Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Microstructure evolution, enhanced aging kinetics, and mechanical properties of AA7075 alloy after friction extrusion

In the present study we utilized Friction Extrusion (FE) a solid phase processing technique to produce fully consolidated dense 5 mm rods of AA7075 alloy. The combination of large shear stresses and temperatures at the tool-billet interface during the FE process resulted in the formation of dynamically recrystallized ~2.0 μm equiaxed grains and fine uniformly distributed stable η (MgZn 2 ) precipitates ~25–100 nm in size. Formation of such a microstructure resulted in lower solutionizing temperature and times (flash annealing) as compared to the conventionally extruded counterparts. Here we demonstrate for the first time that the solutionizing times for the T6 heat treatment of AA7075 can be reduced by three times using this FE process. In addition to being an energy efficient process, FE also serves to improve the performance of AA7075 alloys by retaining their strength while enhancing the ductility of the material. The tensile data for samples that were flash annealed and artificially aged after FE processing showed exceptional increase in ultimate tensile strength by over 19% and yield strength by over 59%, compared with an as-FE-processed sample.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Indentation investigation of 304L stainless steel friction stir weld simulated crack repair

Simulated cracks were repaired in 304L stainless steel using low temperature friction stir welding. Indentation studies were carried out to understand the effect of microstructural features on the mechanical property variation across the weld and to measure the size of the weld zones with a quantitative technique. Microhardness and nanoindentation hardness profiles were constructed on a transverse section across the weld. The data obtained were correlated by extrapolating the nanoindentation hardness to greater depths which showed that the nanoindentation hardness closely reflects the microhardness values throughout the weld. Finally, grain size in the stir zone (SZ) was found to vary with the tool temperature which, in turn, alters the nanoindentation modulus variability and higher tool temperature resulted in widening of the SZ.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Three-dimensional microstructure of a friction stir welded magnesium/steel interface characterized via high-energy synchrotron X-rays

Here, the three-dimensional (3D) microstructure of a friction stir assisted scribe technique (FaST) weld interface consisting of AZ31 magnesium (Mg) alloy and zinc (Zn)-coated DP590 steel was analyzed via synchrotron micro-computed tomography (μ-CT), correlated to synchrotron x-ray diffraction, and electron microscopy. Diffraction assessment of the AZ31/Zn-coated DP590 steel interface revealed the presence of several complex Mg–Zn intermetallic phases and differences in crystalline orientation of the Mg phase at the weld interface. The 3D characterization of the synchrotron μ-CT images of the weld interface revealed: (1) the presence of AZ31 weld nugget material with iron (Fe)-rich particles; (2) the presence of a weld layer at the joining interface with Fe-rich particles; (3) the formation of a thin non-uniform layer between the weld layer and the interface of the scribed DP590 material; and (4) the presence of an Fe–Al-rich intermetallic layer and Fe-rich particles at the interface of the scribed DP590 material. This study also performed a detailed analysis of lump-like features seen in the Zn coating layer at the weld interface. A detailed 3D particle analysis of the Fe-rich particles in the AZ31 weld nugget and the weld layer at the weld interface revealed the presence of several types of particle morphologies (i.e., spherical and irregular).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of tool design and pass strategy on defect elimination and uniform, enhanced tensile properties of friction stir processed high-pressure die-cast A380 alloy

This work reports implementation of friction stir processing (FSP) to locally modify microstructure and create a defect-free processing zone with the aid of different tool designs and altering the passing strategy for two different process parameter combinations. Here, FSP is applied on high pressure die-cast (HPDC) A380 alloy, a widely used Al-Si alloy fabricated in the die casting sector for automotive and aerospace applications. However, the presence of gas and shrinkage porosity, brittle needle-shaped Fe-containing ß-FeSiAl 5 intermetallic compounds, Al-dendrites, coarse and acicular silicon particles, and large second-phase particulates have a detrimental influence on the uniformity of tensile properties across the thickness direction of an HPDC plate. FSP is able to eliminate porosity, refine microstructure and improve tensile properties. An FSP tool design and a passing strategy are identified for the best microstructure consolidation and uniform enhanced tensile properties. This study noted the importance of tool features such as scroll design and flats on tool pin and multiple pass orientation strategy to find best combination of defect-free refined microstructure and uniform tensile strength and ductility across the processing zone of HPDC Al alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Friction stir processing on a strontium modified, thin-wall, vacuum-assisted high-pressure die-cast Aural-5 alloy to improve tensile and fatigue performance

