Silicon concentration and pH controls over competitive or simultaneous incorporation of iodate and chromate into calcium carbonate phases
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
In situ technetium-99 ( 99 Tc) immobilization by Fe(II) associated with clay minerals is a potential cost-effective method for Tc remediation at contaminated sites. The oxidation state of Fe is constantly cycled in sedimentary environments, however the effect of this cycle on Tc reduction and immobilization has not yet been investigated. The objective of this project was therefore to study how multiple cycles of reduction-reoxidation of Fe-rich clay mineral, nontronite, affected its reactivity toward Tc (VII) reduction. Iron-rich nontronite NAu-2 was used as a model clay mineral. NAu-2 suspension was first bioreduced by Shewanella putrefaciens CN32, which was subsequently re-oxidized by air. Three cycles of reduction-oxidation were conducted and bioreduced NAu-2 samples from all three cycles were collected and used for Tc(VII) reduction experiments. Each redox cycle resulted in a small fraction of dissolution of small size and/or poorly crystalline NAu-2. The released Fe(II) from the dissolution was likely adsorbed onto NAu-2 surface/edge sites with a high reactivity. Upon exposure to O2, this reactive Fe(II) fraction was oxidized more rapidly than structural Fe(II) and may have accounted for a two-step reoxidation kinetics of NAu-2 associated Fe(II): rapid oxidation over first few hours followed by slow oxidation. Progressive increase of this reactive fraction of Fe(II), from increased dissolution, accounted for the successively higher rate of bioreduction and reoxidation with increased redox cycles. The same Fe redistribution accounted for two-step Tc(VII) reduction kinetics as well. Rapid Tc(VII) reduction in the first few hours may be attributed to a small fraction of highly reactive Fe(II) at the NAu-2 surface/edge sites, and more steady Tc(VII) reduction over longer time may be carried out by structural Fe(II). Similar to the increased rates of Fe(III) reduction and Fe(II) oxidation, the Tc(VII) reduction rate also increased with redox cycles and could be explained by progressive increase of the reactive Fe(II) on NAu-2 surface/edges. Iron-rich clay minerals undergo important changes after redox cycles, but eventually reach a steady state with continued reactivity toward heavy metals.
Here, we report and discuss results of atom probe tomography (APT) and energy-filtered transmission electron microscopy (EFTEM) applied to a borosilicate glass sample of nuclear interest altered for nearly 26 years at 90°C in a confined granitic medium in order to better understand the rate-limiting mechanisms under conditions representative of a deep geological repository for vitrified radioactive waste. The APT technique allows the 3D reconstruction of the elemental distribution at the reactive interphase with sub-nanometer precision. Profiles of the B distribution at pristine glass/hydrated glass interface obtained by different techniques are compared to show the challenge of accurate measurements of diffusion profiles at this buried interface on the nanometer length scale. Our results show that 1) Alkali from the glass and hydrogen from the solution exhibit anti-correlated 15 ± 3 nm wide gradients located between the pristine glass and the hydrated glass layer, 2) boron exhibits an unexpectedly sharp profile located just at the outside of the alkali/H interdiffusion layer; this sharp profile is more consistent with a dissolution front than a diffusion-controlled release of boron. The resulting apparent diffusion coefficients derived from the Li and H profiles are D Li = 1.5 × 10 -22 m 2 .s -1 and D H = 6.8 × 10 -23 m 2 .s -1 . These values are around two orders of magnitude lower than those observed at the very beginning of the alteration process, which suggests that interdiffusion is slowed at high reaction progress by local conditions that could be related to the porous structure of the interphase. As a result, the accessibility of water to the pristine glass could be the rate-limiting step in these conditions. More generally, these findings strongly support the importance of interdiffusion coupled with hydrolysis reactions of the silicate network on the long-term dissolution rate, contrary to what has been suggested by recent interfacial dissolution-precipitation models for silicate minerals.
