Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flight Test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Boundary-Layer-Transition and Heat-Transfer Measurements from Flight Tests of Blunt and Sharp 50 Degree Cones at Mach Numbers from 1.7 to 4.7

Boundary-layer-transition and heat-transfer measurements were obtained from flight tests of blunt and sharp cones having apex angles of 50 deg. The test Mach number range was from 1.7 to 4.7, corresponding to free-stream Reynolds numbers, based on cone base diameter, of 18. 3 x 10(exp 6) and 32.1 x 10(exp 6), respectively. Transition on both models occurred at a local Reynolds number of 1 x 10(exp 6) to 2 X 10(exp 6) based on distance from the stagnation point. Transition Reynolds numbers based on momentum thickness were between 320 and 380 for the blunt cone. The model surface roughness was 25 rms microinches or greater. Turbulent heat transfer to the conical surface of the blunt cone at a Mach number of 4 was 30 percent less than that to the surface of the sharp cone. Available theories predicted heat-transfer coefficients reasonably well for the fully laminar or turbulent flow conditions.

BLUNT BODY↗
NASA NTRS1978

Helicopter external noise prediction and correlation with flight test

Mathematical analysis procedures for predicting the main and tail rotor rotational and broadband noise are presented. The aerodynamic and acoustical data from Operational Loads Survey (OLS) flight program are used for validating the analysis and noise prediction methodology. For the long method of rotational noise prediction, the spanwise, chordwise, and azimuthwise airloading is used. In the short method, the airloads are assumed to be concentrated at a single spanwise station and for higher harmonics an airloading harmonic exponent of 2.0 is assumed. For the same flight condition, the predictions from long and short methods of rotational noise prediction are compared with the flight test results. The short method correlates as well or better than the long method.

Gupta, B. P.↗
NASA NTRS1988

Correlation of SA349/2 Helicopter Flight Test Data with a Comprehensive Rotorcraft Model

A comprehensive rotorcraft analysis model, CAMRAD, was used to predict blade aerodynamic and structural loads and performance for comparison with flight test data. The data were obtained from an SA349/2 helicopter with an advanced geometry rotor. Sensitivity of the correlation to wake geometry, blade dynamics, and blade aerodynamic effects was investigated. Blade chordwise pressure coefficients were predicted for the transonic regimes near the blade tip using the model coupled with two finite-difference codes.

Yamauchi, Gloria K.↗
NASA NTRS2012

Simulation and Flight Test Capability for Testing Prototype Sense and Avoid System Elements

NASA Langley Research Center (LaRC) and The MITRE Corporation (MITRE) have developed, and successfully demonstrated, an integrated simulation-to-flight capability for evaluating sense and avoid (SAA) system elements. This integrated capability consists of a MITRE developed fast-time computer simulation for evaluating SAA algorithms, and a NASA LaRC surrogate unmanned aircraft system (UAS) equipped to support hardware and software in-the-loop evaluation of SAA system elements (e.g., algorithms, sensors, architecture, communications, autonomous systems), concepts, and procedures. The fast-time computer simulation subjects algorithms to simulated flight encounters/ conditions and generates a fitness report that records strengths, weaknesses, and overall performance. Reviewed algorithms (and their fitness report) are then transferred to NASA LaRC where additional (joint) airworthiness evaluations are performed on the candidate SAA system-element configurations, concepts, and/or procedures of interest; software and hardware components are integrated into the Surrogate UAS research systems; and flight safety and mission planning activities are completed. Onboard the Surrogate UAS, candidate SAA system element configurations, concepts, and/or procedures are subjected to flight evaluations and in-flight performance is monitored. The Surrogate UAS, which can be controlled remotely via generic Ground Station uplink or automatically via onboard systems, operates with a NASA Safety Pilot/Pilot in Command onboard to permit safe operations in mixed airspace with manned aircraft. An end-to-end demonstration of a typical application of the capability was performed in non-exclusionary airspace in October 2011; additional research, development, flight testing, and evaluation efforts using this integrated capability are planned throughout fiscal year 2012 and 2013.

Howell, Charles T.↗
NASA NTRS2017

Aeroelastic Modeling of X-56A Stiff-Wing Configuration Flight Test Data

Aeroelastic stability and control derivatives for the X-56A Multi-Utility Technology Testbed (MUTT), in the stiff-wing configuration, were estimated from flight test data using the output-error method. Practical aspects of the analysis are discussed. The orthogonal phase-optimized multisine inputs provided excellent data information for aeroelastic modeling. Consistent parameter estimates were determined using output error in both the frequency and time domains. The frequency domain analysis converged faster and was less sensitive to starting values for the model parameters, which was useful for determining the aeroelastic model structure and obtaining starting values for the time domain analysis. Including a modal description of the structure from a finite element model reduced the complexity of the estimation problem and improved the modeling results. Effects of reducing the model order on the short period stability and control derivatives were investigated.

