, the smoke particles will also lead to changes in the properties of anvil cirrus produces by the deep convection, with resulting influences on cloud radiative forcing. In situ sampling near the tops of mature pyrocumulonimbus is difficult due to the high altitude and violence of the storms. In this study, we use large eddy simulations (LES) with size-resolved microphysics to elucidate physical processes in pyrocumulonimbus clouds.
The Hinode/Extreme-ultraviolet Imaging Spectrometer (EIS) obtained rapid cadence (11.2 s) EUV stare spectra of an M7.3 flare ribbon in AR 12036 on 2014 April 18. Quasi-periodic (P approx. = 75.6 +/- 9.2 s) intensity fluctuations occurred in emission lines of O IV, Mg VI, Mg VII, Si VII, Fe XIV, and Fe XVI during the flare's impulsive rise, and ended when the maximum intensity in Fe XXIII was reached. The profiles of the O IV- Fe XVI lines reveal that they were all redshifted during most of the interval of quasi-periodic intensity fluctuations, while the Fe XXIII profile revealed multiple components including one or two highly blueshifted ones. This indicates that the flare underwent explosive chromospheric evaporation during its impulsive rise. Fluctuations in the relative Doppler velocities were seen, but their amplitudes were too subtle to extract significant quasi-periodicities. RHESSI detected 25-100 keV hard-X-ray sources in the ribbon near the EIS slit's pointing position during the peaks in the EIS intensity fluctuations. The observations are consistent with a series of energy injections into the chromosphere by nonthermal particle beams. Electron densities derived with Fe XIV (4.6 x 10(exp 10) per cu cm) and Mg VII (7.8 x 10(exp 9) per cu cm) average line intensity ratios during the interval of quasi-periodic intensity fluctuations, combined with the radiative loss function of an optically thin plasma, yield radiative cooling times of 32 s at 2.0 x 10(exp 6) K, and 46 s at 6.3 x 10(exp 5) K (about half the quasi-period); assuming Fe XIV's density for Fe XXIII yields a radiative cooling time of 10(exp 3) s (13 times the quasi-period) at 1.4 x 10(exp 7) K.
Understanding large-scale solar eruptions requires detailed investigation of the entire system's evolution, including the magnetic environment enveloping the source region and searches for precursor activity prior to event onset. We combine stereoscopic observations from the Solar Dynamics Observatory (SDO) and STEREO-B spacecraft for several hours before a filament ejection, M1.2-class eruptive flare, and coronal mass ejection (CME) originating in NOAA active region (AR) 11305 on 2011 October 1. Two episodes of significant preeruption coronal dimming that occurred well to the southeast of the ejected filament are identified. The CME subsequently took off with a substantial component of velocity toward the dimming, which became very pronounced during eruption. We used SDO/Helioseismic and Magnetic Imager (HMI) data to reconstruct the magnetic environment of the system and found that it contains a null point near the dimming region. AR 11305 had quite complex connections to nearby ARs 11302 and 11306, as well as to other regions of decayed AR flux. The intensifying and spatially expanding precursor dimming was accompanied by southeastward rising motions of loops toward the null point and northeastward and southwestward motions of loops retracting away. These motions and the dimming are consistent with persistent magnetic reconnection occurring at the null point as it moved upward and southeastward, thereby removing a strapping magnetic field high above AR 11305. Eventually, the filament was ejected explosively toward the null point. We conclude that the breakout model for solar eruptions provides a compelling account of this event. Furthermore, we conjecture that preeruption dimmings may be much more frequent than currently recognized.
RP-1 rocket fuel liquid oxygen and liquid hydrogen-liquid oxygen combination explosion hazard
Convergence of shock waves, generated by underwater electrical explosions of cylindrical wire arrays, between either parabolic or conical bounding walls is investigated. A high-current pulse with a peak of ∼550 kA and rise time of ∼300 ns was applied for the wire array explosion. Strong self-emission from an optical fiber placed at the origin of the implosion was used for estimating the time of flight of the shock wave. 2D hydrodynamic simulations coupled with the equations of state of water and copper showed that the pressure obtained in the vicinity of the implosion is ∼7 times higher in the case of parabolic walls. However, comparison with a spherical wire array explosion showed that the pressure in the implosion vicinity in that case is higher than the pressure in the current experiment with parabolic bounding walls because of strong shock wave reflections from the walls. It is shown that this drawback of the bounding walls can be significantly minimized by optimization of the wire array geometry.
