Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELONGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Gelatin/Gelatinized Sago Starch Biomembranes as a Drug Delivery System Using Rubber Latex as Plasticizer

Preparation and properties of gelatin and gelatin/gelatinized sago starch biomembranes as a drug delivery system are presented. Deproteinized natural rubber latex (DNRL) was chosen to blend as a plasticizer in biomembranes due to its elasticity. The opaque biomembranes were formed, and the effect of DNRL amounts (10–50 part per hundred of gelatin; phg) on mechanical properties of biomembranes was investigated. It was discovered that increasing the amounts of DNRL could decrease the brittleness of biomembranes. However, these DNRL blended biomembranes still swelled, dissolved in water, and eroded within 2 h. The 50 phg DNRL was further chosen for biomembrane preparations. Then, the 5–30 phg gelatinized sago starch which was prepared in-house was added. These gelatin/gelatinized sago starch biomembranes were homogenous and opaque. They portrayed good water uptake properties, and the highest values occurred in 20–30 min, then these biomembranes eroded slowly. Increasing the amounts of sago starch in biomembranes raised the water uptake rates but reduced the erosion properties. Biomembranes with and without starch blends showed the same tensile strengths. Their elongations at break increased when the amounts of starch were raised but still were lower than that of gelatin/DNRL biomembranes. The morphology, scanning electron microscopy, atomic force electron microscopy, Fourier transform infrared spectroscopy, differential scanning calorimeter, and X-ray diffractometer confirmed the compatibility of ingredients in biomembranes. Lidocaine and its hydrochloride salt were successfully incorporated in these biomembranes with good properties. The drug release and permeation of biomembrane showed good drug controlled release and were able to permeate through the pig skin.

36 MATERIALS SCIENCE↗

The Taste of Waste: The Edge of Eggshell Over Calcium Carbonate in Acrylonitrile Butadiene Rubber

Rubber technology experiences a new age by the use of biowaste or natural fillers. In this regard, taking properties of reinforcing agents from biowaste fillers remains as the challenging matter. Chicken eggshell (ES) biowaste has recently been introduced to substitute calcium carbonate (CaCO{sub 3}) duo to its superior properties and low price. In this work, composites based on acrylonitrile butadiene rubber (NBR) reinforced with ES and CaCO{sub 3} microfillers at various loading levels were prepared and characterized. To improve the interactions between fillers and the NBR matrix, ES and CaCO{sub 3} were surface-functionalized using a terpolymer, namely poly(vinyl 2-pyrrolidone-co-maleic acid-co-acrylic acid). Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) were used to characterize the modified fillers. The incorporation of the functionalized fillers resulted in a significant rise in the maximum torque according to the rheometric measurements. The Young’s modulus of the ES-based and CaCO{sub 3}-based compounds showed a mild improvement over a wide range of filler contents. The elongation at break of the NBR composites, however, was dependent on the filler content. This work provides exciting opportunities for the design of novel and innovative coupling agents to be used in rubber applications.

36 MATERIALS SCIENCE↗

Properties and Biodegradation of Thermoplastic Starch Obtained from Grafted Starches with Poly(lactic acid)

Properties and biodegradation of thermoplastic starch obtained using granular starches grafted with poly(lactic acid) (St-g-PLA) were studied. The grafting of PLA on the starch granule was verified by the emergence of the carbonyl group in the FTIR spectra and the higher diameter of the grafted starch granule. Thermoplastic starch from ungrafted granular starch (TPS) and grafted granular starch (TPGS) were obtained by mixing ungrafted or grafted starch with water, glycerol or sorbitol in a mixer. TPS and TPGS behave as plastic materials, and their mechanical properties depend on the type of plasticizer used. Materials with glycerol as the plasticizer exhibited less rigidity than the materials obtained using sorbitol. The presence of starch-g-PLA results in an increase in the elongation of the thermoplastic material. TPS and TPGS were hydrolysed by amylolytic enzymes in short-time periods compared to granular PLA-grafted starches.

