Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Longitudinal aerodynamic characteristics of an externally blown flap powered lift model with several propulsive system simulators

An investigation of a four-engine externally blown flap (EBF) powered-lift transport was conducted in the Langley V/STOL tunnel to determine the effect of different engine configurations on the longitudinal aerodynamic characteristics. The different engine configurations were simulated by five different sets of propulsion simulators on a single aircraft model. Longitudinal aerodynamic data were obtained for each simulator on each flap deflection corresponding to cruise, take-off, and landing at a range of angles of attack and various thrust coefficients. The bypass ratio (BPR) 6.2 engine simulator provided the best lift and drag characteristics of the five simulators tested in the take-off and landing configurations. The poor performance of the BPR 10.0 and 3.2 engine simulators can be attributed to a mismatch of engine-model sizes or poor engine location and orientation. Isolated engine wake surveys indicated that a reasonable assessment of the aerodynamic characteristics of an engine-wing-flap configuration could be made if qualitative information were available which defined the engine wake characteristics. All configurations could be trimmed easily with relatively small horizontal-tail incidence angles; however, the take-off landing configurations required a high-lift tail.

Hoad, D. R.↗
NASA NTRS1975

Wing-tip vanes as vortex attenuation and induced drag reduction devices

Analytical studies have been conducted to examine the feasibility of utilizing wing tip turbines to remove swirl from the wing trailing vortex, and hence reduce the potential for upset of following aircraft. Energy recovery from the turbines is also analyzed. A computer routine has been developed to permit rapid parametric studies of various tip turbine designs. It is shown that the optimum turbine is a non-rotating set of vanes which reduce swirl and recover energy in the form of reduced overall configuration induced drag. A specific case study indicates a 23% reduction in induced drag for a rectangular wing of aspect ratio 5.33, operated at a lift coefficient at 1.0.

Wentz, W. H., Jr.↗
NASA NTRS1976

Experimental effects of fuselage camber on longitudinal aerodynamic characteristics of a series of wing-fuselage configurations at a Mach number of 1.41

An experimental investigation was conducted to evaluate a method for the integration of a fighter-type fuselage with a theoretical wing to preserve desirable wing aerodynamic characteristics for efficient maneuvering. The investigation was conducted by using semispan wing fuselage models mounted on a splitter plate. The models were tested through an angle of attack range at a Mach number of 1.41. The wing had a leading edge sweep angle of 50 deg and an aspect ratio of 2.76; the wing camber surface was designed for minimum drag due to lift and was to be self trimming at a lift coefficient of 0.2 and at a Mach number of 1.40. A series of five fuselages of various camber was tested on the wing.

Dollyhigh, S. M.↗
NASA NTRS1978

Wind-tunnel test results of a full-scale multicyclic controllable twist rotor

Results of wind tunnel testing of a multicyclic controllable twist rotor at several flight conditions and advance ratios of 0.22 and 0.33 are evaluated. It is found that blade flatwise bending moments and root control actuator loads (fixed system) can be reduced with multicyclic control. Flatwise bending moment reductions of 22-30% with concurrent 83% reductions in control loads were predicted. Analysis of profile power changes indicates a decrease in profile power coefficient of 0.00016, corresponding to a loss of 0.12 sq m of equivalent drag area.

Mccloud, J. L., III↗
NASA NTRS1981

Wind-tunnel results for a modified 17-percent-thick low-speed airfoil section

Wind-tunnel tests were conducted in the Langley low-turbulence pressure tunnel to evaluate the effects on performance of modifying a 17-percent-thick low-speed airfoil. The airfoil contour was altered to reduce the pitching-moment coefficient by increasing the forward loading and to increase the climb lift-drag ratio by decreasing the aft upper surface pressure gradient. The tests were conducted over a Mach number range from 0.07 to 0.32, a chord Reynolds number range 1.0 x 10 to the 6th power to 12.0 x 10 to the 6th power, and an angle-of-attack range from about -10 deg to 20 deg.