Here, this study explores the application of friction stir processing (FSP) to enhance the material properties of Sr-modified Aural-5 alloy, with a focus on improved tensile and fatigue properties. Aural-5 is a well-known vacuum-assisted high-pressure die-cast (HPDC) Al-Si7-Mg alloy used in the automotive industry to reduce vehicle weight, enhance fuel efficiency, and lower carbon emissions. This alloy modifies its material chemistry with Sr for fine fibrous networks of eutectic silicon and manganese (Mn) to reduce die soldering. It has significantly less iron (Fe) content resulting in the elimination of detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. The initial microstructure of as-received HPDC Aural-5 exhibits shrinkage porosity in the middle section, a dendritic microstructure with fibrous Al-Si eutectic colonies, a shear-band structure beneath the die-wall, large dendritic externally solidified crystals (ESCs), needle-shaped Mg 2 Si phase and significant second-phase particulates. Some of those microstructural features, such as porosity, ESCs, needle-shaped Mg 2 Si phase, and large second-phase particles, serve as initiation sites for cracks under mechanical loading, resulting in adverse effects on tensile properties, particularly ductility. FSP effectively transforms the microstructure into a wrought configuration with uniform particle distribution by eliminating porosity and disintegrating dendrites, eutectic colonies, ESCs, second-phase particles, and shear-band structures. FSP-driven microstructure modification enhances yield strength and tensile ductility by ~30% and ~35%, respectively. The fatigue life of the material in a bending mode configuration (stress ratio R = 0.1) after FSP exhibits enhancements ranging from 2.0 to 3.9 times that of the original HPDC Aural-5 alloy, depending on the applied stress level.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Friction surface layer deposition of triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high entropy alloy: Process optimization and microstructural evolution

A high-strength Co-free triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high-entropy alloy (HEA) was successfully fabricated using Friction Surface Layer Deposition (FSLD), a bulk manufacturing method. Multiple single-layer deposits were produced by varying forging force (F) and traverse speeds (T r ) to optimize the process parameters. The optimized conditions (F = 40 kN & T r = 200 mm/min) were then applied to manufacture a scaled-up multi-layer specimen. The initial microstructure of the HEA consisted of coarse grains of the soft FCC-phase, long columnar dendrites of the hard BCC-phase, and small precipitates of the harder B2-phase within the BCC-dendrites. During FSLD, the FCC-matrix underwent continuous dynamic recrystallization due to high-temperature severe plastic deformation, forming finer equiaxed grains. Simultaneously, the BCC-dendrites fractured into smaller fragments, some of which experienced partial growth and coarsening under applied stress, resulting in an hourglass morphology. In contrast, the small B2-precipitates within the BCC-fragments dissolved during the elevated temperatures of FSLD and reprecipitated as substantially finer precipitates during continuous cooling post-FSLD. Additionally, the orientation relationships between the FCC and BCC/B2 phases were completely destroyed by the severe thermoplastic deformation inherent to FSLD. The microstructural refinements led to a substantial improvement in hardness from 177 HV to 283 HV, driven by Hall-Petch strengthening. The increased number of interfaces, including coherent BCC-B2 interfaces, potentially enhances the sink strength and radiation tolerance of the HEA, making it a promising candidate for nuclear applications. In conclusion, this study also highlights FSLD as a versatile technique for achieving tunable properties in HEAs, with detailed schematics illustrating the complex mechanisms of phase transformations during processing.