Grauer, Jared A.↗
NASA NTRSDate not supplied

UAM Noise Working Group Meeting Subgroup 2: Ground & Flight Testing

The Urban Air Mobility Noise Working Group (UNWG) Sub-Group 2 is tasked with development of a research measurement protocol for UAM vehicle ground and flight testing to determine the impact of representative vehicles on community noise. This briefing is a bi-annual update to the UNWG participants at large regarding the activities of SG2, specifically the status of the group’s measurement protocols document under development.

Urban Air Mobility↗
NASA NTRS1958

The Effects of Longitudinal Control-System Dynamics on Pilot Opinion and Response Characteristics as Determined from Flight Tests and from Ground Simulator Studies

The results of a fixed-base simulator study of the effects of variable longitudinal control-system dynamics on pilot opinion are presented and compared with flight-test data. The control-system variables considered in this investigation included stick force per g, time constant, and dead-band, or stabilizer breakout force. In general, the fairly good correlation between flight and simulator results for two pilots demonstrates the validity of fixed-base simulator studies which are designed to complement and supplement flight studies and serve as a guide in control-system preliminary design. However, in the investigation of certain problem areas (e.g., sensitive control-system configurations associated with pilot- induced oscillations in flight), fixed-base simulator results did not predict the occurrence of an instability, although the pilots noted the system was extremely sensitive and unsatisfactory. If it is desired to predict pilot-induced-oscillation tendencies, tests in moving-base simulators may be required. It was found possible to represent the human pilot by a linear pilot analog for the tracking task assumed in the present study. The criterion used to adjust the pilot analog was the root-mean-square tracking error of one of the human pilots on the fixed-base simulator. Matching the tracking error of the pilot analog to that of the human pilot gave an approximation to the variation of human-pilot behavior over a range of control-system dynamics. Results of the pilot-analog study indicated that both for optimized control-system dynamics (for poor airplane dynamics) and for a region of good airplane dynamics, the pilot response characteristics are approximately the same.

Sadoff, Melvin↗
NASA NTRSDate not supplied

LOFTID (Low-Earth Orbit Flight Test of an Inflatable Decelerator) PASS (Payload Adapter Separation System) Design & Qualification

On November 10, 2022, NASA, in partnership with United Launch Alliance (ULA), launched Low-earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) as a secondary payload on an Atlas V Centaur out of the Vandenburg Space Force Base (VSFB). After successfully delivering the primary payload, Joint Polar Satellite System-2 (JPSS-2), to a sun synchronous trajectory, the Centaur upper stage reoriented LOFTID onto the desired reentry trajectory. After conducting a de-orbit burn to enter the atmosphere the Payload Adaptor was ejected to expose the packed LOFTID vehicle. The LOFTID Hypersonic Inflatable Aerodynamic Decelerator (HIAD) was deployed and inflated. The Centaur pointed LOFTID to the desired entry attitude and spun the vehicle up to roughly three rpm before separating the reentry vehicle over the Middle East. The LOFTID vehicle flew freely before reentering the atmosphere over Alaska at >8km/sec and decelerating as designed. LOFTID demonstrated stable flight from hypersonic entry through subsonic parachute deployment. LOFTID was enabled by a mission-unique Payload Adapter Separation System (PASS) which separated the Payload Adapter prior to the start of the LOFTID flight demonstration, allowing the launch vehicle to accommodate a superstack of two independent, similarly sized payloads. This paper will discuss the design, development, and qualification effort of the LOFTID PASS.

Sean M Hancock↗
NASA NTRS1974

Flight test results of an automatic support system on board a YF-12A airplane

An automatic support system concept that isolated faults in an existing nonavionics subsystem was flight tested up to a Mach number of 3. The adaptation of the automated support concept to an existing system (the jet engine automatic inlet control system) caused most of the problems one would expect to encounter in other applications. These problems and their solutions are discussed. Criteria for integrating automatic support into the initial design of new subsystems are included in the paper. Cost effectiveness resulted from both the low maintenance of the automated system and the man-hour saving resulting from the real time diagnosis of the monitored subsystem.

Love, J. E.↗
NASA NTRS1990

A flight test investigation of certification requirements for laminar-flow general aviation airplanes

A modified T210R general aviation aircraft incorporating natural laminar flow (NLF) technology has been subjected to flight tests in order to evaluate its stability and control characteristics. Attention is given to this aircraft's ability to meet certification requirements with significant NLF, as well as with the boundary-layer transition fixed near the leading edge. It is established that the large regions of NLF achieved yielded a significant cruise performance enhancement; loss of laminar flow did not result in significant changes in the stability and control characteristics of the aircraft. FAR Part 23 certification requirements were met.