Mcghee, R. J.↗
NASA NTRS1982

Rime ice accretion and its effect on airfoil performance

A methodology was developed to predict the growth of rime ice, and the resulting aerodynamic penalty on unprotected, subcritical, airfoil surfaces. The system of equations governing the trajectory of a water droplet in the airfoil flowfield is developed and a numerical solution is obtained to predict the mass flux of super cooled water droplets freezing on impact. A rime ice shape is predicted. The effect of time on the ice growth is modeled by a time-stepping procedure where the flowfield and droplet mass flux are updated periodically through the ice accretion process. Two similarity parameters, the trajectory similarity parameter and accumulation parameter, are found to govern the accretion of rime ice. In addition, an analytical solution is presented for Langmuir's classical modified inertia parameter. The aerodynamic evaluation of the effect of the ice accretion on airfoil performance is determined using an existing airfoil analysis code with empirical corrections. The change in maximum lift coefficient is found from an analysis of the new iced airfoil shape. The drag correction needed due to the severe surface roughness is formulated from existing iced airfoil and rough airfoil data. A small scale wind tunnel test was conducted to determine the change in airfoil performance due to a simulated rime ice shape.

Bragg, M. B.↗
NASA NTRS1991

Trim angle measurements in free-flight facilities

The aerodynamic cofficients and trim angle for an aerobrake at Mach 9.2 and 11.8 were found using a combination of experiment and computation. Free-flight tests were performed at NASA Ames Research Center's Hypervelocity Free-Flight Aerodynamic Facility, and the forebody pressure distribution was calculated using a three-dimensional Navier-Stokes code with an effective specific heat ratio. Using the computed drag, lift, and moments to prescribe the number of terms in the aerodynamic coefficient expansions and to specify the values of the higher order terms, the experimental aerodynamic coefficients and trim angle were found using a six-degree-of-freedom, weighted, least-squares analysis. The experimental and computed aerodynamic coefficients and trim angles are in good agreement. The trim angle obtained from the free-flight tests, 14.7 deg, differs from the design trim angle, 17 deg, and from the Langley wind tunnel results, 12 deg in air and 17 deg in CF4. These differences are attributable to real-gas effects.

Yates, Leslie A.↗
NASA NTRS1952

Experimental Study of the Effects of Finite Surface Disturbances and Angle of Attack on the Laminar Boundary Layer of an NACA 64A010 Airfoil with Area Suction

A Langley low-turbulence wind-tunnel investigation of a porous NACA 64A010 airfoil section has been made to determine the effectiveness of area suction in maintaining full-chord laminar flow behind finite disturbances and at angles of attacks other than 0 degrees. Aero suction resulted in only a small increase in the size of a finite disturbance required to cause premature boundary-layer transition as compared with that for the airfoil without suction. Combined wake and suction drags lower than the drag of the plain airfoil were obtained through a range of low lift coefficient by the use of area suction.

FLOW, LAMINAR↗
NASA NTRS1940

The calculated effect of various hydrodynamic and aerodynamic factors on the take-off of a large flying boat

Report presents the results of an investigation made to determine the influence of various factors on the take-off performance of a hypothetical large flying boat by means of take-off calculations. The factors varied in the calculations were size of hull (load coefficient), wing setting, trim, deflection of flap, wing loading, aspect ratio, and parasite drag. The take-off times and distances were calculated to the stalling speeds and the performance above these speeds was separately studied to determine piloting technique for optimum take-off.

Olson, R E↗
NASA NTRS1950

An Investigation of the Longitudinal Characteristics of the MX-656 Configuration Using Rocket-Propelled Models Preliminary Results at Mach Numbers from 0.65 to 1.25

A rocket-propelled model of the Mx-656 configuration has been flown through the Mach number range from 0.65 to 1.25. An analysis of the response of the model to rapid deflections of the horizontal tail gave information on the lift, drag, longitudinal stability and control, and longitudinal-trim change. The lift-coefficient range covered by the test was from -0.2 to 0,3 throughout most of the Mach number range, The model was statically and dynamically stable throughout the lift-coefficient and Mach number range of the test. At subsonic speeds the aerodynamic center moved f o m r d with increasing lift coefficient. The most forward position of the aerodynamic center was about 12,5 percent of the mean aerodynamic chord at a small positive lift coefficient and at a Mach number of about 0.84. A t supersonic speeds the aerodynamic center was well aft, varying from 33 to 39 percent of the mean aerodynamic chord at Mach numbers of 1.0 and 1.25, respectively. Transonic-trim change, as measured by the change in trim lift coefficient with Mach number at a constant t a i l setting, was of small magnitude (about 0.1 lift coefficient for zero tail setting). The zero-lift/drag coefficient increased about 0.042 in the region between a Mach number of 0.9 and 1.1