For the first time, the high intensity electron beam modification of electroexplosion composite coatings of Mo Cu, Mo C Cu, W Cu, W C Cu and TiB{sub 2} Cu systems was done. The studies of phase and elemental composition, defective structure conditions of these coatings were carried out. The regimes of electron-beam processing making possible to form the dense, specular luster surface layers having a submicrocrystalline structure were revealed. It was established that electron-beam processing of elecroexplosion spraying of layer of elecroexplosion spraying carried out in the regime of melting results in the formation of structurally and contrationally homogeneous surface layer. Investigation of the effect of electron-beam processing of electroexplosion electroerosion resistant coatings on their tribological properties (wear resistanse and coefficient of friction) and electroerosion resistance was done. It was shown that all the examined costings demonstrate the increase of electroerosion resistance in spark erosion up to 10 times.
We report C, N, and Si isotopic data for 59 highly {sup 13}C-enriched presolar submicron- to micron-sized SiC grains from the Murchison meteorite, including eight putative nova grains (PNGs) and 29 {sup 15}N-rich ({sup 14}N/{sup 15}N ≤ solar) AB grains, and their Mg–Al, S, and Ca–Ti isotope data when available. These 37 grains are enriched in {sup 13}C, {sup 15}N, and {sup 26}Al with the PNGs showing more extreme enhancements. The {sup 15}N-rich AB grains show systematically higher {sup 26}Al and {sup 30}Si excesses than the {sup 14}N-rich AB grains. Thus, we propose to divide the AB grains into groups 1 ({sup 14}N/{sup 15}N < solar) and 2 ({sup 14}N/{sup 15}N ≥ solar). For the first time, we have obtained both S and Ti isotopic data for five AB1 grains and one PNG and found {sup 32}S and/or {sup 50}Ti enhancements. Interestingly, one AB1 grain had the largest {sup 32}S and {sup 50}Ti excesses, strongly suggesting a neutron-capture nucleosynthetic origin of the {sup 32}S excess and thus the initial presence of radiogenic {sup 32}Si ( t {sub 1/2} = 153 years). More importantly, we found that the {sup 15}N and {sup 26}Al excesses of AB1 grains form a trend that extends to the region in the N–Al isotope plot occupied by C2 grains, strongly indicating a common stellar origin for both AB1 and C2 grains. Comparison of supernova models with the AB1 and C2 grain data indicates that these grains came from supernovae that experienced H ingestion into the He/C zones of their progenitors.
In the use of piezo-quartz indicators for high-speed automobile engines, the interpretation of pressure-time diagrams made by an oscillograph offers certain difficulties. On the one hand, the scale of the pressure amplitudes is not always the same under all conditions, while, on the other hand, the atmospheric zero line may be shifted from its correct position in the oscillogram. These facts make necessary to verify the readings of the quartz indicators by direct calibration before and after each series of tests and, on the basis of the results, to determine the scale for the oscillograms.
A comprehensive study is presented of the postexplosion hydrodynamics of the ejecta of SN 1987A encompassing the Rayleigh-Taylor instabilities at the shell interfaces and the dynamical effects of the energy input due to the radioactive decay of Ni-56 and Co-56. The dependence of the hydrodynamical behavior on progenitor structure, initial perturbations, explosion energy, and dimensionality of the numerical simulation is investigated in order to explain the observed high-velocity wings of the iron line of SN 1987A. It is shown that none of these factors leads to the required high-velocity tail of iron. When nickel is artificially premixed in the initial model, it is found that this early mixing has to affect the inner 1.5 solar mass of the ejecta to reproduce the high-velocity wings at a time of 90 d. It is argued that the high-entropy bubble associated with the delayed mechanism is responsible for this premixing by driving convective motions early in the explosion.
Fermi science objectives cover probably everything in high energy astrophysics: How do super massive black holes in Active Galactic Nuclei create powerful jets of material moving at nearly light speed? What are the jets made of? What are the mechanisms that produce Gamma-Ray Burst (GRB) explosions? What is the energy budget? How does the Sun generate high-energy gamma-rays in flares? How do the pulsars operate? How many of them are around and how different are they? What are the unidentified gamma-ray sources found by EGRET? What is the origin of the cosmic rays that pervade the Galaxy? What is the nature of dark matter? Fermi LAT successfully operates on the orbit for more than 2 years and demonstrates excellent performance, which is continuously monitored and calibrated. LAT collected> 100 billion on-orbit triggers