Co-injection of oxygen, a significant component in CO 2 streams produced by the oxyfuel combustion process, can cause a significant alteration of the redox state in deep geologic formations during geologic carbon sequestration. The potential impact of co-injected oxygen on the interaction between synthetic CO 2 –brine (0.1 M NaCl) and shale caprock (Gothic shale from the Aneth Unit in Utah) and mobilization of trace metals was investigated at ~ 10 MPa and ~ 75 °C. A range of relative volume percentages of O 2 to CO 2 (0, 1, 4 and 8%) were used in these experiments to address the effect of oxygen on shale–CO 2 –brine interaction under various conditions. Major mineral phases in Gothic shale are quartz, calcite, dolomite, montmorillonite, and pyrite. During Gothic shale–CO 2 –brine interaction in the presence of oxygen, pyrite oxidation occurred extensively and caused enhanced dissolution of calcite and dolomite. Pyrite oxidation and calcite dissolution subsequently resulted in the precipitation of Fe(III) oxides and gypsum (CaSO 4 ·2H 2 O). In the presence of oxygen, dissolved Mn and Ni were elevated because of oxidative dissolution of pyrite. The mobility of dissolved Ba was controlled by barite (BaSO 4 ) precipitation in the presence of oxygen. Dissolved U in the experimental brines increased to ~ 8–14 μg/L, with concentrations being slightly higher in the absence of oxygen than in the presence of oxygen. Experimental and modeling results indicate the interaction between shale caprock and oxygen co-injected with CO 2 during geologic carbon sequestration can exert significant impacts on brine pH, solubility of carbonate minerals, stability of sulfide minerals, and mobility of trace metals. The major impact of oxygen is most likely to occur in the zone near CO 2 injection wells where impurity gases can accumulate. Finally, oxygen in CO 2 –brine migrating away from the injection well will be continually consumed through the reactions with sulfide minerals in deep geologic formations.
We report one of the risks that CO 2 geological sequestration imposes on the environment is the impact of potential CO 2 /brine leakage on shallow groundwater. The reliability of reactive transport models predicting the response of groundwater to CO 2 leakage depends on a thorough understanding of the relevant chemical processes and key parameters affecting dissolved CO 2 transport and reaction. Such understanding can be provided by targeted field tests integrated with reactive transport modeling. A controlled-release field experiment was conducted in Mississippi to study the CO 2 -induced geochemical changes in a shallow sandy aquifer at about 50 m depth. The field test involved a dipole system in which the groundwater was pumped from one well, saturated with CO 2 at the pressure corresponding to the hydraulic pressure of the aquifer, and then re-injected into the same aquifer using a second well. Groundwater samples were collected for chemical analyses from four monitoring wells before, during and after the dissolved CO 2 was injected. In this paper, we present reactive transport models used to interpret the observed changes in metal concentrations in these groundwater samples. A reasonable agreement between simulated and measured concentrations indicates that the chemical response in the aquifer can be interpreted using a conceptual model that encompasses two main features: (a) a fast-reacting but limited pool of reactive minerals that responds quickly to changes in pH and causes a pulse-like concentration change, and (b) a slow-reacting but essentially unlimited mineral pool that yields rising metal concentrations upon decreased groundwater velocities after pumping and injection stopped. During the injection, calcite dissolution and Ca-driven cation exchange reactions contribute to a sharp pulse in concentrations of Ca, Ba, Mg, Mn, K, Li, Na and Sr, whereas desorption reactions control a similar increase in Fe concentrations. Finally, after the injection and pumping stops and the groundwater flow rate decreases, the dissolution of relatively slow reacting minerals such as plagioclase drives the rising concentrations of alkali and alkaline earth metals observed at later stages of the test, whereas the dissolution of amorphous iron sulfide causes slowly increasing Fe concentrations.
We constructed mass balances of both calcium and phosphorus for two watersheds in Big Cypress National Preserve in southwest Florida (USA) to evaluate the time scales over which its striking landscape pattern developed. This low-relief carbonate landscape is dotted with evenly spaced, evenly sized, shallow surface depressions that annually fill with surface water and thus support wetland ecosystems (e.g. cypress domes) embedded in a pine-dominated upland matrix with exposed bedrock. Local and landscape scale feedbacks between hydrology, ecological dynamics and limestone dissolution are hypothesized to explain this karst dissolution patterning. This hypothesis requires the region to be wet enough to initiate surface water storage, which constrains landscape formation to interglacial periods. The time scale therefore would be relatively recent if creation of the observed pattern occurred in the current interglacial period (i.e. Holocene), and older time scales could reflect inherited patterns from previous inter-glacial periods, or from other processes of abiotic karstification. We then determined phosphorus stocks across four landscape compartments and estimated the limestone void space (i.e., wetland depression volume) across the landscape to represent cumulative calcium export. We calculated fluxes in (e.g., atmospheric deposition) and out (i.e., solute export) of the landscape to determine landscape denudation rates through mass balance. Comparing stocks and annual fluxes yielded independent estimates of landscape age from the calcium and phosphorus budgets. Our mass balance results indicate that the landscape began to develop in the early-mid Holocene (12,000–5000 ybp). Radiocarbon dating estimates implied similar rates of dissolution (~1 m per 3000–3500 years), and were in agreement with Holocene origin. This supports the hypothesis that ecohydrologic feedbacks between hydrology and vegetation occurring during the present interglacial period are sufficient to shape this landscape into the patterns we see today, and more broadly suggests the potential importance of biota in the development of macro-scale karst features.