Mitchell, Jesse L.↗
NASA NTRS1984

Meteorological accuracy requirements for aerobraking orbital transfer vehicles

Accuracy requirements for the prediction of atmospheric density for a transfer mission from geosynchronous orbit to low earth orbit using an aerobraking orbital transfer vehicle are presented. Uniform density variations such as would occur seasonally and diurnally were considered as well as density 'pockets' similar to what may have been observed on some of the Space Shuttle Orbiter entry flights. Variations in the lift-to-drag ratio from 0.3 to 1.5 were evaluated, with the values of the ratio of the vehicle weight to the product of the aerodynamic lift coefficient and the aerodynamic reference area ranging from 20 to 100 lb/sq ft. The results of the study indicated no problems for the range of lift-to-drag ratio values considered for uniform density variations of at least + or - 50 percent. However, density 'pockets' created problems if variations of + or - 30 percent from nominal occurred over altitude ranges of 1,000 to 10,000 ft.

Skalecki, L. M.↗
NASA NTRS1959

Effect of Convex Longitudinal Curvature on the Planing Characteristics of a Surface Without Dead Rise

A hydrodynamic investigation was made in Langley tank no. 1 of a planing surface which was curved longitudinally in the shape of a circular arc with the center of curvature above the model and had a beam of inches and a radius of curvature of 20 beams. The planing surface had length-beam ratio of 9 and an angle of dead rise of 0 deg. Wetted length, resistance, and trimming moment were determined for values of load coefficient C(sub Delta) from -4.2 to 63.9 and values of speed coefficient C(sub V) from 6 to 25. The effects of convexity were to increase the wetted length-beam ratio (for a given lift), to decrease the lift-drag ratio, to move the center of pressure forward, and ta increase the trim for maximum lift-drag ratio as compared with values for a flat surface. The effects were greatest at low trims and large drafts. The maximum negative lift coefficient C(sub L,b) obtainable with a ratio of the radius of curvature to the beam of 20 was -0.02. The effects of camber were greater in magnitude for convexity than for the same amount of concavity.

Mottard, Elmo J.↗
NASA NTRS1983

Aerodynamic design for improved maneuverability by the use of three-dimensional transonic theory

This study has examined the level of transonic maneuver performance that can be achieved by the use of three-dimensional transonic theory. The FLO-27 code of Jameson and Caughey (1977) was used to lower maneuver drag by the reduction of shock strength on the wing upper surface. A design procedure was used to provide a set of guidelines for the iterative application of FLO-27 during the wing design process. The fighter configuration utilized had a leading-edge sweep of 45 deg and an aspect ratio of 3.28. Tests were conducted at Mach numbers from 0.60 to 0.95 and angles of attack from -5 to 18 deg. The accurate prediction of wing shock systems required the inclusion of fuselage effects in the theory. The FLO-27 code gave a reasonable estimate of the experimental wing pressure distributions at transonic maneuver conditions in the region of the wing where the flow was attached. For Mach numbers between 0.60 and 0.95 and lift coefficients near 0.9, a wing designed by the use of FLO-27 showed substantially lower drag than an empirically developed, supercritical maneuver wing and a maneuver wing designed primarily by two-dimensional transonic theory. For some maneuver conditions, the drag of the two-dimensional design was somewhat lower.

Mann, M. J.↗
NASA NTRS1989

Atmospheric drag model calibrations for spacecraft lifetime prediction

Although solar activity prediction uncertainty normally dominates decay prediction error budget for near-Earth spacecraft, the effect of drag force modeling errors for given levels of solar activity needs to be considered. Two atmospheric density models, the modified Harris-Priester model and the Jacchia-Roberts model, to reproduce the decay histories of the Solar Mesosphere Explorer (SME) and Solar Maximum Mission (SMM) spacecraft in the 490- to 540-kilometer altitude range were analyzed. Historical solar activity data were used in the input to the density computations. For each spacecraft and atmospheric model, a drag scaling adjustment factor was determined for a high-solar-activity year, such that the observed annual decay in the mean semimajor axis was reproduced by an averaged variation-of-parameters (VOP) orbit propagation. The SME (SMM) calibration was performed using calendar year 1983 (1982). The resulting calibration factors differ by 20 to 40 percent from the predictions of the prelaunch ballistic coefficients. The orbit propagations for each spacecraft were extended to the middle of 1988 using the calibrated drag models. For the Jaccia-Roberts density model, the observed decay in the mean semimajor axis of SME (SMM) over the 4.5-year (5.5-year) predictive period was reproduced to within 1.5 (4.4) percent. The corresponding figure for the Harris-Priester model was 8.6 (20.6) percent. Detailed results and conclusions regarding the importance of accurate drag force modeling for lifetime predictions are presented.