36 MATERIALS SCIENCE↗

Environmentally Friendly Novel Maleated Poly(vinyl alcohol) Grafted 1, 4-Butanediol Modified with Biopolymer for Encapsulation of Capsaicin

Nowadays, hydrogels are widely used in many fields, for instance as biosensors, in tissue engineering and in agriculture due to their high swelling behavior in water and their softness. The objective of this work was to study the preparation and physical properties of maleated poly (vinyl alcohol) (PVAM)-graft-butanediol (BDO) (PVAM-graft-BDO) using K{sub 2}S{sub 2}O{sub 8} as an initiator. The highest grafting efficiency of 92% was found at 7:3 PVAM-graft-BDO. The swelling behavior of the PVAM-graft-BDO increased with an increasing BDO content. The highest swelling ratio of the PVAM-graft-BDO of 250% was found at 7:3 PVAM:BDO. Moreover, the maximum tensile strength of the PVAM-graft-BDO was observed at 9:1 PVAM:BDO. The elongation at break of the PVAM-graft-BDO was improved by the addition of natural rubber-graft-cassava starch (NS). The PVAM-graft-BDO was used as a polymer matrix for the encapsulation of capsaicin. The results showed that the rate of capsaicin release from the polymer matrix in a water medium was controlled by the BDO portion and the NS content. After use, it was easily degraded in natural soil.

36 MATERIALS SCIENCE↗

Thermal, Rheological and Mechanical Properties of PETG/rPETG Blends

This paper presents the reuse process of post-consumer printed foils made of glycol-modified poly(ethylene terephthalate) (PETG). Fourier-transform infrared spectroscopy and a scanning electron microscope confirmed that these foils consist of PETG and PS layers. Firstly, foil pieces were immersed in the organic solution to remove all prints and after washing and drying they were extruded into regranulate rPETG pellets. Three types of PETG/rPETG blends were fabricated with the addition of 10, 20 and 30 wt% of virgin PETG. Microscopic analysis of the blends confirmed their homogeneity, as was also shown by the fact that there was only one glass transition peak in the heating curve given by differential scanning calorimetry. Moreover, in the presence of fresh PETG the degradation temperatures of rPETG improved significantly, and the viscosity of all blends was reduced as a result of shortened macromolecule chains in rPETG. Mechanical analysis of the materials showed that all blends have comparable tensile strength and a Young’s modulus that is higher than rPETG but lower than virgin PETG. Elongation at break decreases together with the content of rPETG.

36 MATERIALS SCIENCE↗

The Effect of Thermomechanical Processing on the Tensile, Fatigue, and Creep Behavior of Magnesium Alloy AM60

Tensile, fatigue, fracture toughness, and creep experiments were performed on a commercially available magnesium-aluminum alloy (AM60) after three processing treatments: (1) as-THIXOMOLDED (as-molded), (2) THIXOMOLDED then thermomechanically processed (TTMP), and (3) THIXOMOLDED then TTMP then annealed (annealed). The TTMP procedure resulted in a significantly reduced grain size and a tensile yield strength greater than twice that of the as-molded material without a debit in elongation to failure ({epsilon}{sub f}). The as-molded material exhibited the lowest strength, while the annealed material exhibited an intermediate strength but the highest {epsilon}{sub f} (>1 pct). The TTMP and annealed materials exhibited fracture toughness values almost twice that of the as-molded material. The as-molded material exhibited the lowest fatigue threshold values and the lowest fatigue resistance. The annealed material exhibited the greatest fatigue resistance, and this was suggested to be related to its balance of tensile strength and ductility. The fatigue lives of each material were similar at both room temperature (RT) and 423 K (150 C). The tensile-creep behavior was evaluated for applied stresses ranging between 20 and 75 MPa and temperatures between 373 and 473 K (100 and 200 C). During both the fatigue and creep experiments, cracking preferentially occurred at grain boundaries. Overall, the results indicate that thermomechanical processing of AM60 dramatically improves the tensile, fracture toughness, and fatigue behavior, making this alloy attractive for structural applications. The reduced creep resistance after thermomechanical processing offers an opportunity for further research and development.

36 MATERIALS SCIENCE↗

Aluminothermic Reduction Process Under Nitrogen Gas Pressure for Preparing High Nitrogen Austenitic Steels

The aluminothermic reduction casting process under nitrogen gas pressure to make austenitic Cr-Mn-N (Ni-free) and Cr-N (Ni/Mn-free) high nitrogen stainless steels was investigated. Thermodynamic simulation of the redox reaction depending on process parameters was performed. As a result, the optimal ratio of aluminum to oxygen in the initial powder mixture to obtain the highest yield of metal product with minimal aluminum nitride contamination was predicted to be slightly greater than the stoichiometric ratio of 1.125. Microstructures of aluminothermic 26Cr1N and 23Cr9Mn1N steels, prepared taking into account the results of thermodynamic simulation, were investigated by X-ray diffraction, metallography, and transmission electron microscopy. The as-cast microstructure was a pseudo-pearlite (layered ferrite-nitride mixture) in 26Cr1N steel and a ferrite-austenite with signs of discontinuous austenite decomposition in 23Cr9Mn1N steel. After hot forging and subsequent water quenching from 1200 °C, the microstructure was fully austenitic in both steels. Tensile tests of quenched 23Cr9Mn1N steel showed a combination of high strength (ultimate strength of 1324 MPa) and ductility (elongation of 27 pct). The results illustrate that the aluminothermic casting process for producing high nitrogen steel is competitive with the commonly used methods, such as pressure electroslag remelting, both in terms of cost and mechanical properties of manufactured steel.

