Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CORROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Improved Creep and Tensile Properties of a Corrosion Resistant Ni-Based Superalloy Using High Temperature Aging and Nb/Ta Additions

Resistance to creep deformation is essential for cast and wrought Ni-based superalloys in next generation energy systems due to the considerable exposure times required at the operating temperature. Here the amount of precipitate strengthening was increased in variants to Inconel alloy 725 (IN725), a corrosion resistant alloy, to improve its elevated temperature mechanical strength. Additions of Nb or Ta coupled with a high temperature aging (HTA) heat treatment promoted the formation of γ" precipitates and grain boundary phases which led to significant increases in time to failure. The HTA increased the creep life of various alloy formulations as compared to the standard aging heat treatment with a maximum improvement of 371%. The Nb and Ta additions lowered the minimum creep rate (MCR) and had a similar effect on increasing creep life. The positive effect of the additions was more pronounced when coupled with the HTA which employed a higher temperature in the first step of the heat treatment to promote precipitate phase formation. The Ti/Al ratio was used to design alloys with preferential formation of ' or γ" precipitates. Compact morphology precipitates were formed in the alloys with a low Ti/Al ratio. While a low Ti/Al ratio was primarily associated with lower MCRs, the effect on the creep life was less evident than that of the HTA. By using additions of Nb or Ta and a HTA heat treatment, the creep life of IN725 for testing at 973 K (700 °C) and 483 MPa was improved by up to 256%.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of Chemical Species in the Corrosion Barrier Layer on Thermal CO 2 Treated AZ91D Magnesium Alloy with Lithium Nitrate

A unique corrosion barrier layer, formed by thermal CO 2 treatment with LiNO 3 on AZ91D, was characterized to reveal the chemical species and their spatial distribution using the combination of scanning transmission electron microscopy (STEM), energy dispersive spectroscopy (EDS), and electron energy loss spectroscopy (EELS) techniques. Two distinct and spatially segregated phases were identified as Li compound(s) with MgCO 3 and MgO in the surface barrier layer. Finally, based on the characterization results, it is presumed that the reaction of Mg oxide/hydroxide with LiNO 3 and CO 2 occurred preferentially in some local areas where Li compound(s) with MgCO 3 were present, but the unreacted areas contained MgO in the surface barrier layer.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dislocation channel broadening–A new mechanism to improve irradiation-assisted stress corrosion cracking resistance of additively manufactured 316 L stainless steel

Additively manufactured (AM) 316 L stainless steel (SS) after hot isostatic pressing (HIP) was found to exhibit superior resistance to irradiation-assisted stress corrosion cracking (IASCC) in high-temperature water, as compared to wrought 316 L SS. The well-accepted IASCC factors of radiation-induced segregation (RIS) and radiation hardening are not accurate descriptions of IASCC susceptibility in this case. A decreased strain localization along grain boundaries, caused by dislocation channel broadening, was confirmed to suppress crack initiation. A unique distribution of irradiation-induced defects in HIP AM 316 L SS eased dislocation cross-slip compared to those in the wrought counterpart, thus increasing the channel width near the grain boundaries. Here for the first time, this study highlights the importance of dislocation channel broadening as a potential mechanism to further improve the IASCC resistance of 316 L SS and provides direct experimental evidence based on commercial-grade materials.

316L stainless steel↗
DOE OSTI2025

Initiation of dusting corrosion in high-temperature alloys under CO exposure

Carbon monoxide is commonly encountered in energy systems, yet its reactivity with structural alloys—critical heat-resistant components in these systems—has been largely overlooked compared to the well-documented effects of oxidizing gases. In contrast, we demonstrate the high-temperature reaction of CO with NiAl using in-situ low-energy electron microscopy and X-ray photoemission electron microscopy. Our results show that CO dissociates into atomic oxygen and carbon, resulting in two concurrent reactions: selective oxidation of aluminum to form Al 2 O 3 and the initiation of dusting corrosion through carbon dissolution into the alloy and subsequent carbon deposition on the surface. These reactions produce spatially distinct surface products, preventing the formation of a continuous protective Al oxide layer. These results reveal a preference for the dissociative pathway of CO over the classic Boudouard disproportionation reaction that forms CO 2 . These insights not only advance our understanding of CO-induced alloy degradation but also highlight the practical implications for managing alloy stability and optimizing catalysis in carbon-rich environments, such as those in petrochemical processing and hydrocarbon combustion.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Assessment of multi-stage telescopic control rods in a pebble bed reactor. Part II: corrosion and wear performance

