Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Corrosion testing of candidates for the alkaline fuel cell cathode

It is desirable to employ a corrosion screening test for catalyst or support candidates for the fuel cell cathode before entering upon optimization of the candidate or of the catalytic electrode. To this end, corrosion test electrodes, intended for complete immersion and maximum wetting, have been made with 30 to 40 vol. pct Teflon; with perovskites this is about 10 to 15 pct. The candidates were synthesized by methods intended for single-phase product without special emphasis on high surface area, although the substances tested were no coarser than 2 m squared/g. A typical loading was 25 mg/cm sq of the pure substance, usually on gold screen, a few mm squared of which were left bare for contacting. Contact to the gold lead wire was made by welding with a micro-torch or a spot-welder. Corrosion testing consisted of obtaining current-voltage data under flowing inert gas in the potential region for reduction of O2. The electrode was immersed in 30 pct KOH. Observations were made at 20 C and 80 C, and the results compared with data from gold standards. Results with some perovskites, pyrochlores, spinels, and interstitial compounds will be discussed.

Singer, Joseph↗
NASA NTRS2005

Hydrogen-Oxygen PEM Regenerative Fuel Cell Energy Storage System

An introduction to the closed cycle hydrogen-oxygen polymer electrolyte membrane (PEM) regenerative fuel cell (RFC), recently constructed at NASA Glenn Research Center, is presented. Illustrated with explanatory graphics and figures, this report outlines the engineering motivations for the RFC as a solar energy storage device, the system requirements, layout and hardware detail of the RFC unit at NASA Glenn, the construction history, and test experience accumulated to date with this unit.

Bents, David J.↗
NASA NTRS2005

Brazing of Stainless Steels to Yttria Stabilized Zirconia (YSZ) for Solid Oxide Fuel Cells

Recently, there has been a great deal of interest in research, development, and commercialization of solid oxide fuel cells. Joining and sealing are critical issues that will need to be addressed before SOFC's can truly perform as expected. Ceramics and metals can be difficult to join together, especially when the joint must withstand up to 900 C operating temperature of the SOFC's. The goal of the present study is to find the most suitable braze material for joining of yttria stabilized zirconia (YSZ) to stainless steels. A number of commercially available braze materials TiCuSil, TiCuNi, Copper-ABA, Gold-ABA, and Gold-ABA-V have been evaluated. The oxidation behavior of the braze materials and steel substrates in air was also examined through thermogravimetric analysis. The microstructure and composition of the brazed regions have been examined by optical and scanning electron microscopy and EDS analysis. Effect of braze composition and processing conditions on the interfacial microstructure and composition of the joint regions will be presented.

Shpargel, Tarah P.↗
NASA NTRS1986

Develop and test fuel cell powered on site integrated total energy sysems: Phase 3: Full-scale power plant development

A 25-cell stack of the 13 inch x 23 inch cell size (about 4kW) remains on test after 8300 hours, using simulated reformate fuel. A similar stack was previously shut down after 7000 hours on load. These tests have been carried out for the purpose of assessing the durability of fuel cell stack components developed through the end of 1983. A 25kW stack containing 175 cells of the same size and utilizing a technology base representative of the 25-cell stacks has been constructed and is undergoing initial testing. A third 4kW stack is being prepared, and this stack will incorporate several new technology features.

Kaufman, A.↗
NASA NTRS1984

A 37.5-kW point design comparison of the nickel-cadmium battery, bipolar nickel-hydrogen battery, and regenerative hydrogen-oxygen fuel cell energy storage subsystems for low Earth orbit

Nickel-cadmium batteries, bipolar nickel-hydrogen batteries, and regenerative fuel cell storage subsystems were evaluated for use as the storage subsystem in a 37.5 kW power system for space station. Design requirements were set in order to establish a common baseline for comparison purposes. The storage subsystems were compared on the basis of effective energy density, round trip electrical efficiency, total subsystem weight and volume, and life.