Reconstructing the ancient marine cycle of Ni, a trace metal in the oceans essential to enzymes regulating the C, N, and O cycles, would inform how Ni bioavailability shaped early life. The Ni isotopic composition of seawater (δ 60 Ni SW ) through time could provide insight, but this approach requires sedimentary archives that faithfully record δ 60 Ni SW . Carbonates are an often-used record of seawater chemistry, but contaminants could bias the measured δ 60 Ni of bulk sediment. To isolate the true carbonate-bound δ 60 Ni signal, we optimized a chemical cleaning protocol designed to minimize non‑carbonate Ni contributions and maximize carbonate recovery. We analyzed ODP Site 1007 sediments and evaluated oxidative and reductive pre-cleaning steps and carbonate dissolution protocols. Our results show that only reductive cleaning significantly altered the subsequent carbonate leachate composition, lowering Ni/Ca ratios by up to 60% and δ 60 Ni values by as much as 0.4 ‰. In contrast, δ 60 Ni values were largely insensitive to premature carbonate dissolution during pre-cleaning or to partial leaching of silicates during carbonate dissolution, even at higher acid molarities or longer reaction times. We recommend an evidence-based protocol that removes hydro-soluble salts and clays, applies reductive cleaning and oxidative cleaning for certain sample compositions, and dissolves carbonate using 0.5 M acetic acid, adjusted to pH 5. Using these results, we infer a ∼ 0.9 ‰ Ni isotopic fractionation between chemically cleaned deep-water carbonates (+0.4 ± 0.1 ‰) and deep seawater. This method development is a key step toward accurately reconstructing ancient marine Ni cycles.
Some electrochemical systems are known to have higher average efficiency when operated under an oscillatory regime. Given the compromise between activity and stability, the stability of electrochemical interfaces in a self-organized, oscillatory state must be taken into account. Here we evaluate the electro-oxidation of methanol and formic acid on platinum under regular and oscillatory conditions, and study the stability by following the Pt dissolution rates in situ with a stationary probe rotating disk electrode (SPRDE) coupled to an inductively coupled plasma mass spectrometer (ICP-MS). Generally speaking, as the electro-oxidation reaction proceeds, the platinum dissolution rate increases considerably. To guarantee Pt stability, the potential must be kept below 1.0 V vs. RHE. Interestingly, no dissolution is detectable when the electrode potential undergoes temporary self-organization, ensuring a stable and active interface.
High-strength TiHfZrNb x high-entropy alloys could become the ideal materials for small-diameter endovascular stents once their corrosion resistance in the physiological milieu is confirmed. Here, this work aims at evaluating the corrosion resistance of a TiHfZrNb x high-entropy-alloys family in Hanks’ solution at 37 °C and revealing the influence of niobium on the mechanisms of dissolution and passivation. The alloys were subjected to a series of static and dynamic electrochemical tests and surface characterization, employing the static/dynamic/cyclic polarizations, impedance spectroscopy, XPS, AFM, and SEM. Results confirm a higher corrosion resistance of the alloys compared to that of CP-Ti and Ti6Al4V. The addition of niobium considerably improves the microstructural homogeneity that ensures a low dissolution rate and a greater resistance of the film due to the lower concentration of point defects. The passive film behaves as an n-type semiconductor and is composed of a mixture of TiO 2 , Nb 2 O 5 , ZrO 2 , and HfO 2 oxides, with the presence of metallic hydroxides on the outermost layer. A detailed description of the niobium influence on the mechanisms of the dissolution and passivation is presented in this work.