To support High-Temperature Gas-Cooled Reactor designs, the effects of corrosion and wear on a SS316L telescopic control rod prototype were investigated in helium at 775 °C with up to 5 ppm oxygen for durations up to 500 h. Three deployment conditions were tested to assess their impact on wear and oxide formation: severe cycles, daily cycles, and gravity-driven deployments. Here, a chromium-rich oxide layer developed on regions exposed to the helium flow, reaching up to 2 µm in the most affected areas. No carburization or decarburization was observed. Oxide breakthrough occurred mainly at grooves and contact points during severe cycling of the telescopic rod, while in the other tests it was limited to contact points. Friction forces increased due to oxide growth and thermal expansion, the latter being the dominant factor, but never enough to hinder rod deployment significantly. Coaxial misalignment of stages was identified as the main potential risk to reliable operation under normal conditions.

Control rod↗
DOE OSTI2021

Corrosion of rebar in concrete. Part II: Literature survey and statistical analysis of existing data on chloride threshold

The literature is reviewed with respect to defining, measuring, and interpreting the chloride threshold (CT). CT was defined with a strong fundamental basis in the Point Defect Model. which also dictates the nature of the statistical analysis of surveyed CT values. A database of CT for various primary and secondary independent variables has been established. Statistical analyses reveal that CT is lognormally distributed, in accordance with the PDM, with most probable values being 0.85, 0.69, and 1.19 for %total Cl/cem, %free Cl/cem, and [Cl - ]/[OH - ], respectively. The breakdown and corrosion potentials follow normal distributions with means of 0.056 and -0.322 V SCE , respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of the ordered and disordered corrosion morphologies on Ni-based alloy in the passive state

We report an order and disorder combined corrosion morphology of dual-phase Ni-based alloy in the passive state. After galvanostatic polarization in the passive region, the surface of the γ(Ni) phase presents amorphous feature while that of the γ′(Ni 3 Al) phase maintains crystalline. The variations in weight percentages of Ni (50.19% → 3.80%), Co (19.24% → 0.65%), Ta (0.85% → 21.19%), and W (5.73% → 43.79%) of γ surface are evident, whereas the composition of γ′ surface is nearly unchanged. The passive film comprises $W^{6+}_{ox}$, $Ta^{5+}_{ox}$, $Cr^{3+}_{ox}$, $Co^{8/3+}_{ox}$, $Ni^{2+}_{hy}$, and $Co^{2+}_{hy}$, and it shows stronger protection effect on the γ phase.

Density functional theory↗
DOE OSTI2020

Investigation of the irradiation effects in additively manufactured 316L steel resulting in decreased irradiation assisted stress corrosion cracking susceptibility

While additive manufacturing (AM) is an area of increasing interest to the nuclear industry, there are significant research and development needs prior to successful implementation of additively manufactured components into reactors. AM steel behaves differently than traditional wrought material, as has been observed in numerous mechanical testing studies. The nuclear industry must also understand the material response to irradiation. This work examines the irradiation damage and the irradiation assisted stress corrosion cracking behavior (IASCC) of both proton irradiated AM and wrought 316L steel. For IASCC testing, specimens were strained to 4% plastic strain in a simulated boiling water reactor environment (288°C, 0.2 µS/cm). Transmission and scanning electron microscopy, confocal microscopy, and X-ray computed tomography were used to examine coupons of the material as well as tensile bars used in the IASCC testing. This work found that the wrought 316L was more susceptible to IASCC than the AM steel, however, some IASCC was observed in the AM steel when tested with the tensile axis parallel to the build direction. Electron microscopy has shown significantly fewer radiation induced voids formed in the AM steel. While the pre-existing pore network in the AM steel may act as a sink to point defects, this is not expected to be the major factor in the reduced swelling observed in the AM steel. The lower density of radiation induced voids was expected to contribute to the IASCC resistance by decreasing the localization of deformation in the irradiated specimens, however, severity of localized deformation in AM steel, measured in dislocation channel spacing and height, was similar or more severe to that found in wrought. In conclusion, the presence of severe cracking in the wrought specimens did not allow for a direct comparison of localized deformation severities between the AM and wrought steel.