Additive Manufacturing↗
DOE OSTI2025

Boron Nitride-Driven Strengthening of Aluminum Composites via Friction Stir Processing

Friction stir welding and processing (FSW/P) has emerged as an effective solid-state joining technique for fabricating metal matrix composites (MMCs), offering improved mechanical properties through refined microstructural evolution. In this study, an aluminum-boron nitride nanoparticle (Al-BNNP) composite was synthesized via FSW, and its indentation-based mechanical properties were systematically evaluated. Microhardness mapping across the weld cross-section revealed a progressive increase in hardness toward the stir zone (SZ), attributed to severe plastic deformation, dynamic recrystallization (DRX), and the reinforcing effect of BNNPs. Profilometry-based indentation plastometry (PIP) inferred yield strength (YS) demonstrates a 47.8% increase compared to the base metal (BM) and a 75% improvement compared to FSP pure aluminum reported in literature. This enhancement is attributed to strengthening mechanisms, including grain boundary pinning, load transfer, and increased dislocation density. The strain rate sensitivity (SRS) measurements at the nanoscale demonstrated a substantial decrease in the SZ, correlated with ultrafine grain structures and strong BNNP-matrix interactions. Activation volume analysis revealed a significant reduction in the SZ, suggesting that dislocation motion is increasingly restricted by dislocation-dislocation and dislocation-particle interactions. These findings suggest that incorporating BNNPs in FSW/P enables tailoring the microstructure without thermal degradation of the secondary particles, thereby significantly enhancing the mechanical performance of aluminum composites, particularly for structural applications in aerospace and automotive industries.

Aluminum↗
DOE OSTI2026

Use of friction stir processing to synthesize nanocrystalline, grain boundary segregating Fe-Ti alloys

Grain boundary segregating alloys, a class of alloys designed such that nanocrystalline grain sizes are thermodynamically stabilized by the presence of high segregation energy solutes at the grain boundaries, are typically produced through geometrically limited processing techniques such as equal channel angular extrusion or thin film sputtering. Here, this study explores the use of friction stir processing (FSP) as a novel means of studying and producing these alloys using a test system of Fe-6at%Ti. Spot FSPs with a range of processing parameter sets were produced on bulk, coarse grained bars of material and optimal parameters were identified. Microscopy identified a range of processed materials which achieved nanocrystalline grains on the order of 100 nm, delineating a critical window of processing parameters which limit heat input while inducing sufficient plastic deformation for grain refinement. The finest grained nanocrystalline Fe-Ti achieved a hardness of 7.68 GPa, a significant increase in hardness over pure Fe with a similar microstructure due to increased dislocation density from FSP as well as several strengthening mechanisms produced through the presence and segregation of Ti. These results demonstrated the feasibility of using FSP to produce nanocrystalline grain boundary segregating alloys.

Fe alloys↗
DOE OSTI2026

Understanding the effect of friction stir processing on electrical steel: Microstructural changes and mechanical transformations

Raising Si beyond 3.5 wt% reduces core loss but embrittles electrical steels, constraining processing and application. Here we assess friction stir processing (FSP) as a solid‑state route to enable Fe–4.0 wt% Si with improved mechanical performance. Temperature‑controlled FSP with a PcBN tool produced a defect‑free processed zone. SEM/EBSD revealed dynamic recrystallization and grain refinement from an average 110 μm in the base material to ∼20 μm in the processed region, with ∼ 80% of grains < 40 μm and a reduction in high‑angle boundary fraction to ∼65% (vs >85% in the base). Comparative mechanical property analysis shows a moderate increase in yield strength in FSP samples relative to the base material, with a significant improvement in ductility (∼35–50%). Post‑fracture EBSD identified 60° twin boundaries in the base while sub-grain formation with elevated KAM in the FSP sample. Fractography revealed a shift from quasi‑cleavage in the Base-faceted planes with river patterns, steps, and occasional secondary cracks—to ductile micro void coalescence after FSP. Following FSP, the material retains soft‑magnetic behavior, with modest shifts in saturation magnetization consistent with grain refinement and stored strain, accompanied by a clear gain in formability. These results indicate that FSP provides a viable route to deploy higher‑Si electrical steels with concurrent gains in strength and ductility.