This study investigated the electrochemical properties and potential-dependent stability of Cr(II) and Ni(II) in a eutectic LiCl-KCl molten salt at 500 °C under an argon atmosphere using a three-electrode cell configuration with a glassy carbon working electrode, Ag/Ag + reference electrode, and graphite counter electrode. Cyclic voltammetry was employed to characterize the Cr(0)/Cr(II)/Cr(III) and Ni(0)/Ni(II) redox transitions, yielding diffusion coefficients of 0.50 (±0.01) × 10 −5 cm 2 s −1 for Cr(II) and 0.91 (±0.16) × 10 −5 cm 2 s −1 for Ni(II) at 500 °C. The redox stability domains of these species provided insight into the corrosion mechanisms of a Ni-Cr alloy (80–20 wt %) in LiCl-KCl salt. The measured open circuit potential of the alloy corresponded to the range of potentials where the Ni(0) and Cr(II) species are stable, indicating a preferential dissolution of Cr. Immersion testing of the alloy for 336 h confirmed significant Cr depletion (or Ni-enrichment) at the surface layer, corroborating Cr dealloying as the dominant corrosion reaction under open circuit conditions. Additionally, the application of a small anodic overpotential (0.11 V) resulted in selective Cr dissolution while a large anodic overpotential (0.25 V) resulted in co-dissolution of both Cr and Ni. Furthermore, these results demonstrate that the corrosion mechanisms of a Ni-Cr alloy in LiCl-KCl depend upon the applied potential, and thus the redox conditions of the molten salt should be carefully controlled in the design of a redox buffer to mitigate corrosion in molten salt environments.
In this work, we probed the physical and chemical alteration of the carbonate-rich Utica Shale following CO 2 exposure when thin films of water were present at the shale surface. All reaction conditions were examined at 40 °C and CO 2 pressures up to 10.3 MPa for 14 days. CO 2 dissolution in the water layer at 2342 cm -1 and carbonate dissolution and precipitation at 1424, 874, and 712 cm -1 were discerned with in-situ Fourier Transform infrared spectroscopy (FT-IR). Significant etching and pitting from exposure to CO 2 and water were observed with feature relocation scanning electron microscopy (SEM). Application of the density function theory (DFT) for pore size analysis showed that micropores between approximately 0.9 and 2 nm disappeared while the mesopore volume increased after dissolution of carbonate. These results may provide new insights that carbonate rich shales such as the Utica may have a greater potential for alterations of pore space due to the reactivity of CO 2 which may affect 1) how CO 2 storage in shale formations plays a role in Carbon Capture and Storage (CCS) activities, 2) if CO 2 can be utilized as a potential fracturing agent, and 3) whether CO 2 is an effective fluid for enhanced hydrocarbon extraction.
Methane (CH 4 ) dissolution and diffusive mass transfer in liquid hydrocarbon mixtures is of key interest in the context of enhanced oil recovery from tight shales. In this paper, we have studied CH 4 dissolution and diffusion in normal alkane mixtures at a temperature of 50 ⁰C and at pressures of ~8 MPa. For the measurement of CH 4 dissolution/diffusion in bulk liquid hydrocarbon mixtures, we have utilized a high pressure and temperature, constant-volume diffusion (CV-D) setup. Here, we have studied CH 4 diffusion in mixtures with three long-chain normal alkanes: decane (C 10 ), dodecane (C 12 ) and hexadecane (C 16 ). We have measured CH 4 solubility and diffusion in its binary mixtures with each of these three normal alkanes, as well as in ternary and quaternary mixtures. During the experiments, the swelling of the liquid mixture due to CH 4 dissolution was measured in situ via a cathetometer and was subsequently integrated into the data analysis. A key conclusion from this study is that the solubility and transport properties of the multicomponent mixtures can be predicted accurately from binary mixture measurements using an appropriate Equation of State (EOS) and Wilke’s simplification of the classical Maxwell-Stefan (MS) diffusion theory. This observation can facilitate accurate prediction of diffusive mass transfer in more complex liquid hydrocarbon mixtures.