Manuel, Gregory S.↗
NASA NTRS1970

High Altitude Flight Test of a 40-Foot Diameter (12.2 meter) Ringsail Parachute at Deployment Mach Number of 2.95

A 40-foot-nominal-diameter (12.2-meter) modified ringsail parachute was flight tested as part of the NASA Supersonic High Altitude Parachute Experiment (SHAPE) program. The 41-pound (18.6-kg) test parachute system was deployed from a 239.5-pound (108.6-kg) instrumented payload by means of a deployment mortar when the payload was at an altitude of 171,400 feet (52.3 km), a Mach number of 2.95, and a free-stream dynamic pressure of 9.2 lb/sq ft (440 N/m(exp 2)). The parachute deployed properly, suspension line stretch occurring 0.54 second after mortar firing with a resulting snatch-force loading of 932 pounds (4146 newtons). The maximum loading due to parachute opening was 5162 pounds (22 962 newtons) at 1.29 seconds after mortar firing. The first near full inflation of the canopy at 1.25 seconds after mortar firing was followed immediately by a partial collapse and subsequent oscillations of frontal area until the system had decelerated to a Mach number of about 1.5. The parachute then attained a shape that provided full drag area. During the supersonic part of the test, the average axial-force coefficient varied from a minimum of about 0.24 at a Mach number of 2.7 to a maximum of 0.54 at a Mach number of 1.1. During descent under subsonic conditions, the average effective drag coefficient was 0.62 and parachute-payload oscillation angles averaged about &loo with excursions to +/-20 degrees. The recovered parachute was found to have slight damage in the vent area caused by the attached deployment bag and mortar lid.

TESTS↗
NASA NTRS1991

Flight tests with a data link used for air traffic control information exchange

Previous studies showed that air traffic control (ATC) message exchange with a data link offers the potential benefits of increased airspace system safety and efficiency. To accomplish these benefits, data link can be used to reduce communication errors and relieve overloaded ATC voice radio frequencies, which hamper efficient message exchange during peak traffic periods. Flight tests with commercial airline pilots as test subjects were conducted in the NASA Transport Systems Research Vehicle Boeing 737 airplane to contrast flight operations that used current voice communications with flight operations that used data link to transmit both strategic and tactical ATC clearances during a typical commercial airflight from takeoff to landing. The results of these tests that used data link as the primary communication source with ATC showed flight crew acceptance, a perceived reduction in crew work load, and a reduction in crew communication errors.

Knox, Charles E.↗
NASA NTRS1997

Development of the Flight Test Telemetry System for Clipper Graham: A New Way to do Business

Since the beginning of NASA, there has been one way to do business. To procedure flight hardware you did things a certain way, to monitor contracts you did things a certain way and to support tests you did things a certain way. When the Delta Clipper Experimental (DC-X) space flight test vehicle was being upgraded (to the DC-XA, later called the Clipper Graham), the opportunity to change the way NASA did business presented itself The development of a flight test telemetry system (FTTS) for the Clipper Graham presented the perfect opportunity to change the way NASA did business. This paper will discuss the differences from the old way to the new way of doing business during the development of the FTTS from the conceptual stage thru the flight stages. The major focus will be the pulse code modulation system of the FTTS. Topics that will be discussed are working with procurement, working with contractors and subcontractors, supporting ground and flight testing and lessons learned.

Blue, Lisa↗
NASA NTRS1972

Flight test of carbon-phenolic on a spacecraft launched by the pacemaker vehicle system

Carbon-phenolic material consisting of 50 percent carbon fibers and 50 percent phenolic resin was flight tested on a recoverable spacecraft launched by the Pacemaker vehicle system. The heat shield of the spacecraft was fabricated so that the carbon fibers in the ablator material had different orientations over several areas of the spacecraft. The environment in which the spacecraft was tested produced heating rates on the hemispherical nose up to 13.6 MW/sq m (1200 Btu/sq ft/sec) and stagnation-point pressures up to 1.27 MN/sq m (12.5 atm). The experimental results are presented. Due to high heating rates and possible spallation and mechanical char removal the greatest mass loss occurred in the nose region. Essentially uniform surface recession and char thickness were observed on the conical section of the spacecraft. A comparison of measured heating rates with computed turbulent and laminar heating rates, as well as measurements of sound-pressure fluctuations in the boundary layer obtained with acoustic sensors, indicated that the boundary layer underwent transition. The acoustic sensor provides an interesting new data form for the general study of boundary-layer transition for free-flight investigations.

Walton, T. E., Jr.↗
NASA NTRS1978

Initial flight test of a Loran-C receiver/data collection system

Development of a low cost Loran C receiver for general aviation use is discussed. The preparation and procedure of a flight test conducted with a receiver design which utilizes a phase locked loop oscillator to track the Loran C signals is described. It is indicated that such a receiver is a viable alternative for future work in developing a low cost Loran-C navigator.

Fischer, J. P.↗
NASA NTRS1980

Dynamics stability derivatives of space shuttle orbiter obtained from wind-tunnel and approach and landing flight tests

A comparison was made between ground facility measurements, the aerodynamic design data book values, and the dynamic damping derivatives extracted from the space shuttle orbiter approach and landing flight tests. The comparison covers an angle of attack range from 2 deg to 10 deg at subsonic Mach numbers. The parameters of pitch, yaw, and roll damping, as well as the yawing moment due to rolling velocity and rolling moment due to yawing velocity are compared.

Freeman, D. C., Jr.↗