Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Finite-Temperature Behavior of PdH x Elastic Constants Computed by Direct Molecular Dynamics

In this paper, robust time-averaged molecular dynamics has been developed to calculate finite-temperature elastic constants of a single crystal. We find that when the averaging time exceeds a certain threshold, the statistical errors in the calculated elastic constants become very small. We applied this method to compare the elastic constants of Pd and PdH 0.6 at representative low (10 K) and high (500 K) temperatures. The values predicted for Pd match reasonably well with ultrasonic experimental data at both temperatures. In contrast, the predicted elastic constants for PdH 0.6 only match well with ultrasonic data at 10 K; whereas, at 500 K, the predicted values are significantly lower. We hypothesize that at 500 K, the facile hydrogen diffusion in PdH 0.6 alters the speed of sound, resulting in significantly reduced values of predicted elastic constants as compared to the ultrasonic experimental data. Finally, literature mechanical testing experiments seem to support this hypothesis.

36 MATERIALS SCIENCE↗

Nanoindentation of high-purity vapor deposited lithium films: The elastic modulus

Nanoindentation has been used to measure the elastic modulus of 5 and 18 μm thick high-purity vapor deposited polycrystalline lithium films at 31 °C. Over indentation depths ranging from 150 to 1100 nm, the modulus is found to vary with film thickness from 9.8 GPa ± 11.9% to 8.2 GPa ± 14.5%. These results are well within the range of lithium's orientation dependent elastic modulus, which spans approximately 3.1 to 21.4 GPa. The measured values may also indicate (111) and (100) texture for the 5 and 18 μm thick films, respectively. The potential effects of pileup and surface contamination are found to be negligible if any at all. Small but discernible changes in damping capability near the free surface may provide insight into the subsurface defect structure and the potential for localized heating. In conclusion, numerous experimental challenges are addressed and key metrics are used to validate the measured elastic modulus.

36 MATERIALS SCIENCE↗

Effect of micron-scale manufacturing flaws on the tensile response of centimeter sized two-photon polymerization microlattices

Two-photon polymerization (TPP) is a unique fabrication technique that enables sub-micron scale resolution. Herein, we report on uniaxial tensile tests on millimeter-sized TPP log-pile structures that were fabricated using a recently developed interdigitated stitching strategy. As expected, the Young’s modulus increased with laser intensity, however elastic modulus, ultimate strength and strain-at-failure varied widely, even for nominally identical samples. Post-mortem analysis revealed a series of print defects resulting from various sources including misalignments, resin shrinkage, laser beam shadowing, and local depletion of the oxygen inhibitor. While some of the defects can be eliminated, such as misalignments due to insufficient precision of the mechanical stage, others are more intrinsic to TPP and thus more difficult to address.

36 MATERIALS SCIENCE↗

On the 3D printing of polyelectrolyte complexes: A novel approach to overcome rheology constraints

Strong polyelectrolytes, poly(styrene sulfonate) (PSS), and poly(diallyldimethylammonium) (PDADMAC) dissolved in aqueous KBr can be 3D printed for the first time in the air via direct ink writing (DIW). Viscous polyelectrolyte complex (PEC) solutions were deposited layer-by-layer and quenched with deionized water to produce mechanically viable, viscoelastic hydrogel objects. Optimal inks were confirmed by rheology and thermogravimetric measurements to map flow behavior with material composition. Finally, post-print handling and storage protocols were developed to produce printed resolutions more consistent with conventional DIW.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimizing Interacting Potentials to Form Targeted Materials Structures

Conventional applications of the principles of statistical mechanics (the "forward" problems), start with particle interaction potentials, and proceed to deduce local structure and macroscopic properties. Other applications (that may be classified as "inverse" problems), begin with targeted configurational information, such as low-order correlation functions that characterize local particle order, and attempt to back out full-system configurations and/or interaction potentials. To supplement these successful experimental and numerical "forward" approaches, we have focused on inverse approaches that make use of analytical and computational tools to optimize interactions for targeted self-assembly of nanosystems. The most original aspect of our work is its inherently inverse approach: instead of predicting structures that result from given interaction potentials among particles, we determine the optimal potential that most robustly stabilizes a given target structure subject to certain constraints. Our inverse approach could revolutionize the manner in which materials are designed and fabricated. There are a number of very tangible properties (e.g. zero thermal expansion behavior), elastic constants, optical properties for photonic applications, and transport properties.