Manzo, M. A.↗
NASA NTRS1984

A 37.5-kW point design comparison of the nickel-cadmium battery, bipolar nickel-hydrogen battery, and regenerative hydrogen-oxygen fuel cell energy storage subsystems for low earth orbit

Nickel-cadmium batteries, bipolar nickel-hydrogen batteries, and regenerative fuel cell storage subsystems were evaluated for use as the storage subsystem in a 37.5 kW power system for Space Station. Design requirements were set in order to establish a common baseline for comparison purposes. The storage subsystems were compared on the basis of effective energy density, round trip electrical efficiency, total subsystem weight and volume, and life.

Manzo, M. A.↗
NASA NTRS1990

Catalysts for ultrahigh current density oxygen cathodes for space fuel cell applications

The objective of this research was to identify promising electrocatalyst/support systems for the oxygen cathode in alkaline fuel cells operating at relatively high temperatures, O2 pressures and current densities. A number of materials were prepared, including Pb-Ru and Pb-Ir pyrochlores, RuO2 and Pt-doped RuO2, and lithiated NiO. Several of these were prepared using techniques that had not been previously used to prepare them. Particularly interesting is the use of the alkaline solution technique to prepare the Pt-doped Pb-Ru pyrochlore in high area form. Well-crystallized Pb(2)Ru(2)O(7-y) was used to fabricate high performance O2 cathodes with relatively good stability in room temperature KOH. This material was also found to be stable over a useful potential range at approximately 140 C in concentrated KOH. Other pyrochlores were found to be either unstable (amorphous samples) or the fabrication of the gas-fed electrodes could not be fully optimized during this project period. Future work may be directed at this problem. High area platinum supported on conductive metal oxide supports produced mixed results: small improvements in O2 reduction performance for Pb(2)Ru(2)O(7-y) but a large improvement for Li-doped NiO at room temperature. Nearly reversible behavior was observed for the O2/OH couple for Li-doped NiO at approximately 200 C.

Tryk, D.↗
NASA NTRS2004

Robust Joining Technology for Solid Oxide Fuel Cells Applications

Recently there has been a great deal of interest in research development and commercialization of solid oxide fuel cells (SOFCs). Joining and sealing are critical issues that will need to be addressed before SOFCs can truly perform as expected. Ceramics and metals can be difficult to join together, especially when the joint must withstand up to 900 C operating temperature of the SOFCs. The goal of the present study is to find the most suitable braze material for joining of yttria stabilized zirconia (YSZ) to stainless steel. A number of commercially available braze materials TiCuSil, TiCuNi, Copper-ABA, Gold-ABA and Gold-ABA-V have been evaluated. The oxidation behavior of the braze materials and steel substrates in air was also examined through thermogravimetric analysis. The microstructure and composition of the brazed regions have been examined by optical and scanning electron microscopy and eDS analysis. Effect of braze composition and processing conditions on the interfacial microstructure and composition of the joint regions will be presented.

Shpargel, Tarah P.↗
DOE OSTI2022

Coupled continuum and network model framework to study catalyst layers of polymer electrolyte fuel cells

The nanostructured thin film (NSTF) catalyst layers which have demonstrated high power densities, mass activities, and exceptional metal and support stability can have limited operational robustness due to their thin thickness and the hydrophilicity of the metal-coated nano whiskers. The dispersed nanostructured thin film (dNSTF) catalyst layers have been developed by dispersing the NSTF Pt whiskers with ionomer and carbon support to increase the thickness and hydrophobicity. Continuum and network models (NM) are coupled through boundary conditions to study the polymer electrolyte fuel cell with a dNSTF cathode catalyst layer. The coupled model combines the computational efficiency of the continuum model with the pore-scale information in the dNSTF cathode catalyst layer of the NM. It captures the special morphology of the partially ionomer/water covered cylindrical whiskers, as well as water percolation through the pore structures and their impact on the cell performance. Here we observe optimal ionomer coverage on whiskers to be 0.5, ionomer to carbon ratio to be 0.9 and higher whisker to carbon ratios to be desired.