Electrical steel↗
DOE OSTI2022

Porosity evolution during heating of copper made from powder by friction extrusion

Here, friction extrusion was used to compact and extrude solid copper rod from feedstock powders. Following extrusion, considerable porosity was observed throughout the extrudate cross section due to the entrained porosity in the feedstock material and the extrusion process. The thermal stability of the extrudate was investigated via a series of heat treatments. Porosity evolution exhibited three distinct stages—an unchanged plateau (0°C–300°C) followed by an abrupt increase (400°C–500°C) and ultimately a reduction, as the temperature increases (>500°C). The peak porosity measured was ~25%. The underlying driving force for pore evolution is described as the competition between the internal pore pressure, material strength, and sintering kinetics, as a function of temperature. The observed porosity evolution and driving force are not expected to be limited to copper. Thus, this manuscript reveals an important consideration regarding elevated-temperature thermal stability as advanced manufacturing methods involving direct powder extrusion are explored.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Force reduction of friction stir welding and processing of steel

Friction stir welding and processing (FSW&P) is considered as a new fabrication method for canisters and repair of existing dry cask storage system canisters (generally made of austenitic stainless steel). Low heat input compared to fusion joining processes and grain refinement associated with low-temperature FSW&P result in a material with improved mechanical properties and equivalent generalized corrosion performance relative to the base metal. But FSW&P of austenitic stainless steel requires significant tool forge axis force to produce a weld (or a run). Exploratory runs utilizing forge axis force control were conducted to investigate the minimum force required to achieve defect-free runs. The correlation between forge axis force and resultant plunge depth was also investigated. Furthermore, detailed microstructural characterization was conducted to display the microstructural variation within the nugget zone.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tribocatalytically-activated formation of protective friction and wear reducing carbon coatings from alkane environment

Minimizing the wear of the surfaces exposed to mechanical shear stresses is a critical challenge for maximizing the lifespan of rotary mechanical parts. In this study, we have discovered the anti-wear capability of a series of metal nitride-copper nanocomposite coatings tested in a liquid hydrocarbon environment. The results indicate substantial reduction of the wear in comparison to the uncoated steel substrate. Analysis of the wear tracks indicates the formation of carbon-based protective films directly at the sliding interface during the tribological tests. Raman spectroscopy mapping of the wear track suggests the amorphous carbon (a-C) nature of the formed tribofilm. Further analysis of the tribocatalytic activity of the best coating candidate, MoN-Cu, as a function of load (0.25–1 N) and temperature (25 °C and 50 °C) was performed in three alkane solutions, decane, dodecane, and hexadecane. Results indicated that elevated temperature and high contact pressure lead to different tribological characteristics of the coating tested in different environments. The elemental energy dispersive x-ray spectroscopy analysis and Raman analysis revealed formation of the amorphous carbon film that facilitates easy shearing at the contact interface thus enabling more stable friction behavior and lower wear of the tribocatalytic coating. These findings provide new insights into the tribocatalysis mechanism that enables the formation of zero-wear coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Curvature effect on tearing modes in presence of neoclassical friction

Neoclassical physics (here associated to the poloidal variation of the magnetic field strength along field lines in a tokamak) is well known for driving self-generated plasma current and nonlinear magnetic islands associated to it in high performance, ITER relevant plasma discharges. It is demonstrated that the neoclassical friction between a magnetic perturbation and plasma flow already impacts magnetic islands in the linear regime, by inducing a weakening of curvature stabilization for tearing modes. This conclusion holds in particular for regimes where convection is influencing the pressure dynamics, as shown using a simple analytical model and confirmed in full Magneto-Hydro-Dynamics simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2014