36 MATERIALS SCIENCE↗

Inversion for Eigenvalues and Modes Using Sierra-SD and ROL.

In this report we formulate eigenvalue-based methods for model calibration using a PDE-constrained optimization framework. We derive the abstract optimization operators from first principles and implement these methods using Sierra-SD and the Rapid Optimization Library (ROL). To demon- strate this approach, we use experimental measurements and an inverse solution to compute the joint and elastic foam properties of a low-fidelity unit (LFU) model.

42 ENGINEERING↗

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites. Topical Report

This project aimed to integrate, optimize, and validate the fiber orientation and length distribution models previously developed and implemented in the Autodesk® Simulation Moldflow® Insight (ASMI) software package for injection-molded long-carbon-fiber (LCF) thermoplastic composite structures. The project was organized into two phases. Phase 1 demonstrated the ability of the advanced ASMI package to predict fiber orientation and length distributions in LCF/polypropylene (PP) and LCF/polyamide-6, 6 (PA66) plaques within 15% of experimental results. Phase 2 validated the advanced ASMI package by predicting fiber orientation and length distributions within 15% of experimental results for a complex three-dimensional (3D) Toyota automotive part injection-molded from LCF/PP and LCF/PA66 materials. Work under Phase 2 also included estimate of weight savings and cost impacts for a vehicle system using ASMI and structural analyses of the complex part. The present report summarizes the completion of Phases 1 and 2 work activities and accomplishments achieved by the team comprising Pacific Northwest National Laboratory (PNNL); Purdue University (Purdue); Virginia Polytechnic Institute and State University (Virginia Tech); Autodesk, Inc. (Autodesk); PlastiComp, Inc. (PlastiComp); Toyota Research Institute North America (Toyota); Magna Exteriors and Interiors Corp. (Magna); and University of Illinois. Figure 1 illustrates the technical approach adopted in this project that progressed from compounding LCF/PP and LCF/PA66 materials, to process model improvement and implementation, to molding and modeling LCF/PP and LCF/PA66 plaques. The lessons learned from the plaque study and the successful validation of improved process models for fiber orientation and length distributions for these plaques enabled the project to go to Phase 2 to mold, model, and optimize the 3D complex part.

42 ENGINEERING↗

Evaluation of Thermal Neutron Scattering Cross Section of Uranium Silicide with Ab Initio Lattice Dynamics

Uranium silicide (U 3 Si 2 ) is a candidate material for the high-density nuclear fuel in commercial light water reactors [1], [2]. Its higher uranium density, 11.3 g-U/cm3, compared to that of uranium dioxide (UO 2 ), 9.7 g-U/cm3, can improve the performance of a nuclear reactor while using low enriched uranium (LEU) and diversify the choice of cladding materials [1]–[3]. It also has a higher thermal conductivity than UO 2 , which can reduce the thermal stress on the material caused by a temperature gradient across the fuel pellet and provide a larger margin for some postulated accidents [1], [2], [4]. Furthermore, compared to U3Si, another high-density fuel candidate, it has better resistance to in-pile swelling due to less irradiation-induced rapid amorphization [1], [3]. Corresponding to its importance in nuclear engineering, many previous studies have reported the properties of U3Si2. Experiments showed that U 3 Si 2 is a paramagnetic (PM) metal, where a slight linear increase in magnetic susceptibility was measured with increasing temperature [5], [6]. In addition, thermodynamic quantities such as thermal expansion coefficient, heat capacity, and thermal conductivity were experimentally determined over a wide temperature range [1], [7], [8]. In several computational studies, ab initio atomistic simulations based on density functional theory (DFT) were performed to calculate various properties including elastic constants, electronic density of states (DOS), and phonon dispersion curves [9]–[12]. Nevertheless, thermal neutron scattering cross sections, which are critical to the prediction of the parameters in reactor physics that are ultimately related to reactor criticality, have not yet been evaluated for U3Si2. The scattering cross section can be calculated from the phonon DOS, or the energy spectrum of lattice vibrations, of the crystalline system [13], [14]. However, there is also no experimental data available for the phonon DOS of U 3 Si 2 . While some computational studies reported the phonon DOS and/or dispersion curves from ab initio simulations [9]–[12], the accuracy cannot be guaranteed because it is unclear whether the spin-polarization behavior of PM U 3 Si 2 was properly described. In the present study, the thermal neutron scattering cross section for U 3 Si 2 is evaluated for the first time by calculating the phonon DOS for U3Si2 from ab initio lattice dynamics (AILD) simulations based on DFT. First, U 3 Si 2 is modeled based on the experimental structure, and AILD simulations are performed on the modeled U3Si2 to optimize the structure. Next, AILD simulations are performed for supercells with atomic displacement to calculate Hellmann-Feynman forces. Based on the calculated forces, partial phonon DOSs for U and Si are obtained, and the thermal neutron scattering law (TSL) for U 3 Si 2 is finally evaluated. To verify the accuracy of the calculations in the present study, the calculation results are compared with experimental data on the structure and heat capacity of U3Si2 [1], [7], [8], [15].