Binebrink, A. L.↗
NASA NTRS2014

Improving FermiI Orbit Determination and Prediction in an Uncertain Atmospheric Drag Environment

Orbit determination and prediction of the Fermi Gamma-ray Space Telescope trajectory is strongly impacted by the unpredictability and variability of atmospheric density and the spacecrafts ballistic coefficient. Operationally, Global Positioning System point solutions are processed with an extended Kalman filter for orbit determination, and predictions are generated for conjunction assessment with secondary objects. When these predictions are compared to Joint Space Operations Center radar-based solutions, the close approach distance between the two predictions can greatly differ ahead of the conjunction. This work explores strategies for improving prediction accuracy and helps to explain the prediction disparities. Namely, a tuning analysis is performed to determine atmospheric drag modeling and filter parameters that can improve orbit determination as well as prediction accuracy. A 45 improvement in three-day prediction accuracy is realized by tuning the ballistic coefficient and atmospheric density stochastic models, measurement frequency, and other modeling and filter parameters.

orbit prediction↗
NASA NTRS1978

Low-speed aerodynamic characteristics of a 16-percent-thick variable-geometry airfoil designed for general aviation applications

Tests were conducted in the Langley low-turbulence pressure tunnel to determine the aerodynamic characteristics of climb, cruise, and landing configurations. These tests were conducted over a Mach number range from 0.10 to 0.35, a chord Reynolds number range from 2.0 x 1 million to 20.0 x 1 million, and an angle-of-attack range from -8 deg to 20 deg. Results show that the maximum section lift coefficients increased in the Reynolds number range from 2.0 x 1 million to 9.0 x 1 million and reached values of approximately 2.1, 1.8, and 1.5 for the landing, climb, and cruise configurations, respectively. Stall characteristics, although of the trailing-edge type, were abrupt. The section lift-drag ratio of the climb configuration with fixed transition near the leading edge was about 78 at a lift coefficient of 0.9, a Mach number of 0.15, and a Reynolds number of 4.0 x 1 million. Design lift coefficients of 0.9 and 0.4 for the climb and cruise configurations were obtained at the same angle of attack, about 6 deg, as intended. Good agreement was obtained between experimental results and the predictions of a viscous, attached-flow theoretical method.

Barnwell, R. W.↗
NASA NTRS2014

Improving Fermi Orbit Determination and Prediction in an Uncertain Atmospheric Drag Environment

Orbit determination and prediction of the Fermi Gamma-ray Space Telescope trajectory is strongly impacted by the unpredictability and variability of atmospheric density and the spacecraft's ballistic coefficient. Operationally, Global Positioning System point solutions are processed with an extended Kalman filter for orbit determination, and predictions are generated for conjunction assessment with secondary objects. When these predictions are compared to Joint Space Operations Center radar-based solutions, the close approach distance between the two predictions can greatly differ ahead of the conjunction. This work explores strategies for improving prediction accuracy and helps to explain the prediction disparities. Namely, a tuning analysis is performed to determine atmospheric drag modeling and filter parameters that can improve orbit determination as well as prediction accuracy. A 45% improvement in three-day prediction accuracy is realized by tuning the ballistic coefficient and atmospheric density stochastic models, measurement frequency, and other modeling and filter parameters.

orbit prediction↗
NASA NTRS1974

Simulation of the Gravsat/Geopause mission

A simulation of the proposed low Gravsat and high Geopause satellite mission is presented. This mission promises fundamental improvements in the accuracy of low order geopotential coefficients by using satellite-to-satellite tracking technology coupled with a global sampling of the gravity field. Ten days of data from six stations are assumed. A drag compensation system for the low satellite is also postulated. The results show a one to two order of magnitude improvement in the accuracy of the low order coefficients through degree 8 and order 6. These results are easily adjusted to reflect a different data accuracy level and low satellite altitude.

Koch, D. W.↗