36 MATERIALS SCIENCE↗

Effect of Aging Treatment on the Precipitation Behavior and Mechanical Properties of Mg-9Gd-3Y-1.5Zn-0.5Zr Alloy

Aging heat treatments of an extruded Mg-9Gd-3Y-1.5Zn-0.5Zr (wt.%) alloy at 200, 225, and 250 °C for various times were studied. The results show that dynamic recrystallization (DRX) occurred during the extrusion process and the alloy exhibited a significant aging hardening response at temperatures ranging from 200 to 225 °C. The precipitation sequence of the alloy at 225 °C was supersaturated solid solution (SSSS) → β″ (D0{sub 19}, Mg{sub 3}RE) → β′ (bco, Mg{sub 15}RE{sub 3}), where the β′ phase was the primary precipitated phase. A large amount of discontinuous lamellar-shaped 14H-structure long period stacking ordered (LPSO) phase was also observed in the α-Mg matrix before and after aging treatments. Owing to the combined strengthening effect of fine DRXed grains, β′ nanoparticles, and widespread LPSO phases, the ultimate tensile strength and tensile yield strength of the peak-aged extruded alloy reached 409 and 303 MPa, respectively. The elongation in this circumstance was ~7.1%, which was slightly lower than that of the alloy before aging treatment.

36 MATERIALS SCIENCE↗

Fabrication of AZ31/MWCNTs Surface Metal Matrix Composites by Friction Stir Processing: Investigation of Microstructure and Mechanical Properties

The surface metal matrix composites of AZ31 Mg alloy reinforced with multiwall carbon nanotubes (MWCNTs) have been fabricated through the friction stir processing by a conventional and two stepped tools. The microstructure and mechanical properties of fabricated composites were studied by optical and electron microscopy, microhardness and tensile tests, respectively. The processing has developed a fine-grain structure along with good distribution of reinforcements. The hardness and tensile strength of fabricated MWCNT/AZ31 composites are generally higher than as-received and FSPed samples. The accumulative effect of grain refinement and reinforcing nanotubes is assumed to be the reason for increasing the ductility after friction stir processing. The hardness is nearly doubled for FSPed samples and some more for nanocomposites compared with the as-received sample. The elongation of nanocomposites is about two times greater than that of the as-rolled sample. The speed ratio, pass number and CNT amount are three important factors influencing the resulting microstructure and mechanical properties. The stepped tools also give a more uniform distribution of reinforcement and higher grain refinement.

36 MATERIALS SCIENCE↗

EBSD Analysis of Relationship Between Microstructural Features and Toughness of a Medium-Carbon Quenching and Partitioning Bainitic Steel

A multiphase microstructure of bainite, martensite and retained austenite in a 0.3C bainitic steel was obtained by a novel bainite isothermal transformation plus quenching and partitioning (B-QP) process. The correlations between microstructural features and toughness were investigated by electron backscatter diffraction (EBSD), and the results showed that the multiphase microstructure containing approximately 50% bainite exhibits higher strength (1617 MPa), greater elongation (18.6%) and greater impact toughness (103 J) than the full martensite. The EBSD analysis indicated that the multiphase microstructure with a smaller average local misorientation (1.22°) has a lower inner stress concentration possibility and that the first formed bainitic ferrite plates in the multiphase microstructure can refine subsequently generated packets and blocks. The corresponding packet and block average size decrease from 11.9 and 2.3 to 8.4 and 1.6 μm, respectively. A boundary misorientation analysis indicated that the multiphase microstructure has a higher percentage of high-angle boundaries (67.1%) than the full martensite (57.9%) because of the larger numbers and smaller sizes of packets and blocks. The packet boundary obstructs crack propagation more effectively than the block boundary.