Additive manufacturing↗
DOE OSTI2025

A comparative review on cold sprayed cermet coatings and their applications in high temperature corrosion, oxidation and wear resistance

This review article explores the properties and bonding mechanisms specific to cold sprayed cermet coatings, highlighting its contrast with that of pure metals, and pure ceramics. The general cost structure of cold spraying is compared with other thermal spray techniques and the advantages are highlighted. Several cold sprayed cermet coatings with good corrosion, oxidation and wear resistance behavior in elevated temperatures show convincing potential for applications in power generation industries. The important factors that are attributed to producing highly functional cold sprayed cermet coatings are discussed. A strategic approach involving material, equipment, and application specific optimization of the cold spray process is currently relevant and of utmost importance to meet the coating requirements in several industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Demonstration of an All-Refractory Corrosion-Resistant Molten Salt Pumping and Storage Infrastructure Up to 950 degrees C

Concentrating solar power (CSP) with thermal energy storage (TES) has an estimated cost similar to solar photovoltaics (PV) with lithium-ion batteries (LIB), but CSP + TES has the potential for significantly reduced cost by operating above 700 degrees C. However, this requires a TES medium and containment infrastructure which are chemically compatible and do not degrade above 700 degrees C. MgCl2-KCl-NaCl (MKN) salt is a promising medium, but when MKN salt has small amounts of water and oxygen dissolved in it, it excessively corrodes conventional commercial alloys. Here, we consider refractory materials including graphite, carbon-carbon composite (C/C), and molybdenum because they maintain high mechanical strength at elevated temperatures and are expected to resist corrosion by MKN salt. While selection of refractory materials is often constrained by the need to remain chemically stable in air, this work uses an enclosure filled with inert gas to allow the use of materials like graphite and molybdenum. Notably, graphite components can seal against liquids unlike many brittle refractory materials. We demonstrate a centrifugal pump and mechanical seals made of refractory materials in a laboratory-scale circulation loop, which successfully operated continuously for more than 49 h at temperatures ranging from 750 degrees C to 950 degrees C with no mechanical failures or chemical degradation of the refractory materials. To the best of our knowledge, this is the highest temperature molten salt circulation loop that has been successfully developed, and this refractory infrastructure allows for operation at even much higher temperatures (<1600 degrees C) if a storage medium with a lower vapor pressure is used. The principles of this architecture are relevant to other applications with high temperature flowing metals and salts including Generation IV nuclear fission reactors for power production and molten salt electrolysis reactors for metallurgical processing.

14 SOLAR ENERGY↗
DOE OSTI2022

Corrosion resistance of high nickel alloys in solar salt at 600 °C for up to 4000 h

This study focuses on the time dependent performance of the corrosion resistance of IN625, H230 and 740H alloys in the solar salt (60 wt% NaNO3, 40 wt% KNO3, at 600 °C) for up to 4000 h. Alloy IN625 showed the lowest mass change with parabolic oxidation kinetics that tends to stabilize with exposure time. Both 740H and H230 alloys deviated from the parabolic oxidation behavior beyond the 3000 h of exposure. Alloy 740H showed the highest mass loss due to the nonuniform surface oxidation and the high chromium dissolution rate. Internal oxidation was noticed with Alloy H230 due to the high tungsten concentrations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Corrosion and Enhanced Hydrogen Evolution in Electrochemical Reduction of Ammonium Carbamate on Transition Metal Surfaces