Single-friction-surface triboelectric generator with human body conduit

We present a transparent single-friction-surface triboelectric generator (STEG) employing human body as the conduit, making the applications of STEG in portable electronics much more practical and leading to a significant output improvement. The STEG with micro-patterned polydimethylsiloxane surface achieved an output voltage of over 200 V with a current density of 4.7 μA/cm{sup 2}. With human body conduit, the output current increased by 39% and the amount of charge that transferred increased by 34% compared to the results with grounded electrode. A larger increment of 210% and 81% was obtained in the case of STEG with a large-size flat polyethylene terephthalate surface.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Measurement of local internal friction in metallic glasses

Atomic force acoustic microscopy (AFAM), an advanced scanning probe microscopy technique, has been used to measure local elastic properties with a spatial resolution given by the tip-sample contact radius. AFAM is based on inducing out-of-plane vibrations in the specimen. The vibrations are sensed by the AFM cantilever from by the photodiode signal when its tip is in contact with the material under test. To measure local damping, the inverse quality factor Q{sup −1} of the resonance curve is usually evaluated. Here, from the contact-resonance spectra obtained, we determine the real and imaginary part of the contact stiffness k* and from these two quantities the local damping factor Q{sub loc}{sup −1} is obtained which is proportional to the imaginary part γ of the contact stiffness. The evaluation of the data is based on the cantilever's mass distribution with damped flexural modes and not on an effective point-mass approximation for the cantilever’s motion. The given equation is simple to use and has been employed to study the local Q{sub loc}{sup −1} of amorphous PdCuSi metallic glass and its crystalline counterpart as a function of position of the AFM tip on the surface. The width of the distribution changes dramatically from the amorphous to the crystalline state as expected from the consequences of the potential-energy landscape picture. The center value of the distribution curve for Q{sub loc}{sup −1} coincides very well with published data, based on global ultrasonic or internal friction measurements. This is compared to Q{sub loc}{sup −1} measured in crystalline SrTiO{sub 3}, which exhibits a narrow distribution, as expected.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Eutectic structures in friction spot welding joint of aluminum alloy to copper

A dissimilar joint of AA5083 Al alloy and copper was produced by friction spot welding. The Al-MgCuAl{sub 2} eutectic in both coupled and divorced manners were found in the weld. At a relatively high temperature, mass transport of Cu due to plastic deformation, material flow, and atomic diffusion, combined with the alloy system of AA5083 are responsible for the ternary eutectic melting.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Controlling the number of graphene sheets exfoliated from graphite by designed normal loading and frictional motion

We use molecular dynamics to study the exfoliation of patterned nanometer-sized graphite under various normal loading conditions for friction-induced exfoliation. Using highly ordered pyrolytic graphite (HOPG) as well as both amorphous and crystalline SiO{sub 2} substrate as example systems, we show that the exfoliation process is attributed to the corrugation of the HOPG surface and the atomistic roughness of the substrate when they contact under normal loading. The critical normal strain, at which the exfoliation occurs, is higher on a crystalline substrate than on an amorphous substrate. This effect is related to the atomistic flatness and stiffness of the crystalline surface. We observe that an increase of the van der Waals interaction between the graphite and the substrate results in a decrease of the critical normal strain for exfoliation. We find that the magnitude of the normal strain can effectively control the number of exfoliated graphene layers. This mechanism suggests a promising approach of applying designed normal loading while sliding to pattern controlled number of graphene layers or other two-dimensional materials on a substrate surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Friction stir processing on carbon steel

Friction stir processing of medium carbon steel samples has been carried out using a milling machine and tools made of cemented tungsten carbide. Samples have been machined from 40 and 40X steels. The tools have been made in the shape of 5×5×1.5 mm and 3×3×1.5 mm tetrahedrons. The microstructure of stirred zone has been obtained using the smaller tool and consists of fine recrystallized 2-3 μm grains, whereas the larger tool has produced the 'onion-like' structures comprising hard quenched 'white' 500-600 MPa layers with 300-350 MPa interlayers of bainite needles. The mean values of wear intensity obtained after measuring the wear scar width were 0.02 mm/m and 0.001 mm/m for non-processed and processed samples, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