08 HYDROGEN↗
DOE OSTI2023

Boosting the performances of protonic solid oxide fuel cells for co-production of propylene and electricity from propane by integrating thermo- and electro- catalysis

Protonic solid oxide fuel cells (p-SOFC) integrated with clean thermal energy sources are promising platforms for decarbonized chemical production in addition to power generation, such as on-purpose propylene production from propane dehydrogenation (PDH). The catalytic performance of the conventional nickel-cermet-based anode materials in p-SOFC for propane conversion is restrained by their low active surface area and proneness to coking. In this work, by integration of a highly efficient industry-relevant thermal catalyst PtGa/ZSM-5 for PDH reaction, we demonstrate that both the electrochemical and catalytic performance of the propane-fueled p-SOFC can be effectively enhanced. The PtGa catalyst integrated p-SOFC exhibits a peak power density of 93 mW cm -2 at 600°C, which is greater by about 100% and 50% than that without catalyst or with a perovskite-based (Pr 0.3 Sr 0.7 ) 0.9 Ni 0.1 Ti 0.9 O 3 (PSNT) catalyst layer, respectively. The PDH activity and olefin selectivity of the PtGa catalyst is also significantly higher than that of the PSNT catalyst. In addition, much improved coke tolerance and propylene selectivity (over 90%) compared to the catalyst-free Ni-cermet anode materials were achieved by integrating the industrial catalyst layer. The propane conversion can be further improved by an applied current density, whereas the olefin selectivity is almost unaltered. The excellent performance of the PtGa catalyst integrated p-SOFC is attributed to the high surface area, intrinsically high catalytic activity, selectivity, and anti-coking properties of the catalytic layer for propane conversion. In conclusion, this work provides a general approach and a case study for boosting the performances of p-SOFCs in chemical production by integrating thermo- and electro- catalysis.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Rare Earth Nickelate Electrodes Containing Heavily Doped Ceria for Reversible Solid Oxide Fuel Cells

The electrochemical performance of composite rare-earth nickelate-rare-earth doped ceria oxygen electrodes, with a high level of rare-earth doping in ceria are reported. Additionally, the chemical stability of these compositions is reported at both the sintering (1240 ?C) and operating temperature (800 ?C). Specifically, a lanthanum nickelate La2NiO4+d (LNO) ?? 50 mol% lanthanum doped ceria (LDC50) oxygen electrode and a neodymium nickelate Nd2NiO4+d (NNO) ?? 50 mol% neodymium doped ceria (NDC50) oxygen electrode are tested in solid oxide fuel cell (SOFC) and solid oxide electrolysis cell (SOEC) modes and compared to a composite (La0.75Sr0.25)0.95MnO3±d (LSM)-8 mol% yttria stabilized zirconia (YSZ) electrode. The LNO–LDC50 oxygen electrode reaches a current density which is approximately three times that of the LSM-YSZ electrode in SOFC mode at 0.7 V and approximately two times the LSM-YSZ electrode at 1.2 V in SOEC mode. Similarly the NNONDC50 oxygen electrode reaches a current density which is approximately two times and approximately one and a half times that of LSM-YSZ at 0.7 V and 1.2 V respectively. Oxygen surface exchange results for LNO and NNO are also reported which show different oxygen exchange kinetics during oxidation versus reduction steps.

solid oxide electrolysis, solid oxide fuel cell (S↗
NASA NTRS1989

A fuel cell energy storage system concept for the Space Station Freedom Extravehicular Mobility Unit

An update is given on work to design and build a Fuel Cell Energy Storage System (FCESS) bench-tested unit for the Space Station Freedom Extravehicular Mobility Unit (EMU). Fueled by oxygen and hydride-stored hydrogen, the FCESS is being considered as an alternative to the EMU zinc-silver oxide battery. Superior cycle life and quick recharge are the main attributes of FCESS. The design and performance of a nonventing, 28 V, 34 Ahr system with 7 amp rating are discussed.

Adlhart, Otto J.↗