Experiments and theory are combined to search for catalyst activity and stability descriptors for the direct reactive capture and conversion (RCC) of CO 2 in ammonia capture solutions using Cu, Ag, Au, Sn, and Ti electrodes. Two major phenomena emerge in RCC that are not predominant in the electrochemical CO 2 reduction (CO 2 R) reaction, namely, the rapid corrosion and restructuring of the catalyst in the presence of the CO 2 -ammonia adducts and the promotion of the competing hydrogen evolution reaction (HER). The prevalence of HER in RCC is correlated to the electrostatic attraction of the protonated amine to the electrode and the repulsion of the captured CO 2 , using the potential of zero charge (PZC). The stability of catalysts under RCC conditions is a function of the applied potential and cannot be readily predicted using binding energy descriptors commonly used in the prediction of CO 2 R activity. Finally, a direct correlation between calculated binding energies of CO 2 R intermediates, atomic oxygen, hydrogen, and ammonia and the activity and stability of transition metals for RCC cannot be found, highlighting the need for descriptors beyond those known for CO 2 R.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Corrosion Resistance of Lignin-Based Thermoplastic Adhesive-Bonded Aluminum Joints

Adhesive-bonded joints are essential for lightweight, multimaterial automotive structures. We developed a lignin-based thermoplastic adhesive with adhesion strength comparable to conventional epoxy adhesives (20–23 MPa), while offering exceptional durability, recyclability, and corrosion resistance. Unlike commercial epoxy adhesives requiring refrigerated storage, our adhesive retains its bonding potential after a year of ambient conditioning. Bonded joints can be repeatedly disassembled and rejoined with less than 2% strength loss. After 500 h of salt fog exposure, the adhesive-bonded aluminum joints exhibited a 24% strength reduction, compared to 61% reduction in strength of joints based on a commercial epoxy adhesive.

Yu, Zeyang [ORNL] (ORCID:0000000209002374)↗
DOE OSTI2024

Alkali cation-induced cathodic corrosion in Cu electrocatalysts

The reconstruction of Cu catalysts during electrochemical reduction of CO 2 is a widely known but poorly understood phenomenon. Herein, we examine the structural evolution of Cu nanocubes under CO 2 reduction reaction and its relevant reaction conditions using identical location transmission electron microscopy, cyclic voltammetry, in situ X-ray absorption fine structure spectroscopy and ab initio molecular dynamics simulation. Our results suggest that Cu catalysts reconstruct via a hitherto unexplored yet critical pathway - alkali cation-induced cathodic corrosion, when the electrode potential is more negative than an onset value (e.g., –0.4 V RHE when using 0.1 M KHCO 3 ). Having alkali cations in the electrolyte is critical for such a process. Consequently, Cu catalysts will inevitably undergo surface reconstructions during a typical process of CO 2 reduction reaction, resulting in dynamic catalyst morphologies. While having these reconstructions does not necessarily preclude stable electrocatalytic reactions, they will indeed prohibit long-term selectivity and activity enhancement by controlling the morphology of Cu pre-catalysts. Alternatively, by operating Cu catalysts at less negative potentials in the CO electrochemical reduction, we show that Cu nanocubes can provide a much more stable selectivity advantage over spherical Cu nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Insights into the mechanisms controlling the residual corrosion rate of borosilicate glasses

Borosilicate glasses are widely used to confine high-level radioactive wastes. The lifetime of these materials could reach hundreds of thousands of years if leaching of the glass into groundwater enables the formation of a passivating gel layer. Even in this regime, the glass will never stop corroding as thermodynamic equilibrium between glass and solution cannot be achieved. Therefore, accurate predictions of glass durability including passivation, require a deep understanding of the mechanisms controlling the so-called residual rate. However, despite tremendous efforts, these mechanisms remain poorly understood. Here, focusing on the behavior of the soluble elements of the International Simple Glass (B, Na, and Ca), we show that the residual rate is controlled by the behavior of B, a glass former supposed to dissolve instantaneously when in contact with water and thus widely considered as an ideal tracer. We then demonstrate that B release is controlled by multiple processes highly dependent on the pH. At the beginning of the passivating layer formation, the hydrolysis of B-O-Si linkages is rate-limiting and has an activation energy of ~60 kJ mol –1 , a value slightly lower than that for breaking Si-O-Si linkages. Once the fraction of closed pores resulting from gel restructuring is high enough, then diffusion of both reactants (water molecules) and some products (mainly B aq , Ca aq ) through the growing gel layer becomes rate-limiting. Consequently, B and Ca accumulate in an inner layer referred to as the active zone, with potential feedback on the B-O-Si hydrolysis. A new paradigm, including B as a key element of the system, is proposed to develop a comprehensive model for the corrosion of borosilicate glass.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The effect of metals on zeolite crystallization kinetics with relevance to nuclear waste glass corrosion