36 MATERIALS SCIENCE↗

High Strength, Utilizable Ductility and Electrical Conductivity in Cold Rolled Sheets of Cu-Cr-Zr-Ti Alloy

The microstructure and properties of Cu-0.5Cr-0.03Zr-0.04Ti (wt.%) alloy subjected to cold rolling and aging were investigated using hardness and electrical conductivity measurement, tensile testing, and transmission electron microscopy. Plates subjected to 85% reduction in thickness showed significant improvement in the strength compared to solution treated and aged condition. By proper selection of aging temperature, ductility could be significantly improved without reduction in the strength. Aging of the cold rolled sheet at 420 °C for 1 h yielded an ultimate tensile strength and yield strength of 540 and 460 MPa, respectively. On the other hand, total and uniform elongation was 16 and 12%, respectively, with an electrical conductivity of 65 %IACS. The combination of properties achieved after cold rolling and aging is attributed to the higher dislocation density, ultrafine grains and nano-sized chromium precipitates.

36 MATERIALS SCIENCE↗

Tensile Behavior of Electron Beam-Welded and Post-Weld Vacuum-Annealed Nb-10% Hf-1% Ti Refractory Alloy Weldments

Nb-10% Hf-1% Ti refractory alloy is a high performance material extensively used for high temperature applications. Electron beam welding is one of the most widely used techniques to join refractory and reactive alloys. Bigger sizes of nozzles for rocket propulsion applications can be either made through deep drawing and flow turning route or by roll bending and welding route both using sheets/plates as input material for fabrication. The latter is a more economical option for mass production of the hardware using such exotic and expensive alloys. In view of this, both as-welded (AW) coupon and weld plus post-weld vacuum-annealed (AW + VA) coupon have been prepared to study their mechanical behavior. It has been observed that tensile strength and ductility have not been reduced in both these conditions vis-à-vis the base metal, confirming weld efficiency of the alloy to be ~ 100%. Microhardness is found to be 150-160 VHN in the base metal and 200-225 VHN in the weld fusion zone in AW condition, which became uniform (145-155 VHN) throughout the weldment in AW + VA condition. Microstructure of the weldment in AW condition is found to be consisting of grains solidified by epitaxial mode from base metal toward the weld centre. In AW + VA condition, improvement in tensile elongation is observed, which is found to be due to the presence of homogenized grains/more uniform microstructure near the heat-affected zone as compared to the steep gradient in grain size in different zones in the weld in AW condition.

36 MATERIALS SCIENCE↗

Effects of Laser Energies on Wear and Tensile Properties of Biomimetic 7075 Aluminum Alloy

Inspired by the non-smooth surface of certain animals, a biomimetic coupling unit with various sizes, microstructure, and hardness was prepared on the surface of 7075 aluminum alloy. Following experimental studies were conducted to investigate the wear and tensile properties with various laser energy inputs. The results demonstrated that the non-smooth surface with biomimetic coupling units had a positive effect on both the wear resistance and tensile property of 7075 aluminum alloy. In addition, the sample with the unit fabricated by the laser energy of 420.1 J/cm{sup 2} exhibited the most significant improvement on the wear and tensile properties owing to the minimum grain size and the highest microhardness. Also, the weight loss of the sample was one-third of the untreated one’s, and the yield strength, the ultimate tensile strength, and the elongation improved by 20, 20, and 34% respectively. Moreover, the mechanisms of wear and tensile properties improvement were also analyzed.

36 MATERIALS SCIENCE↗

Influence of High Pulsed Magnetic Field on the Dislocations and Mechanical Properties of Al{sub 2}O{sub 3}/Al Composites

At T6 state, Al–Zn–Mg–Cu aluminum matrix composites reinforced with Al{sub 2}O{sub 3} particles generated in situ were subjected to high pulsed magnetic fields at different magnetic induction intensities (B = 2, 3 and 4 T). The results show that the dislocation densities in the treated samples increased with increasing B, and the magnetoplastic effect was determined to be the primary cause. The effect of the magnetic field is believed to alter the spin state of free electrons between dislocations and obstacles from the singlet state (associated with high bonding energy) to the triplet state (low bonding energy). The maximum ultimate tensile strength of 532 MPa was obtained at B = 4 T with 30 pulses, which was 20.7% higher than that of the initial sample, primarily because of dislocation strengthening. At B = 2 T, the elongation was at its maximum of 9.3%, representing an increase of 12% compared with the initial sample, while the associated ultimate tensile strength (447 MPa) was still higher than that of the untreated sample (440 MPa). The relationship between mechanical properties and microstructure was analyzed, and the improved properties observed in this work are explained by the transition of the electron spin state and the piling up of dislocations.