Our limited understanding of mineral reactive surface area contributes to significant uncertainties in quantitative simulations of reactive chemical transport in subsurface processes. Continuum formulations for reactive transport typically use a number of different approximations for reactive surface area, including geometric, specific, and effective surface area. In this work, reactive surface area estimates are developed and evaluated for their ability to predict dissolution rates in a well-stirred flow-through reactor experiment using disaggregated samples from the Nagaoka pilot CO 2 injection site (Japan). The disaggregated samples are reacted with CO 2 acidified synthetic brine under conditions approximating the field conditions and the evolution of solute concentrations in the reactor effluent is tracked over time. The experiments, carried out in fluid-dominated conditions at a pH of 3.2 for 650 h, resulted in substantial dissolution of the sample and release of a disproportionately large fraction of the divalent cations. Traditional reactive surface area estimation methods, including an adjusted geometric surface area and a BET-based surface area, are compared to a newly developed image-based method. Continuum reactive transport modeling is used to determine which of the reactive surface area models provides the best match with the effluent chemistry from the well-stirred reactor. The modeling incorporates laboratory derived mineral dissolution rates reported in the literature and the initial modal mineralogy of the Nagaoka sediment was determined from scanning electron microscopy (SEM) characterization. The closest match with the observed steady-state effluent concentrations was obtained using specific surface area estimates from the image-based approach supplemented by literature-derived BET measurements. To capture the evolving effluent chemistry, particularly over the first 300 h of the experiment, it was also necessary to account for the grain size distribution in the sediment and the presence of a highly reactive volcanic glass phase that shows preferential cation leaching.
Polymetallic nodules from the Clarion and Clipperton Zone of the equatorial Pacific Ocean were studied using X-ray diffraction, X-ray absorption, Fourier-transformed infrared spectroscopy and transmission electron microscopy. Here, this study includes nodules found at the sediment surface as well as subsurface (14–16 cm sediment depth) and deeply buried (530–985 cm sediment depth) nodules. The surface and subsurface nodules are currently under oxic conditions whereas the deeply buried nodules are under suboxic conditions. Surface nodules consist mainly of turbostratic phyllomanganates (7 Å and 10 Å vernadite and Fe-vernadite); todorokite is a minor phase, if present at all. In contrast, subsurface and especially deeply buried nodules predominantly consist of todorokite, which increases in abundance with depth in the sediment. Thus, upon burial of nodules within the shallow sediment, phyllomanganates transform to todorokite, probably through the combined action of time and change in the ambient chemical conditions. Nodules from deeper sediment depth (>500 cm) consist primarily of todorokite and additionally show signs of dissolution. The transformation of phyllomanganates to todorokite and their further dissolution upon nodule burial under suboxic conditions induces modifications in the crystal-chemistry of Ni, Co, and Cu. In surface nodules, Ni and Co are incorporated in the octahedral sheets of phyllomanganates, whereas Cu mainly is located at the edges of those phyllomanganate sheets. In buried nodules Cu and to a lesser extent Ni are incorporated in todorokite by forming outer-sphere complexes within the tunnels. However, Ni is predominantly incorporated within the octahedra of the newly formed todorokite structure. Co is also enriched in the octahedra of todorokite as a result of dissolution of hydrogenetic vernadite and re-incorporation in the more stable Mn-phase formed during the diagenetic transformation. Co enrichment under suboxic conditions after burial within the sediments is noteworthy since Co in surface nodules is characteristic for oxic conditions.
Explore the source record for details and available documents.
Not Available
Geologic carbon sequestration (GCS) is considered a feasible technology for storing substantive volumes of greenhouse gases in subsurface geological formations. In the reservoir, far from carbon dioxide (CO 2 ) injection wells or in post-injection scenarios, diffusion dominates over advection. This condition conjoins with spatially distributed geochemical reactions to induce heterogeneous changes in pore architecture, i.e. pore body and throat sizes or surface roughness. These changes can affect CO 2 transport properties and storage capacity. In this work, we investigated mineral dissolution and precipitation in dolomite samples saturated with a CO 2 -saturated brine at 93 °C and 34.5 MPa, aged without flow. Two rock types samples, i.e. intergranular- and vuggy-dominant, were selected to investigate changes in pore size, porosity and permeability under reactive conditions. Mineral dissolution and precipitation were characterized using scanning electron microscopy. Changes in pore size were quantified via time-domain nuclear magnetic resonance (TD-NMR) transverse relaxation time (T 2 ) and diffusion coefficient (D) distributions. We show that mineral dissolution likely occurs in highly permeable pathways. These observations are confirmed through analysis of (T 2 ) and diffusion coefficient (D) distributions. In contrast to results during CO 2 -enriched brine continuous injection, mineral precipitation was observed in micropores. The leftward shift of the T 2 peaks, corresponding to micropores, also evidenced mineral precipitation in lowpermeability zones. However, microscale alterations resulted only in a subtle increase in porosity and permeability. Results in this study shed light on effects of geochemical reactions on alteration of rock properties in diffusion-dominated regions during CO 2 storage.