Geometry Optimization↗

Review of Progress in Atomic Force Microscopy

The study of biological samples is one of the most attractive and innovative fields of application of atomic force microscopy AFM. Recent breakthroughs in software and hardware have revolutionized this field and this paper reports on recent trends and describes examples of applications on biological samples. Originally developed for high-resolution imaging purposes, the AFM also has unique capabilities as a nano-indentor to probe the dynamic visco-elastic material properties of living cells in culture. In particular, AFM elastography combines imaging and indentation modalities to map the spatial distribution of cell mechanical properties, which in turn reflect the structure and function of the underlying structure. This paper describes the progress and development of atomic force microscopy as applied to animal and plant cell structures.

47 OTHER INSTRUMENTATION↗

Localizing Clinical Patterns of Blast Traumatic Brain Injury Through Computational Modeling and Simulation

Blast traumatic brain injury is ubiquitous in modern military conflict with significant morbidity and mortality. Yet the mechanism by which blast overpressure waves cause specific intracranial injury in humans remains unclear. Reviewing of both the clinical experience of neurointensivists and neurosurgeons who treated service members exposed to blast have revealed a pattern of injury to cerebral blood vessels, manifested as subarachnoid hemorrhage, pseudoaneurysm, and early diffuse cerebral edema. Additionally, a seminal neuropathologic case series of victims of blast traumatic brain injury (TBI) showed unique astroglial scarring patterns at the following tissue interfaces: subpial glial plate, perivascular, periventricular, and cerebral gray-white interface. The uniting feature of both the clinical and neuropathologic findings in blast TBI is the co-location of injury to material interfaces, be it solid-fluid or solid-solid interface. This motivates the hypothesis that blast TBI is an injury at the intracranial mechanical interfaces. In order to investigate the intracranial interface dynamics, we performed a novel set of computational simulations using a model human head simplified but containing models of gyri, sulci, cerebrospinal fluid (CSF), ventricles, and vasculature with high spatial resolution of the mechanical interfaces. Simulations were performed within a hybrid Eulerian—Lagrangian simulation suite (CTH coupled via Zapotec to Sierra Mechanics). Because of the large computational meshes, simulations required high performance computing resources. Twenty simulations were performed across multiple exposure scenarios—overpressures of 150, 250, and 500 kPa with 1 ms overpressure durations—for multiple blast exposures (front blast, side blast, and wall blast) across large variations in material model parameters (brain shear properties, skull elastic moduli). All simulations predict fluid cavitation within CSF (where intracerebral vasculature reside) with cavitation occurring deep and diffusely into cerebral sulci. These cavitation events are adjacent to high interface strain rates at the subpial glial plate. Larger overpressure simulations (250 and 500kPa) demonstrated intraventricular cavitation—also associated with adjacent high periventricular strain rates. Additionally, models of embedded intraparenchymal vascular structures—with diameters as small as 0.6 mm—predicted intravascular cavitation with adjacent high perivascular strain rates. The co-location of local maxima of strain rates near several of the regions that appear to be preferentially damaged in blast TBI (vascular structures, subpial glial plate, perivascular regions, and periventricular regions) suggest that intracranial interface dynamics may be important in understanding how blast overpressures leads to intracranial injury.

59 BASIC BIOLOGICAL SCIENCES↗