36 MATERIALS SCIENCE↗

Improving Joint Formation and Tensile Properties of Dissimilar Friction Stir Welding of Aluminum and Magnesium Alloys by Solving the Pin Adhesion Problem

Friction stir welding (FSW), as a solid-state welding technology invented by TWI in 1991, has potential to join dissimilar Al/Mg alloys. In this study, the pin adhesion phenomenon affecting joint quality during FSW of 6061-T6 aluminum and AZ31B magnesium alloys was investigated. The adhesion phenomenon induced by higher heat input easily transformed the tapered-and-screwed pin into a tapered pin, which greatly reduced the tool’s ability to drive the plasticized materials and further deteriorated joint formation. Under the condition without the pin adhesion, the complex intercalated interlayer at the bottom of stir zone was beneficial to mechanical interlocking of Al/Mg alloys, improving tensile properties. However, the formation of intermetallic compounds was still the main reason of the joint fracture, significantly deteriorating tensile properties. Under the welding speed of 60 mm/min without the pin adhesion phenomenon, the maximum tensile strength of 107 MPa and elongation of 1.2% were achieved.

36 MATERIALS SCIENCE↗

Properties of Rolled AZ31 Magnesium Alloy Sheet Fabricated by Continuous Variable Cross-Section Direct Extrusion

Rolling is currently a widely used method for manufacturing and processing high-performance magnesium alloy sheets and has received widespread attention in recent years. Here, we combined continuous variable cross-section direct extrusion (CVCDE) and rolling processes. The microstructure and mechanical properties of the resulting sheets rolled at different temperatures from CVCDE extrudate were investigated by optical microscopy, scanning electron microscope, transmission electron microscopy and electron backscatter diffraction. The results showed that a fine-grained microstructure was present with an average grain size of 3.62 μm in sheets rolled from CVCDE extrudate at 623 K. Dynamic recrystallization and a large strain were induced by the multi-pass rolling, which resulted in grain refinement. In the 573-673 K range, the yield strength, tensile strength and elongation initially increased and then declined as the CVCDE temperature increased. The above results provide an important scientific basis of processing, manufacturing and the active control on microstructure and property for high-performance magnesium alloy sheet.

36 MATERIALS SCIENCE↗

Tensile Deformation Temperature Impact on Microstructure and Mechanical Properties of AISI 316LN Austenitic Stainless Steel

Uniaxial tensile tests were conducted on AISI 316LN austenitic stainless steel from − 40 to 300 °C at a rate of 0.5 mm/min. Microstructure and mechanical properties of the deformed steel were investigated by optical, scanning and transmission electron microscopies, x-ray diffraction, and microhardness testing. The yield strength, ultimate tensile strength, elongation, and microhardness increase with the decrease in the test temperature. The tensile fracture morphology has the dimple rupture feature after low-temperature deformations and turns to a mixture of transgranular fracture and dimple fracture after high-temperature ones. The dominating deformation microstructure evolves from dislocation tangle/slip bands to large deformation twins/slip bands with temperature decrease. The deformation-induced martensite transformation can only be realized at low temperature, and its quantity increases with the decrease in the temperature.

36 MATERIALS SCIENCE↗

Study on the Microstructure, Mechanical Properties and Corrosion Behavior of Mg-Zn-Ca Alloy Wire for Biomaterial Application

Due to their excellent biocompatibility and biodegradability, magnesium alloy wires have attracted much attention for biomaterial applications including orthopedic K-wires and sutures in wound closure. In this study, Mg-3Zn-0.2Ca alloy wires were prepared by cold drawing combined with proper intermediate annealing process. Microstructures, texture, mechanical properties and corrosion behavior of Mg-3Zn-0.2Ca alloy wire in a simulated body fluid were investigated. The results showed that the secondary phase and average grain size of the Mg-3Zn-0.2Ca alloy were refined in comparison with the as-extruded alloy and a strong (0002)<10-10>//DD basal fiber texture system was formed after multi-pass cold drawing. After the annealing, most of the basal planes were tilted to the drawing direction (DD) by about 35°, presenting the characteristics of random texture, and the texture intensity decreased. The as-annealed wire shows good mechanical properties with the ultimate tensile strength (UTS), yield strength (YS) and elongation of 253 ± 8.5 MPa, 212 ± 11.3 MPa and 9.2 ± 0.9%, respectively. Electrochemical and hydrogen evolution measurements showed that the corrosion resistance of the Mg-3Zn-0.2Ca alloy wire was improved after the annealing. The immersion test indicated that the Mg-3Zn-0.2Ca wire exhibited uniform corrosion behavior during the initial period of immersion, but then exhibited local corrosion behavior.

36 MATERIALS SCIENCE↗