Abstract Geologic disposal of vitrified radioactive material is planned in several countries, but there are remaining uncertainties related to the long-term stability of glass exposed to groundwater. Specifically, the crystallization of aluminosilicate zeolite minerals can accelerate the rate at which glass corrodes and radioactive material is released into the biosphere. In this study, we identify elemental species that may accelerate or suppress zeolite formation using a protocol to examine their effects on zeolite synthesis over a three-day duration. Our results are consistent with previous works demonstrating glass corrosion acceleration in the presence of calcium. Furthermore, we identify two elements—tin and lithium—as inhibitors of zeolite P2 (gismondine, or GIS type) nucleation and, thus, promising components for promoting the long-term durability of glass waste forms.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Modification of Ni-20Cr corrosion dealloying behavior in molten fluorides via cold work induced plastic deformation

The corrosion dealloying behavior of cold-worked (CW) Ni20Cr alloy (wt%) was studied in molten LiF-NaF-KF (or FLiNaK) salts at 600 °C, equal to a homologous temperature (TH) of 0.52. Alloys were cold-rolled to achieve reductions of thickness of 10%, 30%, and 50% introducing plastic deformation and a high density of dislocations. Potentiostatic holds (Eapplied) were applied in two different electrode potential regimes. At 1.75VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, Cr dealloying to Cr(II) and Cr(III) is predominant, while at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, both Ni and Cr are oxidized in molten FLiNaK at 600 °C. In these potential regimes, dealloyed Ni20Cr displayed bicontinuous porosity within the grain interior and at grain boundaries, driven by the high driving force for Cr dissolution and sustained by defect mediated outward solid state diffusion of Cr in parallel with surface diffusion of Ni. The bicontinuous porous structure developed was observed to undergo further coarsening and densification of the Ni-rich ligaments at a higher electrode potential. The main effect of CW observed is the introduction of plastic deformation and dislocation substructures that serve as short-circuit paths for Cr solid state diffusion to surfaces exposed to FLiNaK. This modified the evolution of the bicontinuous porous structure which increased with CW substantially. Kinetic analysis reveals that the Cr dealloying at +1.75 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ and 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ is initially charge transfer controlled, except for the 50% CW condition at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, where the process becomes limited by slow Cr defect mediated bulk diffusion. The rate determining factors are explored and compared to experimental results.

Chan, Ho Lun↗
DOE OSTI2026

Impact of nitrogen on lithium-induced corrosion and cracking of RAFM steel

The emergence of private fusion enterprises, combined with advancements in U.S. and EU ITER-TBM as well as EU DEMO liquid breeder blanket concepts, has renewed focus on the materials challenges. This study examines the compatibility of reduced activation ferritic/martensitic (RAFM) steel in liquid Lithium (Li) containing various Nitrogen (N) concentrations, tested at 600 and 700 °C for 500 and 1000 h under static conditions. Microstructural characterization revealed the corrosion-induced dissolution and precipitation in Li containing 0.082 and 0.17 wt.% N at 600 °C, while limited dissolution and precipitation were observed in N-gettered Li using zirconium (Zr) and titanium (Ti) foils at 600 °C. Tensile testing at room temperature after Li exposure revealed a decrease in strength and ductility of the RAFM steel as a function of N content in Li. Severe embrittlement was observed after 500 h in Li containing 0.17 wt.% N at 600 °C and after 500 h in hot-gettered Li at 700 °C. Chromium (Cr) depletion from the steel matrix was observed, leading to the formation of M6C-type carbides on the surface identified by electron microscopy (SEM), X-ray diffraction (XRD), in agreement with thermodynamic calculations. These findings highlight the critical materials challenges posed by liquid Li breeder blanket concepts, emphasizing the need for improved strategies to address Li-induced dissolution, precipitation, and steel embrittlement due to N contamination of the coolant.

Romedenne, Marie [ORNL] (ORCID:0000000317936561)↗